Adiabatic cooling for cold polar molecules on a chip using a controllable high-efficiency electrostatic surface trap

We propose a controllable high-efficiency electrostatic surface trap for cold polar molecules on a chip by using two insulator-embedded charged rings and a grounded conductor plate. We calculate Stark energy structure pattern of ND3 molecules in an external electric field using the method of matrix diagonalization. We analyze how the voltages that are applied to the ring electrodes affect the depth of the efficient well and the controllability of the distance between the trap center and the surface of the chip. To obtain a better understanding, we simulate the dynamical loading and trapping processes of ND3 molecules in a ｜J, KM = ｜1,-1 state by using classical Monte–Carlo method. Our study shows that the loading efficiency of our trap can reach ～ 88%. Finally, we study the adiabatic cooling of cold molecules in our surface trap by linearly lowering the potential-well depth（i.e., lowering the trapping voltage）, and find that the temperature of the trapped ND3 molecules can be adiabatically cooled from 34.5 m K to ～ 5.8 m K when the trapping voltage is reduced from-35 k V to-3 k V.

Controllable thermal rectification design for buildings based on phase change composites

Phase-change material(PCM)is widely used in thermal management due to their unique thermal behavior.However,related research in thermal rectifier is mainly focused on exploring the principles at the fundamental device level,which results in a gap to real applications.Here,we propose a controllable thermal rectification design towards building applications through the direct adhesion of composite thermal rectification material(TRM)based on PCM and reduced graphene oxide(rGO)aerogel to ordinary concrete walls(CWs).The design is evaluated in detail by combining experiments and finite element analysis.It is found that,TRM can regulate the temperature difference on both sides of the TRM/CWs system by thermal rectification.The difference in two directions reaches to 13.8 K at the heat flow of 80 W/m^(2).In addition,the larger the change of thermal conductivity before and after phase change of TRM is,the more effective it is for regulating temperature difference in two directions.The stated technology has a wide range of applications for the thermal energy control in buildings with specific temperature requirements.

Evaluation of the Effect of High-efficiency Compound Formulations on the Prevention and Control of Sugarcane Brown Stripe

[Objectives]This study was conducted to screen high-efficiency compound formulations and precise application technologies for the prevention and control of sugarcane brown stripe disease.[Methods]Carbendazim,benomyl,chlorothalonil,azoxystrobin,pyraclostrobine and difenoconazole·azoxystrobin were selected for field efficacy tests.[Results]Three formulations,(50%carbendazim WP 1500 g+75%chlorothalonil WP 1500 g+potassium dihydrogen phosphate 2400 g+agricultural synergist 300 ml)/hm^(2),(50%benomyl WP 1500 g+75%chlorothalonil WP 1500 g+potassium dihydrogen phosphate 2400 g+agricultural synergist 300 ml)/hm^(2) and(25%pyraclostrobin 600 ml+potassium dihydrogen phosphate 2400 g+agricultural synergist 300 ml)/hm^(2) had good control effects on sugarcane brown stripe disease,and showed disease index below 14.02 and control efficacy above 84.41%.The three formulations are ideal high-efficiency compound formulations for the prevention and control of sugarcane brown stripe disease.They can be sprayed manually and by unmanned aerial vehicles on the foliar surface from July to August,once every 7 to 10 d,continuously for 2 times.[Conclusions]This study provides new technical support for accurate and efficient prevention and control of sugarcane brown stripe disease.

Evaluation of the Effects of High-efficiency Compound Formulations on the Prevention and Control of Sugarcane Brown Rust

[Objectives]This study was conducted to screen high-efficiency compound formulations and precise application technologies for the prevention and control of sugarcane brown rust. [Methods] Zineb, dinconazole, mancozeb, azoxystrobin, pyraclostrobin, difenoconazole·azoxystrobin, chlorothalonil and carbendazim were selected for field efficacy tests. [Results] Four formulations,(65% zineb WP 1 500 g+75% chlorothalonil WP 1 500 g+potassium dihydrogen phosphate 2 400 g+agricultural synergist 300 ml)/hm^(2),(12.5% dinconazole WP 1 500 g +75% chlorothalonil WP 1 500 g+potassium dihydrogen phosphate 2 400 g+agricultural synergist 300 ml)/hm^(2),(80% mancozeb WP 1 500 g+75% chlorothalonil WP 1 500 g+potassium dihydrogen phosphate 2 400 g+agricultural synergist 300 ml)/hm^(2) and(30% difenoconazole·azoxystrobin SC 900 ml+potassium dihydrogen phosphate 2 400 g+agricultural synergist 300 ml) had good control efficacy on sugarcane brown rust, and showed disease indexes all below 18.79 and control efficacy over 80.53%. The four formulations are ideal high-efficiency compound formulations for the prevention and control of sugarcane brown rust. They can be sprayed manually and by unmanned aerial vehicles on the foliar surface from July to August, once every 7 to 10 d, continuously for 2 times. [Conclusions] This study provides new technical support for accurate and efficient prevention and control of sugarcane rust.

Preparation and hygrothermal performance of composite phase change material wallboard with humidity control based on expanded perlite/diatomite/paraffin

Phase change material(PCM)can reduce the indoor temperature fluctuation and humidity control material can adjust relative humidity used in buildings.In this study,a kind of composite phase change material particles(CPCMPs)were prepared by vacuum impregnation method with expanded perlite(EP)as supporting material and paraffin as phase change material.Thus,a PCM plate was fabricated by mould pressing method with CPCMPs and then composite phase change humidity control wallboard(CPCHCW)was prepared by spraying the diatom mud on the surface of PCM plate.The composition,thermophysical properties and microstructure were characterized using X-ray diffraction instrument(XRD),differential scanning calorimeter(DSC)and scanning electron microscope(SEM).Additionally,the hygrothermal performance of CPCHCW was characterized by temperature and humidity collaborative test.The results can be summarized as follows:(1)CPCMPs have suitable phase change parameters with melting/freezing point of 18.23°C/29.42°C and higher latent heat of 54.66 J/g/55.63 J/g;(2)the diatom mud can control the humidity of confined space with a certain volume;(3)the combination of diatom mud and PCM plate in CPCHCW can effectively adjust the indoor temperature and humidity.The above conclusions indicate the potential of CPCHCW in the application of building energy efficiency.

Adaptive Shape Control for Thermal Deformation of Membrane Mirror with In-plane PVDF Actuators

Optical membrane mirrors are promising key components for future space telescopes. Due to their ultra-thin and high flexible properties, the surfaces of these membrane mirrors are susceptible to temperature variations. Therefore adaptive shape control of the mirror is essential to maintain the surface precision and to ensure its working performance. However, researches on modeling and control of membrane mirrors under thermal loads are sparse in open literatures. A 0.2 m diameter scale model of a polyimide membrane mirror is developed in this study. Three Polyvinylidene fluoride(PVDF) patches are laminated on the non-reflective side of the membrane mirror to serve as in-plane actuators. A new mathematical model of the piezoelectric actuated membrane mirror in multiple fields,(i.e., thermal,mechanical, and electrical field) is established, with which dynamic and static behaviors of the mirror can be analyzed.A closed-loop membrane mirror shape control system is set up and a surface shape control method based on an influence function matrix of the mirror is then investigated. Several experiments including surface displacement tracking and thermal deformation alleviation are performed. The deviations range from 15 μm to 20 μm are eliminated within 0.1 s and the residual deformation is controlled to micron level, which demonstrates the effectiveness of the proposed membrane shape control strategy and shows a satisfactory real-time performance. The proposed research provides a technological support and instruction for shape control of optical membrane mirrors.

Design and Control of Thermally Coupled Reactive Distillation Sequence for Biodiesel Production

Decreasing petroleum reserves and growing alternative fuels requirements have promoted the study of biodiesel production. In this work, two thermally coupled reactive distillation designs for biodiesel production were investigated, and the sensitivity analysis was conducted to obtain the appropriate design values. The thermodynamic analysis and economics evaluation were performed to estimate the superiority of the thermally coupled designs over the base case. The proposed biodiesel production processes were simulated using the simulator Aspen Plus, and calculation results show that the exergy loss and economic cost in the two thermally coupled designs can be greatly reduced. It is found that the thermally coupled side-stripper reactive distillation design provides more economic benefits than the side-rectifier one. The dynamic performance of the thermally coupled side-stripper design was investigated and the results showed that the proposed control structure could effectively handle large feed disturbances.

Bayesian networks modeling for thermal error of numerical control machine tools

The interaction between the heat source location, its intensity, thermal expansion coefficient, the machine system configuration and the running environment creates complex thermal behavior of a machine tool, and also makes thermal error prediction difficult. To address this issue, a novel prediction method for machine tool thermal error based on Bayesian networks (BNs) was presented. The method described causal relationships of factors inducing thermal deformation by graph theory and estimated the thermal error by Bayesian statistical techniques. Due to the effective combination of domain knowledge and sampled data, the BN method could adapt to the change of running state of machine, and obtain satisfactory prediction accuracy. Ex- periments on spindle thermal deformation were conducted to evaluate the modeling performance. Experimental results indicate that the BN method performs far better than the least squares (LS) analysis in terms of modeling estimation accuracy.

Dynamic Thermal Model and Temperature Control of Proton Exchange Membrane Fuel Cell Stack

A dynamic thermal transfer model of a proton exchange membrane fuel cell (PEMFC) stack is developed based on energy conservation in order to reach better temperature control of PEMFC stack. Considering its uncertain parameters and disturbance, we propose a robust adaptive controller based on backstepping algorithm of Lyaponov function. Numerical simulations indicate the validity of the proposed controller.

INVESTIGATION OF SURFACE TEMPERATURE IN HIGH-EFFICIENCY DEEP GRINDING

A new thermal model with triangular heat flux distribution is given in high-efficiency deep grinding. The mathematical expressions are driven to calculate the surface temperature. The transient behavior of the maximum temperature on contact area is investigated in different grinding conditions with a J-type thermocouple. The maximum contact temperatures measured in different conditions are found to be between 1 000 ℃ and 1 500 ℃ in burn-out conditions. The experiment results show good agreement with the new thermal model.

Effect of perceived control on human thermal comfort in heated environments

To study the effects of perceived control on human thermal sensation and thermal comfort in heated environments,a psychological experiment was conducted.In total,24 subjects participated in an experiment.The experiment consisted of two cases in which the indoor temperature was set at 18℃ with different cold radiation temperatures.The experiment lasted for 120 min and was divided into three phases,adaptation,without perceived control and perceived control.In the second phase,the subjects were told in advance that the indoor temperature could not be adjusted.In the third phase,subjects were told that they could adjust the indoor temperature to meet their own thermal expectations,but the indoor temperature could not actually be changed.The results showed that the effect of perceived control on thermal sensation was related to the thermal expectation.For people with strong expectations for a neutral environment,perceived control improved their thermal sensation by satisfying their thermal expectations.For people with low thermal expectations,perceived control reduced their thermal tolerance to the environment,eventually leading to thermal discomfort.These new findings provide more supports for the importance of psychological effects and a reference for the personal control of heating temperatures.

Temperature control for thermal treatment of aluminum alloy in a large-scale vertical quench furnace

The temperature control of the large-scale vertical quench furnace is very difficult due to its huge volume and complex thermal exchanges. To meet the technical requirement of the quenching process, a temperature control system which integrates temperature calibration and temperature uniformity control is developed for the thermal treatment of aluminum alloy workpieces in the large-scale vertical quench furnace. To obtain the aluminum alloy workpiece temperature, an air heat transfer model is newly established to describe the temperature gradient distribution so that the immeasurable workpiece temperature can be calibrated from the available thermocouple temperature. To satisfy the uniformity control of the furnace temperature, a second order partial differential equation(PDE) is derived to describe the thermal dynamics inside the vertical quench furnace. Based on the PDE, a decoupling matrix is constructed to solve the coupling issue and decouple the heating process into multiple independent heating subsystems. Then, using the expert control rule to find a compromise of temperature rising time and overshoot during the quenching process. The developed temperature control system has been successfully applied to a 31 m large-scale vertical quench furnace, and the industrial running results show the significant improvement of the temperature uniformity, lower overshoot and shortened processing time.

Experimental Research of Electronic Devices Thermal Control Using Metallic Phase Change Materials

A Phase-change thermal control unit( PTCU) filled with metallic phase change material( PCM) Bismuth alloy for electric devices thermal protection was developed and investigated experimentally. The PTCU filled with PCM was designed and manufactured. Resistance heating components( RCHs) produced 1 W,3 W, 5 W,7W,and 10 W for simulating heat generation of electronic devices. At various heating power levels,the performance of PTCU were tested during heating period and one duty cycle period. The experimental results show that the PTCU delays RCH reaching the maximum operating temperature. Also,a numerical model was developed to enable interpretation of experimental results and to perform parametric studies. The results confirmed that the PTCU is suitable for electric devices thermal control.

Novel Control Structure Design of Differential Pressure Thermally Coupled Reactive Distillation for Methyl Acetate Hydrolysis

In this paper, the novel control structures of differential pressure thermally coupled reactive distillation process for methyl acetate hydrolysis were proposed. The RadFrac module of Aspen Plus was adopted in the steady-state simulation. Sensitive analysis was applied to find the stable intial value and provide a basis for the improved control structure design. The Aspen Dynamics software was adopted to study the process dynamic behaviors, and two novel control structures provided with feed ratio controllers and sensitive tray temperature controllers were proposed. The reflux ratio controllers were applied in the improved novel control structures. Both control structures abandoned the composition controllers that were replaced by simpler controllers with which the product purity could meet the specification requiring under a ± 20% disturbance to the total feed flowrate / MeAc composition.

SIMULATION IN THERMAL DESIGN FOR ELECTRONIC CONTROL UNIT OF ELECTRONIC UNIT PUMP

The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time

Proposal of Functional Thermal Control Systems for High-Power Micro-Satellite and Its Demonstration under Thermal Vacuum Condition

In previous years, several high-power micro-satellites below ~100 kg have been developed for high-functional spacecraft. This paper proposes a functional and high-power thermal control system with no power supply and a simple configuration for micro-satellite: 100 W, 3 U. The proposed system consists of a heat storage panel (HSP) with pitch type CFRP (Carbon Fiber Reinforced Polymer), a micro loop heat pipe (m-LHP) and a flexible re-deployable radiator (FRDR) as an active thermal control system. The aim of this research is to try not only to verify the thermal control devices, but also to perform a water phase change experiment as a payload using an electric power generation of 100 W in space environment. In this paper, the basic design of the satellite, the analysis of the feasibility by the thermal mathematical model, and the fabrication of thermal test model including water phase chamber are reported. The main results of thermal analysis as feasibility verification showed that the paddles could absorb the thermal energy up to 97 W at the solar input of 180 W, and the operating temperature of bus equipment became within the allowable temperature range (0°C - 40°C). At thermal vacuum test, the difference between the analysis and the experiment for the temperature history of water due to the discordance for the value of thermal conductance was discussed.

Controllable rectification on the thermal conductivity of porous YBa_(2)Cu_(3)O_(7−x) superconductors from 3D-printing

Superconducting YBa_(2)Cu_(3)O_(7−x)(YBCO)bulks have promising applications in quasi-permanent magnets,levitation,etc.Recently,a new way of fabricating porous YBCO bulks,named direct-ink-writing(DIW)3D-printing method,has been reported.In this method,the customized precursor paste and programmable shape are two main advantages.Here,we have put forward a new way to customize the YBCO 3D-printing precursor paste which is doped with Al_(2)O_(3)nanoparticles to obtain YBCO with higher thermal conductivity.The great rheological properties of precursor paste after being doped with Al_(2)O_(3)nanoparticles can help the macroscopic YBCO samples with high thermal conductivity fabricated stably with high crystalline and lightweight properties.Test results show that the peak thermal conductivity of Al_(2)O_(3)-doped YBCO can reach twice as much as pure YBCO,which makes a great effort to reduce the quench propagation speed.Based on the microstructure analysis,one can find that the thermal conductivity of Al_(2)O_(3)-doped YBCO has been determined by its components and microstructures.In addition,a macroscopic theoretical model has been proposed to assess the thermal conductivity of different microstructures,whose calculated results take good agreement with the experimental results.Meanwhile,a microstructure with high thermal conductivity has been found.Finally,a macroscopic YBCO bulk with the presented high thermal conductivity microstructure has been fabricated by the Al_(2)O_(3)-doped method.Compared with YBCO fabricated by the traditional 3D-printed,the Al_(2)O_(3)-doped structural YBCO bulks present excellent heat transfer performances.Our customized design of 3D-printing precursor pastes and novel concept of structural design for enhancing the thermal conductivity of YBCO superconducting material can be widely used in other DIW 3D-printing materials.

Controlled Size and Density Distribution of Nanoparticles by Thermal Ammonia Etching Method

Nickel nanometer catalyst thin films were prepared on SiO2/Si substrates using sputtering coater. The effects of ammonia pretreatment on the catalyst films from continuous film to the nanoparticles were investigated. The nanostructures of the Ni thin films as a function of the catalyst film original thickness, the pretreatment time and temperature were discussed. The optimum parameters of etching process were obtained, and the functional mechanism of ammonia was primarily analyzed. Scanning electron microscopy （SEM） and atomic force microscopy （AFM） were used to evaluate the obtained nanoparticles. It is demonstrated that the controlled size and density distribution of the nanoparticles can be achieved by employing ammonia etching method.

Directional region control of the thermal fractal diffusion of a space body

We present a directional region control （DRC） model of thermal diffusion fractal growth with active heat diffusion in three-dimensional space. This model can be applied to predict the space body heat fractal growth and study its directional region control. When the nonlinear interference term and the inner heat source term are generalized functions, the relationship between the particle aggregation probability and the interference terms can be obtained using the norm theory. We can then predict the aggregation form of particles in different regions. When the nonlinear interference terms in the model are expressed as a trigonometric function and its composite function, our simulations show that the DRC method of thermal fractal diffusion is effective and has reference value for the directional control of actual fractal growth systems.

Guide and control of thermal conduction with isotropic thermodynamic parameters based on a rotary-concentrating device

A rotary-concentrating device for thermal conduction is constructed to control and guide thermal energy transmitting in elastic plates.The designed device has the ability of concentrating for thermal conduction and controlling the processes of thermal diffusion in a plate.The multilayered isotropic material properties of the rotary-concentrating device are derived based on the transformation and rotary medium method and a rotation parameter to control the thermal diffusion process is introduced.The efficiency of the rotary-concentrating device for thermal conduction is verified.Stability of temperature fields in a plate with the rotary-concentrating device is analyzed to study the performance of rotary-concentrating.Numerical examples show that the constructed rotary-concentrating device for thermal conduction can effectively rotate and focus on the thermal energy into the device for a wide range of diffusion temperatures,which can enhance the thermal conduction.Therefore,this study can provide a theoretical support for potential applications in fields of energy harvesting and thermal conduction control.