High-Frequency AlGaN/GaN High-Electron-Mobility Transistors with Regrown Ohmic Contacts by Metal-Organic Chemical Vapor Deposition

Nonalloyed ohmic contacts regrown by metal-organic chemical vapor deposition are performed on AlGaN/GaN high-electron-mobility transistors. Low ohmic contact resistance of 0.15Ω.mm is obtained. It is found that the sidewall obliquity near the regrown interface induced by the plasma dry etching has great influence on the total contact resistance. The fabricated device with a 100-nm T-shaped gate demonstrates a maximum drain current density of 0.95 A/mm at Vgs = 1 V and a maximum peak extrinsic transcondutance Gm of 216mS/ram. Moreover, a current gain cut-off frequency fT of 115 GHz and a maximum oscillation frequency fmax of 127 GHz are achieved.

Characterization and wear behavior of WC-0.8Co coating on cast steel rolls by electro-spark deposition

To prepare high wear resistance and high hardness coatings, electro-spark deposition was adopted for depositing an electrode of a mixture of 92wt%WC＋8wt%Co on a cast steel roll substrate. The coating was characterized by classical X-ray diffractometer （XRD） and scanning electron microscopy （SEM） with energy dispersive X-ray analysis （EDX）. The results indicate that the coating shows nanosized particulate structure and dendritic structure including columnar structure and equiaxed structure. The primary phases of the coating contain Fe3W3C, Co3W3C, Fe2C and Si2W. The coating has a low friction coefficient of 0.13, its average wear-resistance is 3.3 times that of the cast steel roll substrate and the main mechanism is abrasive wear. The maximum microhardness value of the coating is about 1573.9 Hv0.3. The study reveals that the electro-spark deposition process has the characteristic of better coating quality and the coating has higher wear resistance and hardness.

Electro-spark epitaxial deposition of NiCoCrAlYTa alloy on directionally solidified nickel-based superalloy

An 8 mm-high NiCoCrAlYTa coating was epitaxially built-up on a directionally solidified (DS) Ni-based superalloy blade tip by electro-spark deposition.Epitaxial morphologies of the coating and its microstructural characteristics were investigated by means of SEM,XRD and TEM etc.It is observed that the fine column-like dendrites originated from the γ'-particles or γ'-clusters of the DS substrate and are un-continuously coarsened.The β-phase particles precipitate and grow eutectically with the γ-phase.The orientation of fine column dendrites depends on electro-spark deposition processing parameters and the microstructure can be characterized with superfine γ and β phases.

Tribological properties of cobalt-based alloy coating with different cobalt contents by electro-spark deposition

The cobalt-based alloy coating with different Co contents was deposited on 45 steel by electro-spark deposition with the self-made electrode. The coating has a compact and uniform microstructure with low porosity and no visible microcracks. When Co content increases grad- ually, oxygen content of coating samples 1-5 decreases first and then increases in the range of 2.52 wt%-3.05 wt%; sample 3 has the lowest oxygen content of 2.52 %. Mi- crohardness of the coating is improved remarkably com- pared with the substrate （HV 230.18）. With Co content increasing, microhardness of the coating samples 1-5 first rises slightly and then declines rapidly in the range of HV 580.61-1052.33. Sample 3 gets the maximum of HV 1052.33, which is about 4.6 times that of the substrate. The coating presents excellent wear resistance, which first increases and then decreases when Co content increases. Sample 3 shows the best wear resistance of about 6.4 times that of the substrate. Main wear mechanism of the coating is abrasive wear and fatigue wear, along with oxidation wear under high speed or heavy load conditions.

Interface behavior and microstructure transformation of welded joint of 35CrMo steel by electro-spark deposition

Electro-spark deposition has been carried out on the 35CrMo steel by filling and restoring the simulated slot specimens, and continuous surface coating with extra low porosity was obtained with proper parameters. The microstructure transformation and interface behavior of deposited joint were observed and analyzed. It shows that a transition region with 15μm in depth was obtained between base metal and deposited metal, and metallurgical bonding was achieved between restored base metal and deposition coating.

Wear characteristics of spheroidal graphite roll WC-8Co coating produced by electro-spark deposition

Electro-spark deposition（ESD） was adopted for preparing high property coatings by depositing WC-8Co cemented carbide on an spheroidal graphite roll substrate.The microstructure and properties of the coating were investigated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） with energy dispersive X-ray（EDX） and ball-disc configuration wear tester.The results show that nanosized particles and amorphous structures prevail in the coating which is metallurgically bonded to the substrate.The microstructures of the transition zone include columnar structure and equiaxed structure.The primary phases of the coating contain W2C, W6C2.54, Fe3W3C, and Co3W3C.The results of abrasive test show that the coating has low friction coefficients（μaverage = 0.18） and the wear mechanisms are mainly abrasive wear, fatigue wear, and oxidation wear.The maximum microhardness value of the coating is about 17410 N/mm2.The study reveals that the electro-spark deposition process has better coating quality and the coating has high wear resistance and hardness.

Unweldable superalloy component repair using electro-spark deposition with high strength filler material

Nickel-base superalloy components with high Al+Ti content are difficult to weld repair using high strength filler materials with conventional welding methods like TIG welding. A feasibility study of electro-spark deposition (ESD) for unweldable superalloy component repair with a high strength filler material was carried out. SEM analysis reveals that a fully dense, crack-free, metallurgical bonded deposition layer can be obtained on the K24 substrate. The as-deposited microstructure characterizes fine cellular structure and the post weld heat treatment precipitates fine γ′particles. The room temperature tensile testing and 975℃, 196MPa stress rupture life testing indicate that ESD makes positively contribution to mechanical performance of repaired specimens. Based on these results, ESD has the potential as an effective alternative to repair of damage and defects in superalloy components, but more efforts should be made before it can be applied in engineering repair.

Mechanism of Building-Up Deposited Layer during Electro-Spark Deposition

This paper studies the mechanism of formation of the deposit layer by (ESD) electro-spark deposition process. Inconel 738 substrates are coated with a deposited layer of NI6625 (Inconel 625). Selections of these two alloys have been done because they had wide applications and importance in the industry especially in gas turban blades in inland stations and in aircraft engines. ESD is suggested because it has a low input heat process which eliminates the effect of HAZ in these Ni-superfluous due to their sustainability to micro-cracks. The coating contains many deposited sub-layers coming from evaporated and melted micro-regions as a result of locally high heat generated by discharging a series of capacitors charged and discharged in a controlled manner between electrode and substrate material. The maximum deposition rates at the beginning of the process and decreases until been in a steady state condition due to the nature of the resultant morphology of the created surface.

High-frequency electropulse deposition of microcrystallized MGH754 ODS alloy coatings

A simple but more efficient technique—high-frequency electropulse deposition—was developed to produce microcrystallized MGH754 ODS alloy coatings on the 1Cr18Ni9Ti stainless steel substrate. The coating has a very fine grain size of 30–300 nm and metallurgical bonding with the substrate. Isothermal oxidation in air at 1 000°C for 100 h shows that micro-crystallisation and dispersed oxide particles promote the selective oxidation of Cr greatly to form a protective and continuous Cr2O3 scale and also improve the scale spallation resistance dramatically, thus increasing the oxidation resistance of 1Cr18Ni9Ti.

High-frequency magnetic characteristics of Fe-Co-based nanocrystalline alloy films

Magnetically soft Fe-Co-based nanocrystalline alloy films were produced by two preparation methods:One using a new energetic cluster deposition technique and another using a conventional magnetron sputtering technique.Their structural,static magnetic properties and high-frequency magnetic characteristics were investigated.In the energetic cluster deposition method,by applying a high-bias voltage to a substrate,positively charged clusters in a cluster beam were accelerated electrically and deposited onto a negatively biased substrate together with neutral clusters from the same cluster source,to form a high-density Fe-Co alloy cluster-assembled film with good high-frequency magnetic characteristics.In the conventional magnetron sputtering method,only by rotating substrate holder and without applying a static inducing magnetic field on the substrates,we produced Fe-Co-based nanocrystalline alloy films with a remarkable in-plane uniaxial magnetic anisotropy and a good soft magnetic property.The obtained Fe-Co-O,Fe-Co-Ti-N,and Fe-Co-Cr-N films all revealed a high real permeability exceeding 500 at a frequency up to 1.2 GHz.This makes Fe-Co-based nanocrystalline alloy films potential candidates as soft magnetic thin film materials for the high-frequency applications.

Preparation and High Temperature Oxidation Properties of Micro-crystalline MGH754 ODS Alloy Coatings

A special coating technique, electro-spark deposition (ESD), was developed to produce micro-crystalline ODS MGH754 alloy coatings on a commercial 1Cr18Ni9Ti stainless steel and a cast Ni20Cr alloy substrates. The coatings have a very fine grain structure and metallurgical bonding with the substrates. The isothermal oxidation tests at 1000 degreesC in air showed that the micro-crystalline ODS alloy coatings had a much reduced oxidation rate and improved scale spallation resistance compared with the uncoated alloys. The selective oxidation of Cr was greatly promoted to form protective and continuous Cr2O3 scales on the alloy surface. Micro-crystallization and oxide dispersions have synergistic effects on the improvement of oxidation resistance. The beneficial effects were discussed based on the experimental results.

Hybrid Method for the Formation of Biocomposites on the Surface of Stainless Steel Implants

This study reports a hybrid method which allows the formation of biocomposites on stainless steel implants. The main idea of the method is to create multilayer coatings consisting of titanium primer layer and a microarc calcium-phosphate coating. The titanium layer is deposited from plasma of continuous vacuum-arc discharge, and calcium-phosphate coating is formed by the microarc oxidation technique. The purpose of the hybrid method is to combine the properties of good strength stainless steel with high bioactivity of calcium-phosphate coating. This paper describes the chemical composition, morphology characteristics, adhesion and the ability of the formed biocomposites to stimulate the processes of osteoinduction. It is expedient to use such biocomposites for implants which carry heavy loads and are intended for long-term use, e.g. total knee endoprosthesis.