Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve th...Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve their quality due to joint action of superficial effects and electromagnetic forces.For all magnetic materials is nonlinear decrease in heating power depending on frequency of HF.Installed the optimal parameters of HF heating for soldering electronics modules by inductor with open-ended magnetic conductor.展开更多
Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature dis...Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature distribution in the induction brazing model. The in?uences of induction brazing parameters on the residual stresses of polycrystalline CBN abrasive grits have been analyzed, including the embedding depth, grit side length, etc. Results obtained show that the tensile stress with a 40% embedding depth is 292 MPa, which is the minimum on the bonding interface compared with other embedding depths. Meanwhile, the maximum tensile stress is 575 MPa, with an increase of 59% compared with that of a grit side length of 50 mm. Finally, the simulation results of the brazing residual stress of polycrystalline CBN abrasive grits have been con?rmed valid based on the residual stress measurement of the brazed monocrystalline CBN grit.展开更多
A self-consistent model of high-frequency electrodeless lamps with internM coils is developed. Radial distributions of the plasma parameters are obtained. Mercury lines with wavelength of 435.8 nm and 365 nm are measu...A self-consistent model of high-frequency electrodeless lamps with internM coils is developed. Radial distributions of the plasma parameters are obtained. Mercury lines with wavelength of 435.8 nm and 365 nm are measured to testify the model. Based on the model, the population of resonance state 63p1 of mercury in dependence on the argon pressure and driving frequency is calculated. It is shown that the population of 63p1 of mercury is larger when the argon pressure is between 26.6 Pa and 53.2 Pa. Meanwhile the driving frequency has little influence on the population of 63P1.展开更多
For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted...For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted into cylindrical clay,the increase in temperature(Δ7)was 31.2℃ for the specimen with a 1.5 mm diameter,while the 1.0mm diameter specimen exhibited a ΔT value of 15.7℃ after the induction time of 1200s.The ΔT exhibited a high value of 57.9℃ during the simultaneous insertion of 3 1.5mm diameter specimens.In the computer simulation images, the relatively lower magnetic flux density and concurrent neghgibly low current density were observed from the surface to the internal regions,being different from the behavior of a ferromagnetic Ni-rod with the same size.展开更多
The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF...The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF modeling method,which has the merits of high accuracy,good versatility,and simple parameterization,is proposed.The proposed model of the induction motor consists of a three-phase equivalent circuit with eighteen circuit elements per phase to ensure model accuracy.The per phase circuit structure is symmetric concerning its phase-start and phase-end points.This symmetry enables the proposed model to be applicable for both star-and delta-connected induction motors without having to recalculate the circuit element values when changing the motor connection from star to delta and vice versa.Motor physics knowledge,namely per-phase impedances,are used in the artificial neural network to obtain the values of the circuit elements.The parameterization can be easily implemented within a few minutes using a common personal computer(PC).Case studies verify the effectiveness of the proposed HF modeling method.展开更多
According to the notice of the Office of Planned, Safe and Effective Use of Electricity (short as OPSEUE), all non-industrial consumers, such as hotels, shopping centers, are asked to use energy saving lamps instead o...According to the notice of the Office of Planned, Safe and Effective Use of Electricity (short as OPSEUE), all non-industrial consumers, such as hotels, shopping centers, are asked to use energy saving lamps instead of incandescent lamp and to eliminate inductive ballasts within the coming 3 years.展开更多
In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride(PCBN)grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction he...In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride(PCBN)grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.展开更多
文摘Modeling and investigation of HF electromagnetic heating in induction devices with unclosed magnetic circuit has allowed to optimize heating speed in local zones of formation of soldering connections and to improve their quality due to joint action of superficial effects and electromagnetic forces.For all magnetic materials is nonlinear decrease in heating power depending on frequency of HF.Installed the optimal parameters of HF heating for soldering electronics modules by inductor with open-ended magnetic conductor.
基金supported by the National Natural Science Foundation of China(No.51775275)the Fundamental Research Funds for the Central Universities(No.NE2014103 and No.NZ2016107)
文摘Residual stresses produced in polycrystalline CBN abrasive grits during a high-frequency induction brazing process are calculated by using ?nite element analysis, with a consideration of the nonuniform temperature distribution in the induction brazing model. The in?uences of induction brazing parameters on the residual stresses of polycrystalline CBN abrasive grits have been analyzed, including the embedding depth, grit side length, etc. Results obtained show that the tensile stress with a 40% embedding depth is 292 MPa, which is the minimum on the bonding interface compared with other embedding depths. Meanwhile, the maximum tensile stress is 575 MPa, with an increase of 59% compared with that of a grit side length of 50 mm. Finally, the simulation results of the brazing residual stress of polycrystalline CBN abrasive grits have been con?rmed valid based on the residual stress measurement of the brazed monocrystalline CBN grit.
文摘A self-consistent model of high-frequency electrodeless lamps with internM coils is developed. Radial distributions of the plasma parameters are obtained. Mercury lines with wavelength of 435.8 nm and 365 nm are measured to testify the model. Based on the model, the population of resonance state 63p1 of mercury in dependence on the argon pressure and driving frequency is calculated. It is shown that the population of 63p1 of mercury is larger when the argon pressure is between 26.6 Pa and 53.2 Pa. Meanwhile the driving frequency has little influence on the population of 63P1.
基金Item Sponsored by a Grant-in-Aid from Ministry of Education,Science,Sports and Culture of Japan[No.23500559:Naohara T]
文摘For application as a novel ablation therapy of human cancer,the heating property of a needle-shaped Mg-ferrite prepared by a sintering technique was studied in a high-frequency induction field at 370 kHz.When inserted into cylindrical clay,the increase in temperature(Δ7)was 31.2℃ for the specimen with a 1.5 mm diameter,while the 1.0mm diameter specimen exhibited a ΔT value of 15.7℃ after the induction time of 1200s.The ΔT exhibited a high value of 57.9℃ during the simultaneous insertion of 3 1.5mm diameter specimens.In the computer simulation images, the relatively lower magnetic flux density and concurrent neghgibly low current density were observed from the surface to the internal regions,being different from the behavior of a ferromagnetic Ni-rod with the same size.
文摘The high-frequency(HF)modeling of induction motors plays a key role in predicting the motor terminal overvoltage and conducted emissions in a motor drive system.In this study,a physics informed neural network-based HF modeling method,which has the merits of high accuracy,good versatility,and simple parameterization,is proposed.The proposed model of the induction motor consists of a three-phase equivalent circuit with eighteen circuit elements per phase to ensure model accuracy.The per phase circuit structure is symmetric concerning its phase-start and phase-end points.This symmetry enables the proposed model to be applicable for both star-and delta-connected induction motors without having to recalculate the circuit element values when changing the motor connection from star to delta and vice versa.Motor physics knowledge,namely per-phase impedances,are used in the artificial neural network to obtain the values of the circuit elements.The parameterization can be easily implemented within a few minutes using a common personal computer(PC).Case studies verify the effectiveness of the proposed HF modeling method.
文摘According to the notice of the Office of Planned, Safe and Effective Use of Electricity (short as OPSEUE), all non-industrial consumers, such as hotels, shopping centers, are asked to use energy saving lamps instead of incandescent lamp and to eliminate inductive ballasts within the coming 3 years.
基金financially supported by the National Natural Science Foundation of China(Nos.51235004 and51375235)the Fundamental Research Funds for the Central Universities(No.NE2014103)the Funding for Outstanding Doctoral Dissertation in NUAA(No.BCXJ16-06)
文摘In order to prepare monolayer brazed superabrasive wheels, the polycrystalline cubic boron nitride(PCBN)grains were brazed to AISI 1045 steel matrix with Ag–Cu–Ti filler alloy using the high-frequency induction heating technique. The compressive strengths of brazed grains were measured. Morphology, chemical composition and phase component of the brazing resultant around PCBN grain were also characterized. The results show that the maximum compressive strength of brazed grains is obtained in the case of brazing temperature of 965 °C, which does not decrease the original grain strength. Strong joining between Ag–Cu–Ti alloy and PCBN grains is dependent on the brazing resultants,such as TiB_2, TiN and AlTi_3, the formation mechanism of which is also discussed. Under the given experimental conditions, the optimum heating parameters were determined to be current magnitude of 24 A and scanning speed of0.5 mm/s. Finally, the brazing-induced residual tensile stress, which has a great influence on the grain fracture behavior in grinding, was determined through finite element analysis.