The aim and scope of the present study were to determine the efficacy of UFFA in evaluating the workability,static and dynamic stabilization properties,retention period,and slump loss of SCC systems in their fresh sta...The aim and scope of the present study were to determine the efficacy of UFFA in evaluating the workability,static and dynamic stabilization properties,retention period,and slump loss of SCC systems in their fresh state,as well as their compressive strength at various ages.Microstructure(SEM and XRD)of blended SCC systems were studied.Also,the thermogravimetry behavior of blended SCC specimens were researched.According to the evaluated results,incorporating up to 20%UFFA into fresh concrete improved its performance due to its engineered fine particle size and spherical geometry,both of which contribute to the enhancement of characteristics.Blends of 25%and 30%of UFFA show effect on the water-binder ratio and chemical enhancer dosage,resulting in a loss of homogeneity in fresh SCC systems.The reduced particle size,increased amorphous content,and increased surface area all contribute to the pozzolanic reactivity of the early and later ages,resulting in denser packing and thus an increase in compressive strength.The experimental results indicate that UFFA enhances the properties of SCC in both its fresh and hardened states,which can be attributed to the particles’fineness and their relative effect on SCC.展开更多
The measures of steam curing and early-strengthening agents to promote the precast components to reach the target strength quickly can bring different degrees of damage to the concrete.Based on this,the new nanomateri...The measures of steam curing and early-strengthening agents to promote the precast components to reach the target strength quickly can bring different degrees of damage to the concrete.Based on this,the new nanomaterial CSH-the hydration product of cement effectively solves these measures’disadvantages,such as excessive energy consumption,thermal stress damage,and the introduction of external ions.In this paper,the effect of CSH on the early strength of precast fly ash concrete components was investigated in terms of setting time,workability,and mechanical properties and analyzed at the microscopic level using hydration temperature,XRD,and SEM.The results showed that under the same workability,CSH could significantly reduce the amount of admixture,shorten the final setting time,almost not affect the initial setting time,and accelerate the hydration of cement.At the optimum dose of 5%,the mechanical properties of the specimens were improved by more than 98%within 12 h of hydration,resulting in an earlier release time of 12 h and no risk of strength inversion later.The results of this paper give theoretical support to the behavior of precast components under steam-free curing.展开更多
The properties of polyurethane concrete containing a large amount of fly ash are investigated,and accordingly,a model is introduced to account for the influence of fly ash fineness,water ratio,and loss of ignition(LOI...The properties of polyurethane concrete containing a large amount of fly ash are investigated,and accordingly,a model is introduced to account for the influence of fly ash fineness,water ratio,and loss of ignition(LOI)on its mechanical performances.This research shows that,after optimization,the concrete has a compressive strength of 20.8 MPa,a flexural strength of 3.4 MPa,and a compressive modulus of elasticity of 19.2 GPa.The main factor influencing 28 and 90 d compressive strength is fly ash content,water-binder ratio,and early strength agent content.展开更多
To promote the production and application of artificial aggregates,save natural sand resources and protect the ecological environment,we evaluated the feasibility of using spherical porous functional aggregates(SPFAs)...To promote the production and application of artificial aggregates,save natural sand resources and protect the ecological environment,we evaluated the feasibility of using spherical porous functional aggregates(SPFAs) formed by basalt saw mud under autoclave curing in ordinary structural concrete.In our work,two types of prewetted functional aggregates were taken as replacements for natural aggregates with different volume substitution rates(0%,5%,10%,15%,20%,25%,and 30%) in the preparation of ordinary structural concrete with water-to-binder ratios(W/B) of 0.48 and 0.33.The effects of the functional aggregate properties and content,W/B,and curing age on the fluidity,density,mechanical properties and autogenous shrinkage of ordinary concrete were analyzed.The experimental results showed that the density of concrete declined at a rate of not more than 5%,and the 28 d compressive strength could reach 31.0-68.2 MPa.Low W/B,long curing age and high-quality functional aggregates were conducive to enhancing the mechanical properties of SPFAs concrete.Through the rolling effects,SPFAs can optimize the particle gradation of aggregate systems and improve the fluidity of concrete,and the water stored inside SPFAs provides an internal curing effect,which prolongs the cement hydration process and considerably reduces the autogenous shrinkage of concrete.SPFAs exhibits high strength and high density,as well as being more cost-effective and ecological,and is expected to be widely employed in ordinary structural concrete.展开更多
Geopolymer concrete emerges as a promising avenue for sustainable development and offers an effective solution to environmental problems.Its attributes as a non-toxic,low-carbon,and economical substitute for conventio...Geopolymer concrete emerges as a promising avenue for sustainable development and offers an effective solution to environmental problems.Its attributes as a non-toxic,low-carbon,and economical substitute for conventional cement concrete,coupled with its elevated compressive strength and reduced shrinkage properties,position it as a pivotal material for diverse applications spanning from architectural structures to transportation infrastructure.In this context,this study sets out the task of using machine learning(ML)algorithms to increase the accuracy and interpretability of predicting the compressive strength of geopolymer concrete in the civil engineering field.To achieve this goal,a new approach using convolutional neural networks(CNNs)has been adopted.This study focuses on creating a comprehensive dataset consisting of compositional and strength parameters of 162 geopolymer concrete mixes,all containing Class F fly ash.The selection of optimal input parameters is guided by two distinct criteria.The first criterion leverages insights garnered from previous research on the influence of individual features on compressive strength.The second criterion scrutinizes the impact of these features within the model’s predictive framework.Key to enhancing the CNN model’s performance is the meticulous determination of the optimal hyperparameters.Through a systematic trial-and-error process,the study ascertains the ideal number of epochs for data division and the optimal value of k for k-fold cross-validation—a technique vital to the model’s robustness.The model’s predictive prowess is rigorously assessed via a suite of performance metrics and comprehensive score analyses.Furthermore,the model’s adaptability is gauged by integrating a secondary dataset into its predictive framework,facilitating a comparative evaluation against conventional prediction methods.To unravel the intricacies of the CNN model’s learning trajectory,a loss plot is deployed to elucidate its learning rate.The study culminates in compelling findings that underscore the CNN model’s accurate prediction of geopolymer concrete compressive strength.To maximize the dataset’s potential,the application of bivariate plots unveils nuanced trends and interactions among variables,fortifying the consistency with earlier research.Evidenced by promising prediction accuracy,the study’s outcomes hold significant promise in guiding the development of innovative geopolymer concrete formulations,thereby reinforcing its role as an eco-conscious and robust construction material.The findings prove that the CNN model accurately estimated geopolymer concrete’s compressive strength.The results show that the prediction accuracy is promising and can be used for the development of new geopolymer concrete mixes.The outcomes not only underscore the significance of leveraging technology for sustainable construction practices but also pave the way for innovation and efficiency in the field of civil engineering.展开更多
The effects of fly ash on the compressive strength, pore size distribution and chloride-ion penetration of recycled aggregate concrete were investigated. Two series of concrete mb:tures were prepared. The concrete mi...The effects of fly ash on the compressive strength, pore size distribution and chloride-ion penetration of recycled aggregate concrete were investigated. Two series of concrete mb:tures were prepared. The concrete mixtures in series I had a water-to-binder ratio and a cement content of 0.55 and 410 kg/ m^3 , respectively. The concrete rnixtures in series II had a water-to-binder ratio and a cement content of 0.45 and 400 kg/ ml respectively. Recycled aggregate was ased as 20% , 50% , and 100% replacements of natural coarse aggregate in the concrete mixtures in both series. In cutdition, fly ash was used as 0% , 25% and 35% by weight replacements of cement. The results show that the compressive strengths of the concrete decreased as the recycled aggregate and the fly ash contents increased. The total porosity and average porosity diameter of the concrete increased us the recycled aggregate content increased. Furtherrruore , an increase in the recycled aggregate content decreased the resistance to chloride ion penetration. Nevertheless, the replacement of cement by 25% fly ush improved the resistance to chloride ion penetration and pore diameters and reduced the total porosity of the recycled aggregate concrete.展开更多
2D,3D chloride ion concentration at the edge and corner zones were systematically investigated for fly ash concretes made with different cement replacement percentage by fly ash (0%,10%,20%,40%,60%),water to binder ...2D,3D chloride ion concentration at the edge and corner zones were systematically investigated for fly ash concretes made with different cement replacement percentage by fly ash (0%,10%,20%,40%,60%),water to binder ratios (0.3,0.35,0.4),and curing ages (28 d,90 d).An interaction effect caused by 2D and 3D diffusion could obviously be observed through the comparison with 1D testing results.In order to quantify the interaction effect,2D and 3D diffusion interaction coefficients was proposed in this paper.Finally,the changes of 2D and 3D interaction coefficients with the change in the free chloride ion concentration were given.The above research provide an insight into chloride ion attack on the edge and corner reinforcing bars of concrete structures in the field of civil engineering.展开更多
It is necessary to pay more attention to the durability of concrete undergoing freeze-thaw cycles and seawater attack simultaneously.Investigated are the effects of water-binder ratio,fly ash(FA)contents and air-ent...It is necessary to pay more attention to the durability of concrete undergoing freeze-thaw cycles and seawater attack simultaneously.Investigated are the effects of water-binder ratio,fly ash(FA)contents and air-entraining agent on resistance to frost and chloride diffusion of marine concrete blended with FA in natural seawater.The results show that fly ash does not improve the frost resistance of concrete but can improve its resistance to chloride diffusion by addition of less than 30%.The resistance to frost and chloride diffusion of FA concrete can be improved with the decrease of water-binder ratio,and FA may improve both of them simultaneously only being mixed with air-entraining agent.A ratio(named as R)of the frost-resisting durability factor to chloride diffusion coefficient can be used to evaluate the durability of marine concrete.Scanning electron microscope(SEM)analyses are consistent with the evaluations by the value of R.展开更多
To decrease the cement and SF content of RPC by using ultra-fine fly ash (UFFA) and steel slag powder (SS), the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental...To decrease the cement and SF content of RPC by using ultra-fine fly ash (UFFA) and steel slag powder (SS), the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental results indicate that the utilization of UFFA and SS in RPC is feasible and has prominent mechanical performance. The microstructure analysis (SEM and TG-DTG-DSC) demonstrated that the excellent mechanical properties of RPC containing SS and UFFA were mainly attributed to the sequential hydration filling effect of the compound system.展开更多
To provide basic data for the reasonable mixing design of the alkali-activated (AA) foamed concrete as a thermal insulation material for a floor heating system, 9 concrete mixes with a targeted dry density less than 4...To provide basic data for the reasonable mixing design of the alkali-activated (AA) foamed concrete as a thermal insulation material for a floor heating system, 9 concrete mixes with a targeted dry density less than 400 kg/m3 were tested. Ground granulated blast-furnace slag (GGBS) as a source material was activated by the following two types of alkali activators: 10% Ca(OH)2 and 4% Mg(NO3)2, and 2.5% Ca(OH)2 and 6.5% Na2SiO3. The main test parameters were water-to-binder (W/B) ratio and the substitution level (RFA) of fly ash (FA) for GGBS. Test results revealed that the dry density of AA GGBS foamed concrete was independent of the W/B ratio an RFA, whereas the compressive strength increased with the decrease in W/B ratio and with the increase in RFA up to 15%, beyond which it decreased. With the increase in the W/B ratio, the amount of macro capillaries and artificial air pores increased, which resulted in the decrease of compressive strength. The magnitude of the environmental loads of the AA GGBS foamed concrete is independent of the W/B ratio and RFA. The largest reduction percentage was found in the photochemical oxidation potential, being more than 99%. The reduction percentage was 87% - 93% for the global warming potential, 81% - 84% for abiotic depletion, 79% - 84% for acidification potential, 77% - 85% for eutrophication potential, and 73% - 83% for human toxicity potential. Ultimately, this study proved that the developed AA GGBS foamed concrete has a considerable promise as a sustainable construction material for nonstructural element.展开更多
This study was conducted to evaluate the sensitivity of compressive strength,water permeability and electrical resistance of near-surface layer concrete with different fly ash contents to curing conditions.It is shown...This study was conducted to evaluate the sensitivity of compressive strength,water permeability and electrical resistance of near-surface layer concrete with different fly ash contents to curing conditions.It is shown that the sensitivity to curing condition and fly ash content descends in the following order:difference between internal and surface resistivity (ρ) at 28 days,water permeability and compressive strength;both of longer duration of moist curing and use of fly ash in concrete enhanced the water penetration resistance.It is indicated that the resistivity difference ρ at 28 days can reflect accurately the curing history of fly ash concrete regardless of mix proportions;and use of fly ash in concrete requires longer moist curing duration.展开更多
The effect of fly ash and early strength agent on resistance of concrete to the cyclic sulfate environment was studied.Concrete specimens made with ordinary portland cement or ordinary portland cement incorporating fl...The effect of fly ash and early strength agent on resistance of concrete to the cyclic sulfate environment was studied.Concrete specimens made with ordinary portland cement or ordinary portland cement incorporating fly ash with the replacement of 10% or 20%,or 1% early strength agent and fly ash with the replacement of 20%,were made and subjected to 250 cycles of exposure to the cyclic sulfate environment.Concrete properties including loss of mass,chloride ion diffusion coefficient,compressive strength and flexural strength were measured.Microstructure and chemical component of samples were determined by means of X-ray diffraction,scanning electron microscopy and energy dispersive spectroscopy.The experimental results indicated that effect of fly ash on the cyclic sulfate resistance of concretes was mostly dependent on the amount of fly ash.Early strength agent improved performances of concrete with 20% fly ash exposed to cyclic sulfate environment.展开更多
Cellular lightweight concrete (CLC) with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement (OPC), fly ash (FA), or natural zeolite (NZ), and its compressi...Cellular lightweight concrete (CLC) with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement (OPC), fly ash (FA), or natural zeolite (NZ), and its compressive strength, setting time, water absorption, and microstructure of were tested. High-calcium FA and NZ with the median particle sizes of 14.52 and 7.72 μm, respectively, were used to partially replace OPC at 0, 10wt%, 20wt%, and 30wt% of the binder (OPC and pozzolan admixture). A water-to-binder mass ratio (W/B) of 0.5 was used for all mixes. The testing results indicated that CLC containing 10wt% NZ had the highest compressive strength. The replacement of OPC with NZ decreased the total porosity and air void size but increased the capillary porosity of the CLC. The incorporation of a suitable amount of NZ decreased the setting time, total porosity, and pore size of the paste compared with the findings with the same amount of FA. The total porosity and cumulative pore volume decreased, whereas the gel and capillary pores increased as a result of adding both pozzolans at all replacement levels. The water absorption increased as the capillary porosity increased; this effect depended on the volume of air entrained and the type or amount of pozzolan.展开更多
Pervious concrete is recommended,which is of great benefit to the ecological environment and human living environment.In this paper,the influences of five water-cement ratios and four fly ash contents to replace the c...Pervious concrete is recommended,which is of great benefit to the ecological environment and human living environment.In this paper,the influences of five water-cement ratios and four fly ash contents to replace the cement by mass with a water-cement ratio of 0.30 on the properties of Recycled Aggregate Pervious Concrete(RAPC)were studied.Following this,based on the Grey relational-Technique for Order Preference by Similarity to an Ideal Solution(TOPSIS)optimization method,the strength,permeability,abrasion loss rate,and material costs of RAPC were adopted as evaluation indices to establish a mix proportion optimization model.The results show that the increase of water-cement ratio and fly ash replacement level of RAPC leads to decreased compres-sive strength while an increase in the permeability and abrasion loss rate.According to test results based on the optimal model 0.30 was identified as the best mix proportion.In addition,ecological-economic analysis of RAPC raw materials was carried out by comparing different natural aggregates.The results of EE(embodied energy)and ECO 2e(embodied CO_(2) emission)pointed out that the combination of recycled aggregate and fly ash leads to sig-nificant ecological and economic benefits.展开更多
The issue of concrete carbonation has gained importance in recent years due to the increase use in supplementary cementing materials (SCMs) in concrete mixtures. While there is general agreement that concrete carbonat...The issue of concrete carbonation has gained importance in recent years due to the increase use in supplementary cementing materials (SCMs) in concrete mixtures. While there is general agreement that concrete carbonation progresses at maximum at a relative humidity of about 60%, the rate may differ in the case of cements blended with SCMs, especially with high-volume fly ash replacements. In this study, the effect of high-volume fly ash concrete exposed to low ambient relative humidity (RH) conditions (57%) and accelerated carbonation (4% CO2) is investigated. Twenty-three concrete mixtures were produced varying in cementitious contents (310, 340, 370, and 400 kg/m3), water-to-cementitious materials ratio (0.45 and 0.50), and fly ash content (0%, 15%, 30%, and 50%) using a low and high-calcium fly ash. The specimens were allowed 1 and 7 days of moist curing and monitored for their carbonation rate and depth through phenolphthalein measurements up to 105 days of exposure. The accelerated carbonation test results indicated that increasing the addition of fly ash also led to increasing the depth of carbonation. Mixtures incorporating high-calcium fly ash were also observed to be more resistant against carbonation than low-calcium fly ash due to the higher calcium oxide (CaO) content. However, mixtures incorporating high-volume additions (50%) specimens were fully carbonated regardless of the type of fly ash used. It was evident that the increase in the duration of moist curing from 1 day to 7 days had a positive effect, reducing the carbonation depth for both plain and blended fly ash concrete mixes, however, this effect was minimal in high-volume fly ash mixtures. The results demonstrated that the water-to-cementitious ratio (W/CM) had a more dramatic impact on carbonation resistance than the curing age for mixtures incorporating 30% or less fly ash replacement, whereas those mixtures incorporating 50% showed minor differences regardless of curing age or W/CM. Based on the compressive strength results, carbonation depth appeared to decrease with increase in compressive strength, but this correlation was not significant.展开更多
Solid waste disposal is an alarming problem in most African countries. Plastic wastes like Polyethylene Terephthalate (PET) bottles and powdered wastes like fly ash are severely persisting environmental hazards. They ...Solid waste disposal is an alarming problem in most African countries. Plastic wastes like Polyethylene Terephthalate (PET) bottles and powdered wastes like fly ash are severely persisting environmental hazards. They are brutally polluting the water bodies, landfills, as well as the atmosphere. The construction industry has been working towards improving concrete quality by developing alternative methods like partial cement replacement with different pozzolanic elements as well as using waste fibrous materials. Fly ash and PET bottle fibres are two common waste materials that can be used. This article is a part of a research that studied the combined effects of the addition of PET bottle fibres and fly ash (as a partial cement replacement) on the structural performance of concrete. From a purely engineering point of view, the research results indicate that the utilization and incorporation of PET and fly ash wastes in the construction industry are a viable solution to make concrete quality better. This article presents, beyond the engineering properties and experimental works, the economic and environmental advantages of the addition of these waste materials to the conventional concrete mixture. The addition of PET bottle fibres and fly ash resulted in positive cost implications providing a production cost reduction of 19% over the conventional concrete mixture. The removal of these materials from the environment also showed reduction of the emission of toxic elements to landfills and water bodies that put human, animal and plant lives in danger.展开更多
This paper investigates the experimental results on the effect of nano silica fume on compressive strength development of concretes containing high volume fly ash (HVFA). The effect of various silica fumes contents su...This paper investigates the experimental results on the effect of nano silica fume on compressive strength development of concretes containing high volume fly ash (HVFA). The effect of various silica fumes contents such as 1%, 2% & 3% (wt. %) as partial replacement of cement on the compressive strength of cements is evaluated in the first part. The nano silica fume content which exhibits the highest compressive strength above is used in high volume fly ash concretes containing 30% and 50% class F fly ash. The results show that among three different silica fumes contents, the addition of 1% increases the compressive strength of concretes. The addition of 1% silica fume also increases the early age and 28 days compressive strengths of HVFA concretes.展开更多
The enhancement effects of GH admixture on the early strengths of fly ash concrete and mortar were studied, and the mechanism was analyzed by X-ray diffraction (XRD) and scanning electro microscope (SEM). Experime...The enhancement effects of GH admixture on the early strengths of fly ash concrete and mortar were studied, and the mechanism was analyzed by X-ray diffraction (XRD) and scanning electro microscope (SEM). Experimental results show that, by the incorporation of GH admixture, both of cement hydration and pozzolanic reaction of fly ash are accelerated, the strengths of fly ash concrete and mortar are enhanced noticeably, especially the early strength. With a mixture design of 200 kg/m^3 OPC (Ordinary Portland Cement ), 200 kg/m^3 fly ash and 50 kg/m^3 GH admixture, the strength of concrete at 1 d, 3 d and 28 d reaches 25 MPa, 50 MPa and 70 MPa respectively.展开更多
According to the life cycle assessment and the environmental design method of industry prnduction, a quantitative assessment model for the embodied environmetal impact of concrete with or without fly ash was proposed....According to the life cycle assessment and the environmental design method of industry prnduction, a quantitative assessment model for the embodied environmetal impact of concrete with or without fly ash was proposed. The environmental burden impact indicator ( EBII ), the resources depletion impact indicator (RDII), and the environmental impact comprehensive indicator (EICI) are defined. The specific environmental impact values of different grade concretes with or wittout fly ash were presented. In the embodied process of concrete with or without fly ash, the key potential environmental impact categories are global warming and dust endsskin, and it is an effective way for reducing the embndied environmental impact of concrete to mix fly ash and lower grade cenwat . The method presented in this paper makes it possible to quantitatively assess the embodied environmental impact of concrete with or without .fly ash. The results calculated in this paper can be used to quantitatively assess the life cycle environmental impact of construction materials and buildings.展开更多
The compressive strength,hydration products and microstructure of concrete with calcium-enriched fly ash(CEFA) at different temperature were investigated.The result indicates that the hydration products age of 7 d at-...The compressive strength,hydration products and microstructure of concrete with calcium-enriched fly ash(CEFA) at different temperature were investigated.The result indicates that the hydration products age of 7 d at-15 ℃ are mainly ettringite and C-S-H,and fly ash particles remain original state.Standard curing was adapted after 7 d curing at-15 ℃.At the age of 35 d,C-S-H was found on the surface of fly ash particles.The hydration product of CEFA is mainly C-S-H gel,which can densify the microstructure of concrete.展开更多
文摘The aim and scope of the present study were to determine the efficacy of UFFA in evaluating the workability,static and dynamic stabilization properties,retention period,and slump loss of SCC systems in their fresh state,as well as their compressive strength at various ages.Microstructure(SEM and XRD)of blended SCC systems were studied.Also,the thermogravimetry behavior of blended SCC specimens were researched.According to the evaluated results,incorporating up to 20%UFFA into fresh concrete improved its performance due to its engineered fine particle size and spherical geometry,both of which contribute to the enhancement of characteristics.Blends of 25%and 30%of UFFA show effect on the water-binder ratio and chemical enhancer dosage,resulting in a loss of homogeneity in fresh SCC systems.The reduced particle size,increased amorphous content,and increased surface area all contribute to the pozzolanic reactivity of the early and later ages,resulting in denser packing and thus an increase in compressive strength.The experimental results indicate that UFFA enhances the properties of SCC in both its fresh and hardened states,which can be attributed to the particles’fineness and their relative effect on SCC.
文摘The measures of steam curing and early-strengthening agents to promote the precast components to reach the target strength quickly can bring different degrees of damage to the concrete.Based on this,the new nanomaterial CSH-the hydration product of cement effectively solves these measures’disadvantages,such as excessive energy consumption,thermal stress damage,and the introduction of external ions.In this paper,the effect of CSH on the early strength of precast fly ash concrete components was investigated in terms of setting time,workability,and mechanical properties and analyzed at the microscopic level using hydration temperature,XRD,and SEM.The results showed that under the same workability,CSH could significantly reduce the amount of admixture,shorten the final setting time,almost not affect the initial setting time,and accelerate the hydration of cement.At the optimum dose of 5%,the mechanical properties of the specimens were improved by more than 98%within 12 h of hydration,resulting in an earlier release time of 12 h and no risk of strength inversion later.The results of this paper give theoretical support to the behavior of precast components under steam-free curing.
基金The Second Batch of Industry-University Cooperative Education Projects in 2021(202102113047)Science and Technology Project of Hubei Construction Department[2019(672)].
文摘The properties of polyurethane concrete containing a large amount of fly ash are investigated,and accordingly,a model is introduced to account for the influence of fly ash fineness,water ratio,and loss of ignition(LOI)on its mechanical performances.This research shows that,after optimization,the concrete has a compressive strength of 20.8 MPa,a flexural strength of 3.4 MPa,and a compressive modulus of elasticity of 19.2 GPa.The main factor influencing 28 and 90 d compressive strength is fly ash content,water-binder ratio,and early strength agent content.
基金Funded by the National Natural Science Foundation of China(No.52378213)the Technology Development Project(No.20201902977180010) of CABR Technology Co.,Ltd。
文摘To promote the production and application of artificial aggregates,save natural sand resources and protect the ecological environment,we evaluated the feasibility of using spherical porous functional aggregates(SPFAs) formed by basalt saw mud under autoclave curing in ordinary structural concrete.In our work,two types of prewetted functional aggregates were taken as replacements for natural aggregates with different volume substitution rates(0%,5%,10%,15%,20%,25%,and 30%) in the preparation of ordinary structural concrete with water-to-binder ratios(W/B) of 0.48 and 0.33.The effects of the functional aggregate properties and content,W/B,and curing age on the fluidity,density,mechanical properties and autogenous shrinkage of ordinary concrete were analyzed.The experimental results showed that the density of concrete declined at a rate of not more than 5%,and the 28 d compressive strength could reach 31.0-68.2 MPa.Low W/B,long curing age and high-quality functional aggregates were conducive to enhancing the mechanical properties of SPFAs concrete.Through the rolling effects,SPFAs can optimize the particle gradation of aggregate systems and improve the fluidity of concrete,and the water stored inside SPFAs provides an internal curing effect,which prolongs the cement hydration process and considerably reduces the autogenous shrinkage of concrete.SPFAs exhibits high strength and high density,as well as being more cost-effective and ecological,and is expected to be widely employed in ordinary structural concrete.
基金funded by the Researchers Supporting Program at King Saud University(RSPD2023R809).
文摘Geopolymer concrete emerges as a promising avenue for sustainable development and offers an effective solution to environmental problems.Its attributes as a non-toxic,low-carbon,and economical substitute for conventional cement concrete,coupled with its elevated compressive strength and reduced shrinkage properties,position it as a pivotal material for diverse applications spanning from architectural structures to transportation infrastructure.In this context,this study sets out the task of using machine learning(ML)algorithms to increase the accuracy and interpretability of predicting the compressive strength of geopolymer concrete in the civil engineering field.To achieve this goal,a new approach using convolutional neural networks(CNNs)has been adopted.This study focuses on creating a comprehensive dataset consisting of compositional and strength parameters of 162 geopolymer concrete mixes,all containing Class F fly ash.The selection of optimal input parameters is guided by two distinct criteria.The first criterion leverages insights garnered from previous research on the influence of individual features on compressive strength.The second criterion scrutinizes the impact of these features within the model’s predictive framework.Key to enhancing the CNN model’s performance is the meticulous determination of the optimal hyperparameters.Through a systematic trial-and-error process,the study ascertains the ideal number of epochs for data division and the optimal value of k for k-fold cross-validation—a technique vital to the model’s robustness.The model’s predictive prowess is rigorously assessed via a suite of performance metrics and comprehensive score analyses.Furthermore,the model’s adaptability is gauged by integrating a secondary dataset into its predictive framework,facilitating a comparative evaluation against conventional prediction methods.To unravel the intricacies of the CNN model’s learning trajectory,a loss plot is deployed to elucidate its learning rate.The study culminates in compelling findings that underscore the CNN model’s accurate prediction of geopolymer concrete compressive strength.To maximize the dataset’s potential,the application of bivariate plots unveils nuanced trends and interactions among variables,fortifying the consistency with earlier research.Evidenced by promising prediction accuracy,the study’s outcomes hold significant promise in guiding the development of innovative geopolymer concrete formulations,thereby reinforcing its role as an eco-conscious and robust construction material.The findings prove that the CNN model accurately estimated geopolymer concrete’s compressive strength.The results show that the prediction accuracy is promising and can be used for the development of new geopolymer concrete mixes.The outcomes not only underscore the significance of leveraging technology for sustainable construction practices but also pave the way for innovation and efficiency in the field of civil engineering.
基金Funded by the Environment and Conservation Fund, the WooWheelock Green Fund andthe Hong Kong Polytechnic University
文摘The effects of fly ash on the compressive strength, pore size distribution and chloride-ion penetration of recycled aggregate concrete were investigated. Two series of concrete mb:tures were prepared. The concrete mixtures in series I had a water-to-binder ratio and a cement content of 0.55 and 410 kg/ m^3 , respectively. The concrete rnixtures in series II had a water-to-binder ratio and a cement content of 0.45 and 400 kg/ ml respectively. Recycled aggregate was ased as 20% , 50% , and 100% replacements of natural coarse aggregate in the concrete mixtures in both series. In cutdition, fly ash was used as 0% , 25% and 35% by weight replacements of cement. The results show that the compressive strengths of the concrete decreased as the recycled aggregate and the fly ash contents increased. The total porosity and average porosity diameter of the concrete increased us the recycled aggregate content increased. Furtherrruore , an increase in the recycled aggregate content decreased the resistance to chloride ion penetration. Nevertheless, the replacement of cement by 25% fly ush improved the resistance to chloride ion penetration and pore diameters and reduced the total porosity of the recycled aggregate concrete.
基金Funded by National Natural Science Fundation of China (No.51178106)Open Program from Guangxi Key Laboratory of Disaster Prevention and Reduction (No.2008TMKF009)+1 种基金973 Program (No.2009CB623200)Program for New Century Excellent Talentsin University
文摘2D,3D chloride ion concentration at the edge and corner zones were systematically investigated for fly ash concretes made with different cement replacement percentage by fly ash (0%,10%,20%,40%,60%),water to binder ratios (0.3,0.35,0.4),and curing ages (28 d,90 d).An interaction effect caused by 2D and 3D diffusion could obviously be observed through the comparison with 1D testing results.In order to quantify the interaction effect,2D and 3D diffusion interaction coefficients was proposed in this paper.Finally,the changes of 2D and 3D interaction coefficients with the change in the free chloride ion concentration were given.The above research provide an insight into chloride ion attack on the edge and corner reinforcing bars of concrete structures in the field of civil engineering.
基金supported by the National Natural Science Foundation of China(Grant No.50572127)
文摘It is necessary to pay more attention to the durability of concrete undergoing freeze-thaw cycles and seawater attack simultaneously.Investigated are the effects of water-binder ratio,fly ash(FA)contents and air-entraining agent on resistance to frost and chloride diffusion of marine concrete blended with FA in natural seawater.The results show that fly ash does not improve the frost resistance of concrete but can improve its resistance to chloride diffusion by addition of less than 30%.The resistance to frost and chloride diffusion of FA concrete can be improved with the decrease of water-binder ratio,and FA may improve both of them simultaneously only being mixed with air-entraining agent.A ratio(named as R)of the frost-resisting durability factor to chloride diffusion coefficient can be used to evaluate the durability of marine concrete.Scanning electron microscope(SEM)analyses are consistent with the evaluations by the value of R.
基金Funded by the Guide Project in National Science & Technology Pillar Program during the 10th Five-Year Plan Period (2003BA652C)
文摘To decrease the cement and SF content of RPC by using ultra-fine fly ash (UFFA) and steel slag powder (SS), the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental results indicate that the utilization of UFFA and SS in RPC is feasible and has prominent mechanical performance. The microstructure analysis (SEM and TG-DTG-DSC) demonstrated that the excellent mechanical properties of RPC containing SS and UFFA were mainly attributed to the sequential hydration filling effect of the compound system.
文摘To provide basic data for the reasonable mixing design of the alkali-activated (AA) foamed concrete as a thermal insulation material for a floor heating system, 9 concrete mixes with a targeted dry density less than 400 kg/m3 were tested. Ground granulated blast-furnace slag (GGBS) as a source material was activated by the following two types of alkali activators: 10% Ca(OH)2 and 4% Mg(NO3)2, and 2.5% Ca(OH)2 and 6.5% Na2SiO3. The main test parameters were water-to-binder (W/B) ratio and the substitution level (RFA) of fly ash (FA) for GGBS. Test results revealed that the dry density of AA GGBS foamed concrete was independent of the W/B ratio an RFA, whereas the compressive strength increased with the decrease in W/B ratio and with the increase in RFA up to 15%, beyond which it decreased. With the increase in the W/B ratio, the amount of macro capillaries and artificial air pores increased, which resulted in the decrease of compressive strength. The magnitude of the environmental loads of the AA GGBS foamed concrete is independent of the W/B ratio and RFA. The largest reduction percentage was found in the photochemical oxidation potential, being more than 99%. The reduction percentage was 87% - 93% for the global warming potential, 81% - 84% for abiotic depletion, 79% - 84% for acidification potential, 77% - 85% for eutrophication potential, and 73% - 83% for human toxicity potential. Ultimately, this study proved that the developed AA GGBS foamed concrete has a considerable promise as a sustainable construction material for nonstructural element.
基金Funded by the National Natural Science Foundation of China(No.51002193)
文摘This study was conducted to evaluate the sensitivity of compressive strength,water permeability and electrical resistance of near-surface layer concrete with different fly ash contents to curing conditions.It is shown that the sensitivity to curing condition and fly ash content descends in the following order:difference between internal and surface resistivity (ρ) at 28 days,water permeability and compressive strength;both of longer duration of moist curing and use of fly ash in concrete enhanced the water penetration resistance.It is indicated that the resistivity difference ρ at 28 days can reflect accurately the curing history of fly ash concrete regardless of mix proportions;and use of fly ash in concrete requires longer moist curing duration.
基金Funded by the Western Communication Construction Science and Technology Item (No. 200631822302-08)
文摘The effect of fly ash and early strength agent on resistance of concrete to the cyclic sulfate environment was studied.Concrete specimens made with ordinary portland cement or ordinary portland cement incorporating fly ash with the replacement of 10% or 20%,or 1% early strength agent and fly ash with the replacement of 20%,were made and subjected to 250 cycles of exposure to the cyclic sulfate environment.Concrete properties including loss of mass,chloride ion diffusion coefficient,compressive strength and flexural strength were measured.Microstructure and chemical component of samples were determined by means of X-ray diffraction,scanning electron microscopy and energy dispersive spectroscopy.The experimental results indicated that effect of fly ash on the cyclic sulfate resistance of concretes was mostly dependent on the amount of fly ash.Early strength agent improved performances of concrete with 20% fly ash exposed to cyclic sulfate environment.
基金the financial support of the Rajamangala University of Technology Isan, Thailand,for a grant originating from the Strategic Scholarships for Frontier Research Network, which supports the Joint Ph.D. Program and Thai doctoral degreethe Thailand Research Fund (TRF) for financial support originating from the TRF Senior Research Scholarship (No.RTA5480004)the TRF New Researcher Scholarship (No.MRG5280178)
文摘Cellular lightweight concrete (CLC) with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement (OPC), fly ash (FA), or natural zeolite (NZ), and its compressive strength, setting time, water absorption, and microstructure of were tested. High-calcium FA and NZ with the median particle sizes of 14.52 and 7.72 μm, respectively, were used to partially replace OPC at 0, 10wt%, 20wt%, and 30wt% of the binder (OPC and pozzolan admixture). A water-to-binder mass ratio (W/B) of 0.5 was used for all mixes. The testing results indicated that CLC containing 10wt% NZ had the highest compressive strength. The replacement of OPC with NZ decreased the total porosity and air void size but increased the capillary porosity of the CLC. The incorporation of a suitable amount of NZ decreased the setting time, total porosity, and pore size of the paste compared with the findings with the same amount of FA. The total porosity and cumulative pore volume decreased, whereas the gel and capillary pores increased as a result of adding both pozzolans at all replacement levels. The water absorption increased as the capillary porosity increased; this effect depended on the volume of air entrained and the type or amount of pozzolan.
基金This work was supported by the National Natural Science Foundation of China(No.52009045)National Key Research and Development Program of China(No.2018YFC0406902).
文摘Pervious concrete is recommended,which is of great benefit to the ecological environment and human living environment.In this paper,the influences of five water-cement ratios and four fly ash contents to replace the cement by mass with a water-cement ratio of 0.30 on the properties of Recycled Aggregate Pervious Concrete(RAPC)were studied.Following this,based on the Grey relational-Technique for Order Preference by Similarity to an Ideal Solution(TOPSIS)optimization method,the strength,permeability,abrasion loss rate,and material costs of RAPC were adopted as evaluation indices to establish a mix proportion optimization model.The results show that the increase of water-cement ratio and fly ash replacement level of RAPC leads to decreased compres-sive strength while an increase in the permeability and abrasion loss rate.According to test results based on the optimal model 0.30 was identified as the best mix proportion.In addition,ecological-economic analysis of RAPC raw materials was carried out by comparing different natural aggregates.The results of EE(embodied energy)and ECO 2e(embodied CO_(2) emission)pointed out that the combination of recycled aggregate and fly ash leads to sig-nificant ecological and economic benefits.
文摘The issue of concrete carbonation has gained importance in recent years due to the increase use in supplementary cementing materials (SCMs) in concrete mixtures. While there is general agreement that concrete carbonation progresses at maximum at a relative humidity of about 60%, the rate may differ in the case of cements blended with SCMs, especially with high-volume fly ash replacements. In this study, the effect of high-volume fly ash concrete exposed to low ambient relative humidity (RH) conditions (57%) and accelerated carbonation (4% CO2) is investigated. Twenty-three concrete mixtures were produced varying in cementitious contents (310, 340, 370, and 400 kg/m3), water-to-cementitious materials ratio (0.45 and 0.50), and fly ash content (0%, 15%, 30%, and 50%) using a low and high-calcium fly ash. The specimens were allowed 1 and 7 days of moist curing and monitored for their carbonation rate and depth through phenolphthalein measurements up to 105 days of exposure. The accelerated carbonation test results indicated that increasing the addition of fly ash also led to increasing the depth of carbonation. Mixtures incorporating high-calcium fly ash were also observed to be more resistant against carbonation than low-calcium fly ash due to the higher calcium oxide (CaO) content. However, mixtures incorporating high-volume additions (50%) specimens were fully carbonated regardless of the type of fly ash used. It was evident that the increase in the duration of moist curing from 1 day to 7 days had a positive effect, reducing the carbonation depth for both plain and blended fly ash concrete mixes, however, this effect was minimal in high-volume fly ash mixtures. The results demonstrated that the water-to-cementitious ratio (W/CM) had a more dramatic impact on carbonation resistance than the curing age for mixtures incorporating 30% or less fly ash replacement, whereas those mixtures incorporating 50% showed minor differences regardless of curing age or W/CM. Based on the compressive strength results, carbonation depth appeared to decrease with increase in compressive strength, but this correlation was not significant.
文摘Solid waste disposal is an alarming problem in most African countries. Plastic wastes like Polyethylene Terephthalate (PET) bottles and powdered wastes like fly ash are severely persisting environmental hazards. They are brutally polluting the water bodies, landfills, as well as the atmosphere. The construction industry has been working towards improving concrete quality by developing alternative methods like partial cement replacement with different pozzolanic elements as well as using waste fibrous materials. Fly ash and PET bottle fibres are two common waste materials that can be used. This article is a part of a research that studied the combined effects of the addition of PET bottle fibres and fly ash (as a partial cement replacement) on the structural performance of concrete. From a purely engineering point of view, the research results indicate that the utilization and incorporation of PET and fly ash wastes in the construction industry are a viable solution to make concrete quality better. This article presents, beyond the engineering properties and experimental works, the economic and environmental advantages of the addition of these waste materials to the conventional concrete mixture. The addition of PET bottle fibres and fly ash resulted in positive cost implications providing a production cost reduction of 19% over the conventional concrete mixture. The removal of these materials from the environment also showed reduction of the emission of toxic elements to landfills and water bodies that put human, animal and plant lives in danger.
文摘This paper investigates the experimental results on the effect of nano silica fume on compressive strength development of concretes containing high volume fly ash (HVFA). The effect of various silica fumes contents such as 1%, 2% & 3% (wt. %) as partial replacement of cement on the compressive strength of cements is evaluated in the first part. The nano silica fume content which exhibits the highest compressive strength above is used in high volume fly ash concretes containing 30% and 50% class F fly ash. The results show that among three different silica fumes contents, the addition of 1% increases the compressive strength of concretes. The addition of 1% silica fume also increases the early age and 28 days compressive strengths of HVFA concretes.
基金the National Nature Science Foundation of China (No. 50679054)
文摘The enhancement effects of GH admixture on the early strengths of fly ash concrete and mortar were studied, and the mechanism was analyzed by X-ray diffraction (XRD) and scanning electro microscope (SEM). Experimental results show that, by the incorporation of GH admixture, both of cement hydration and pozzolanic reaction of fly ash are accelerated, the strengths of fly ash concrete and mortar are enhanced noticeably, especially the early strength. With a mixture design of 200 kg/m^3 OPC (Ordinary Portland Cement ), 200 kg/m^3 fly ash and 50 kg/m^3 GH admixture, the strength of concrete at 1 d, 3 d and 28 d reaches 25 MPa, 50 MPa and 70 MPa respectively.
文摘According to the life cycle assessment and the environmental design method of industry prnduction, a quantitative assessment model for the embodied environmetal impact of concrete with or without fly ash was proposed. The environmental burden impact indicator ( EBII ), the resources depletion impact indicator (RDII), and the environmental impact comprehensive indicator (EICI) are defined. The specific environmental impact values of different grade concretes with or wittout fly ash were presented. In the embodied process of concrete with or without fly ash, the key potential environmental impact categories are global warming and dust endsskin, and it is an effective way for reducing the embndied environmental impact of concrete to mix fly ash and lower grade cenwat . The method presented in this paper makes it possible to quantitatively assess the embodied environmental impact of concrete with or without .fly ash. The results calculated in this paper can be used to quantitatively assess the life cycle environmental impact of construction materials and buildings.
文摘The compressive strength,hydration products and microstructure of concrete with calcium-enriched fly ash(CEFA) at different temperature were investigated.The result indicates that the hydration products age of 7 d at-15 ℃ are mainly ettringite and C-S-H,and fly ash particles remain original state.Standard curing was adapted after 7 d curing at-15 ℃.At the age of 35 d,C-S-H was found on the surface of fly ash particles.The hydration product of CEFA is mainly C-S-H gel,which can densify the microstructure of concrete.