EMP control and characterization on high-power laser systems

Giant electromagnetic pulses(EMP) generated during the interaction of high-power lasers with solid targets can seriously degrade electrical measurements and equipment. EMP emission is caused by the acceleration of hot electrons inside the target, which produce radiation across a wide band from DC to terahertz frequencies. Improved understanding and control of EMP is vital as we enter a new era of high repetition rate, high intensity lasers(e.g. the Extreme Light Infrastructure).We present recent data from the VULCAN laser facility that demonstrates how EMP can be readily and effectively reduced. Characterization of the EMP was achieved using B-dot and D-dot probes that took measurements for a range of different target and laser parameters. We demonstrate that target stalk geometry, material composition, geodesic path length and foil surface area can all play a significant role in the reduction of EMP. A combination of electromagnetic wave and 3 D particle-in-cell simulations is used to inform our conclusions about the effects of stalk geometry on EMP,providing an opportunity for comparison with existing charge separation models.

Numerical simulation of debris-removal trajectories on the transport mirrors in high-power laser systems

In high-power laser systems(HPLSs), understanding debris-removal trajectories is important in eliminating debris from the surfaces of transport mirrors online and keeping other optical components free from contamination. NS equations, the RNG k–ε model and the discrete phase model of the Euler–Lagrange method are used to conduct numerical simulations on the trajectories of contaminant particles of different sizes and types on the mirror surface using Fluent commercial software. A useful device is fabricated based on the simulation results. This device can capture and collect debris from the mirror surface online. Consequently, the effect of debris contamination on other optical components is avoided,cleaning time is shortened, and ultimately, the cleanliness of the mirrors in HPLSs is ensured.

A new method for measuring the pulse-front distortion of arbitrary shapes in high-power ultrashort laser systems

We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the measurement of the pulse-front distortion of the pulse from a complex multi-pass amplification system, which exists in almost all high-power laser systems, and obtain the irregular pulse-front distribution. The method presented does not need any reference light or assumption about the pulse-front distribution, and has an accuracy of several femtoseconds.

Review of high-power pulsed systems at the Institute of High Current Electronics

In this paper,we give a review of some most powerful pulsed systems developed at the Institute of High Current Electronics(HCEI),Siberian Branch,Russian Academy of Sciences,and describe latest achievements of the teams dealing with these installations.Besides the presented high-power systems,HCEI performs numerous investigations using much less powerful generators.For instance,last year much attention was paying to the research and development of the intense low-energy(<200 kV)high-current electron and ion beam and plasma sources,and their application in the technology[1-3].

High-Power Single-Spatial-Mode GaSb Tapered Laser around 2.0 μm with Very Small Lateral Beam Divergence

We report high-power single-spatial-mode type-I GaSb-based tapered lasers fabricated on the InGaSb/AlGaAsSb material system. A straight ridge and three different tapered waveguide structures with varying flare angles are fabricated to optimize the output power and spatial-mode performance. The best devices exhibit single-spatial-mode operation with room-temperature output power up to 350？mW in continuous-wave mode at an emission wavelength around 2.0？μm with a very small far-field lateral divergence angle, which is beyond state of the art in terms of single-spatial-mode output power.

High-Power Passively Q-Switched Nd:YAG Laser at 1112 nm with a Cr^(4+):YAG Saturable Absorber

A high-power passively Q-switched Nd：YAG laser operating at lll2nm with Cr4＋：yAO as a saturable absorber is demonstrated. Under 808 nm diode-direct pumping, the maximum average output power of 2.73 W is achieved at the pump power of 16.65 W, corresponding to an optical-to-optical conversion efficiency of 16.4%. At the same time, the pulse width, pulse repetition rate, single pulse energy and peak power are 27.2ns, 9 kHz, 303.3#3 and 11.2kW, respectively. As far as we know, the result gives the highest average output power at 1112nm generated by an 808 nm diode-end-pumped Nd：YAG laser.

Elucidation of Metallic Plume and Spatter Characteristics Based on SVM During High-Power Disk Laser Welding

During deep penetration laser welding,there exist plume（weak plasma） and spatters,which are the results of weld material ejection due to strong laser heating.The characteristics of plume and spatters are related to welding stability and quality.Characteristics of metallic plume and spatters were investigated during high-power disk laser bead-on-plate welding of Type 304 austenitic stainless steel plates at a continuous wave laser power of 10 kW.An ultraviolet and visible sensitive high-speed camera was used to capture the metallic plume and spatter images.Plume area,laser beam path through the plume,swing angle,distance between laser beam focus and plume image centroid,abscissa of plume centroid and spatter numbers are defined as eigenvalues,and the weld bead width was used as a characteristic parameter that reflected welding stability.Welding status was distinguished by SVM（support vector machine） after data normalization and characteristic analysis.Also,PCA（principal components analysis） feature extraction was used to reduce the dimensions of feature space,and PSO（particle swarm optimization） was used to optimize the parameters of SVM.Finally a classification model based on SVM was established to estimate the weld bead width and welding stability.Experimental results show that the established algorithm based on SVM could effectively distinguish the variation of weld bead width,thus providing an experimental example of monitoring high-power disk laser welding quality.

high-power laser;off-axis reflective exposure system;pulse compression grating;spatial frequency errors;specifications

The large-aperture pulse compression grating(PCG) is a critical component in generating an ultra-high-intensity, ultra-short-pulse laser;however, the size of the PCG manufactured by transmission holographic exposure is limited to large-scale high-quality materials. The reflective method is a potential way for solving the size limitation, but there is still no successful precedent due to the lack of scientific specifications and advanced processing technology of exposure mirrors. In this paper, an analytical model is developed to clarify the specifications of components, and advanced processing technology is adopted to control the spatial frequency errors. Hereafter, we have successfully fabricated a multilayer dielectric grating of 200 mm × 150 mm by using an off-axis reflective exposure system with Φ300 mm. This demonstration proves that PCGs can be manufactured by using the reflection holographic exposure method and shows the potential for manufacturing the meter-level gratings used in 100 petawatt class high-power lasers.

High-Power Continuous-Wave and Acousto-Optical Q-Switched Ho:(Sc_(0.5)Y_(0.5))_2SiO_5 Laser Pumped by Laser Diode

We experimentally investigate the continuous-wave(cw)and acousto-optical(AO)Q-switched performance of a diode-pumped Ho:(Sc_(0.5)Y_(0.5))_2SiO_5(Ho:SYSO)laser.A fiber-coupled laser diode at 1.91m is employed as the pump source.The cw Ho:SYSO laser produces 13.0 W output power at 2097.9 nm and 56.0%slope efficiency with respect to the absorbed pump power.In the AO Q-switched regime,at a pulse repetition frequency of 5 kHz,the Ho:SYSO laser yields 2.1 mJ pulse energy and 21 ns pulse width,resulting in a calculated peak power of 100 k W.In addition,at the maximum output level,the beam quality factor of the Q-switched Ho:SYSO laser is measured to be about 1.6.

Formation of choroidal neovascularization under macular fovea after high-power laser irradiation: a case report

Dear Editor,I am Dr.Shan-Shan Li,from Northern Jiangsu People’s Hospital,Yangzhou,China.I write to present the case of formation of choroidal neovascularization(CNV)under the fovea after high-power laser irradiation.Currently,there is an increasing availability and accessibility to laser instruments,but improper use of these tools can lead to macular damage and irreversible visual impairment.

High-Power Dual-End-Pumped Actively Q-Switched Ho:YAG Ceramic Laser

We present a high-power Ho：YAG ceramic laser pumped at 1908nm. Using a dual-end-pumped structure, the maximum continuous-wave output power of 48 W is obtained, corresponding to a slope efficiency of 70.4% with respect to the absorbed pump power. At actively Q-switched mode, the maximum average output power of 46 W and the minimum pulse width of 21 ns are achieved at a pulse repetition frequency of 20 kHz, corresponding to a peak power of approximately 109.5kW. In addition, the beam-quality M2 factor is found to be 1.4 at the maximum output power.

High-Power Continuous-Wave Nd:GdVO4 Solid-State Laser Dual-End-Pumped at 880 nm

A high-power cw all-solid-state Nd：GdVO4 laser operating at 88Onto is reported. The laser consists of a low doped level Nd：GdV04 crystal dual-end-pumped by two high-power diode lasers and a compact negative confocM unstable-stable hybrid resonator. At an incident pump power of 820 W, a maximum cw output of 240 W at 1064nm is obtained. The optical-to-optical efficiency and Mope efficiency are 40.7% and 53.2%, respectively. The M2 factors in the unstable direction and in the stable direction are 4.38 and 5.44, respectively.

An accurate and stable method of array element tiling for high-power laser facilities

Due to laser-induced damage, the aperture of optics is one of the main factors limiting the output capability of highpower laser facilities. Because of the general difficulty in achieving large-aperture optics, an alternative solution is to tile some small-aperture ones together. We propose an accurate, stable, and automatic method of array element tiling and verify it on a double-pass 1 × 2 tiled-grating compressor in the XG-III laser facility. The test results show the accuracy and stability of the method. This research provides an efficient way to obtain large-aperture optics for high-power laser facilities.

High-Power and High-Efficiency Operation of Terahertz Quantum Cascade Lasers at 3.3 THz

A high-power and high-effciency GaAs/A1GaAs-based terahertz （THz） quantum cascade laser structure emitting at 3.3 THz is presented. The structure is based on a hybrid bound-to-continuum transition and resonant-phonon extraction active region combined with a semi-insulating surface-plasmon waveguide. By optimizing material structure and device processing, the peak optical output power of 758mW with a threshold current density of 120 A/cm2 and a wall-plug effciency of 0.92% at 10K and 404mW at 77K are obtained in pulsed operation. The maximum operating temperature is as high as llS K. In the cw mode, a record optical output power of 160roW with a threshold current density of 178A/cm2 and a wall-plug efficiency of 1.32% is achieved at 1OK.

In-situ Characterization of Non-aqueous Nano-dispersion Systems by Freeze-etching TEM and Comparative Study with Laser Scattering Method

In-situ characterization of non-aqueous nano-dispersion systems（NANDS） by freeze-etching transmission electron microscope（FETEM） was reported.To improve just-for-once successive rate of specimen preparation and get good characterization results,an improving specimen preparation method of freezing etching was developed.Size,distribution and morphology of NANDS were directly visualized.Some information of particle dispersion feature and particle density can also be obtained.Reproductivity of the FETEM characterization is excellent.Comparing with laser scattering method,which is liable to give positive error especially for small size particle anchoring disperser,FETEM characterization can give more accurate measurement of particle size.Moreover,FETEM can give dispersion feature of nanoparticle in non-aqueous medium.

Control systems and data management for high-power laser facilities

The next generation of high-power lasers enables repetition of experiments at orders of magnitude higher frequency than what was possible using the prior generation.Facilities requiring human intervention between laser repetitions need to adapt in order to keep pace with the new laser technology.A distributed networked control system can enable laboratory-wide automation and feedback control loops.These higher-repetition-rate experiments will create enormous quantities of data.A consistent approach to managing data can increase data accessibility,reduce repetitive data-software development and mitigate poorly organized metadata.An opportunity arises to share knowledge of improvements to control and data infrastructure currently being undertaken.We compare platforms and approaches to state-of-the-art control systems and data management at high-power laser facilities,and we illustrate these topics with case studies from our community.

flash-lamp pumping;high-power laser;laser cooling;neodymium glass;wavefront error

Mid-spatial frequency wavefront deformation can be deleterious for the operation of high-energy laser systems. When fluid cooled high-repetition-rate amplifiers are used, the coolant flow is likely to induce such detrimental mid-spatial frequency wavefront deformations. Here, we describe the design and performance of a 90 mm × 90 mm aperture, liquid-cooled Nd:phosphate split-slab laser amplifier pumped by flash-lamps. The performance of the system is evaluated in terms of wavefront aberration and gain at repetition rates down to 1 shot per minute. The results show that this single cooled split-slab system exhibits low wavefront distortions in the medium to large period range, compatible with a focus on target, and despite the use of liquid coolant traversed by both pump and amplified wavelengths. This makes it a potential candidate for applications in large high-energy laser facilities.

dispersion grating;frequency modulation-to-amplitude modulation conversion;high-power laser facility;inertial confinement fusion;phase modulation

Frequency modulation(FM)-to-amplitude modulation(AM) conversion is an important factor that affects the time±power curve of inertial confinement fusion(ICF) high-power laser facilities. This conversion can impact uniform compression and increase the risk of damage to optics. However, the dispersive grating used in the smoothing by spectral dispersion technology will introduce a temporal delay and can spatially smooth the target. The combined effect of the dispersive grating and the focusing lens is equivalent to a Gaussian low-pass filter, which is equivalent to 8 GHz bandwidth and can reduce the intensity modulation on the target to below 5% with 0.3 nm @ 3 GHz + 20 GHz spectrum phase modulation. The results play an important role in the testing and evaluating of the FM-to-AM on the final optics and the target, which is beneficial for comprehensively evaluating the load capacity of the facility and isentropic compression experiment for ICF.

Binary Laser Direct Writing System and Its Applications

A new laser direct writing system is introduced and the potential application of the diffractive optical elements (DOE’s) fabricated by applying laser direct writing system are presented. The fabrication techniques by applying the laser direct writing are developed. Experimental results have been obtained by applying laser direct writing machine with line width of 5μm and 10μm.