Damage effects and mechanism of the silicon NPN monolithic composite transistor induced by high-power microwaves

A two-dimensional model of the silicon NPN monolithic composite transistor is established for the first time by utilizing the semiconductor device simulator, Sentaurus-TCAD. By analyzing the internal distributions of electric field, current density, and temperature of the device, a detailed investigation on the damage process and mechanism induced by high-power microwaves （HPM） is performed. The results indicate that the temperature elevation occurs in the negative half-period and the temperature drop process is in the positive half-period under the HPM injection from the output port. The damage point is located near the edge of the base-emitter junction of T2, while with the input injection it exists between the base and the emitter of T2. Comparing these two kinds of injection, the input injection is more likely to damage the device than the output injection. The dependences of the damage energy threshold and the damage power threshold causing the device failure on the pulse-width are obtained, and the formulas obtained have the same form as the experimental equations, which demonstrates that more power is required to destroy the device if the pulse-width is shorter. Furthermore, the simulation result in this paper has a good coincidence with the experimental result.

An open-end high-power microwave-induced fracturing system for hard rock

Microwave pre-treatment is considered as a promising technique for alleviating cutter wear. This paper introduces a high-power microwave-induced fracturing system for hard rock. The test system consists of a high-power microwave subsystem (100 kW), a true triaxial testing machine, a dynamic monitoring subsystem, and an electromagnetic shielding subsystem. It can realize rapid microwave-induced fracturing, intelligent tuning of impedance, dynamic feedback under strong microwave fields, and active control of microwave parameters by addressing the following issues: the instability and insecurity of the system, the discharge breakdown between coaxial lines during high-power microwave output, and a lack of feedback of rock-microwave response. In this study, microwave-induced surface and borehole fracturing tests under true triaxial stress were carried out. Experimental comparisons imply that high-power microwave irradiation can reduce the fracturing time of hard rock and that the fracture range (160 mm) of a 915-MHz microwave source is about three times that of 2.45 GHz. After microwave-induced borehole fracturing, many tensile cracks occur on the rock surface and in the borehole: the maximum reduction of the P-wave velocity is 12.8%. The test results show that a high-power microwave source of 915 MHz is more conducive to assisting mechanical rock breaking and destressing. The system can promote the development of microwave-assisted rock breaking equipment.

Research progresses on Cherenkov and transit-time high-power microwave sources at NUDT

Research progresses on Cherenkov and transit-time high-power microwave(HPM)sources in National University of Defense Technology(NUDT)of China are presented.The research issues are focused on the following aspects.The pulse-shortening phenomenon in O-type Cerenkov HPM devices is suppressed.The compact coaxial relativistic backward-wave oscillators(RBWOs)at low bands are developed.The power efficiency in M-Type HPM tubes without guiding magnetic field increased.The power capacities and power efficiencies in the triaxial klystron amplifier(TKA)and relativistic transit-time oscillator(TTO)at higher frequencies increased.In experiments,some exciting results were obtained.The X-band source generated 2 GW microwave power with a pulse duration of 110 ns in 30 Hz repetition mode.Both L-and P-band compact RBWOs generated over 2 GW microwave power with a power efficiency of over 30%.There is approximately a 75% decline of the volume compared with that of conventional RBWO under the same power capacity conditions.A 1.755 GHz MILO produced 3.1 GW microwave power with power efficiency of 10.4%.A 9.37 GHz TKA produced the 240 MW microwave power with the gain of 34 dB.A 14.3 GHz TTO produced 1 GW microwave power with power efficiency of 20%.

Investigation on latch-up susceptibility induced by high-power microwave in complementary metal–oxide–semiconductor inverter

The latch-up effect induced by high-power microwave（HPM） in complementary metal–oxide–semiconductor（CMOS） inverter is investigated in simulation and theory in this paper. The physical mechanisms of excess carrier injection and HPM-induced latch-up are proposed. Analysis on upset characteristic under pulsed wave reveals increasing susceptibility under shorter-width pulsed wave which satisfies experimental data, and the dependence of upset threshold on pulse repetitive frequency（PRF） is believed to be due to the accumulation of excess carriers. Moreover, the trend that HPMinduced latch-up is more likely to happen in shallow-well device is proposed.Finally, the process of self-recovery which is ever-reported in experiment with its correlation with supply voltage and power level is elaborated, and the conclusions are consistent with reported experimental results.

High-power microwave propagation properties in the argon plasma array

The argon plasma induced by the L-/C-band high-power microwave(HPM) is investigated theoretically and experimentally. Influences of the microwave power, pulse width, polarization and the plasma electron density on the protection performance of the plasma array against HPM are studied. The results show that the effect of HPM is caused by energy accumulation, with the gas breakdown emerging only after a short time. The attenuation of the wave by the plasma array with the tubes off can reach approximately 23 dB at 1.3 GHz. It can also be obtained that the protection performance of the plasma array against the TE wave is better than that against the TM one. The plasma array shows better protection performance in the L-band than in the C-band. In addition,the attenuation of 5.6 GHz HPM can reach 30 dB when the tubes are turned on in the experiment.The research shows that the plasma array has protection ability against HPM.

Analysis of High-Power Microwave Propagation in a Magnetized Plasma Filled Waveguide

Plasma filling can dramatically improve the performance of high power microwave devices. The characteristics of high-power microwave propagation along plasma filled waveguides in an axial magnetic field are analyzed in this paper, and the ponderomotive force effect of high power microwave is taken into consideration. Theoretical analysis and preliminary numerical calculations are performed. The analyses show that the ponderomotive effect would change the plasma density, distribution of microwave field intensity, and dispersion of wave propagation. The higher the microwave power, the stronger the ponderomotive effect. In different magnetic fields, the ponderomotive effect is different.

Short-pulse high-power microwave breakdown at high pressures

The fluid model is proposed to investigate the gas breakdown driven by a short-pulse（such as a Gaussian pulse） highpower microwave at high pressures.However,the fluid model requires specification of the electron energy distribution function（EEDF）;the common assumption of a Maxwellian EEDF can result in the inaccurate breakdown prediction when the electrons are not in equilibrium.We confirm that the influence of the incident pulse shape on the EEDF is tiny at high pressures by using the particle-in-cell Monte Carlo collision（PIC-MCC） model.As a result,the EEDF for a rectangular microwave pulse directly derived from the Boltzmann equation solver Bolsig＋ is introduced into the fluid model for predicting the breakdown threshold of the non-rectangular pulse over a wide range of pressures,and the obtained results are very well matched with those of the PIC-MCC simulations.The time evolution of a non-rectangular pulse breakdown in gas,obtained by the fluid model with the EEDF from Bolsig＋,is presented and analyzed at different pressures.In addition,the effect of the incident pulse shape on the gas breakdown is discussed.

Design of High-power Microwave Waveguide Divider

A new LHW antenna will be used in LHCD system on tokanak HT-7U, where a high-power microwave waveguide power divider is a key device. This paper presents the power divider structure whose coupling element is in the common narrow wall between two identical waveguides, a certain of which is completely excavated. Green's Function Method is used to analyze the electric field distributions of the structure, and consequently the graphs between the scattering matrix and the geometrical dimensions are given. The graphs can be straightly applied to the process of the power divider.

Microwave Photonics for Modern Radar Systems

The emerging new concepts and technologies based on microwave photonics have led to an ever-increasing interest in developing innovative radar systems with a net gain in functionality,bandwidth /resolution,size,mass,complexity and cost when compared with the traditional implementations. This paper describes the techniques developed in the last few years in microwave photonics that might revolutionize the way to design multifunction radar systems,with an emphasis on the recent advances in optoelectronic oscillators( OEOs),arbitrary waveform generation,photonic mixing,phase coding,filtering,beamforming,analog-to-digital conversion,and stable radio-frequency signal transfer. Challenges in implementation of these components and subsystems for meeting the technique requirements of the multifunction radar applications are discussed.

Numerical simulation and inversion of offshore area depth based on x-band microwave radar

A detection method of offshore area depth utilizing the x-band microwave radar is proposed. The method is based on the sea clutter imaging mechanism of microwave radar, and combined with dispersion equation of the liner wave theorem and least square method （LSM）, consequently get the inversion results of water depth in the detected region. The wave monitoring system OSMAR-X exploited by the Ocean State Laborato-ry, Wuhan University, based on a microwave radar has proven to be a powerful tool to monitor ocean waves in time and space. Numerical simulation and inversion of offshore area depth are carried out here; since JONSWAP model can give description of stormy waves in different growth phase, it is suitable for simulation. Besides, some results from measured data detected by OSMAR-X x-band radar located at Longhai of Fujian Province, China, validates this method. The tendency of the average water depths inferred from the radar images is in good agreement with the tide level detected by Xiamen tide station. These promising results suggest the possibility of using OSMAR-X to monitor operationally morphodynamics in coastal zones. This method can be applied to both shore-based and shipborne x-band microwave radar.

An approach to a non-contact vital sign monitoring using dual-frequency microwave radars for elderly care

This study aimed to produce a prototype system for non-contact vital sign monitoring of the elderly using microwave radar with the intention of reducing the burdens on monitored individuals and nursing caregivers. In addition, we tested the ability of the proposed prototype system to measure the respiratory and heart rates of the elderly in a nursing home and discussed the systems effectiveness and problems by examining results of real-time monitoring. The prototype system consisted of two 24-GHz microwave radar antennas and an analysis system. The antennas were positioned below a mattress to monitor motion on the body surface for measuring cardiac and respiratory rates from the dorsal side of the subjects (23.3 ± 1.2 years) who would be lying on the mattress. The heart rates determined by the prototype system correlated significantly with those measured by electrocardiography (r = 0.92). Similarly, the respiratory rates determined by the prototype correlated with those obtained from respiration curves (r = 0.94). Next, we investigated the effectiveness of the prototype system with 7 elderly patients (93.3 ± 10.56 years) at a nursing home. The proposed system appears to be a promising tool for monitoring the vital signs of the elderly in a way that alleviates the need to attach electrodes overnight to confirm patient safety.

Noncontact Monitoring of Relative Changes in Blood Pressure Using Microwave Radar Sensors

This study aims to confirm whether noncontact monitoring of relative changes in blood pressure can be estimated using microwave radar sensors. First, an equation to estimate blood pressure was derived, after which, the effectiveness of the estimation equation was confirmed using data obtained by a noncontact method while inducing variations in blood pressure. We considered that the Bramwell-Hill equation, which contains some parameters that directly indicate changes in blood pressure, would be an appropriate reference to construct an estimation equation for the noncontact method, because measurements using microwave radar sensors can measure minute scale motion on the skin surface induced by the pulsation of blood vessels. In order to estimate relative changes in blood pressure, we considered a simple equation including the pulse transit time (PTT), amplitude of signals and body dimensions as parameters. To verify the effectiveness of the equation for estimating changes in blood pressure, two experiments were conducted: a cycling task using an ergometer, which induces blood pressure fluctuations because of changes in cardiac output, and a task using the Valsalva maneuver, which induces blood pressure fluctuations because of changes in vascular resistance. The results obtained from the two experiments suggested that the proposed equation using microwave radar sensors can accurately estimate relative changes of blood pressure. In particular, relatively favorable results were obtained for the changes in blood pressure induced by the changes in cardiac volume. Although many issues remain, this method could be expected to contribute to the continuous evaluation of cardiac function while reducing the burden on patients.

Non-intrusive soil carbon content quantification methods using machine learning algorithms:A comparison of microwave and millimeter wave radar sensors

Agricultural and forestry biomass can be converted to biochar through pyrolysis gasification,making it a significant carbon source for soil.Applying biochar to soil is a carbon-negative process that helps combat climate change,sustain soil biodiversity,and regulate water cycling.However,quantifying soil carbon content conventionally is time-consuming,labor-intensive,imprecise,and expensive,making it difficult to accurately measure in-field soil carbon’s effect on storage water and nutrients.To address this challenge,this paper for the first time,reports on extensive lab tests demonstrating non-intrusive methods for sensing soil carbon and related smart biochar applications,such as differentiating between biochar types from various biomass feedstock species,monitoring soil moisture,and biochar water retention capacity using portable microwave and millimeter wave sensors,and machine learning.These methods can be scaled up by deploying the sensor in-field on a mobility platform,either ground or aerial.The paper provides details on the materials,methods,machine learning workflow,and results of our investigations.The significance of this work lays the foundation for assessing carbon-negative technology applications,such as soil carbon content accounting.We validated our quantification method using supervised machine learning algorithms by collecting real soil mixed with known biochar contents in the field.The results show that the millimeter wave sensor achieves high sensing accuracy(up to 100%)with proper classifiers selected and outperforms the microwave sensor by approximately 10%–15%accuracy in sensing soil carbon content.

Environmentally Friendly and Multifunctional Shaddock Peel-Based Carbon Aerogel for Thermal-Insulation and Microwave Absorption

Eco-friendly electromagnetic wave absorbing materials with excellent thermal infrared stealth property,heat-insulating ability and compression resistance are highly attractive in practical applications.Meeting the aforesaid requirements simultaneously is a formidable challenge.Herein,ultra-light carbon aerogels were fabricated via fresh shaddock peel by facile freeze-drying method and calcination process,forming porous network architecture.With the heating platform temperature of 70℃,the upper surface temperatures of the as-prepared carbon aerogel present a slow upward trend.The color of the sample surface in thermal infrared images is similar to that of the surroundings.With the maximum compressive stress of 2.435 kPa,the carbon aerogels can provide favorable endurance.The shaddock peel-based carbon aerogels possess the minimum reflection loss value(RLmin)of−29.50 dB in X band.Meanwhile,the effective absorption bandwidth covers 5.80 GHz at a relatively thin thickness of only 1.7 mm.With the detection theta of 0°,the maximum radar cross-sectional(RCS)reduction values of 16.28 dB m^(2) can be achieved.Theoretical simulations of RCS have aroused extensive interest owing to their ingenious design and time-saving feature.This work paves the way for preparing multi-functional microwave absorbers derived from biomass raw materials under the guidance of RCS simulations.

Microwave damage susceptibility trend of a bipolar transistor as a function of frequency

We conduct a theoretical study of the damage susceptibility trend of a typical bipolar transistor induced by a high-power microwave （HPM） as a function of frequency. The dependences of the burnout time and the damage power on the signal frequency are obtained. Studies of the internal damage process and the mechanism of the device are carried out from the variation analysis of the distribution of the electric field, current density, and temperature. The investigation shows that the burnout time linearly depends on the signal frequency. The current density and the electric field at the damage position decrease with increasing frequency. Meanwhile, the temperature elevation occurs in the area between the p-n junction and the n n＋ interface due to the increase of the electric field. Adopting the data analysis software, the relationship between the damage power and frequency is obtained. Moreover, the thickness of the substrate has a significant effect on the burnout time.

Ultrabroad Microwave Absorption Ability and Infrared Stealth Property of Nano-Micro CuS@rGO Lightweight Aerogels

Developing ultrabroad radar-infrared compatible stealth materials has turned into a research hotspot,which is still a problem to be solved.Herein,the copper sulfide wrapped by reduced graphene oxide to obtain three-dimensional(3D)porous network composite aerogels(CuS@rGO)were synthesized via thermal reduction ways(hydrothermal,ascorbic acid reduction)and freeze-drying strategy.It was discovered that the phase components(rGO and CuS phases)and micro/nano structure(microporous and nanosheet)were well-modified by modulating the additive amounts of CuS and changing the reduction ways,which resulted in the variation of the pore structure,defects,complex permittivity,microwave absorption,radar cross section(RCS)reduction value and infrared(IR)emissivity.Notably,the obtained CuS@rGO aerogels with a single dielectric loss type can achieve an ultrabroad bandwidth of 8.44 GHz at 2.8 mm with the low filler content of 6 wt%by a hydrothermal method.Besides,the composite aerogel via the ascorbic acid reduction realizes the minimum reflection loss(RL_(min))of−60.3 dB with the lower filler content of 2 wt%.The RCS reduction value can reach 53.3 dB m^(2),which effectively reduces the probability of the target being detected by the radar detector.Furthermore,the laminated porous architecture and multicomponent endowed composite aerogels with thermal insulation and IR stealth versatility.Thus,this work offers a facile method to design and develop porous rGO-based composite aerogel absorbers with radar-IR compatible stealth.

Ultralight Magnetic and Dielectric Aerogels Achieved by Metal-Organic Framework Initiated Gelation of Graphene Oxide for Enhanced Microwave Absorption

The development of a convenient methodology for synthesizing the hierarchically porous aerogels comprising metal–organic frameworks(MOFs)and graphene oxide(GO)building blocks that exhibit an ultralow density and uniformly distributed MOFs on GO sheets is important for various applications.Herein,we report a facile route for synthesizing MOF/reduced GO(rGO)aerogels based on the gelation of GO,which is directly initiated using MOF crystals.Free metal ions exposed on the surface of MIL-88A nanorods act as linkers that bind GO nanosheets to a three-dimensional porous network via metal–oxygen covalent or electrostatic interactions.The MOF/rGOderived magnetic and dielectric aerogels Fe_(3)O_(4)@C/rGO and Ni-doped Fe_(3)O_(4)@C/rGO show notable microwave absorption(MA)performance,simultaneously achieving strong absorption and broad bandwidth at low thickness of 2.5(-58.1 dB and 6.48 GHz)and 2.8 mm(-46.2 dB and 7.92 GHz)with ultralow filling contents of 0.7 and 0.6 wt%,respectively.The microwave attenuation ability of the prepared aerogels is further confirmed via a radar cross-sectional simulation,which is attributed to the synergistic effects of their hierarchically porous structures and heterointerface engineering.This work provides an effective pathway for fabricating hierarchically porous MOF/rGO hybrid aerogels and offers magnetic and dielectric aerogels for ultralight MA.

Multifunctional MXene/C Aerogels for Enhanced Microwave Absorption and Thermal Insulation

Two-dimensional transition metal carbides and nitrides(MXene)have emerged as promising candidates for microwave absorption(MA)materials.However,they also have some drawbacks,such as poor impedance matching,high self-stacking tendency,and high density.To tackle these challenges,MXene nanosheets were incorporated into polyacrylonitrile(PAN)nanofibers and subsequently assembled into a three-dimensional(3D)network structure through PAN carbonization,yielding MXene/C aerogels.The 3D network effectively extends the path of microcurrent transmission,leading to enhanced conductive loss of electromagnetic(EM)waves.Moreover,the aerogel’s rich pore structure significantly improves the impedance matching while effectively reducing the density of the MXenebased absorbers.EM parameter analysis shows that the MXene/C aerogels exhibit a minimum reflection loss(RL_(min))value of−53.02 dB(f=4.44 GHz,t=3.8 mm),and an effective absorption bandwidth(EAB)of 5.3 GHz(t=2.4 mm,7.44–12.72 GHz).Radar cross-sectional(RCS)simulations were employed to assess the radar stealth effect of the aerogels,revealing that the maximum RCS reduction value of the perfect electric conductor covered by the MXene/C aerogel reaches 12.02 dB m^(2).In addition to the MA performance,the MXene/C aerogel also demonstrates good thermal insulation performance,and a 5-mm-thick aerogel can generate a temperature gradient of over 30℃ at 82℃.This study provides a feasible design approach for creating lightweight,efficient,and multifunctional MXene-based MA materials.

Hardening measures for bipolar transistors against microwave-induced damage

In the present paper we study the influences of the bias voltage and the external components on the damage progress of a bipolar transistor induced by high-power microwaves. The mechanism is presented by analyzing the variation in the internal distribution of the temperature in the device. The findings show that the device becomes less vulnerable to damage with an increase in bias voltage. Both the series diode at the base and the relatively low series resistance at the emitter, Re, can obviously prolong the burnout time of the device. However, Re will aid damage to the device when the value is sufficiently high due to the fact that the highest hot spot shifts from the base-emitter junction to the base region. Moreover, the series resistance at the base Rb will weaken the capability of the device to withstand microwave damage.

Dependence of plasma structure and propagation on microwave amplitude and frequency during breakdown of atmospheric pressure air

The structure and propagation of the plasma in air breakdown driven by high-power microwave have attracted great interest.This paper focuses on the microwave amplitude and frequency dependence of plasma formation at atmospheric pressure using one two-dimensional model,which is based on Maxwell’s equations coupled with plasma fluid equations.In this model,we adopt the effective electron diffusion coefficient,which can describe well the change from free diffusion in a plasma front to ambipolar diffusion in the bulk plasma.The filamentary plasma arrays observed in experiments are well reproduced in the simulations.The density and propagation speed of the plasma from the simulations are also close to the corresponding experimental data.The size of plasma filament parallel to the electric field decreases with increasing frequency,and it increases with the electric field amplitude.The distance between adjacent plasma filaments is close to one-quarter wavelength under different frequencies and amplitudes.The plasma propagation speed shows little change with the frequency,and it increases with the amplitude.The variations of plasma structure and propagation with the amplitude and frequency are due to the change in the distribution of the electric field.