Influence of introducing Zr,Ti,Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy

High pressure die casting(HPDC)AlSi10Mn Mg alloy castings are widely used in the automobile industry.Mg can optimize the mechanical properties of castings through heat treatment,while the release of thermal stress arouses the deformation of large integrated die-castings.Herein,the development of non-heat treatment Al alloys is becoming the hot topic.In addition,HPDC contains externally solidified crystals(ESCs),which are detrimental to the mechanical properties of castings.To achieve high strength and toughness of non-heat treatment die-casting Al-Si alloy,we used AlSi9Mn alloy as matrix with the introduction of Zr,Ti,Nb,and Ce.Their influences on ESCs and mechanical properties were systematically investigated through three-dimensional reconstruction and thermodynamic simulation.Our results reveal that the addition of Ti increased ESCs'size and porosity,while the introduction of Nb refined ESCs and decreased porosity.Meanwhile,large-sized Al_3(Zr,Ti)phases formed and degraded the mechanical properties.Subsequent introduction of Ce resulted in the poisoning effect and reduced mechanical properties.

Rock Breaking Performance of a Pick Assisted by High-pressure Water Jet under Different Configuration Modes

In the process of rock breaking, the conical pick bears great cutting force and wear, as a result, high-pressure water jet technology is used to assist with cutting. However, the effect of the water jet position has not been studied for rock breaking using a pick. Therefore, the models of rock breaking with different configuration modes of the water jet are established based on SPH combined with FEM. The effect of the water jet pressure, distance between the jet and the pick bit, and cutting depth on the rock breaking performance as well as a comparison of the tension and compression stress are studied via simulation; the simulation results are verified by experiments. The numerical and experimental results indicate that the decrease in the rates of the pick force obviously increases from 25 MPa to 40 MPa, but slowly after 40 MPa, and the optimal distance between the jet and the pick bit is 2 mm under the JFP and JSP modes. The JCP mode is proved the best, followed by the modes of JRP and JFP, and the worst mode is JSP. The decrease in the rates of the pick force of the JCP, JRP, JFP, and JSP modes are up to 30.96%, 28.96%, 33.46%, 28.17%, and 25.42%, respectively, in experiment. Moreover, the JSP mode can be regarded as a special JFP model when the distance between the pick-tip and the jet impact point is 0 mm. This paper has a dominant capability in introducing new numerical and experimental method for the study of rock breaking assisted by water jet and electing the best water jet position from four different configuration modes.

In situ experimental study on TBM excavation with high-pressure water-jet-assisted rock breaking

China’s first high-pressure hydraulically coupled rock-breaking tunnel boring machine(TBM) was designed to overcome the rock breaking problems of TBM in super-hard rock geology, where high-pressure water jet system is configured, including high-flow pump sets, high-pressure rotary joint and high-pressure water jet injection device. In order to investigate the rock breaking performance of high-pressure water-jet-assisted TBM, in situ excavation tests were carried out at the Wan’anxi Water Diversion Project in Longyan, Fujian Province, China, under different water jet pressure and rotational speed. The rock-breaking performance of TBM was analyzed including penetration, cutterhead load, advance rate and field penetration index. The test results show that the adoption of high-pressure water-jet-assisted rock breaking technology can improve the boreability of rock mass, where the TBM penetration increases by 64% under the water jet pressure of 270 MPa. In addition, with the increase of the water jet pressure, the TBM penetration increases and the field penetration index decreases. The auxiliary rock-breaking effect of high-pressure water jet decreases with the increase of cutterhead rotational speed. In the case of the in situ tunneling test parameters of this study, the advance rate is the maximum when the pressure of the high-pressure water jet is 270 MPa and the cutterhead rotational speed is 6 r/min. The technical superiority of high-pressure water-jet-assisted rock breaking technology is highlighted and it provides guidance for the excavation parameter selection of high-pressure hydraulically coupled rock-breaking TBM.

Composite rock-breaking of high-pressure CO_(2)jet&polycrystallinediamond-compact(PDC)cutter using a coupled SPH/FEM model

CO_(2) drilling is a promising underbalance drilling technology with great advantages,such as lower cutting force,intense cooling and excellent lubrication.However,in the underbalance drilling,the mechanism of the coupling CO_(2) jet and polycrystalline-diamond-compact(PDC)cutter are still unclear.Whereby,we established a coupled smoothed particle hydrodynamics/finite element method(SPH/FEM)model to simulate the composite rock-breaking of high-pressure CO_(2) jet&PDC cutter.Combined with the experimental research results,the mechanism of composite rock-breaking is studied from the perspectives of rock stress field,cutting force and jet field.The results show that the composite rock-breaking can effectively relieve the influence of vibration and shock on PDC cutter.Meanwhile,the high-pressure CO_(2) jet has a positive effect on carrying rock debris,which can effectively reduce the temperature rising and the thermal wear of the PDC cutter.In addition,the effects of CO_(2) jet parameters on composite rock-breaking were studied,such as jet impact velocity,nozzle diameter,jet injection angle and impact distance.The studies show that when the impact velocity of the CO_(2) jet is greater than 250 m/s,the CO_(2) jet could quickly break the rock.It is found that the optimal range of nozzle diameter is 1.5–2.5 mm,the best injection angle of CO_(2) jet is 60,the optimal impact distance is 10 times the nozzle diameter.The above studies could provide theoretical supports and technical guidance for composite rock-breaking,which is useful for the CO_(2) underbalance drilling and drill bit design.

Investigation of hydroxyl-terminated polybutadiene propellant breaking characteristics and mechanism impacted by submerged cavitation water jet

A submerged cavitation water jet(SCWJ)is an effective method to recycle solid propellant from obsolete solid engines by the breaking method.Solid propellant's breaking modes and mechanical process under SCWJ impact are unclear.This study aims to understand those impact breaking mechanisms.The hydroxyl-terminated polybutadiene(HTPB)propellant was chosen as the research material,and a self-designed test system was used to conduct impact tests at four different working pressures.The high-speed camera characterized crack propagation,and the DIC method calculated strain change during the impact process.Besides,micro and macro fracture morphologies were characterized by scanning electron microscope(SEM)and computed tomography(CT)scanning.The results reveal that the compressive strain concentration region locates right below the nozzle,and the shear strain region distributes symmetrically with the jet axis,which increases to 4% at first 16th ms,the compressive strain rises to 2% and 6% in the axial and transverse direction,respectively.The two tensile cracks formed first at the compression strain concentrate region,and there generate many shear cracks around the tensile cracks,and those shear cracks that develop and aggregate cause the cracks to become wider and cut through the tensile cracks,forming the tensile-shear cracks and the impact parts eventually fail.The HTPB propellant forms a breaking hole shaped conical after impact 10 s.The mass loss increases by 17 times at maximum,with the working pressure increasing by three times.Meanwhile,the damage value of the breaking hole remaining on the surface increases by 7.8 times while 2.9 times in the depth of the breaking hole.The breaking efficiency is closely affected by working pressures.The failure modes of HTPB impacted by SCWJ are classified as tensile crack-dominated and tensile-shear crack-dominated damage mechanisms.

Observation of Zero-Energy Modes with Possible Time-Reversal Symmetry Breaking on Step Edge of CaKFe_(4)As_(4)

Topologically nontrivial Fe-based superconductors attract extensive attentions due to their ability of hosting Majorana zero modes(MZMs)which could be used for topological quantum computation.Topological defects such as vortex lines are required to generate MZMs.Here,we observe the robust edge states along the surface steps of CaKFe_(4)As_(4).Remarkably,the tunneling spectra show a sharp zero-bias peak(ZBP)with multiple integerquantized states at the step edge under zero magnetic field.We propose that the increasing hole doping around step edges may drive the local superconductivity into a state with possible spontaneous time-reversal symmetry breaking.Consequently,the ZBP can be interpreted as an MZM in an effective vortex in the superconducting topological surface state by proximity to the center of a tri-junction with different superconducting order parameters.Our results provide new insights into the interplay between topology and unconventional superconductivity,and pave a new path to generate MZMs without magnetic field.

Nano-scale Reinforcements and Properties of Al-Si-Cu Alloy Processed by High-Pressure Torsion

To improve the comprehensive mechanical properties of Al-Si-Cu alloy,it was treated by a high-pressure torsion process,and the effect of the deformation degree on the microstructure and properties of the Al-Si-Cu alloy was studied.The results show that the reinforcements(β-Si andθ-CuAl_(2)phases)of the Al-Si-Cu alloy are dispersed in theα-Al matrix phase with finer phase size after the treatment.The processed samples exhibit grain sizes in the submicron or even nanometer range,which effectively improves the mechanical properties of the material.The hardness and strength of the deformed alloy are both significantly raised to 268 HV and 390.04 MPa by 10 turns HPT process,and the fracture morphology shows that the material gradually transits from brittle to plastic before and after deformation.The elements interdiffusion at the interface between the phases has also been effectively enhanced.In addition,it is found that the severe plastic deformation at room temperature induces a ternary eutectic reaction,resulting in the formation of ternary Al+Si+CuAl_(2)eutectic.

Experimental and Finite Element Analysis of Corroded High-Pressure Pipeline Repaired by Laminated Composite

Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necessary strength.Therefore,the experiments and analytical solutions presented in this paper are performed according to the relevant standards and codes,including ASME PCC-2,ASME B31.8S,ASME B31.4,ISO 24817 and ASME B31.G.In addition,the experimental tests are replicated numerically using the finite element method.Setting the strain gauges at different distances from the defect location,can reduce the nonlinear effects,deformation,and fluctuations due to the high pressure.The direct relationship between the depth of an axial defect and the stress concentration is observed at the inner side edges of the defect.Composite reparation reduces the non-linearities related to the sharp variation of the geometry and a more reliable numerical simulation could be performed.

Cavitation cloud impingement and scattering motion of jet in rock breaking process

The cavitation cloud impingement of the jet in the rock breaking process was experimentally investigated to reveal the jet erosion mechanism in drilling of petroleum exploitation. Serial erosion tests and flow visualization were performed, where the cavitation cloud motion in the erosion crater was obtained with the designed transparent specimen. Various erosion patterns were identified in the whole erosion process based on the eroded specimen topography. The shallow eroded crater with a shrinking erosion area is generated by the combination of impinging and scattering cavitation clouds. The increase of l_(d) promotes the development of cavitation cloud σ_(c) but reduces the impingement frequency f_(d), suggesting that the jet aggressive ability is enhanced when the balance between σ_(c) and f_(d) is reached. The cavitation cloud motion in the erosion crater was investigated with the transparent specimen. The erosion in the crater at shorter exposure periods T_(e) is generated by the combination of impingement and restricted scattering of cavitation clouds. With the continuous development of the erosion damage, the jet's aggressive ability is diminished due to the erosion expansion on sandstone, where the cavitation clouds impinge on the target and then collapse and vanish without restricted scattering.

CO_(2)high-pressure miscible flooding and storage technology and its application in Shengli Oilfield,China

There are various issues for CO_(2)flooding and storage in Shengli Oilfield,which are characterized by low light hydrocarbon content of oil and high miscible pressure,strong reservoir heterogeneity and low sweep efficiency,gas channeling and difficult whole-process control.Through laboratory experiments,technical research and field practice,the theory and technology of CO_(2)high pressure miscible flooding and storage are established.By increasing the formation pressure to 1.2 times the minimum miscible pressure,the miscibility of the medium-heavy components can be improved,the production percentage of oil in small pores can be increased,the displacing front developed evenly,and the swept volume expanded.Rapid high-pressure miscibility is realized through advanced pressure flooding and energy replenishment,and technologies of cascade water-alternating-gas(WAG),injection and production coupling and multistage chemical plugging are used for dynamic control of flow resistance,so as to obtain the optimum of oil recovery and CO_(2)storage factor.The research results have been applied to the Gao89-Fan142 in carbon capture,utilization and storage(CCUS)demonstration site,where the daily oil production of the block has increased from 254.6 t to 358.2 t,and the recovery degree is expected to increase by 11.6 percentage points in 15 years,providing theoretical and technical support for the large-scale development of CCUS.

Team China’s Groundbreaking Success at Paris Olympics

China’s Olympic delegation at the Paris 2024,with 404 athletes competing in 232 events across 30 sports,clinched 40 gold,27 silver,and 24 bronze medals,marking their best performance at an Olympics held abroad.The success of these athletes across various disciplines demonstrates the country’s efforts to expand its athletic prowess while also marks a new chapter for Chinese sportsmanship on the international stage.

Enhancing textile production:Smartex exhibits groundbreaking solutions

Smartex,a trailblazing leader in textile industry innovation,was proud to announce its return to ITM 2024,showcasing unparalleled advancements in quality control and production efficiency.Building on the success of previous exhibitions at ITM 2022 and ITMA Milan 2023,Smartex emerges stronger than ever,presenting its complete Smartex System tailored to transform textile manufacturing.

Spectral characteristics of underwater laser-induced breakdown spectroscopy under high-pressure conditions

Laser-induced breakdown spectroscopy(LIBS) has been proven to be an attractive technique for in situ oceanic applications.However,when applying LIBS into deep-sea,the pressure effect caused by different ocean depths is inescapable and could have great influence on the LIBS signals.In this work,spectral characteristics of underwater LIBS were investigated as a function of pressure in the range of 0.1-45 MPa.A high-pressure chamber built in the laboratory was used to simulate the high-pressure deep-sea environment.Optimal laser energy and detection delay were first determined under different pressure conditions and were shown to be independent of the external pressure.The increase in pressure has a significant impact both on the peak intensity and line broadening of the observed spectra.The peak intensity of Na,Li and K lines increases with the increasing pressure until a maximum intensity is reached at 12.5 MPa.Above this value,the peak intensity decreases gradually up to 45 MPa.For Ca line,the maximum intensity was observed at 30 MPa.The line broadening keeps constant at low pressures from 0.1-10 MPa,while it increases linearly at higher pressures,indicating a higher electron density caused by the compression effect of the high external pressure.We also compared the spectral data obtained from the high-pressure chamber and from the field sea trials,and the good consistency between the laboratory data and sea-trial data suggested the key role of pressure effect on underwater LIBS signals for practical deep-sea applications.

Study on Characters of Hard Seeds of Amphicarpaea edgeworthii Benth. (Leguminosae) and Methods for Breaking Dormancy

[Objective] This study aimed to understand the characters of hard seeds of Amphicarpaea edgeworthii Benth. （Leguminosae） and explore the methods for break- ing dormancy. [Method] For both aerial and subterranean seeds of A. edgeworthii, the morphological characteristics were observed and the appropriate temperature for germination was explored. For aerial seeds of A. edgeworthii, the characters of hard seeds were studied, and concentrated sulfuric acid treatment, hot water soak treat- ment and mechanical damage treatment were compared to explore the methods for breaking seed dormancy. [Result] The aerial seeds were oblate and averaged 3.38 mm in length, 3.02 mm in width, 1.88 mm in thickness, 15.32 g in thousand grain weight, with a hard seed rate after of up to 98% natural maturation. The subter- ranean seeds were approximately oblate with a maximum diameter of 15 mm and a hundred grain weight of （50.08-58.26 g）; among all the treatments for breaking hardseededness, cutting seed coat treatment and concentrated sulfuric acid treatment for 20 minutes were the most effective methods, whereas hot water soak treatment was the least effective method; constant temperature between 20 and 30 ℃ was optimum for the germination of aerial seeds, and alternative temperature of 30/20 ℃ was most appropriate for the germination of subterranean seeds. [Conclusion] Cutting seed coat treatment and concentrated sulfuric acid treatment for 20 minutes were the most effective methods to break the hardseededness of A. edgeworthii.

增强上肢力量对提高街舞的重要性研究——breaking舞种

根据调查没有接受过或者自发进行上肢力量锻炼的人群中有95%以上认为breaking中的难度动作很难完成,其难度动作中较为基础简单的动作都完成的很吃力,但是经过上肢力量锻炼的人群中有87%以上认为breaking中的难度动作相对比较容易,自己练习起来比较容易,控制能力明显比没有经过锻炼的人群要强很多,能正确地发力。

WAVE TRANSFORMATION AND BREAKING OVER A RECTANGULAR STEP

An idealized numerical wave flume has been established by finite element method on the bases of Navier Stokes equations through prescribing the appropriate boundary conditions for the open boundary,incident boundary,free surface and solid boundary in this paper.The characteristics of waves propagating over a step have been investigated by this numerical model.The breaker wave height is determined depending on the kinetic criterion.The numerical model is verified by laboratory experiments,and the empirical formula for the damping of wave height due to breaking is also given by experiments.

Dynamic Response Behaviors of Upright Breakwaters Under Breaking Wave Impact

The dynamic response behaviors of upright breakwaters under broken wave impact are analysed based on the mass-damper-spring dynamic system model. The effects of the mass, damping, stiffness, natural period, and impulse duration (or oscillation period) on the translation, rotation, sliding force, overturning moment, and corresponding dynamic amplifying factors are studied. It is concluded that the ampli-ying factors only depend on the ratio of the system natural period to impulse duration (or oscillation period) under a certain damping ratio. Moreover, the equivalent static approach to breakwater design is also discussed.

Physical Investigation of Directional Wave Focusing and Breaking Waves in Wave Basin

An experimental scheme for the generation of directional focusing waves in a wave basin is established in this paper. The effects of the directional range, frequency width and center frequency on the wave focusing are studied. The distribution of maximum amplitude and the evolution of time series and spectra during wave packet propagation and the variation of water surface parameters are extensively investigated. The results reveal that the characteristics of focusing waves are significantly influenced by wave directionality and that the breaking criteria for directional waves are distinctly different from those for unidirectional waves.

Numerical Simulation of Spatial Lag Between Wave Breaking Point and Location of Maximum Wave-Induced Current

A quasi three-dimensional numerical model of wave-driven coastal currents with the effects of surface rollers is developed for the study of the spatial lag between the location of the maximum wave-induced current and the wave breaking point. The governing equations are derived from Navier-Stokes equations and solved by the hybrid method combining the fractional step finite different method in the horizontal plane with a Galerkin finite element method in the vertical direc- tion. The surface rollers effects are considered through incorporating the creation and evolution of the roller area into the free surface shear stress. An energy equation facilitates the computation process which transfers the wave breaking energy dissipation to the surface roller energy. The wave driver model is a phase-averaged wave model based on the wave action balance equation. Two sets of laboratory experiments producing breaking waves that generated longshore currents on a planar beach am used to evaluate the model＇s performance. The present wave-driven coastal current model with the roller effect in the surface shear stress term can produce satisfactory results by increasing the wave-induced nearshore current velocity inside the surf zone and shifting the location of the maximum longshore current velocity landward.

Microwave backscattering from the sea surface with breaking waves

Based on the effective medium approximation theory of composites, the whitecap-covered sea surface is treated as a medium layer of dense seawater droplets and air. Two electromagnetic scattering models of randomly rough surface are applied to the investigation of microwave backscattering of breaking waves driven by strong wind. The shapes of seawater droplets are considered by calculating the effective dielectric constant of the whitecap layer. The responses of seawater droplets shapes, such as sphere and ellipsoid, to the backscattering coefficient are discussed. Numerical results of the models are in good agreement with the experimental measurements of horizontally and vertically polarized backscattering at microwave frequency 13.9GHz and different incidence angles.