Fluid Activity and Tectonic Evolution in the Northern Qilian High-pressure Metamorphic Belt

The Northern Qilian high-pressure metamorphic belt has experienced multipledeformation-metamorphism, which consists of at least four stages. In 550.8-526 Ma, eclogites wereformed. High temperature and pressure caused the escape of a large quantity of gas-liquid fluidsfrom rocks while silicate melt was generated. In the late stage, small amounts of CO_2 and H_2Oinfiltrating along fractures were introduced. In the formation of glaucophane schist (447-362 Ma),devolatilization reactions were dominated during the subduction-uplift stage of the paleoplate. Inthe uplift-exhumation stage (400-380 Ma) the increase of internal space of fractures in the rocksfavoured fluid infiltration and concentration. These fluids participated in hydration reactions inthe retro-metamorphism. The fluids participating in the mineral reactions have the compositions ofCaCl_2-NaCl-H_2O. In subsequent thrusting (<380 Ma), the metamorphic terrain was uplifted to theshallower crust and ductile-shearing deformation took place, which caused mainly dehydrationreactions of minerals. In a near-surface environment the metamorphic terrain experienced brittledeformation, forming many accompanying fractures. Immiscible CO_2 and low-salinity aqueous fluidsoccurred in these secondary microfractures and were trapped and sealed. The thermodynamic conditionsof different deformation-metamorphic stages of the metamorphic terrain were calculated and thecorresponding P-T-t path was deduced, showing that the metamorphic terrain has experienced aclockwise path indicated by T- and P-rising, and T- and P-falling processes. This reveals that thesubduction zone has undergone multiple tectono-dynamic processes, i.e. initial deep burial,subsequent quick uplift and near-surface tectonism.

The regulation of ferrocene-based catalysts on heat transfer in highpressure combustion of ammonium perchlorate/hydroxyl-terminated polybutadiene/aluminum composite propellants

The regulation of the burning rate pressure exponent for the ammonium perchlorate/hydroxylterminated polybutadiene/aluminum(AP/HTPB/Al)composite propellants under high pressures is a crucial step for its application in high-pressure solid rocket motors.In this work,the combustion characteristics of AP/HTPB/Al composite propellants containing ferrocene-based catalysts were investigated,including the burning rate,thermal behavior,the local heat transfer,and temperature profile in the range of 7-28 MPa.The results showed that the exponent breaks were still observed in the propellants after the addition of positive catalysts(Ce-Fc-MOF),the burning rate inhibitor((Ferrocenylmethyl)trimethylammonium bromide,Fc Br)and the mixture of Fc Br/catocene(GFP).However,the characteristic pressure has increased,and the exponent decreased from 1.14 to 0.66,0.55,and 0.48 when the addition of Ce-FcMOF,Fc Br and Fc Br/GFP in the propellants.In addition,the temperature in the first decomposition stage was increased by 7.50℃ and 11.40℃ for the AP/Fc Br mixture and the AP/Fc Br/GFP mixture,respectively,compared to the pure AP.On the other hand,the temperature in the second decomposition stage decreased by 48.30℃ and 81.70℃ for AP/Fc Br and AP/Fc Br/GFP mixtures,respectively.It was also found that Fc Br might generate ammonia to cover the AP surface.In this case,a reaction between the methyl in Fc Br and perchloric acid caused more ammonia to appear at the AP surface,resulting in the suppression of ammonia desorption.In addition,the coarse AP particles on the quenched surface were of a concave shape relative to the binder matrix under low and high pressures when the catalysts were added.In the process,the decline at the AP/HTPB interface was only exhibited in the propellant with the addition of Ce-Fc-MOF.The ratio of the gas-phase temperature gradient of the propellants containing catalysts was reduced significantly below and above the characteristic pressure,rather than 3.6 times of the difference in the blank propellant.Overall,the obtained results demonstrated that the pressure exponent could be effectively regulated and controlled by adjusting the propellant local heat and mass transfer under high and low pressures.

The Key Influence of Fluid in the Preserves, Mineral Assemblages, Compositionsand Structures: Study from High-Pressure Eclogite and Its Amphibolization in the Western Dabie Mountains,Central China

Pseudosection modeling for the garnet amphibolite samples from the Western Dabie Mountains show they have experienced similar HP metamorphic evolution with that of the adjected eclogites.The common assemblage of

The Key Influence of Fluid in Metamorphic Rock Preserves, Mineral Assemblages, Compositions and Structures: Study from High-Pressure Eclogite and Its Amphibolization in the Western Dabie Mountains,Central China

The most of high/ultrahigh-pressure(HP/UHP)terranes of the world are characterized by the occurrence of numerous pods,lenses or layered blocks of eclogite and amphibolites(e.g.O’Brien,1997;Elvevold and Gilotti,2000;Zhang et al.,2003;and references there in).Field and petrological features suggest that amphibolites should

Constraints of REE and trace elements of high-pressure-veins and host rocks in western Tianshan on origin of deep fluids in paleosubduction zones

The western Tianshan high-pressure(HP) metamorphic belt represents the paleosubduction mélange of paleozoic south Tianshan ocean between the Yili-central Tianshan and Tarim plates. High-pressure veins are extensively developed in this HP belt. Compared with normal mid-ocean ridge basalt(N-MORB), the high-pressure veins and host rocks are enriched in light rare earth elements(LREE) and incompatible elements. But high-pressure veins show a larger variation than host rocks in total REE abundance. On the trace element spidergram, all the samples are enriched in incompatible elements and show strong positive Pb anomaly relative to N-MORB. The array tendency lines of plots of the HP rocks have apparent slopes on diagram of m(Sr) vs m(Sr)/m(Zr), m(Li) vs m(Li)/m(Y) and (m(Ce)) vs m(Ce)/m(Pb), which indicates that the enrichment in LREE and incompatible elements relative to N-MORB of the HP-metamorphic rocks from western Tianshan is not attributed to magma evolution process of the protolith. High field strength elements, such as Nb, Ta, Ti, Zr and Hf, do not show negative anomaly relative to N-MORB, which is dissimilar to that of island arc basalts. Therefore, the enrichment in LREE and incompatible elements of the HP rocks is not attributed to the enrichment of the source of the protolith. The mass ratios of Rb to Ba, Ce to Pb, Nb to U and Ta to U of high-pressure veins and host rocks are intermediate of mid-ocean ridge basalt or oceanic island basalt and continental crust. The fluids in western Tianshan paleosubduction zones are mixtures of two sources, dehydration or devolatilization of host rocks and of subducted sediments.

Fluid flow on centimeter-scale in deep paleosubduction zones in western Tianshan,China:Evidence from high-pressure veins

High-pressure(HP)veins were extensively developed in western Tianshan high-pressure(HP)metamorphic belt.The HP vein and host-rocks were analyzed by electronic microprobe to trace the origin of vein-forming fluids.Analytical data show that the immediately adjacent host-rocks of the studied HP vein are eclogites and gradually turned into blueschist as the distance from the veins increases,which indicates that the vein-forming fluid was derived from adjacent host-rocks;the boundaries between the vein and the host-rocks are sharp,which indicates that the fracture of the host-rocks is brittle during the vein-forming process.It is suggested that this type of HP veins is precipitated from the liquid formed by the dehydration of the host-rocks during the prograde metamorphism from blueschist to eclogite facies,which results in hydrofracturing of the rocks and provides the space for the vein to precipitate.The width of the eclogite-facies host-rocks is usually 1-2 cm,which provides the direct evidence that the fluid flow is on centimeter-scale.

Pressure transient characteristics of non-uniform conductivity fractured wells in viscoelasticity polymer flooding based on oil-water two-phase flow

Polymer flooding in fractured wells has been extensively applied in oilfields to enhance oil recovery.In contrast to water,polymer solution exhibits non-Newtonian and nonlinear behavior such as effects of shear thinning and shear thickening,polymer convection,diffusion,adsorption retention,inaccessible pore volume and reduced effective permeability.Meanwhile,the flux density and fracture conductivity along the hydraulic fracture are generally non-uniform due to the effects of pressure distribution,formation damage,and proppant breakage.In this paper,we present an oil-water two-phase flow model that captures these complex non-Newtonian and nonlinear behavior,and non-uniform fracture characteristics in fractured polymer flooding.The hydraulic fracture is firstly divided into two parts:high-conductivity fracture near the wellbore and low-conductivity fracture in the far-wellbore section.A hybrid grid system,including perpendicular bisection(PEBI)and Cartesian grid,is applied to discrete the partial differential flow equations,and the local grid refinement method is applied in the near-wellbore region to accurately calculate the pressure distribution and shear rate of polymer solution.The combination of polymer behavior characterizations and numerical flow simulations are applied,resulting in the calculation for the distribution of water saturation,polymer concentration and reservoir pressure.Compared with the polymer flooding well with uniform fracture conductivity,this non-uniform fracture conductivity model exhibits the larger pressure difference,and the shorter bilinear flow period due to the decrease of fracture flow ability in the far-wellbore section.The field case of the fall-off test demonstrates that the proposed method characterizes fracture characteristics more accurately,and yields fracture half-lengths that better match engineering reality,enabling a quantitative segmented characterization of the near-wellbore section with high fracture conductivity and the far-wellbore section with low fracture conductivity.The novelty of this paper is the analysis of pressure performances caused by the fracture dynamics and polymer rheology,as well as an analysis method that derives formation and fracture parameters based on the pressure and its derivative curves.

A Study to Observe Pulse Pressure Variation after Induction with Propofol for General Anesthesia

Background and Aims: Pulse pressure variation (PPV) is a reliable and predictive dynamic parameter presently being utilized for fluid responsiveness. In the operating room, fluid administration based on PPV monitoring helps the physician in deciding whether to volume resuscitate or use interventions in patients undergoing surgery. Propofol is an intravenous induction agent which lowers blood pressure. There are multiple causes such as depression in cardiac output, and peripheral vasodilatation for hypotension. We undertook this study to observe the utility of PPV as a guide to fluid therapy after propofol induction. Primary outcome of our study was to monitor PPV as a marker of fluid responsiveness for the hypotension caused by propofol induction. Secondary outcome included the correlation of PPV with other hemodynamic parameters like heart rate (HR), systolic blood pressure (SBP), and diastolic blood pressure (DBP);after induction with propofol at regular interval of time. Methods: A total number of 90 patients were recruited. Either of the radial artery was then cannulated under local anaesthesia with 20G VygonLeadercath arterial cannula and invasive monitoring transduced. A baseline recording of heart rate (HR), systolic blood pressure (SBP), diastolic blood pressure (DBP) and PPV was then recorded. Patients were then induced with predetermined doses of propofol (2 mg/kg) and recordings of HR, SBP, DBP, and PPV were taken at 5, 10 and 15 minutes. Results: Intraoperatively, PPV was significantly higher at 5 minutes and significantly lower at 15 minutes after induction. It was observed that there were no statistically significant correlations between PPV and SBP or DBP. PPV was strongly and directly associated with HR. Conclusion: We were able to establish that PPV predicts fluid responsiveness in hypotension caused by propofol induction;and can be used to administer fluid therapy in managing such hypotension. However, PPV was not directly correlated with hypotension subsequent to propofol administration.

Ultrasound based estimate of central venous pressure:Are we any closer?

Central venous pressure(CVP)serves as a direct approximation of right atrial pressure and is influenced by factors like total blood volume,venous compliance,cardiac output,and orthostasis.Normal CVP falls within 8-12 mmHg but varies with volume status and venous compliance.Monitoring and managing disturbances in CVP are vital in patients with circulatory shock or fluid disturbances.Elevated CVP can lead to fluid accumulation in the interstitial space,impairing venous return and reducing cardiac preload.While pulmonary artery catheterization and central venous catheter obtained measurements are considered to be more accurate,they carry risk of complications and their usage has not shown clinical improvement.Ultrasound-based assessment of the internal jugular vein(IJV)offers real-time,non-invasive measurement of static and dynamic parameters for estimating CVP.IJV parameters,including diameter and ratio,has demonstrated good correlation with CVP.Despite significant advancements in non-invasive CVP measurement,a reliable tool is yet to be found.Present methods can offer reasonable guidance in assessing CVP,provided their limitations are acknowledged.

Action mechanisms of abnormal fluid pressure on physical properties of deep reservoirs: A case study on Jurassic Toutunhe Formation in the southern margin of Junggar Basin, NW China

Considering the action mechanisms of overpressure on physical changes in skeleton particles of deep reservoir rocks and the differences in physical changes of skeleton particles under overpressure and hydrostatic pressure, the sandstone of the Jurassic Toutunhe Formation in the southern margin of Junggar Basin was taken as an example for physical modeling experiment to analyze the action mechanisms of overpressure on the physical properties of deep reservoirs. (1) In the simulated ultra-deep layer with a burial depth of 6000-8000 m, the mechanical compaction under overpressure reduces the remaining primary pores by about a half that under hydrostatic pressure. Overpressure can effectively suppress the mechanical compaction to allow the preservation of intergranular primary pores. (2) The linear contact length ratio under overpressure is always smaller than the linear contact length ratio under hydrostatic pressure at the same depth. In deep reservoirs, the difference between the mechanical compaction degree under overpressure and hydrostatic pressure shows a decreasing trend, the effect of abnormally high pressure to resist the increase of effective stress is weakened, and the degree of mechanical compaction is gradually close to that under hydrostatic pressure. (3) The microfractures in skeleton particles of deep reservoirs under overpressure are thin and long, while the microfractures in skeleton particles of deep reservoirs under hydrostatic pressure are short and wide. This difference is attributed to the probable presence of tension fractures in the rocks containing abnormally high pressure fluid. (4) The microfractures in skeleton particles under overpressure were mainly formed later than that under hydrostatic pressure, and the development degree and length of microfractures both extend deeper. (5) The development stages of microfractures under overpressure are mainly controlled by the development stages of abnormally high pressure and the magnitude of effective stress acting on the skeleton particles. Moreover, the development stages of microfractures in skeleton particles are more than those under hydrostatic pressure in deep reservoir. The multi-stage abnormally high pressure plays an important role in improving the physical properties of deep reservoirs.

Pre-Drilling Prediction Techniques on the High-Temperature High-Pressure Hydrocarbon Reservoirs Offshore Hainan Island,China

Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure(HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques(PPTs). To improve the accuracy of geopressure prediction in HTHP hydrocarbon reservoirs offshore Hainan Island, we made a comprehensive summary of current PPTs to identify existing problems and challenges by analyzing the global distribution of HTHP hydrocarbon reservoirs, the research status of PPTs, and the geologic setting and its HTHP formation mechanism. Our research results indicate that the HTHP formation mechanism in the study area is caused by multiple factors, including rapid loading, diapir intrusions, hydrocarbon generation, and the thermal expansion of pore fluids. Due to this multi-factor interaction, a cloud of HTHP hydrocarbon reservoirs has developed in the Ying-Qiong Basin, but only traditional PPTs have been implemented, based on the assumption of conditions that do not conform to the actual geologic environment, e.g., Bellotti's law and Eaton's law. In this paper, we focus on these issues, identify some challenges and solutions, and call for further PPT research to address the drawbacks of previous works and meet the challenges associated with the deepwater technology gap. In this way, we hope to contribute to the improved accuracy of geopressure prediction prior to drilling and provide support for future HTHP drilling offshore Hainan Island.

CFD simulation of gas–liquid flow in a high-pressure bubble column with a modified population balance model

In this study,based on the Luo bubble coalescence model,a model correction factor C_e for pressures according to the literature experimental results was introduced in the bubble coalescence efficiency term.Then,a coupled modified population balance model(PBM) with computational fluid dynamics(CFD) was used to simulate a high-pressure bubble column.The simulation results with and without C_e were compared with the experimental data.The modified CFD-PBM coupled model was used to investigate its applicability to broader experimental conditions.These results showed that the modified CFD-PBM coupled model can predict the hydrodynamic behaviors under various operating conditions.

Spectral characteristics of underwater laser-induced breakdown spectroscopy under high-pressure conditions

Laser-induced breakdown spectroscopy(LIBS) has been proven to be an attractive technique for in situ oceanic applications.However,when applying LIBS into deep-sea,the pressure effect caused by different ocean depths is inescapable and could have great influence on the LIBS signals.In this work,spectral characteristics of underwater LIBS were investigated as a function of pressure in the range of 0.1-45 MPa.A high-pressure chamber built in the laboratory was used to simulate the high-pressure deep-sea environment.Optimal laser energy and detection delay were first determined under different pressure conditions and were shown to be independent of the external pressure.The increase in pressure has a significant impact both on the peak intensity and line broadening of the observed spectra.The peak intensity of Na,Li and K lines increases with the increasing pressure until a maximum intensity is reached at 12.5 MPa.Above this value,the peak intensity decreases gradually up to 45 MPa.For Ca line,the maximum intensity was observed at 30 MPa.The line broadening keeps constant at low pressures from 0.1-10 MPa,while it increases linearly at higher pressures,indicating a higher electron density caused by the compression effect of the high external pressure.We also compared the spectral data obtained from the high-pressure chamber and from the field sea trials,and the good consistency between the laboratory data and sea-trial data suggested the key role of pressure effect on underwater LIBS signals for practical deep-sea applications.

Safety estimation of high-pressure hydraulic cylinder using FSI method

Hydraulic cylinder is a primary component of the hydraulic valve systems.The numerical study of hydraulic cylinder to evaluate the stress analysis,the life assessment and the performance of operation characteristics in hydraulic cylinder were described.The calculation of safety factor,fatigue life,piston chamber pressure,rod chamber pressure and the change of velocity of piston with flow time after the beginning of hydraulic cylinder were incorporated.Numerical analysis was performed using the commercial CFD code,ANSYS with unsteady,dynamic mesh model,two-way FSI(fluid-structure interaction)method and k-εturbulent model.The internal pressure in hydraulic cylinder through stress analysis show higher than those of the yield strength.

In-situ pressure-preserved coring for deep exploration:Insight into the rotation behavior of the valve cover of a pressure controller

In-situ pressure-preserved coring(IPP-Coring)is considered to be the most reliable and efficient method for the identification of the scale of oil and gas resources.During IPP-Coring,because the rotation behavior of the pressure controller valve cover in different medium environments is unclear,interference between the valve cover and inner pipe may occur and negatively affect the IPP-Coring success rate.To address this issue,we conducted a series of indoor experiments employing a high-speed camera to gain greater insights into the valve cover rotation behavior in different medium environments,e.g.,air,water,and simulated drilling fluids.The results indicated that the variation in the valve cover rotation angle in the air and fluid environments can be described by a one-phase exponential decay function with a constant time parameter and by biphasic dose response function,respectively.The rotation behavior in the fluid environments exhibited distinct elastic and gravitational acceleration zones.In the fluid environments,the density clearly impacted the valve cover closing time and rotation behavior,whereas the effect of viscosity was very slight.This can be attributed to the negligible influence of the fluid viscosity on the drag coefficient found in this study;meanwhile,the density can increase the buoyancy and the time period during which the valve cover experienced a high drag coefficient.Considering these results,control schemes for the valve cover rotation behavior during IPP-Coring were proposed for different layers and geological conditions in which the different drilling fluids should be used,e.g.,the use of a high-density valve cover in high-pore pressure layers.

Analytical solutions for dynamic pressures of coupling fluid-solid-porous medium due to P wave incidence

Wave reflection and refraction in layered media is a topic closely related to seismology,acoustics,geophysics and earthquake engineering.Analytical solutions for wave reflection and refraction coefficients in multi-layered media subjected to P wave incidence from the elastic half-space are derived in terms of displacement potentials.The system is composed of ideal fluid,porous medium,and underlying elastic solid.By numerical examples,the effects of porous medium and the incident wave angle on the dynamic pressures of ideal fluid are analyzed.The results show that the existence of the porous medium,especially in the partially saturated case,may significantly affect the dynamic pressures of the overlying fluid.

Fundamentals and Processes of Fluid Pressure Forming Technology for Complex Thin-Walled Components

A new generation of fluid pressure forming technology has been developed for the three typical structures of tubes,sheets,and shells,and hard-to-deform material components that are urgently needed for aerospace,aircraft,automobile,and high-speed train industries.in this paper,an over all review is introduced on the state of the art in fundamentals and processes for lower-pressure hydroforming of tubular components,double-sided pressure hydroforming of sheet components,die-less hydroforming of ellipsoidai shells,and dual hardening hot medium forming af hard-to-deform materiais Particular attention is paid to deformation behavior,stress state adjustment,defect prevention,and typical applications.In addition,future development directions of fluid pressure forming technology are discussed,including hyper lower-loading forming for ultra-large non-uniform components,precision for ming for intermetallic compound and high-entropy alloy components,intelligent process and equipment,and precise finite element simulation of inhomogeneous and strong anisotropic thin shells.

High temperature and high pressure rheological properties of high-density water-based drilling fluids for deep wells

To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids （fresh water-based and brine-based） under high temperature and high pressure （HTHP） with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.

Determining Pressure with Daughter Minerals in Fluid Inclusion by Raman Spectroscopy:Sphalerite as an Example

Raman frequency of some materials, including minerals, molecules and ions, shifts systematically with changing pressure and temperature. This property is often used as a pressure gauge in high pressure experiments with the hydrothermal diamond anvil cell （HDAC）. Since the system of fluid inclusion is similar to that of HDAC, it can also be used to determine the internal pressure of fluid inclusions. Sphalerite is a common daughter mineral. In this study, the frequency shift of the 350 cm-1 peak of sphalerite has been studied from 296 to 523 K and from 0.07 to 2.00 GPa using the HDAC. The global slope of the isotherms （V350/p）T is 0.0048 in the studied pressure range. No significant variation of the slopes with temperature has been observed. The correlation between the frequency shift of the 350 cm-1 peak of sphalerite and pressure and temperature is constrained as P=208.33（△ Vp）350＋3.13T-943.75. This relationship may be used to estimate the internal pressure of the sphalerite-bearing fluid inclusions.

Rheological properties of oil-based drilling fluids at high temperature and high pressure

The rheological properties of two kinds of oil-based drilling fluids with typically composition were studied at pressures up to 138 MPa and temperatures up to 204 ℃ using the RheoChan 7400 Rheometer.The experimental results show that the apparent viscosity,plastic viscosity and yield point decrease with the increase of temperature,and increase with the increase of pressure.The effect of pressure on the apparent viscosity,plastic viscosity and yield point is considerable at ambient temperature.However,this effect gradually reduces with the increase of temperature.The major factor influencing the rheological properties of oil-based drilling fluids is temperature instead of pressure in the deep sections of oil wells.On the basis of numerous experiments,the model for predict the apparent viscosity,plastic viscosity and yield point of oil-based drilling fluids at high temperature and pressure was established using the method of regressive analysis.It is confirmed that the calculated data are in good agreement with the measured data,and the correlation coefficients are more than 0.98.The model is convenient for use and suitable for the application in drilling operations.