Gas Film Disturbance Characteristics Analysis of High-Speed and High-Pressure Dry Gas Seal

The dry gas seal（DGS） has been widely used in high parameters centrifugal compressor, but the intense vibrations of shafting, especially in high-speed condition, usually result in DGS＇s failure. So the DGS＇s ability of resisting outside interference has become a determining factor of the further development of centrifugal compressor. However, the systematic researches of which about gas film disturbance characteristics of high parameters DGS are very little. In order to study gas film disturbance characteristics of high-speed and high-pressure spiral groove dry gas seal（S-DGS） with a flexibly mounted stator, rotor axial runout and misalignment are taken into consideration, and the finite difference method and analytical method are used to analyze the influence of gas film thickness disturbance on sealing performance parameters, what＇s more, the effects of many key factors on gas film thickness disturbance are systematically investigated. The results show that, when sealed pressure is 10.1MPa and seal face average linear velocity is 107.3 m/s, gas film thickness disturbance has a significant effect on leakage rate, but has relatively litter effect on open force; Excessively large excitation amplitude or excessively high excitation frequency can lead to severe gas film thickness disturbance; And it is beneficial to assure a smaller gas film thickness disturbance when the stator material density is between 3.1 g/cm3 to 8.4 g/cm3; Ensuring sealing performance while minimizing support axial stiffness and support axial damping can help to improve dynamic tracking property of dry gas seal. The proposed research provides the instruction to optimize dynamic tracking property of the DGS.

A study of hydrate plug formation in a subsea natural gas pipeline using a novel high-pressure flow loop

The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content （10%） of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.

Mold Filling and Prevention of Gas Entrapment in High-pressure Die-casting

This paper presents some results of direct observation of mold filling in a specially designed die-casting by X-ray diffraction, including comparison with numerical simulation. Based on such work the authors discuss how to prevent gas entrapment and propose new methods.

Productivity Analysis Method of Abnormal High-Pressure Gas Reservoir in Ying-Qiong Basin

Ying-Qiong Basin in the west of South China Sea contains plenty of abnormal high-pressure gas reservoirs, whose stress sensitivity is crucial for well productivity. To explore the influence of stress sensitivity on production, the variable outlet back pressure stress sensitivity experiments were applied to test core sample permeability under different burden pressure and obtain the relational expression of power function of core stress sensitivity. Afterwards, new productivity equation is deduced in consideration of reservoir stress sensitivity, and the affection of stress sensitivity on production is analyzed. The result demonstrates close link between stress sensitivity and productivity, since single well production decreases dramatically when reservoir stress sensitivity has been taken into account. This research is constructive for well-testing data interpretation in stress sensitive gas reservoirs.

Numerical Simulation Analysis of the Transformer Fire Extinguishing Process with a High-Pressure Water Mist System under Different Conditions

To thoroughly study the extinguishing effect of a high-pressure water mist fire extinguishing system when a transformer fire occurs,a 3D experimental model of a transformer is established in this work by employing Fire Dynamics Simulator(FDS)software.More specifically,by setting different parameters,the process of the highpressure water mist fire extinguishing system with the presence of both diverse ambient temperatures and water mist sprinkler laying conditions is simulated.In addition,the fire extinguishing effect of the employed high-pressure water mist system with the implementation of different strategies is systematically analyzed.The extracted results show that a fire source farther away fromthe centerline leads to a lower local temperature distribution.In addition,as the ambient temperature increases,the temperature above the fire source decreases,while the temperature and the concentrationof theupperflue gas layer bothdecrease.Interestingly,after thehigh-pressurewatermist sprinkler begins to operate,both the temperature distribution above the fire source and the concentration of the flue gas decrease,which indicates that the high-pressure water mist system plays the role of cooling and dust removal.By comparing various sprinkler laying methods,it is found that the lower sprinkler height has a better effect on the temperature above the fire source,the temperature of the upper flue gas layer,and the concentration of the flue gas.Moreover,when the sprinkler is spread over thewhole transformer,the cooling effect on both the temperature above the fire source and the temperature of the upper flue gas layer is good,whereas the change in the concentration of the flue gas above the fire source is not obvious compared to the case where the sprinkler is not fully spread.

Dynamic effects of high-pressure pulsed water jet in low-permeability coal seams

Mine gas extraction in China is difficult due to the characteristics such as micro-porosity,low-permeability and high adsorption of coal seams.The pulsed mechanismof a high-pressure pulsed water jet was studied through theoretical analysis,experimentand field measurement.The results show that high-pressure pulsed water jet has threedynamic properties.What's more,the three dynamic effects can be found in low-permeabilitycoal seams.A new pulsed water jet with 200-1 000 Hz oscillation frequency andpeak pressure 2.5 times than average pressure was introduced.During bubble collapsing,sound vibration and instantaneous high pressures over 100 MPa enhanced the cuttingability of the high-pressure jet.Through high-pressure pulsed water jet drilling and slotting,the exposure area of coal bodies was greatly enlarged and pressure of the coal seamsrapidly decreased.Therefore,the permeability of coal seams was improved and gas absorptionrate also decreased.Application results show that gas adsorption rate decreasedby 30%-40%and the penetrability coefficient increased 100 times.This proves that high-pressurepulsed water is more efficient than other conventional methods.

Formation of Large-Volume High-Pressure Plasma in Triode-Configuration Discharge Devices

A ＂plane cathode micro-hollow anode discharge （PCHAD）＂ is studied in comparison with micro-hollow cathode discharge （MHCD）. A new triode-configuration discharge device is also designed for large-volume, high-pressure glow discharges plasma without glow-to-arc transitions, as well as with an anode metal needle, and a cathode of PCHAD. It has a ＂needle-hole＂ sustained glow discharge. Its discharge circuit employs only one power supply circuit with a variable resistor. The discharge experiments have been carried out in the air. The electrical properties and the photoimages in PCHAD, multi-PCHAD and ＂needle-hole＂ sustained discharge have been investigated. The electrical and the optical measurements show that this triode-configuration discharge device can operate stably at high-pressure, in parallel without individual ballasting resistance. And the electron density of the plasma is estimated to be up to 10^12cm^-3. Compared with the twosupply circuit system, this electrode configuration is very simple with lower cost in generating large-volume plasma at high pressures.

Research on thermal insulation materials properties under HTHP conditions for deep oil and gas reservoir rock ITP-Coring

Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability,resulting in distorted resource assessments.The development of in situ temperaturepreserved coring(ITP-Coring)technology for deep reservoir rock is urgent,and thermal insulation materials are key.Therefore,hollow glass microsphere/epoxy resin thermal insulation materials(HGM/EP materials)were proposed as thermal insulation materials.The materials properties under coupled hightemperature and high-pressure(HTHP)conditions were tested.The results indicated that high pressures led to HGM destruction and that the materials water absorption significantly increased;additionally,increasing temperature accelerated the process.High temperatures directly caused the thermal conductivity of the materials to increase;additionally,the thermal conduction and convection of water caused by high pressures led to an exponential increase in the thermal conductivity.High temperatures weakened the matrix,and high pressures destroyed the HGM,which resulted in a decrease in the tensile mechanical properties of the materials.The materials entered the high elastic state at 150℃,and the mechanical properties were weakened more obviously,while the pressure led to a significant effect when the water absorption was above 10%.Meanwhile,the tensile strength/strain were 13.62 MPa/1.3%and 6.09 MPa/0.86%at 100℃ and 100 MPa,respectively,which meet the application requirements of the self-designed coring device.Finally,K46-f40 and K46-f50 HGM/EP materials were proven to be suitable for ITP-Coring under coupled conditions below 100℃ and 100 MPa.To further improve the materials properties,the interface layer and EP matrix should be optimized.The results can provide references for the optimization and engineering application of materials and thus technical support for deep oil and gas resource development.

Investigations of methane adsorption characteristics on marine-continental transitional shales and gas storage capacity models considering pore evolution

Methane adsorption is a critical assessment of the gas storage capacity(GSC)of shales with geological conditions.Although the related research of marine shales has been well-illustrated,the methane adsorption of marine-continental transitional(MCT)shales is still ambiguous.In this study,a method of combining experimental data with analytical models was used to investigate the methane adsorption characteristics and GSC of MCT shales collected from the Qinshui Basin,China.The Ono-Kondo model was used to fit the adsorption data to obtain the adsorption parameters.Subsequently,the geological model of GSC based on pore evolution was constructed using a representative shale sample with a total organic carbon(TOC)content of 1.71%,and the effects of reservoir pressure coefficient and water saturation on GSC were explored.In experimental results,compared to the composition of the MCT shale,the pore structure dominates the methane adsorption,and meanwhile,the maturity mainly governs the pore structure.Besides,maturity in the middle-eastern region of the Qinshui Basin shows a strong positive correlation with burial depth.The two parameters,micropore pore volume and non-micropore surface area,induce a good fit for the adsorption capacity data of the shale.In simulation results,the depth,pressure coefficient,and water saturation of the shale all affect the GSC.It demonstrates a promising shale gas potential of the MCT shale in a deeper block,especially with low water saturation.Specifically,the economic feasibility of shale gas could be a major consideration for the shale with a depth of<800 m and/or water saturation>60%in the Yushe-Wuxiang area.This study provides a valuable reference for the reservoir evaluation and favorable block search of MCT shale gas.

Research on physical explosion crater model of high-pressure natural gas pipeline

In this study,Hypermesh and LS-DYNA numerical simulation software are used to build a multi domain coupling model of natural gas pipeline,including soil,pipeline,TNT explosive and air domain,and the non-reflection boundary conditions are set for the model.The TNT equivalent method is used to convert the physical explosion amount of natural gas pipeline into 1387.38 kg TNT explosive amount.The simulation results show that the physical explosion of pipeline forms an approximate elliptical crater with a width of 12.68 m and a depth of 4.12 m;the TNT equivalent of the model is corrected by comparing the crater simulation value and the size value of the crater calculated by the PRCI empirical formula under the same laying condition,and the correction coefficient is selected as O.9,and the cor-rected TNT equivalent is 1248.64 kg:the modified model crater size is 3.72 m deep and 12.66 m wide,compared with the crater size obtained from the field test,the error of crater depth and width calculated by the modified model simulation is 5.7%and 15.5%respectively.

Numerical simulation and optimization design of the EGR cooler in vehicle

The EGR (exhaust gas recirculation) technique can greatly reduce the NOx emission of diesel engines, especially when an EGR cooler is employed. Numerical simulations are applied to study the flow field and temperature distributions inside the EGR cooler. Three different models of EGR cooler are investigated, among which model A is a traditional one, and models B and C are improved by adding a helical baffle in the cooling area. In models B and C the entry directions of cooling water are different, which mostly influences the flow resistance. The results show that the improved structures not only lengthen the flow path of the cooling water, but also enhance the heat exchange rate between the cool and hot media. In conclusion we suggest that the improved structures are more powerful than the traditional one.

Natural gas density under extremely high pressure and high temperature: Comparison of molecular dynamics simulation with corresponding state model

This work applied molecular dynamics(MD)simulation to calculate densities of natural gas mixtures at extremely high pressure(>138 MPa)and high temperature(>200℃)conditions(x HPHT)to bridge the knowledge and technical gaps between experiments and classical theories.The experimental data are scarce at these conditions which are also out of assumptions for classical predictive correlations,such as the Dranchuk&Abou-Kassem(DAK)equation of state(EOS).Force fields of natural gas components were carefully chosen from literatures and the simulation results are validated with experimental data.The largest relative error is 2.67%for pure hydrocarbons,2.99%for C1/C3 mixture,7.85%for C1/C4 mixture,and 8.47%for pure H2S.These satisfactory predictions demonstrate that the MD simulation approach is reliable to predict natural-and acid-gases thermodynamic properties.The validated model is further used to generate data for the study of the EOS with pressure up to 276 MPa and temperature up to 573 K.Our results also reveal that the Dranchuk&Abou-Kassem(DAK)EOS is capable of predicting natural gas compressibility to a satisfactory accuracy at x HPHT conditions,which extends the confidence range of the DAK EOS.

Development of a simplified n-heptane/methane model for high-pressure direct-injection natural gas marine engines

High-pressure direct-injection (HPDI) of natu- ral gas is one of the most promising solutions for future ship engines, in which the combustion process is mainly controlled by the chemical kinetics. However, the employment of detailed chemical models for the multi-dimensional combustion simulation is significantly expensive due to the large scale of the marine engine. In the present paper, a reduced n-heptane/methane model consisting of 35-step reactions was constructed using multiple reduction approaches. Then this model was further reduced to include only 27 reactions by utilizing the HyChem (Hybrid Chemistry) method. An overall good agreement with the experimentally measured ignition delay data of both n-heptane and methane for these two reduced models was achieved and reasonable predictions for the measured laminar flame speeds were obtained for the 35-step model. But the 27-step model cannot predict the laminar flame speed very well. In addition, these two reduced models were both able to reproduce the experimentally measured in-cylinder pressure and heat release rate profiles for a HPDI natural gas marine engine, the highest error of predicted combustion phase being 6.5%. However, the engine-out CO emission was over-predicted and the highest error of predicted NOx emission was less than 12.9%. The predicted distributions of temperature and equivalence ratio by the 35-step and 27-step models are similar to those of the 334-step model. However, the predicted distributions of OH and CH2O are significantly different from those of the 334-step model. In short, the reduced chemical kinetic models developed provide a high-efficient and dependable method to simulate the characteristics of combustion and emissions in HPDI natural gas marine engines.

Study on the inflammatory cytokines after heterotopic transplantation of isolated mouse heart preserved in a high-pressured mixed gas chamber

Background The maintenance of heart viability is important for heart transplantation. Currently, heart preservation is limited to 6 hours of cold ischemic storage. This study explored a new heart preservation method under a high-pressured mixed gas chamber. Methods C57BL/6 male mice were used to establish the model of mice cervical heterotopic heart transplantation. Adult donor mice were randomly divided into three groups subjected to naive operation （Group A）, standard control （Group B） and experimental control （Group C）. The recipient mice were randomly divided into two groups subjected to standard control and experimental control. Group A： hearts were isolated; Group B： hearts were isolated and preserved in HTK solution at 4 ℃ for 8 h and transplanted; Group C： hearts were isolated and preserved in high pressured gas （PO2：3200 hPa ＋ PCO： 800 hPa = 4000 hPa） at 4 ℃ for 8h and transplanted. After transplantation, the state of re-beating and cardiac function were observed for Group B and C. At 24 h after transplantation, samples were collected for HE staining, cardiac cell apoptosis detection by Tunnel staining and analysis of tumor necrosis factor α （TNF-α）, interleukin-1β （IL-1β）, interleukin-6 （IL-6） and interleukin-10 （IL-10） by reverse transcriotion-polymerase chain reaction （RT-PCR）. Results In group C, 15 transplanted hearts were re-beat, while only 6 in Group B. The re-beating rate in Group C was significantly higher than Group B [75.0%（15/20） vs. 30.0%（6/20） ,P = 0.01]. The time of re-beating was significantly different between Group B, and C [（352.35 ± 61.07）s vs. （207.85 ± 71.24） s, P 〈 0.011. HE staining showed that pathologic changes such as ceil edema and inflammatory cell infiltration were more obvious in Group B and C than in Group A, but less obvious in Group C compared with Group B. Tunnel staining showed that Group B had more obvious apoptosis than Group A and C. RT-PCR results showed significant increase of TNF-α, IL-1β and IL-6 expression in Group B than Group C （P 〈 0.01, the expression of IL-10 was higher in Group C than that in Group B. Conclusion Highpressured mixed gas （PO2：3200 hPa ＋ PCO： 800 hPa = 4000 hPa） preservation can reduce cold ischemia and reperfusion injury of donor heart, therefore to maintain myocardial viability and prolong preservation time of donor heart.

Effect of particle size on high-pressure methane adsorption of coal

Adsorbed gas cannot be neglected in the evaluation of coalbed methane and shale gas since a significant proportion of gas is stored in the form of adsorbed gas.Adsorbed methane of coal and shale has been widely studied by high-pressure methane adsorption experiment.In sample treatment of the experiment,the sample is crushed and sieved to a particular particle size range.However,how particle size influence high-pressure methane adsorption is still unclear.In this study,low-pressure nitrogen(N_(2))and high-pressure methane adsorption have been measured on coal samples with different particle size.According to N2 sorption analysis,pore volume and surface area increase with particle size reduction.Pore size distribution of small pores(<10nm)changes among varying particle size.Pore volume proportion of small pores(<10nm)increases and pore volume proportion of big pores(>10nm)decreases with decreasing particle size.Decreasing particle size by crushing sample introduces new connectivity for closed pores to the particle surface.The responses of isotherms of high-pressure methane adsorption are different with different particle size.Methane adsorption at initial pressure(145psi)increases with decreasing particle size.Adsorption increase rate at high pressure(435-870psi)decreases with particle size reduction.This can be explained that fine sample has more pore volume and higher pore volume proportion of small pores(<10nm).Sample with particle size of 150-250μm has the highest Langmuir volume.

Theoretical simulation of high-voltage discharge with runaway electrons in sulfur hexafluoride at atmospheric pressure

The results of theoretical simulation of runaway electron generation in high-pressure pulsed gas discharge with inhomogeneous electric field are presented.Hydrodynamic and kinetic approaches are used simultaneously to describe the dynamics of different components of low-temperature discharge plasma.Breakdown of coaxial diode occurs in the form of a dense plasma region expanding from the cathode.On this background there is a formation of runaway electrons that are initiated by the ensemble of plasma electrons generated in the place locally enhanced electric field in front of dense plasma.It is shown that the power spectrum of fast electrons in the discharge contains electron group with the so-called“anomalous”energy.

CFD performance analysis of finned-tube CO_(2)gas coolers with various inlet air flow patterns

A detailed model of three-dimensional computational fluid dynamics(CFD)on a finned-tube CO_(2)gas cooler has been developed and validated.The model is then applied to investigate the effect of uniform and mal-distribution inlet airflow profiles on the coil performance.The airflow mal-distribution velocity profiles include linear-up,linear-down and parabolic while the effected coil performance parameters contain airside pressure drop,average airside heat transfer coefficient,approach temperature and coil heating capacity.The model also enables to predict the CO_(2)refrigerant temperature profile along the coil pipes from refrigerant inlet to outlet at different operation conditions.The simulation results reveal that different types of inlet airflow velocity profiles have significant effects on the gas cooler performance.The uniform airflow velocity profile case shows the best thermal performance of gas cooler.Compared with the cases of linear-up and parabolic air velocity profiles,the linear-down airflow profile can influence more on the coil heat transfer performance.Due to the thermal conduction between neighbour tubes through coil fins,reversed heat transfer phenomenon exists which can be detected and simulated by the CFD model.It is predicted that the linear-down airflow profile can increase greatly the reversed heat transfer phenomenon and thus lead to the highest approach temperature and the lowest heating capacity amongst these four types of airflow profiles.The research method and outcomes presented in this paper can have great potentials to optimize the performance of a CO_(2)gas cooler and its associated refrigeration system.

Multi-Scale Pore Structure Heterogeneity in Tuff Reservoirs Investigated with Multi-Experimental Method and Fractal Dimensions in Chang 7 Formation,Southern Ordos Basin

The tight tuff reservoir is an unusual type of unconventional reservoir with strong heterogeneity.However,there is a lack of research on the microscopic pore structure that causes the heterogeneity of tuff reservoirs.Using the Chang 7 Formation in Ordos Basin,China as a case study,carbon-dioxide gas adsorption,nitrogen gas adsorption and high-pressure mercury injection are integrated to investigate the multi-scale pore structure characteristics of tuff reservoirs.Meanwhile,the fractal dimension is introduced to characterize the complexity of pore structure in tuff reservoirs.By this multi-experimental method,the quantitative characterizations of the full-range pore size distribution of four tuff types were obtained and compared in the size ranges of micropores,mesopores and macropores.Fractal dimension curves derived from full-range pores are divided into six segments as D1,D2,D3,D4,D5 and D6 corresponding to fractal characteristics of micropores,smaller mesopores,larger mesopores,smaller macropores,medium macropores and larger macropores,respectively.The macropore volume,average macropore radius and fractal dimension D5 significantly control petrophysical properties.The larger macropore volume,average macropore radius and D5 correspond to favorable pore structure and good reservoir quality,which provides new indexes for the tuff reservoir evaluation.This study enriches the understanding of the heterogeneity of pore structures and contributes to unconventional oil and gas exploration and development.

Porphyrin/Fullerene Porous Molecular Cocrystal Featuring a Robust One-Dimensional Channel

Microporous molecular crystals are promising materials because of their designable porosity as well as their resistance to chemical and other stimuli.Here,we developed microporous molecular cocrystals by taking advantage of the specific interactions between porphyrins and fullerene molecules.Single-crystal X-ray diffraction analysis revealed that one nickel(Ⅱ)porphyrin interacts with two fullerene molecules to form a two-dimensional honeycomb network with an eclipsed stacking mode,providing onedimensional void channels.After the pores were activated by heat treatment or mechanical grinding,the prepared cocrystal can incorporate gas and solvent molecules reversibly while maintaining its single-crystallinity.Also,it retained its single-crystallinity in the presence of water,acid−base,or high pressure.These findings in this study expand the availability of molecular crystals based on intermolecular interactions as porous materials,which are expected to work under conditions that have not been applicable to other molecule-based porous materials.

Efficiency Analysis of an Arrayed Liquid Piston Isothermal Air Compression System for Compressed Air Energy Storage

Compressed air energy storage(CAES)is an important technology in the development of renewable energy.The main advantages of CAES are its high energy capacity and environmental friendliness.One of the main challenges is its low energy density,meaning a natural cavern is required for air storage.High-pressure air compression can effectively solve the problem.A liquid piston gas compressor facilitates high-pressure compression,and efficient convective heat transfer can significantly reduce the compression energy consumption during air compression.In this paper,a near isothermal compression method is proposed to increase the surface area and heat exchange by using multiple tube bundles in parallel in the compression chamber in order to obtain high-pressure air using liquid-driven compression.Air compression with a compression ratio of 6.25:1 is achieved by reducing the tube diameter and increasing the parallel tube number while keeping the compression chamber cross-sectional area constant in order to obtain a high-pressure air of 5 MPa.The performances of this system are analyzed when different numbers of tubes are applied.A system compression efficiency of 93.0%and an expansion efficiency of 92.9%can be achieved when 1000 tubes are applied at a 1 minute period.A new approach is provided in this study to achieve high efficiency and high pressure compressed air energy storage.