Recently,magnesium and its alloys have attracted more and more attention as promising implant materials due to their excellent properties such as good biocompatibility,biodegradation,non-toxicity and comparable mechan...Recently,magnesium and its alloys have attracted more and more attention as promising implant materials due to their excellent properties such as good biocompatibility,biodegradation,non-toxicity and comparable mechanical properties with natural bone.They can be gradually degraded and absorbed so as to avoid the second surgery for implants removal after the tissues are healed completely.In addition,they are also able to prevent the stress shielding effect in human body environment because of the density,elastic modulus and yield strength of magnesium closer to the bone.Unfortunately,the high corrosion rate which causes early mechanical failure of the implants in physiological environment limits the widespread use of magnesium alloys for clinical application in biology.And the high corrosion process usually causes huge hydrogen evolution and alkalinization,resulting in problems against the implants as well as the surrounding tissues.In order to enhance the corrosion resistance of magnesium alloys,in this study,the ZEK100 magnesium alloy was pre-deformed with a highpressure torsion(HPT)process and then fabricated hydroxyapatite(HA)coatings with different contents of Mg(OH)2 nanopowder via hydrothermal method.The specimens were characterized by scanning electron microscope(SEM)and X-ray diffraction(XRD).At the same time,prior and after the HPT procedure,the metallography,microhardness and tensile tests of specimens were characterized.Meanwhile,the corrosion behavior of the specimens was evaluated by electrochemical impedance spectroscopy(EIS)and hydrogen evolution tests.And the interface bonding strength of the HA coating on the magnesium alloy substrate was evaluated by a tape adhesion test/scratch test.Results showed that HPT processing refined the grain size and introduced a great number of twins,resulting in the enhancement of microhardness and Young’s modulus of ZEK100 magnesium alloy,but hardness values at the edge were higher than those at the center due to the uneven shear strain.At the same conditions,the HA coating on HPT-ZEK was denser,thicker than that on ZEK sample and the crystal sizes of HA were smaller on HPT-ZEK.These were attributed to fine,uniform distributed secondary phases and lots of fine grains,twins,grain boundaries in HPT-ZEK substrates which can provide more nucleation sites for the HA crystal.In terms of the amount of Mg(OH)2 nanopowder,Mg(OH)2 nanopowder significantly influenced the microstructure and thickness of the HA coating.And at a 0.3 mg/mL content of Mg(OH)2 nanopowder,there was the densest,thickest HA coating on magnesium alloys,and the crystal size of HA was minimum.Specifically,the HA coating thickness on ZEK-03(0.3 mg/mL Mg(OH)2 nanopowder)was 1.8 times of that on ZEK-00(0 mg/mL Mg(OH)2 nanopowder),while the HA coating thickness on HPT-03 was 2.6 times of that on ZEK-00.And the adhesion strength of HA coating on HPT-03 substrate was better than that on ZEK-03.In addition,HPT technology and surface modification by HA coating simultaneously increased the corrosion resistance of ZEK100 magnesium alloy and the corrosion of HPT-ZEK samples occurred in a more uniform manner,while it was pitting on the surface of ZEK100 magnesium alloy.Therefore,there was the best corrosion resistance on HPT-03 sample,which could promote the application of magnesium alloys in biomedical fields.展开更多
Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necess...Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necessary strength.Therefore,the experiments and analytical solutions presented in this paper are performed according to the relevant standards and codes,including ASME PCC-2,ASME B31.8S,ASME B31.4,ISO 24817 and ASME B31.G.In addition,the experimental tests are replicated numerically using the finite element method.Setting the strain gauges at different distances from the defect location,can reduce the nonlinear effects,deformation,and fluctuations due to the high pressure.The direct relationship between the depth of an axial defect and the stress concentration is observed at the inner side edges of the defect.Composite reparation reduces the non-linearities related to the sharp variation of the geometry and a more reliable numerical simulation could be performed.展开更多
High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase...High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase and retained nanocrystalline;second is the alternating bands of amorphous phase and high defect density crystalline.As a result,post deformation annealing(PDA)at 500-700℃leads to the non-uniform distribution of martensite and parent phase grains.The grains of martensite are twice larger compared to that of parent phase.The nanocrystalline and ultrafine grains form after annealing at 500-600℃and 700℃,respectively.The twinning mechanism does not change with the reduction of martensitic grains up to^35 nm.The relationship between strength and grain size in Ti29.7Ni50.3Hf20 alloy obeys the classical Hall-Petch relationship with a coefficient of 10.80±0.39 GPa nm^1/2.展开更多
The wear characteristics of Cu and Cu-SiC composite microsize powders consolidated by cold compaction combined with sintering or high-pressure torsion(HPT)were investigated.The HPT processed(HPTed)samples with b...The wear characteristics of Cu and Cu-SiC composite microsize powders consolidated by cold compaction combined with sintering or high-pressure torsion(HPT)were investigated.The HPT processed(HPTed)samples with bimodal and trimodal microstructures and fine Cu grains and SiC particle sizes have superior hardness,reasonable ductility level,and high wear resistance.The wear mass loss and coefficient of friction of HPTed samples were remarkably lower than that of cold-compacted and sintered samples as well as that of micro and nano Cu and Cu-SiC composites from previous studies.The sample fabrication method has an apparent influence on the wear mechanism.The wear mechanism was converted from adhesive,delamination,three-body mechanism,grooves(take off the SiC particles),and cracks into abrasive wear after HPT.Oxidization can be considered a dominant wear mechanism in all cases.The worn surface morphology and analysis support the relationship between wear mechanism and characteristics.展开更多
Cu samples were subjected to high-pressure torsion (HPT) with up to 6 turns at room temperature (RT) and liquid nitrogen temperature (LNT),respectively.The effects of temperature on grain refinement and microhardness ...Cu samples were subjected to high-pressure torsion (HPT) with up to 6 turns at room temperature (RT) and liquid nitrogen temperature (LNT),respectively.The effects of temperature on grain refinement and microhardness variation were investigated.For the samples after HPT processing at RT,the grain size reduced from 43 μm to 265 nm,and the Vickers microhardness increased from HV52 to HV140.However,for the samples after HPT processing at LNT,the value of microhardness reached its maximum of HV150 near the center of the sample and it decreased to HV80 at the periphery region.Microstructure observations revealed that HPT straining at LNT induced lamellar structures with thickness less than 100 nm appearing near the central region of the sample,but further deformation induced an inhomogeneous distribution of grain sizes,with submicrometer-sized grains embedded inside micrometer-sized grains.The submicrometer-sized grains with high dislocation density indicated their nonequilibrium nature.On the contrary,the micrometer-sized grains were nearly free of dislocation,without obvious deformation trace remaining in them.These images demonstrated that the appearance of micrometer-sized grains is the result of abnormal grain growth of the deformed fine grains.展开更多
Monoclinicα-MoP_(2),with the OsGe2-type structure(space group C2/m,Z=4)and lattice parameters a=8.7248(11)Å,b=3.2322(4)Å,c=7.4724(9)Å,andβ=119.263°,was synthesized under a pressure of 4~GPa at a ...Monoclinicα-MoP_(2),with the OsGe2-type structure(space group C2/m,Z=4)and lattice parameters a=8.7248(11)Å,b=3.2322(4)Å,c=7.4724(9)Å,andβ=119.263°,was synthesized under a pressure of 4~GPa at a temperature between 1100℃and 1200℃.The structure ofα-MoP_(2) and its relationship to other transition metal diphosphides are discussed.Surprisingly,the ambient pressure phase orthorhombicβ-MoP_(2)(space group Cmc21)is denser in structure thanα-MoP_(2).Room-temperature high-pressure x-ray diffraction studies exclude the possibility of phase transition fromβ-MoP_(2) to α-MoP_(2),suggesting thatα-MoP_(2) is a stable phase at ambient conditions;this is also supported by the total energy and phonon calculations.展开更多
To thoroughly study the extinguishing effect of a high-pressure water mist fire extinguishing system when a transformer fire occurs,a 3D experimental model of a transformer is established in this work by employing Fir...To thoroughly study the extinguishing effect of a high-pressure water mist fire extinguishing system when a transformer fire occurs,a 3D experimental model of a transformer is established in this work by employing Fire Dynamics Simulator(FDS)software.More specifically,by setting different parameters,the process of the highpressure water mist fire extinguishing system with the presence of both diverse ambient temperatures and water mist sprinkler laying conditions is simulated.In addition,the fire extinguishing effect of the employed high-pressure water mist system with the implementation of different strategies is systematically analyzed.The extracted results show that a fire source farther away fromthe centerline leads to a lower local temperature distribution.In addition,as the ambient temperature increases,the temperature above the fire source decreases,while the temperature and the concentrationof theupperflue gas layer bothdecrease.Interestingly,after thehigh-pressurewatermist sprinkler begins to operate,both the temperature distribution above the fire source and the concentration of the flue gas decrease,which indicates that the high-pressure water mist system plays the role of cooling and dust removal.By comparing various sprinkler laying methods,it is found that the lower sprinkler height has a better effect on the temperature above the fire source,the temperature of the upper flue gas layer,and the concentration of the flue gas.Moreover,when the sprinkler is spread over thewhole transformer,the cooling effect on both the temperature above the fire source and the temperature of the upper flue gas layer is good,whereas the change in the concentration of the flue gas above the fire source is not obvious compared to the case where the sprinkler is not fully spread.展开更多
The high-pressure diagram of V–N compounds is enriched by proposed seven new stable high-pressure phases.The P-1-VN_4with the armchair N-rich structure may be quenched to ambient conditions.The formed N–N covalent b...The high-pressure diagram of V–N compounds is enriched by proposed seven new stable high-pressure phases.The P-1-VN_4with the armchair N-rich structure may be quenched to ambient conditions.The formed N–N covalent bond plays an important role for the structural stability of N-chain.The charge transfer results in a V–N ionic bond interaction,which further improves the stability of N-chain structure.The P-1-VN_4,P4mnc-VN_8,and Immm-VN_(10)with the outstanding detonation properties have potential application in explosive field.展开更多
We report the discovery of TiO_(2)-Ⅱ in the unmelted rock of the shocked Suizhou L6 chondrite.Natural TiO_(2)-Ⅱ was previously found in ultrahigh-pressure metamorphic and mantle-derived rocks,terrestrial impact stru...We report the discovery of TiO_(2)-Ⅱ in the unmelted rock of the shocked Suizhou L6 chondrite.Natural TiO_(2)-Ⅱ was previously found in ultrahigh-pressure metamorphic and mantle-derived rocks,terrestrial impact structures,and tektite.Our microscopic,Raman spectroscopic,electron microprobe and transmission electron microscopic investigations have revealed:(1) All observed TiO_(2)-Ⅱ grains are related with ilmenite and pyrophanite;(2) TiO_(2)-Ⅱ occurs as needle-and leaf-shaped inclusions in llmenite and patch-,tape-shaped body in pyrophanite;(3)The composition of TiO_(2)-Ⅱ is identical with that of its precursor rutile;(4) The Raman spectrum of TiO_(2)-Ⅱ is in good agreement with that of natural and synthesized α-PbO_(2)-type TiO_(2);(5) TiO_(2)-Ⅱ occurs mainly in the form of well-ordered nano-domains and small mis-orientation among the domains can be observed.(6) All electron diffraction reflections from TiO_(2)-Ⅱ can be indexed to α-PbO_(2)structure in space group Pbcn with lattice parameters of a=4.481 ?,b=5.578 A and c=4.921 A;(7) The exsolution inclusions of rutile from host ilmenite are mostly connected with an alternation process along the lamellar twinning plane of ilmenite induced by shockinduced high pressure and high temperature;(8) The P-T regime of 20-25 GPa and 1000 ℃ estimated for the Suizhou unmelted rock is suitable for phase transition of rutile into TiO_(2)-Ⅱ phase.展开更多
Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The ...Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The results indicated that the average grain sizes were refined forming gradient structure with increasing specimen radial position from center(12.2-5.4μm),and that the initial basal texture intensity of the extruded magnesium alloy was weakened from 46.2 to 8.3.Furthermore,the extension twins(ETs)could be disintegrated from the twins forming separated twins with smaller sizes.Interestingly,ETs with the same twin variant intersecting with each other could be coalesced forming grains with similar orientation,while ETs with different twin variants were separated by twins boundaries contributing to grain refinement.Moreover,in addition to the conventional continuous dynamic recrystallized(CDRX)grains with 30˚orientation rotated around C-axis of the parent grains,CDRXed grains with 30˚rotation around a-axis and random rotation axis were also discerned.Besides,the CDRX evolution induced twins were also elaborated,exhibiting the complex competition between CDRX and twining.Hot torsion deformation with constant decreasing temperatures rate is an effective way of grain refinement and texture modification.展开更多
BACKGROUND Testicular torsion is the most common acute scrotum worldwide and mainly occurs in children and adolescents.Studies have demonstrated that the duration of symptoms and torsion grade lead to different outcom...BACKGROUND Testicular torsion is the most common acute scrotum worldwide and mainly occurs in children and adolescents.Studies have demonstrated that the duration of symptoms and torsion grade lead to different outcomes in children diagnosed with testicular torsion.AIM To predict the possibility of testicular salvage(TS)in patients with testicular torsion in a tertiary center.METHODS We reviewed the charts of 75 pediatric patients with acute testicular torsion during a 12-year period from November 2011 to July 2023 at the Suzhou Hospital of Anhui Medical University.Univariate and multivariate logistic regression analyses were used to determine independent predictors of testicular torsion.The data included clinical findings,physical examinations,laboratory data,color Doppler ultrasound findings,operating results,age,presenting institution status,and follow-up results.RESULTS Our study included 75 patients.TS was possible in 57.3%of all patients;testicular torsion occurred mostly in winter,and teenagers aged 11-15 years old accounted for 60%.Univariate logistic regression analyses revealed that younger age(P=0.09),body mass index(P=0.004),torsion angle(P=0.013),red blood cell count(P=0.03),neutrophil-to-lymphocyte ratio(P=0.009),and initial presenting institution(P<0.001)were associated with orchiectomy.In multivariate analysis,only the initial presenting institution predicted TS(P<0.05).CONCLUSION The initial presenting institution has a predictive value for predicting TS in patients with testicular torsion.Children with scrotal pain should be admitted to a tertiary hospital as soon as possible.展开更多
Purpose – This study aims to reduce the redundant weight of the anti-roll torsion bar brought by thetraditional empirical design and improving its strength and stiffness.Design/methodology/approach – Based on the fi...Purpose – This study aims to reduce the redundant weight of the anti-roll torsion bar brought by thetraditional empirical design and improving its strength and stiffness.Design/methodology/approach – Based on the finite element approach coupled with the improved belugawhale optimization (IBWO) algorithm, a collaborative optimization method is suggested to optimize the designof the anti-roll torsion bar structure and weight. The dimensions and material properties of the torsion bar weredefined as random variables, and the torsion bar’s mass and strength were investigated using finite elements.Then, chaotic mapping and differential evolution (DE) operators are introduced to improve the beluga whaleoptimization (BWO) algorithm and run case studies.Findings – The findings demonstrate that the IBWO has superior solution set distribution uniformity,convergence speed, solution correctness and stability than the BWO. The IBWO algorithm is used to optimizethe anti-roll torsion bar design. The error between the optimization and finite element simulation results wasless than 1%. The weight of the optimized anti-roll torsion bar was lessened by 4%, the maximum stress wasreduced by 35% and the stiffness was increased by 1.9%.Originality/value – The study provides a methodological reference for the simulation optimization process ofthe lateral anti-roll torsion bar.展开更多
BACKGROUND Cystic lymphangioma is a rare benign tumor that affects the lymphatic system.Mesenteric lymphangiomas in the small bowel are extremely uncommon.CASE SUMMARY We present a 21-year-old female patient who compl...BACKGROUND Cystic lymphangioma is a rare benign tumor that affects the lymphatic system.Mesenteric lymphangiomas in the small bowel are extremely uncommon.CASE SUMMARY We present a 21-year-old female patient who complained of abdominal pain.The diagnosis of ovarian torsion was suspected after abdominopelvic unenhanced computed tomography and ultrasound revealed a large cyst in contact with the bladder,ovary,and uterus.The patient underwent emergency laparotomy per-formed by gynecologists,but it was discovered that the cystic tumor originated from the jejunum.Gastrointestinal surgeons were then called in to perform a cystectomy.Pathological examination confirmed the diagnosis of cystic lymphangioma of the mesentery.The patient had an uneventful postoperative recovery.CONCLUSION Mesenteric lymphangiomas can cause abdominal pain,and imaging techniques can help determine their characteristics,location,and size.Complete surgical excision and pathological examination are considered the standard treatment and diagnostic method.展开更多
Aspects of the general Vlasov theory are examined separately as applied to a thin-walled channel section cantilever beam under free-end end loading. In particular, the flexural bending and shear that arise under trans...Aspects of the general Vlasov theory are examined separately as applied to a thin-walled channel section cantilever beam under free-end end loading. In particular, the flexural bending and shear that arise under transverse shear and axial torsional loading are each considered theoretically. These analyses involve the location of the shear centre at which transverse shear forces when applied do not produce torsion. This centre, when taken to be coincident with the centre of twist implies an equivalent reciprocal behaviour. That is, an axial torsion applied concentric with the shear centre will twist but not bend the beam. The respective bending and shear stress conversions are derived for each action applied to three aluminium alloy extruded channel sections mounted as cantilevers with a horizontal principal axis of symmetry. Bending and shear are considered more generally for other thin-walled sections when the transverse loading axes at the shear centre are not parallel to the section = s centroidal axes of principal second moments of area. The fixing at one end of the cantilever modifies the St Venant free angular twist and the free warping displacement. It is shown from the Wagner-Kappus torsion theory how the end constrained warping generates an axial stress distribution that varies with the length and across the cross-section for an axial torsion applied to the shear centre. It should be mentioned here for wider applications and validation of the Vlasov theory that attendant papers are to consider in detail bending and torsional loadings applied to other axes through each of the centroid and the web centre. Therein, both bending and twisting arise from transverse shear and axial torsion applied to each position being displaced from the shear centre. Here, the influence of the axis position upon the net axial and shear stress distributions is to be established. That is, the net axial stress from axial torsional loading is identified with the sum of axial stress due to bending and axial stress arising from constrained warping displacements at the fixing. The net shear stress distribution overlays the distributions from axial torsion and that from flexural shear under transverse loading. Both arise when transverse forces are displaced from the shear centre.展开更多
A large-scale high-pressure granulite belt (HPGB), more than 700 km long, is recognized within the metamorphic basement of the North China craton. In the regional tectonic framework, the Hengshan-Chengde HPGB is locat...A large-scale high-pressure granulite belt (HPGB), more than 700 km long, is recognized within the metamorphic basement of the North China craton. In the regional tectonic framework, the Hengshan-Chengde HPGB is located in the central collision belt between the western block and eastern block, and represents the deep crustal structural level. The typical high-pressure granulite (HPG) outcrops are distributed in the Hengshan and Chengde areas. HPGs commonly occur as mafic xenoliths within ductile shear zones, and underwent multipile deformations. To the south, the Hengshan-Chengde HPGB is juxtaposed with the Wutai greenstone belt by several strike-slip shear zones. Preliminary isotopic age dating indicates that HPGs from North China were mainly generated at the end of the Neoarchaean, assocaited with tectonic assembly of the western and eastern blocks.展开更多
The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained...The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.展开更多
The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages i...The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content (10%) of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.展开更多
High-pressure (HP) granulites widely occur as enclaves within tonalite-trondhjemite- granodiorite (TTG) gneisses of the Early Precambrian metamorphic basement in the Shandong Peninsula, southeast part of the North...High-pressure (HP) granulites widely occur as enclaves within tonalite-trondhjemite- granodiorite (TTG) gneisses of the Early Precambrian metamorphic basement in the Shandong Peninsula, southeast part of the North China Craton (NCC). Based on cathodoluminescence (CL), laser Raman spec- troscopy and in-situ U-Pb dating, we characterize the zircons from the HP granulites and group them into three main types: inherited (magmatic) zircon, HP metamorphic zircon and retrograde zircon. The inher- ited zircons with clear or weakly defined magmatic zoning contain inclusions of apatites, and 207pb/206pb ages of 2915--2890 Ma and 2763--2510 Ma, correlating with two magmatic events in the Archaean base- ment. The homogeneous HP metamorphic zircons contain index minerals of high-pressure metamor- phism including garnet, clinopyroxene, plagioclase, quartz, rutile and apatite, and yield 207pb/2066pb ages between 1900 and 1850 Ma, marking the timing of peak HP granulite facies metamorphism. The retrograde zircons contain inclusions of orthopyroxene, plagioclase, quartz, apatite and amphibole, and yield the youngest 207pb/206pb ages of 1840-1820 Ma among the three groups, which we correlate to the medium to low-pressure granulite facies retrograde metamorphism. The data presented in this study suggest subduction of Meso- and Neoarchean magmatic protoliths to lower crust depths where they were subjected to HP granulite facies metamorphism during Palaeoproterozoic (1900-1850 Ma). Subse- quently, the HP granulites were exhumated to upper crust levels, and were ovel-printed by medium to low-pressure granulite and amphibolite facies retrograde event at ca. 1840--820 Ma.展开更多
Using the single—zircon evaporation technique and U—Pb method, the authors have conducted an isotope geochonological study of the Huilanshan granulite and Shima garnet-bearing plagioclase gneiss (“country rocks” o...Using the single—zircon evaporation technique and U—Pb method, the authors have conducted an isotope geochonological study of the Huilanshan granulite and Shima garnet-bearing plagioclase gneiss (“country rocks” of the Shima eclogite) in the Dabie Mountains. The study shows that these rocks have peak metamorphic ages of 443–455 Ma, which are essentially consistent with that of the Caledonian high—ultrahigh pressure eclogites. This indicates the existence of the Caledonian collisional orogeny in the Dabie Mountains.展开更多
This paper puts forward using high-pressure water jet technology to control rock burst in roadway, and analyzes the theory of controlling rock burst in roadway by the weak structure zone model. The weak structure zone...This paper puts forward using high-pressure water jet technology to control rock burst in roadway, and analyzes the theory of controlling rock burst in roadway by the weak structure zone model. The weak structure zone is formed by using high-pressure water jet to cut the coal wall in a continuous and rotational way. In order to study the influence law of weak structure zone in surrounding rock, this paper numerically analyzed the influence law of weak structure zone, and the disturbance law of coal wall and floor under dynamic and static combined load. The results show that when the distance between high-pressure water jet drillings is 3 m and the diameter of drilling is 300 mm, continuous stress superposition zone can be formed. The weak structure zone can transfer and reduce the concentrated static load in surrounding rock, and then form distressed zone. The longer the high-pressure water jet drilling is, the larger the distressed zone is. The stress change and displacement change of non-distressed zone in coal wall and floor are significantly greater than that of distressed zone under dynamic and static combined load. And it shows that the distressed zone can effectively control rock burst in roadway under dynamic and static combined load. High-pressure water jet technology was applied in the haulage gate of 250203 working face in Yanbei Coal Mine, and had gained good effect. The study conclusions provide theoretical foundation and a new guidance for controlling rock burst in roadway.展开更多
基金sponsored by the National Natural Science Foundation of China ( 51571150,11572222)Tianjin Natural Science Foundation ( 14JCYBJC16900)
文摘Recently,magnesium and its alloys have attracted more and more attention as promising implant materials due to their excellent properties such as good biocompatibility,biodegradation,non-toxicity and comparable mechanical properties with natural bone.They can be gradually degraded and absorbed so as to avoid the second surgery for implants removal after the tissues are healed completely.In addition,they are also able to prevent the stress shielding effect in human body environment because of the density,elastic modulus and yield strength of magnesium closer to the bone.Unfortunately,the high corrosion rate which causes early mechanical failure of the implants in physiological environment limits the widespread use of magnesium alloys for clinical application in biology.And the high corrosion process usually causes huge hydrogen evolution and alkalinization,resulting in problems against the implants as well as the surrounding tissues.In order to enhance the corrosion resistance of magnesium alloys,in this study,the ZEK100 magnesium alloy was pre-deformed with a highpressure torsion(HPT)process and then fabricated hydroxyapatite(HA)coatings with different contents of Mg(OH)2 nanopowder via hydrothermal method.The specimens were characterized by scanning electron microscope(SEM)and X-ray diffraction(XRD).At the same time,prior and after the HPT procedure,the metallography,microhardness and tensile tests of specimens were characterized.Meanwhile,the corrosion behavior of the specimens was evaluated by electrochemical impedance spectroscopy(EIS)and hydrogen evolution tests.And the interface bonding strength of the HA coating on the magnesium alloy substrate was evaluated by a tape adhesion test/scratch test.Results showed that HPT processing refined the grain size and introduced a great number of twins,resulting in the enhancement of microhardness and Young’s modulus of ZEK100 magnesium alloy,but hardness values at the edge were higher than those at the center due to the uneven shear strain.At the same conditions,the HA coating on HPT-ZEK was denser,thicker than that on ZEK sample and the crystal sizes of HA were smaller on HPT-ZEK.These were attributed to fine,uniform distributed secondary phases and lots of fine grains,twins,grain boundaries in HPT-ZEK substrates which can provide more nucleation sites for the HA crystal.In terms of the amount of Mg(OH)2 nanopowder,Mg(OH)2 nanopowder significantly influenced the microstructure and thickness of the HA coating.And at a 0.3 mg/mL content of Mg(OH)2 nanopowder,there was the densest,thickest HA coating on magnesium alloys,and the crystal size of HA was minimum.Specifically,the HA coating thickness on ZEK-03(0.3 mg/mL Mg(OH)2 nanopowder)was 1.8 times of that on ZEK-00(0 mg/mL Mg(OH)2 nanopowder),while the HA coating thickness on HPT-03 was 2.6 times of that on ZEK-00.And the adhesion strength of HA coating on HPT-03 substrate was better than that on ZEK-03.In addition,HPT technology and surface modification by HA coating simultaneously increased the corrosion resistance of ZEK100 magnesium alloy and the corrosion of HPT-ZEK samples occurred in a more uniform manner,while it was pitting on the surface of ZEK100 magnesium alloy.Therefore,there was the best corrosion resistance on HPT-03 sample,which could promote the application of magnesium alloys in biomedical fields.
文摘Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necessary strength.Therefore,the experiments and analytical solutions presented in this paper are performed according to the relevant standards and codes,including ASME PCC-2,ASME B31.8S,ASME B31.4,ISO 24817 and ASME B31.G.In addition,the experimental tests are replicated numerically using the finite element method.Setting the strain gauges at different distances from the defect location,can reduce the nonlinear effects,deformation,and fluctuations due to the high pressure.The direct relationship between the depth of an axial defect and the stress concentration is observed at the inner side edges of the defect.Composite reparation reduces the non-linearities related to the sharp variation of the geometry and a more reliable numerical simulation could be performed.
基金supported by National Key R&D Program of China[grant number 2017YFE0123500]National Natural Science Foundation of China[grant number 51971072,51671064]+2 种基金the Fundamental Research Funds for the Central University[grant number HEUCFG201836]the support from the RFBR-CNPq-DST research project№19-58-80018the support in part from the Russian Foundation for Basic Research(project No.20-03-00614)。
文摘High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase and retained nanocrystalline;second is the alternating bands of amorphous phase and high defect density crystalline.As a result,post deformation annealing(PDA)at 500-700℃leads to the non-uniform distribution of martensite and parent phase grains.The grains of martensite are twice larger compared to that of parent phase.The nanocrystalline and ultrafine grains form after annealing at 500-600℃and 700℃,respectively.The twinning mechanism does not change with the reduction of martensitic grains up to^35 nm.The relationship between strength and grain size in Ti29.7Ni50.3Hf20 alloy obeys the classical Hall-Petch relationship with a coefficient of 10.80±0.39 GPa nm^1/2.
文摘The wear characteristics of Cu and Cu-SiC composite microsize powders consolidated by cold compaction combined with sintering or high-pressure torsion(HPT)were investigated.The HPT processed(HPTed)samples with bimodal and trimodal microstructures and fine Cu grains and SiC particle sizes have superior hardness,reasonable ductility level,and high wear resistance.The wear mass loss and coefficient of friction of HPTed samples were remarkably lower than that of cold-compacted and sintered samples as well as that of micro and nano Cu and Cu-SiC composites from previous studies.The sample fabrication method has an apparent influence on the wear mechanism.The wear mechanism was converted from adhesive,delamination,three-body mechanism,grooves(take off the SiC particles),and cracks into abrasive wear after HPT.Oxidization can be considered a dominant wear mechanism in all cases.The worn surface morphology and analysis support the relationship between wear mechanism and characteristics.
基金supported by the National Natural Science Foundation of China (Grant Nos.10721202,10772178,50571110)
文摘Cu samples were subjected to high-pressure torsion (HPT) with up to 6 turns at room temperature (RT) and liquid nitrogen temperature (LNT),respectively.The effects of temperature on grain refinement and microhardness variation were investigated.For the samples after HPT processing at RT,the grain size reduced from 43 μm to 265 nm,and the Vickers microhardness increased from HV52 to HV140.However,for the samples after HPT processing at LNT,the value of microhardness reached its maximum of HV150 near the center of the sample and it decreased to HV80 at the periphery region.Microstructure observations revealed that HPT straining at LNT induced lamellar structures with thickness less than 100 nm appearing near the central region of the sample,but further deformation induced an inhomogeneous distribution of grain sizes,with submicrometer-sized grains embedded inside micrometer-sized grains.The submicrometer-sized grains with high dislocation density indicated their nonequilibrium nature.On the contrary,the micrometer-sized grains were nearly free of dislocation,without obvious deformation trace remaining in them.These images demonstrated that the appearance of micrometer-sized grains is the result of abnormal grain growth of the deformed fine grains.
基金Project supported by the National Natural Science Foundation of China (Grant Nos.92065201,11874264,and 11974154)the Starting Grant of ShanghaiTech University and Analytical Instrumentation Center,SPST,ShanghaiTech University (Grant No.SPST-AIC10112914)support from the Natural Science Foundation of Shandong Province,China (Grant No.ZR2022MA004)。
文摘Monoclinicα-MoP_(2),with the OsGe2-type structure(space group C2/m,Z=4)and lattice parameters a=8.7248(11)Å,b=3.2322(4)Å,c=7.4724(9)Å,andβ=119.263°,was synthesized under a pressure of 4~GPa at a temperature between 1100℃and 1200℃.The structure ofα-MoP_(2) and its relationship to other transition metal diphosphides are discussed.Surprisingly,the ambient pressure phase orthorhombicβ-MoP_(2)(space group Cmc21)is denser in structure thanα-MoP_(2).Room-temperature high-pressure x-ray diffraction studies exclude the possibility of phase transition fromβ-MoP_(2) to α-MoP_(2),suggesting thatα-MoP_(2) is a stable phase at ambient conditions;this is also supported by the total energy and phonon calculations.
基金supported by Science and Technology Projects Funded by State Grid Corporation of China (5200202024105A0000).
文摘To thoroughly study the extinguishing effect of a high-pressure water mist fire extinguishing system when a transformer fire occurs,a 3D experimental model of a transformer is established in this work by employing Fire Dynamics Simulator(FDS)software.More specifically,by setting different parameters,the process of the highpressure water mist fire extinguishing system with the presence of both diverse ambient temperatures and water mist sprinkler laying conditions is simulated.In addition,the fire extinguishing effect of the employed high-pressure water mist system with the implementation of different strategies is systematically analyzed.The extracted results show that a fire source farther away fromthe centerline leads to a lower local temperature distribution.In addition,as the ambient temperature increases,the temperature above the fire source decreases,while the temperature and the concentrationof theupperflue gas layer bothdecrease.Interestingly,after thehigh-pressurewatermist sprinkler begins to operate,both the temperature distribution above the fire source and the concentration of the flue gas decrease,which indicates that the high-pressure water mist system plays the role of cooling and dust removal.By comparing various sprinkler laying methods,it is found that the lower sprinkler height has a better effect on the temperature above the fire source,the temperature of the upper flue gas layer,and the concentration of the flue gas.Moreover,when the sprinkler is spread over thewhole transformer,the cooling effect on both the temperature above the fire source and the temperature of the upper flue gas layer is good,whereas the change in the concentration of the flue gas above the fire source is not obvious compared to the case where the sprinkler is not fully spread.
文摘The high-pressure diagram of V–N compounds is enriched by proposed seven new stable high-pressure phases.The P-1-VN_4with the armchair N-rich structure may be quenched to ambient conditions.The formed N–N covalent bond plays an important role for the structural stability of N-chain.The charge transfer results in a V–N ionic bond interaction,which further improves the stability of N-chain structure.The P-1-VN_4,P4mnc-VN_8,and Immm-VN_(10)with the outstanding detonation properties have potential application in explosive field.
文摘We report the discovery of TiO_(2)-Ⅱ in the unmelted rock of the shocked Suizhou L6 chondrite.Natural TiO_(2)-Ⅱ was previously found in ultrahigh-pressure metamorphic and mantle-derived rocks,terrestrial impact structures,and tektite.Our microscopic,Raman spectroscopic,electron microprobe and transmission electron microscopic investigations have revealed:(1) All observed TiO_(2)-Ⅱ grains are related with ilmenite and pyrophanite;(2) TiO_(2)-Ⅱ occurs as needle-and leaf-shaped inclusions in llmenite and patch-,tape-shaped body in pyrophanite;(3)The composition of TiO_(2)-Ⅱ is identical with that of its precursor rutile;(4) The Raman spectrum of TiO_(2)-Ⅱ is in good agreement with that of natural and synthesized α-PbO_(2)-type TiO_(2);(5) TiO_(2)-Ⅱ occurs mainly in the form of well-ordered nano-domains and small mis-orientation among the domains can be observed.(6) All electron diffraction reflections from TiO_(2)-Ⅱ can be indexed to α-PbO_(2)structure in space group Pbcn with lattice parameters of a=4.481 ?,b=5.578 A and c=4.921 A;(7) The exsolution inclusions of rutile from host ilmenite are mostly connected with an alternation process along the lamellar twinning plane of ilmenite induced by shockinduced high pressure and high temperature;(8) The P-T regime of 20-25 GPa and 1000 ℃ estimated for the Suizhou unmelted rock is suitable for phase transition of rutile into TiO_(2)-Ⅱ phase.
基金supported by key technology research and development project of ShanXi province(20201102019)Natural science foundation of Shanxi Province(201901D111167)+2 种基金Shanxi Scholarship Council of China(2020-117)JCKY2018408B003Magnesium alloy high-performance XXX multi-directional extrusion technologyXX supporting scientific research project(xxxx-2019-021).
文摘Hot torsion tests for AZ80 magnesium alloy were carried out in the temperature range of 380℃-260℃,with a constant decreasing temperature rate of 10℃/s in order to weaken the basal texture and refine the grains.The results indicated that the average grain sizes were refined forming gradient structure with increasing specimen radial position from center(12.2-5.4μm),and that the initial basal texture intensity of the extruded magnesium alloy was weakened from 46.2 to 8.3.Furthermore,the extension twins(ETs)could be disintegrated from the twins forming separated twins with smaller sizes.Interestingly,ETs with the same twin variant intersecting with each other could be coalesced forming grains with similar orientation,while ETs with different twin variants were separated by twins boundaries contributing to grain refinement.Moreover,in addition to the conventional continuous dynamic recrystallized(CDRX)grains with 30˚orientation rotated around C-axis of the parent grains,CDRXed grains with 30˚rotation around a-axis and random rotation axis were also discerned.Besides,the CDRX evolution induced twins were also elaborated,exhibiting the complex competition between CDRX and twining.Hot torsion deformation with constant decreasing temperatures rate is an effective way of grain refinement and texture modification.
基金Supported by Anhui Province Translational Medicine Research Fund Project,No.2021zhyx-C59 and No.2021zhyx-C75.
文摘BACKGROUND Testicular torsion is the most common acute scrotum worldwide and mainly occurs in children and adolescents.Studies have demonstrated that the duration of symptoms and torsion grade lead to different outcomes in children diagnosed with testicular torsion.AIM To predict the possibility of testicular salvage(TS)in patients with testicular torsion in a tertiary center.METHODS We reviewed the charts of 75 pediatric patients with acute testicular torsion during a 12-year period from November 2011 to July 2023 at the Suzhou Hospital of Anhui Medical University.Univariate and multivariate logistic regression analyses were used to determine independent predictors of testicular torsion.The data included clinical findings,physical examinations,laboratory data,color Doppler ultrasound findings,operating results,age,presenting institution status,and follow-up results.RESULTS Our study included 75 patients.TS was possible in 57.3%of all patients;testicular torsion occurred mostly in winter,and teenagers aged 11-15 years old accounted for 60%.Univariate logistic regression analyses revealed that younger age(P=0.09),body mass index(P=0.004),torsion angle(P=0.013),red blood cell count(P=0.03),neutrophil-to-lymphocyte ratio(P=0.009),and initial presenting institution(P<0.001)were associated with orchiectomy.In multivariate analysis,only the initial presenting institution predicted TS(P<0.05).CONCLUSION The initial presenting institution has a predictive value for predicting TS in patients with testicular torsion.Children with scrotal pain should be admitted to a tertiary hospital as soon as possible.
基金funded by the National Natural Science Foundation of China(No:51875073)China RAILWAY(No:K2021J042).
文摘Purpose – This study aims to reduce the redundant weight of the anti-roll torsion bar brought by thetraditional empirical design and improving its strength and stiffness.Design/methodology/approach – Based on the finite element approach coupled with the improved belugawhale optimization (IBWO) algorithm, a collaborative optimization method is suggested to optimize the designof the anti-roll torsion bar structure and weight. The dimensions and material properties of the torsion bar weredefined as random variables, and the torsion bar’s mass and strength were investigated using finite elements.Then, chaotic mapping and differential evolution (DE) operators are introduced to improve the beluga whaleoptimization (BWO) algorithm and run case studies.Findings – The findings demonstrate that the IBWO has superior solution set distribution uniformity,convergence speed, solution correctness and stability than the BWO. The IBWO algorithm is used to optimizethe anti-roll torsion bar design. The error between the optimization and finite element simulation results wasless than 1%. The weight of the optimized anti-roll torsion bar was lessened by 4%, the maximum stress wasreduced by 35% and the stiffness was increased by 1.9%.Originality/value – The study provides a methodological reference for the simulation optimization process ofthe lateral anti-roll torsion bar.
文摘BACKGROUND Cystic lymphangioma is a rare benign tumor that affects the lymphatic system.Mesenteric lymphangiomas in the small bowel are extremely uncommon.CASE SUMMARY We present a 21-year-old female patient who complained of abdominal pain.The diagnosis of ovarian torsion was suspected after abdominopelvic unenhanced computed tomography and ultrasound revealed a large cyst in contact with the bladder,ovary,and uterus.The patient underwent emergency laparotomy per-formed by gynecologists,but it was discovered that the cystic tumor originated from the jejunum.Gastrointestinal surgeons were then called in to perform a cystectomy.Pathological examination confirmed the diagnosis of cystic lymphangioma of the mesentery.The patient had an uneventful postoperative recovery.CONCLUSION Mesenteric lymphangiomas can cause abdominal pain,and imaging techniques can help determine their characteristics,location,and size.Complete surgical excision and pathological examination are considered the standard treatment and diagnostic method.
文摘Aspects of the general Vlasov theory are examined separately as applied to a thin-walled channel section cantilever beam under free-end end loading. In particular, the flexural bending and shear that arise under transverse shear and axial torsional loading are each considered theoretically. These analyses involve the location of the shear centre at which transverse shear forces when applied do not produce torsion. This centre, when taken to be coincident with the centre of twist implies an equivalent reciprocal behaviour. That is, an axial torsion applied concentric with the shear centre will twist but not bend the beam. The respective bending and shear stress conversions are derived for each action applied to three aluminium alloy extruded channel sections mounted as cantilevers with a horizontal principal axis of symmetry. Bending and shear are considered more generally for other thin-walled sections when the transverse loading axes at the shear centre are not parallel to the section = s centroidal axes of principal second moments of area. The fixing at one end of the cantilever modifies the St Venant free angular twist and the free warping displacement. It is shown from the Wagner-Kappus torsion theory how the end constrained warping generates an axial stress distribution that varies with the length and across the cross-section for an axial torsion applied to the shear centre. It should be mentioned here for wider applications and validation of the Vlasov theory that attendant papers are to consider in detail bending and torsional loadings applied to other axes through each of the centroid and the web centre. Therein, both bending and twisting arise from transverse shear and axial torsion applied to each position being displaced from the shear centre. Here, the influence of the axis position upon the net axial and shear stress distributions is to be established. That is, the net axial stress from axial torsional loading is identified with the sum of axial stress due to bending and axial stress arising from constrained warping displacements at the fixing. The net shear stress distribution overlays the distributions from axial torsion and that from flexural shear under transverse loading. Both arise when transverse forces are displaced from the shear centre.
文摘A large-scale high-pressure granulite belt (HPGB), more than 700 km long, is recognized within the metamorphic basement of the North China craton. In the regional tectonic framework, the Hengshan-Chengde HPGB is located in the central collision belt between the western block and eastern block, and represents the deep crustal structural level. The typical high-pressure granulite (HPG) outcrops are distributed in the Hengshan and Chengde areas. HPGs commonly occur as mafic xenoliths within ductile shear zones, and underwent multipile deformations. To the south, the Hengshan-Chengde HPGB is juxtaposed with the Wutai greenstone belt by several strike-slip shear zones. Preliminary isotopic age dating indicates that HPGs from North China were mainly generated at the end of the Neoarchaean, assocaited with tectonic assembly of the western and eastern blocks.
基金financially supported by the Research and Development Institute, Silpakorn University
文摘The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.
基金support from Subtopics of National Science and Technology Major Project(2011ZX05026-004-03)the National Natural Science Foundation of China (51104167)
文摘The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content (10%) of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.
基金supported by National Program on Key Basic Research Project(973 Program) (Grant No.2012CB416603)the National Natural Science Foundation of China(Grant Nos.40725007 and 40921001)the China Geological Survey Program(Grant Nos.1212011120150 and 1212010811065)
文摘High-pressure (HP) granulites widely occur as enclaves within tonalite-trondhjemite- granodiorite (TTG) gneisses of the Early Precambrian metamorphic basement in the Shandong Peninsula, southeast part of the North China Craton (NCC). Based on cathodoluminescence (CL), laser Raman spec- troscopy and in-situ U-Pb dating, we characterize the zircons from the HP granulites and group them into three main types: inherited (magmatic) zircon, HP metamorphic zircon and retrograde zircon. The inher- ited zircons with clear or weakly defined magmatic zoning contain inclusions of apatites, and 207pb/206pb ages of 2915--2890 Ma and 2763--2510 Ma, correlating with two magmatic events in the Archaean base- ment. The homogeneous HP metamorphic zircons contain index minerals of high-pressure metamor- phism including garnet, clinopyroxene, plagioclase, quartz, rutile and apatite, and yield 207pb/2066pb ages between 1900 and 1850 Ma, marking the timing of peak HP granulite facies metamorphism. The retrograde zircons contain inclusions of orthopyroxene, plagioclase, quartz, apatite and amphibole, and yield the youngest 207pb/206pb ages of 1840-1820 Ma among the three groups, which we correlate to the medium to low-pressure granulite facies retrograde metamorphism. The data presented in this study suggest subduction of Meso- and Neoarchean magmatic protoliths to lower crust depths where they were subjected to HP granulite facies metamorphism during Palaeoproterozoic (1900-1850 Ma). Subse- quently, the HP granulites were exhumated to upper crust levels, and were ovel-printed by medium to low-pressure granulite and amphibolite facies retrograde event at ca. 1840--820 Ma.
基金This study was supported by the National Natural Science Foundation of China grants 49572146 and 49772147 and the Foundation for Development of Science and Technology in Geology grant 9514.
文摘Using the single—zircon evaporation technique and U—Pb method, the authors have conducted an isotope geochonological study of the Huilanshan granulite and Shima garnet-bearing plagioclase gneiss (“country rocks” of the Shima eclogite) in the Dabie Mountains. The study shows that these rocks have peak metamorphic ages of 443–455 Ma, which are essentially consistent with that of the Caledonian high—ultrahigh pressure eclogites. This indicates the existence of the Caledonian collisional orogeny in the Dabie Mountains.
基金supported by the National Natural Science Foundation of China (Nos. 51574243, 51404269)the Fundamental Research Funds for the Central Universities of China (No. 2014XT01)+1 种基金Guizhou Science and Technology Foundation of China (No. 20152072)the Priority Academic Program Development of Jiangsu Higher Education Institutions, China (No. SZBF2011-6B35)
文摘This paper puts forward using high-pressure water jet technology to control rock burst in roadway, and analyzes the theory of controlling rock burst in roadway by the weak structure zone model. The weak structure zone is formed by using high-pressure water jet to cut the coal wall in a continuous and rotational way. In order to study the influence law of weak structure zone in surrounding rock, this paper numerically analyzed the influence law of weak structure zone, and the disturbance law of coal wall and floor under dynamic and static combined load. The results show that when the distance between high-pressure water jet drillings is 3 m and the diameter of drilling is 300 mm, continuous stress superposition zone can be formed. The weak structure zone can transfer and reduce the concentrated static load in surrounding rock, and then form distressed zone. The longer the high-pressure water jet drilling is, the larger the distressed zone is. The stress change and displacement change of non-distressed zone in coal wall and floor are significantly greater than that of distressed zone under dynamic and static combined load. And it shows that the distressed zone can effectively control rock burst in roadway under dynamic and static combined load. High-pressure water jet technology was applied in the haulage gate of 250203 working face in Yanbei Coal Mine, and had gained good effect. The study conclusions provide theoretical foundation and a new guidance for controlling rock burst in roadway.