Exceptional reversed yield strength asymmetry in a rare-earth free Mg alloy containing quasicrystal precipitates

This work reports an exceptional reversed yield strength asymmetry at room temperature for a rare-earth free magnesium alloy containing a mass of fine dispersed quasicrystal(I-phase)precipitates.Although exhibiting traditional basal texture,it owns an exceptional CYS/TYS as high as~1.17.Electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM)examinations indicate pyramidal and prismatic dislocations plus tensile twinning being activated after immediate yielding in compression while basal and non-basal dislocations in tension.I-phase particles transferred the concentrated stress by self-twinning to provide the driving force for tensile twin initiating in neighboring grains,thereby significantly increasing the critical resolved shear stress of tensile twinning to possibly the level of pyramidal slip,finally leading to the dominance of pyramidal slip plus tensile twinning in texture grains.This results in a higher contribution on yield strength by~55 MPa in compression than in tension,which reasonably agrees with the experimental yield strength difference(~38 MPa).It can be concluded that I-phase particles influence deformation modes in tension and in compression,finally result in reversed yield strength asymmetry.

Microstructure,texture evolution and yield strength symmetry improvement of as-extruded ZK60 Mg alloy via multi-directional impact forging

Multi-direction impact forging(MDIF)was applied to the as-extruded ZK60 Mg alloy,and the microstructure,texture evolution and yield strength symmetry were investigated in the current study.The results showed that the average grain size of forged piece was greatly refined to 5.3μm after 120 forging passes,which was ascribed to the segmenting effect of{10–12}twins and the subsequent multiple rounds of dynamic recrystallization(DRX).A great deal of{10–12}twins were activated at the beginning of MDIF process,which played an important role in grain refinement.With forging proceeding,continuous and discontinuous DRX were successively activated,resulting in the fully DRXed microstructure.Meanwhile,the forged piece exhibited a unique four-peak texture,and the initial<10-10>//ED fiber texture component gradually evolved into multiple texture components composed of<0001>//FFD(first forging direction)and<11–20>//FFD texture.The special strain path was the key to the formation of the unique four-peak texture.The{10–12}twinning and basal slip were two dominant factors to the evolution of texture during MDIF process.Grain strengthening and dislocation strengthening were two main strengthening mechanisms of the forged piece.Besides,the symmetry of yield strength was greatly improved by MDIF process.

Influence of pre- plastic deformation on thermal residual stress and yield strength of SiC_w/Al composites

With a micro mechanical model, the feasibility of modification of thermal residual stress of the composites treated by tensile pre plastic deformation was analyzed. The relationship between pre plastic strain and variation of thermal residual stress was established. By using the method of tensile pre plastic deformation, the thermal residual stress in 20%SiC w/6061Al composites was modified. The results show that, with increasing tensile pre plastic strain, the tensile residual stress in the matrix was decreased to zero gradually, and then it was turned into compressive stress. By comparison, it was found that the changing tendency of the test results is similar to that of theoretical analysis. In addition, due to pre plastic deformation, the dislocation density in the matrix was increased, and the yield strength of the composites was improved. The increasing yield strength is mainly due to the decreasing tensile residual stress and the changing of distribution of dislocation in the matrix.

Effect of Ti content on the yield strength of Nb-Ti microalloyed steels

The hot rolling experiment investigates into the relationship between the microstructures and the mechanical properties of Nb-Ti microalloyed steels with various Ti contents. The results indicate that the effect of the bainite fraction of Nb-Ti microalloyed steels on the yield strength of the steels is not related to Ti content, while the slope of the Hall- Petch relationship decreases with the increase of Ti content. Accordingly, the Misra model for the yield strength of Nb-Ti microalloyed steels is modified, and the factors which cause the change in the slope of Hall-Petch relationship are discussed.

Effects of culm carbohydrate partitioning on basal stem strength in a high-yielding rice population

Rice culm carbohydrate transport can simultaneously affect grain filling and stem lodging resistance by regulating non-structural carbohydrate(NSC) and structural carbohydrate(SC) contents. However, the relationship between carbohydrate transposition and culm strength is not well documented. Accordingly, a high-yielding hybrid rice cultivar(Y Liangyou 2) was tested under different N fertilization regimes at two locations, Taoyuan(a special high-yield eco-site), Yunnan province and Danyang(a representative eco-site of the middle and lower Yangtze), Jiangsu province, China. Significantly higher grain yield and basal stem strength were found at Taoyuan than Danyang under all N rates throughout the two-year experiment. At heading stage, soluble sugars, starch, cellulose and lignin contents of the basal culm at Taoyuan were significantly 132.0%, 73.7%, 1.2%, and 62.7% higher than those at Danyang, respectively. At 20 days after heading, soluble sugars and starch content at Taoyuan decreased significantly compared to Danyang, but lignin content remained higher. Culm carbohydrate transport to kernels at Taoyuan was significantly greater than that at Danyang, and the proportion of soluble sugars and starch was correspondingly 62.9%lower. However, the proportion of lignin and cellulose was 22.7% higher at Taoyuan than that at Danyang. Soluble sugars and starch partitioning were significantly reduced under an increased nitrogen application rate, but SC partitioning was little affected. There were significant positive correlations between basal culm bending stress and dry weight and cellulose and lignin proportions at both locations under all N rates, suggesting that the higher SC proportion at 20 days after heading was primarily responsible for culm strength.These results suggest that high-yielding rice populations with greater culm strength require both moderate NSC transport and greater SC accumulation.

Magnetization-Enhanced Dislocation Motion and Decreased Yield Strength of 60Fe40Ni Alloy

Using a special constant deflection device, the changes in dislocation configuration ahead of a loaded crack tip for 60Fe40Ni alloy. before and after magnetization in a magnetic field, have been studied in TEM. The results showed that the magnetization for 60Fe40Ni alloy could enhance dislocation emission, multiplication and motion. Also, the mechanical properties of 60Fe40Ni alloy, in air and in the magnetic field respectively have been investigated using the slow strain rate tension. And the results indicated that magnetization could make the yield strength corresponding to decrease by 26 percent, but did not influence the ultimate tensile strength and the fracture strain, which showed that magnetization could enhance plastic deformation.

An Application of the Modified Shear Lag Model to Study the Influence of Thermal Residual Stresses on the Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

The modified shear lag model proposed recently was applied to calculate thermal residual stresses and subsequent stress distributions under tensile and compressive loadings. The expressions for the elastic moduli and the yield strengths under tensile and compressive loadings were derived which take account of thermal residual stresses. The asymmetries in the elastic modulus and the yield strength were interpreted using the derived expressions and the obtained results of the stress calculations. The model predictions have exhibited good agreements with the experimental results and also with the other theoretical predictions

Mechanical model for yield strength of nanocrystalline materials under high strain rate loading

To understand the high strain rate deformation mechanism and determine the grain size,strain rate and porosity dependent yield strength of nanocrystalline materials,a new mechanical model based on the deformation mechanism of nanocrystalline materials under high strain rate loading was developed.As a first step of the research,the yield behavior of the nanocrystalline materials under high strain rate loading was mainly concerned in the model and uniform deformation was assumed for simplification.Nanocrystalline materials were treated as composites consisting of grain interior phase and grain boundary phase,and grain interior and grain boundary deformation mechanisms under high strain rate loading were analyzed,then Voigt model was applied to coupling grain boundary constitutive relation with mechanical model for grain interior phase to describe the overall yield mechanical behavior of nanocrystalline materials.The predictions by the developed model on the yield strength of nanocrysatlline materials at high strain rates show good agreements with various experimental data.Further discussion was presented for calculation results and relative experimental observations.

Influence of yield-to-tensile strength ratio(Y/T) on failure assessment of defect-free and corroded X70 steel pipeline

The effect of yield-to-tensile strength ratio(Y/T) on failure pressure of X70 pipeline without and with corrosion defects was investigated.The stress-strain response of materials was characterized by a power-law hardening curve.Two formulas to estimate the strain hardening exponent n for a special Y/T were obtained by least squared regression method and the influence of Y/T on n was analyzed.As an application of n-Y/T expression,the analytical solutions of burst pressure for X70 pipeline without and with corrosion defects were also obtained.The results indicate that the burst pressure of defect-free X70 pipe without corrosion defects is a function of the Y/T,pipe geometry t0/D0 and engineering tensile strength,and increases as Y/T or t0/D0 increases; whilst the burst pressure of corroded X70 pipe decreases with the increase of defect depths,d/t.Comparisons indicate that the present analytical solutions closely match available experimental and numerical data.

CALCULATION OF YIELD STRENGTH IN NICKEL BASE SINGLE CRYSTAL SUPERALLOYS

In this article, a quantitative equation was established to determine the relationship between yield strength and composition in nickel base SC superalloys based on Copley Kear precipitation strengthening model. The yield strength of two well known commercial SC superalloys calculated by this equation was compared with experimental data. It was found that the calculated yield strength of these two alloys was fairly correspondent with experimental results reported in the references. This model accurately described the solution strengthening of alloying elements and precipitation strengthening of γ′ phase. Yield strength of SC superalloys can be successfully predicted by this equation.

Effect of low temperature treatment on tensile yield strength of SiC_w/6061 Al alloy composites

The effect of the low temperature treatment at -78 ℃ and -196 ℃ on the microstructure and properties of 18%SiC w/6061(volume fraction) Al alloy composites of as squeeze casting were studied. The results show that, after the low temperature treatment, the dislocation density in matrix increases, and the residual stress of the matrix decreases, as well as the tensile yield strength of the composites improves. The high residual stress exists in the matrix of the composites of as original squeeze casting. The mismatch degree between the matrix and SiC w phases increases during the low temperature treatment. The matrix undergoes the tensile plastic deformation during the cooling procedure. On the contrary, the matrix encountered an elastic unloading procedure during the heating up process from low temperature to room temperature. The increase of dislocation density and the decrease of residual stress in the matrix are the main reason of the improvement for tensile yield strength of the composites.

SURFACE YIELD STRENGTH AND FATIGUE LIMIT FOR STEELS

The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).

Yield strength of attached copper film

Variation of stress in attached copper film with an applied strain is measured by X-ray diffraction combined with a four-point bending method. A lower slope of the initial elastic segment of the curve of X-ray measured stress versus applied strain results from incomplete elastic strain transferred from the substrate to the film due to insufficiently strong interface cohesion. So the slope of the initial elastic segment of the X-ray stress （or X-ray strain directly） of the film against the substrate applied strain may be used to measure the film-substrate cohesive strength. The yield strength of the attached copper film is much higher than that of the bulk material and varies linearly with the inverse of the film thickness.

Unusual softening behavior of yield strength in niobium at high pressures

In situ synchrotron angle-dispersive x-ray diffraction experiments on niobium powders have been conducted at pressures up to 61 GPa and room temperature using the diamond anvil cell technique. From the full width at half maximum of the measured diffraction lines, the yield strength was derived with the line-width analysis theory. The niobium powder sample was found to be compressed more packed firstly and then yielded at~14 GPa–18 GPa. Following an initial increase in the yield strength with pressure, an obvious decrease was observed occurring at ~42 GPa–47 GPa accompanying with a typical pressure dependence above 47 GPa. The experimentally observed anomalous softening of the yield strength in niobium surprisingly follows the trend of the predicted unusual softening in the shear modulus by the recent theoretical investigations. The possible mechanisms, applicable to interpret the yield strength softening of materials at high pressure,were also discussed in detail.

Study on Anisotropy and Punching Yield Strength of Knitted Fabrics

In terms of the structural characteristics, knitted fabrics are described as plane orthotropic body with two symmetric axes, and the stress in different direction is approximately linear with strain before the yield point.The punching yield strength can be predicted theoretically by developing a mathematical equation from anisotropic effect of knitted fabrics. The experimental results demonstrate the applicability of theoretical formula. Analyses also reveal that the factors influencing three-dimensional deforming performance can be divided into two categories: fiber-yarn-fabric structural features and deforming condition.

FEATURE OF SERRATED YIELDING IN HIGH STRENGTH Al-Zn-Mg-Cu ALLOY

The temperature dependence of critical strain for serrated yielding in high strength A1-Zn-Mg-Cu alloy may be divided into two temperature regions.Their temperature coefficients of critical strain will be negative and positive,respectively.

Growth, yield and fiber quality characteristics of Bt and non-Bt cotton cultivars in response to boron nutrition

Background Boron(B)deficiency is an important factor for poor seed cotton yield and fiber quality.However,it is often missing in the plant nutrition program,particularly in developing countries.The current study investigated B’s effect on growth,yield,and fiber quality of Bt(CIM-663)and non-Bt(Cyto-124)cotton cultivars.The experimental plan consisted of twelve treatments:Control(CK);B at 1 mg·kg^(−1) soil application(SB1);2 mg·kg^(−1) B(SB2);3 mg·kg^(−1) B(SB3);0.2%B foliar spray(FB1);0.4%B foliar spray(FB2);1 mg·kg^(−1) B+0.2%B foliar spray(SB1+FB1);1 mg·kg^(−1) B+0.4%B foliar spray(SB1+FB2);2 mg·kg^(−1) B+0.2%B foliar spray(SB2+FB1);2 mg·kg^(−1) B+0.4%B foliar spray(SB2+FB2);3 mg·kg^(−1) B+0.2%B foliar spray(SB3+FB1);3 mg·kg^(−1) B+0.4%B foliar spray(SB3+FB2).Each treat-ment has three replications,one pot having two plants per replication.Results B nutrition at all levels and methods of application significantly(P≤0.05)affected the growth,physiological,yield,and fiber quality characteristics of both cotton cultivars.However,SB2 either alone or in combination with foliar spray showed superiority over others,particularly in the non-Bt cultivar which responded better to B nutrition.Maxi-mum improvement in monopodial branches(345%),sympodial branches(143%),chlorophyll-a(177%),chlorophyll-b(194%),photosynthesis(169%),and ginning out turn(579%)in the non-Bt cultivar was found with SB2 compared with CK.In Bt cultivar,although no consistent trend was found but integrated use of SB3 with foliar spray performed relatively better for improving cotton growth compared with other treatments.Fiber quality characteristics in both cultivars were improved markedly but variably with different B treatments.Conclusion B nutrition with SB2 either alone or in combination with foliar spray was found optimum for improving cotton’s growth and yield characteristics.

Yield Loci of TRIP590 Advanced High Strength Steel Based on Biaxial Loading Test

The main purpose of the paper is to obtain the experimental yield loci of TRIP590 advanced high strength steel,and to compare it with the theoretical loci in order to obtain the best yield criterion for this material.First,the biaxial loading tests under different loading paths in the method of load control are carried out.Then,the experimental yield loci of different deformation stages are obtained.Finally,the experimental yield loci are compared with the theoretical loci of Mises criterion and Hill48 criterion,the parameters of which are calculated based on the r?value and the yield stress method,respectively.The results show that the accuracy of the theoretical yield loci of Hill48 based on the yield stress is higher than that of Mises criterion and Hill 48 criterion based on r?value method.

Machine Learning Design of Aluminum-Lithium Alloys with High Strength

Due to the large unexplored compositional space,long development cycle,and high cost of traditional trial-anderror experiments,designing high strength aluminum-lithium alloys is a great challenge.This work establishes a performance-oriented machine learning design strategy for aluminum-lithium alloys to simplify and shorten the development cycle.The calculation results indicate that radial basis function(RBF)neural networks exhibit better predictive ability than back propagation(BP)neural networks.The RBF neural network predicted tensile and yield strengths with determination coefficients of 0.90 and 0.96,root mean square errors of 30.68 and 25.30,and mean absolute errors of 28.15 and 19.08,respectively.In the validation experiment,the comparison between experimental data and predicted data demonstrated the robustness of the two neural network models.The tensile and yield strengths of Al-2Li-1Cu-3Mg-0.2Zr(wt.%)alloy are 17.8 and 3.5 MPa higher than those of the Al-1Li4.5Cu-0.2Zr(wt.%)alloy,which has the best overall performance,respectively.It demonstrates the reliability of the neural network model in designing high strength aluminum-lithium alloys,which provides a way to improve research and development efficiency.