This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by...This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.展开更多
A kind of ceramic slurry was prepared and sprayed onto the surface of 9Ni steel at room temperature. The coating layer will not only reduce the depth of the formed Ni-enriched entanglement at high temperature but also...A kind of ceramic slurry was prepared and sprayed onto the surface of 9Ni steel at room temperature. The coating layer will not only reduce the depth of the formed Ni-enriched entanglement at high temperature but also have an excellent ability to resist oxidation of the 9Ni steel. Compared to bare specimen, the depths of the entanglement of the coated 9Ni specimen could be successfully reduced by 74.1% and the oxidation loss be decreased by 62.3% by heating at 1 250 ℃ for 60 min. In addition, the coated specimen indicates no trace of oxide pegs. It proves that the coating has outstanding improvement to internal oxidation resistance. Some characterization methods such as metalloscopy, XRD, XPS, SEM and EDX have been used to reveal a possible protective mechanism. The result shows that the coating layer reacts with the iron oxide to form Mg Fe2O4 on the surface of the coated specimen, which could provide a smaller diffusion coefficient rate of Fe ion. The coating with a low cost and easy implementation is promisingly applicable in the slab-reheating process of the 9Ni steel.展开更多
An experiment model, scaled 1: 1, designed for studying a blasting method to clear away soot in a soot-delivery pipe in coal-burning power plant is described. By mixing RDX and Nitramon on a particular scale and stick...An experiment model, scaled 1: 1, designed for studying a blasting method to clear away soot in a soot-delivery pipe in coal-burning power plant is described. By mixing RDX and Nitramon on a particular scale and sticking the explosive cartridge on the outwall surface of the pipe, the experimental result makes clear that the controlled blasting method can get rid of the soot effectively. Under the action of the blasting compression wave and reflectance tension wave,the soot is destroyed effectively in the region of - 60° ~60° around the bIasting site, that creates a condition for the second blasting in the surplus soot.展开更多
The suitability of high pressure nozzles in terms of impact upon targeted surfaces has indicated its effectiveness for the cleaning of oil production tubing scale, which has recently attracted wider industrial applica...The suitability of high pressure nozzles in terms of impact upon targeted surfaces has indicated its effectiveness for the cleaning of oil production tubing scale, which has recently attracted wider industrial applications considering its efficiency, ease of operation and cost benefit. In the oil and gas production, these nozzles are now used for cleaning the scale deposits along the production tubing resulted mainly from salt crystallization due to pressure and temperature drop. Detailed characterizations of flat-fan nozzle in terms of droplet sizes and mean velocities will benefit momentum computations for the axial and radial distribution along the spray width, with the view of finding the best stand-off distance between the target scale and the spray nozzle. While the droplet sizes and the velocities determine the momentum at impact, measuring droplet sizes has been known to be difficult especially in the high density spray region, still laboratory characterization of nozzles provides a reliable data especially avoiding uncontrollable parameters. While several researches consider break up insensitive to the cleaning performance, this research investigates the experimental data obtained using PDA （phase doppler anemometry） which led to established variation in momentum across the spray width thus, non-uniformity of impact distribution. Comparative model was then developed using Ansys Fluent code, which verifies the eroded surfaces of material using the flat-fan atomizer to have shown variability in the extent of impact actions due to kinetic energy difference between the center and edge droplets. The study＇s findings could be useful in establishing the effect of droplet kinetic energies based on the spray penetration, and will also add significant understanding to the effect of the ligaments and droplets, along the spray penetration in order to ascertain their momentum impact distribution along the targeted surface.展开更多
基金The research was funded by Science and Technology Project of Hebei Education Department(Project Number:QN2022198).Y.C.received the grant.
文摘This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.
基金Funded by the Key Projects in the National Science &Technology Pillar Program in the Twelfth Five-year Plan Period(No.2012BAB08B04)the National Natural Science Foundation of China(No.51202249)
文摘A kind of ceramic slurry was prepared and sprayed onto the surface of 9Ni steel at room temperature. The coating layer will not only reduce the depth of the formed Ni-enriched entanglement at high temperature but also have an excellent ability to resist oxidation of the 9Ni steel. Compared to bare specimen, the depths of the entanglement of the coated 9Ni specimen could be successfully reduced by 74.1% and the oxidation loss be decreased by 62.3% by heating at 1 250 ℃ for 60 min. In addition, the coated specimen indicates no trace of oxide pegs. It proves that the coating has outstanding improvement to internal oxidation resistance. Some characterization methods such as metalloscopy, XRD, XPS, SEM and EDX have been used to reveal a possible protective mechanism. The result shows that the coating layer reacts with the iron oxide to form Mg Fe2O4 on the surface of the coated specimen, which could provide a smaller diffusion coefficient rate of Fe ion. The coating with a low cost and easy implementation is promisingly applicable in the slab-reheating process of the 9Ni steel.
文摘An experiment model, scaled 1: 1, designed for studying a blasting method to clear away soot in a soot-delivery pipe in coal-burning power plant is described. By mixing RDX and Nitramon on a particular scale and sticking the explosive cartridge on the outwall surface of the pipe, the experimental result makes clear that the controlled blasting method can get rid of the soot effectively. Under the action of the blasting compression wave and reflectance tension wave,the soot is destroyed effectively in the region of - 60° ~60° around the bIasting site, that creates a condition for the second blasting in the surplus soot.
文摘The suitability of high pressure nozzles in terms of impact upon targeted surfaces has indicated its effectiveness for the cleaning of oil production tubing scale, which has recently attracted wider industrial applications considering its efficiency, ease of operation and cost benefit. In the oil and gas production, these nozzles are now used for cleaning the scale deposits along the production tubing resulted mainly from salt crystallization due to pressure and temperature drop. Detailed characterizations of flat-fan nozzle in terms of droplet sizes and mean velocities will benefit momentum computations for the axial and radial distribution along the spray width, with the view of finding the best stand-off distance between the target scale and the spray nozzle. While the droplet sizes and the velocities determine the momentum at impact, measuring droplet sizes has been known to be difficult especially in the high density spray region, still laboratory characterization of nozzles provides a reliable data especially avoiding uncontrollable parameters. While several researches consider break up insensitive to the cleaning performance, this research investigates the experimental data obtained using PDA （phase doppler anemometry） which led to established variation in momentum across the spray width thus, non-uniformity of impact distribution. Comparative model was then developed using Ansys Fluent code, which verifies the eroded surfaces of material using the flat-fan atomizer to have shown variability in the extent of impact actions due to kinetic energy difference between the center and edge droplets. The study＇s findings could be useful in establishing the effect of droplet kinetic energies based on the spray penetration, and will also add significant understanding to the effect of the ligaments and droplets, along the spray penetration in order to ascertain their momentum impact distribution along the targeted surface.
