The automobile industry has been searching for vehicles that use less energy and emit fewer pollutants, which has resulted in a high demand for fuel-efficient vehicles. Because of their higher strength-to-weight ratio...The automobile industry has been searching for vehicles that use less energy and emit fewer pollutants, which has resulted in a high demand for fuel-efficient vehicles. Because of their higher strength-to-weight ratio compared to traditional steel, using fiber-reinforcement composite materials in automobile bodies has emerged as the most effective strategy for improving fuel efficiency while maintaining safety standards. This research paper examined the utilization of fiber-reinforced composite materials in car bodies to meet the increasing consumer demand for fuel-efficient and eco-friendly vehicles. It particularly focused on a carbon-aramid fiber-reinforced composite impact beam for passenger car side door impact protection. Despite the encouraging prospects of the carbon-aramid fiber-reinforced beam, the research uncovered substantial defects in the fabrication process, resulting in diminished load-bearing capacity and energy absorption. As a result, the beam was un-successful in three-point bending tests. This was accomplished by using an I cross-section design with varying thickness because of the higher area moment of inertia. Vacuum-assisted resin transfer molding (VARTM) manufacturing process was used and the finished beam underwent to three-point bending tests.展开更多
Uganda has jurisdiction to try war criminals if the cases are referred to Kampala THE pending global arrest warrants issued against Sudan’s President Omar al Bashir and Libya’s President Muammar Gaddafi are some of ...Uganda has jurisdiction to try war criminals if the cases are referred to Kampala THE pending global arrest warrants issued against Sudan’s President Omar al Bashir and Libya’s President Muammar Gaddafi are some of the high-profile cases that Uganda is banking on to successfully prosecute,as it seeks to become a beacon of justice in East Africa. Speaking to ChinAfrica from Kampala,capital of Uganda,the spokesperson of the Uganda Judi-展开更多
In order to study the dynamic response of the unmanned aerial vehicle cabin door opening and closing system under impact load conditions, considering the flexible treatment of mechanical components, and the system’s ...In order to study the dynamic response of the unmanned aerial vehicle cabin door opening and closing system under impact load conditions, considering the flexible treatment of mechanical components, and the system’s motion with different stiffness of energy-absorbing components, a rigid-flexible coupling model of the cabin door actuation system was established in LMS. Virtual. Motion. In Amesim, a control model of the motor was created. Through the Motion-Amesim co-simulation module, the dynamic module of the system was combined with the motor control module to complete the electromechanical coupling simulation and analyze the results. .展开更多
文摘The automobile industry has been searching for vehicles that use less energy and emit fewer pollutants, which has resulted in a high demand for fuel-efficient vehicles. Because of their higher strength-to-weight ratio compared to traditional steel, using fiber-reinforcement composite materials in automobile bodies has emerged as the most effective strategy for improving fuel efficiency while maintaining safety standards. This research paper examined the utilization of fiber-reinforced composite materials in car bodies to meet the increasing consumer demand for fuel-efficient and eco-friendly vehicles. It particularly focused on a carbon-aramid fiber-reinforced composite impact beam for passenger car side door impact protection. Despite the encouraging prospects of the carbon-aramid fiber-reinforced beam, the research uncovered substantial defects in the fabrication process, resulting in diminished load-bearing capacity and energy absorption. As a result, the beam was un-successful in three-point bending tests. This was accomplished by using an I cross-section design with varying thickness because of the higher area moment of inertia. Vacuum-assisted resin transfer molding (VARTM) manufacturing process was used and the finished beam underwent to three-point bending tests.
文摘Uganda has jurisdiction to try war criminals if the cases are referred to Kampala THE pending global arrest warrants issued against Sudan’s President Omar al Bashir and Libya’s President Muammar Gaddafi are some of the high-profile cases that Uganda is banking on to successfully prosecute,as it seeks to become a beacon of justice in East Africa. Speaking to ChinAfrica from Kampala,capital of Uganda,the spokesperson of the Uganda Judi-
文摘In order to study the dynamic response of the unmanned aerial vehicle cabin door opening and closing system under impact load conditions, considering the flexible treatment of mechanical components, and the system’s motion with different stiffness of energy-absorbing components, a rigid-flexible coupling model of the cabin door actuation system was established in LMS. Virtual. Motion. In Amesim, a control model of the motor was created. Through the Motion-Amesim co-simulation module, the dynamic module of the system was combined with the motor control module to complete the electromechanical coupling simulation and analyze the results. .
