The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to...The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to 10 s-1. From the true stress-true strain curve, the flow stress increases with the increasing of strain and tends to be constant after a peak value, showing dynamic recover, and the peak value of flow stress increases with the decreasing of deformation temperature and the increasing of strain rate.When the strain rate is 10 s-1 and the deformation temperature is higher than 400 °C, the flow stress shows dynamic recrystallization characteristic. TEM micrographs were used to reveal the evolution of microstructures. According to the processing map at true strain of 0.7, the feasible deformation conditions are high strain rate(>0.5 s-1) or 440-500 °C and 0.01-0.02 s-1.展开更多
Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, w...Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, were conducted and described in this study. The dynamic compression, tensile and shear properties of high nitrogen steel had been tested, and the stress-strain curves under high strain rates were obtained. The results have been showed as follows: High nitrogen steel has a remarkable strain rate strengthening effect. Compared to the static curves, the constitutive curves of dynamic tension and compression move upper. The dynamic compressive yield strength of high nitrogen steel increases first and then decreases with the increase of strain rate, and the yield strength varies in the range of 1465-1549 MPa within the range of 1147-2042 s^(-1) strain rate; The tensile strength of high nitrogen steel increases with the increase of strain rate. When the strain rate is greater than 1341 s^(-1), the tensile strength will not increase and the curve tends to be gentle. The pure shear yield strength of the high nitrogen steel is above 800 MPa.展开更多
为解决在选择性催化还原技术(selective catalytic reduction,SCR)的控制策略开发中局部线性模型树(local linear model tree,LOLIMOT)排放模型预测精度不足的问题,提出一种通过优化空间边界,将原模型的超矩形输入空间约束在物理意义范...为解决在选择性催化还原技术(selective catalytic reduction,SCR)的控制策略开发中局部线性模型树(local linear model tree,LOLIMOT)排放模型预测精度不足的问题,提出一种通过优化空间边界,将原模型的超矩形输入空间约束在物理意义范围内的改进LOLIMOT模型。通过某天然气发动机的辨识试验,从分布特征和计算原理角度,分析了该方法对预测结果的影响。结果表明:与原算法相比,改进算法的线性相关度R2提升了1.9%,验证了改进策略的有效性。改进LOLIMOT算法具备较高的收敛速度和稳定性,在排放模型领域具备一定的应用优势。展开更多
基金Project(51301209) supported by the National Natural Science Foundation of ChinaProject(201191107) supported by Science and Technology Plan of Xinjiang Province,China
文摘The flow stress behavior of high-purity Al-Cu-Mg alloy under hot deformation conditions was studied by Gleeble-1500,with the deformation temperature range from 300 to 500 °C and the strain rate range from 0.01 to 10 s-1. From the true stress-true strain curve, the flow stress increases with the increasing of strain and tends to be constant after a peak value, showing dynamic recover, and the peak value of flow stress increases with the decreasing of deformation temperature and the increasing of strain rate.When the strain rate is 10 s-1 and the deformation temperature is higher than 400 °C, the flow stress shows dynamic recrystallization characteristic. TEM micrographs were used to reveal the evolution of microstructures. According to the processing map at true strain of 0.7, the feasible deformation conditions are high strain rate(>0.5 s-1) or 440-500 °C and 0.01-0.02 s-1.
文摘Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, were conducted and described in this study. The dynamic compression, tensile and shear properties of high nitrogen steel had been tested, and the stress-strain curves under high strain rates were obtained. The results have been showed as follows: High nitrogen steel has a remarkable strain rate strengthening effect. Compared to the static curves, the constitutive curves of dynamic tension and compression move upper. The dynamic compressive yield strength of high nitrogen steel increases first and then decreases with the increase of strain rate, and the yield strength varies in the range of 1465-1549 MPa within the range of 1147-2042 s^(-1) strain rate; The tensile strength of high nitrogen steel increases with the increase of strain rate. When the strain rate is greater than 1341 s^(-1), the tensile strength will not increase and the curve tends to be gentle. The pure shear yield strength of the high nitrogen steel is above 800 MPa.
文摘为解决在选择性催化还原技术(selective catalytic reduction,SCR)的控制策略开发中局部线性模型树(local linear model tree,LOLIMOT)排放模型预测精度不足的问题,提出一种通过优化空间边界,将原模型的超矩形输入空间约束在物理意义范围内的改进LOLIMOT模型。通过某天然气发动机的辨识试验,从分布特征和计算原理角度,分析了该方法对预测结果的影响。结果表明:与原算法相比,改进算法的线性相关度R2提升了1.9%,验证了改进策略的有效性。改进LOLIMOT算法具备较高的收敛速度和稳定性,在排放模型领域具备一定的应用优势。
