Iron-rich electrolytic manganese residue(IREMR)is an industrial waste produced during the processing of electrolytic metal manganese,and it contains certain amounts of Fe and Mn resources and other heavy metals.In thi...Iron-rich electrolytic manganese residue(IREMR)is an industrial waste produced during the processing of electrolytic metal manganese,and it contains certain amounts of Fe and Mn resources and other heavy metals.In this study,the slurry electrolysis technique was used to recover high-purity Fe powder from IREMR.The effects of IREMR and H2SO4 mass ratio,current density,reaction temper-ature,and electrolytic time on the leaching and current efficiencies of Fe were studied.According to the results,high-purity Fe powder can be recovered from the cathode plate,and the slurry electrolyte can be recycled.The leaching efficiency,current efficiency,and purity of Fe reached 92.58%,80.65%,and 98.72wt%,respectively,at a 1:2.5 mass ratio of H2SO4 and IREMR,reaction temperature of 60℃,electric current density of 30 mA/cm^(2),and reaction time of 8 h.In addition,vibrating sample magnetometer(VSM)analysis showed that the coercivity of electrolytic iron powder was 54.5 A/m,which reached the advanced magnetic grade of electrical pure-iron powder(DT4A coercivity standard).The slurry electrolytic method provides fundamental support for the industrial application of Fe resource recovery in IRMER.展开更多
Experimental results on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature are reported....Experimental results on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature are reported. Optical microscopy and scanning electron microscopy were used to examine the microstructures of starting tungsten powder, carburized powder, and deposit. X-ray diffraction analysis, thermal gravimetric analysis and microhardness measurement were used to characterize the structures and properties of the powder and the deposit. It is found that the primary carburization reaction in the induction plasma starts from the surface of tungsten particles when the particles are melted. Tungsten particles are partially carburized inside the reactive plasma. Complete carburization is achieved through the secondary carburization reaction of the deposit on substrate at high temperature.展开更多
Scandia and rhenium doped tungsten powders were prepared by solid-liquid doping combined with two-step reduction method. The particle size of doped tungsten and distribution of scandia and rhenium were studied by SEM,...Scandia and rhenium doped tungsten powders were prepared by solid-liquid doping combined with two-step reduction method. The particle size of doped tungsten and distribution of scandia and rhenium were studied by SEM, EDS, XRD and granularity analysis. Experimental results showed that scandia distributed evenly on the surface of tungsten particles. Addition of scandia and rhenium decreased the particle size of doped tungsten, and the more the content of scandia and rhenium, the smaller the doped tungsten particles. Tungsten powders doped with 3 % Sc2O3 and 3 % Re （mass fraction） had an average size of about 80 nm in diameter. The mechanism of the decrease in the tungsten particle size was discussed.展开更多
Sol-gel method was employed for the preparation of nanoscale tungsten powder. The effects of different preparation conditions on particle size were discussed and the optimum preparation condition was found. The produc...Sol-gel method was employed for the preparation of nanoscale tungsten powder. The effects of different preparation conditions on particle size were discussed and the optimum preparation condition was found. The products were characterized by X-ray diffraction, scan electron microscopy and so on. The results show that the intermediate is monoclinic WO3, its particle shape is approximately spherical, and the particle size distribution is narrow. The average particle size is about 60 nm. After deoxidization, WO3 turns into cubic tungsten powder with small particle size （average particle size about 120 nm） and narrow size distribution.展开更多
Tungsten powder was fabricated from the system CaWO4-Mg by self-propagating high-temperature synthesis (SHS) with a magnesium thermit stage. The physic-chemical change during heating and the effects of pressure of sam...Tungsten powder was fabricated from the system CaWO4-Mg by self-propagating high-temperature synthesis (SHS) with a magnesium thermit stage. The physic-chemical change during heating and the effects of pressure of sample and diluents (W powder) on product have been studied. The experimental results show that the porosity of combustion product and the particle size of final tungsten powder decrease with increasing pressure of sample. Addition of diluents could increase the particle size of final tungsten powder. The purity of tungsten is improved by leaching in NaOH solution. The results of spectral analysis and particle size distribution of final tungsten powder show that the final Tungsten powder has a median diameter of 0.87μm,specific surface area of 1.09m2/g and purity of above 99.0%.展开更多
Nanosized tungsten powder was synthesized by means of different methods and under different conditions with nanosized WO3 powder. The powder and the intermediate products were characterized using XRD, SEM, TEM, BET （...Nanosized tungsten powder was synthesized by means of different methods and under different conditions with nanosized WO3 powder. The powder and the intermediate products were characterized using XRD, SEM, TEM, BET （Brunauer Emmett Teller Procedure） and SAXS （X-ray diffracto-spectrometer/Kratky small angle scattering goniometer）. The results show that nanosized WO3 can be completely reduced to WO2 at 600℃ after 40 min, and WO2 can be reduced to W at 700℃ after 90 min, moreover, the mean size of W particles is less than 40 nm. Furthermore, the process of WO3→WO2→W excelled that of WO3→W in getting stable nanosized tungsten powder with less grain size.展开更多
An improved wax based multi component binder and a new debinding method termed high pressure condensed solvent extraction were developed for powder injection molding of tungsten cemented carbide. The results indicate ...An improved wax based multi component binder and a new debinding method termed high pressure condensed solvent extraction were developed for powder injection molding of tungsten cemented carbide. The results indicate that a critical powder loading of 65% (volume fraction) and an ideal rheological properties were obtained by the feedstock based on the binder. High debinding rate and specimens with high strength were obtained by the debinding method. Moreover, by making high temperature holding time adjustable, it makes the subsequent thermal degradation process more flexible to debinding atmosphere and carbon content of the as debinded specimens controllable. The transverse rupture strength, hardness and density of the as sintered specimens made by an optimized PIM process are 2.48 GPa, HRA90 and 14.72 g/cm 3, respectively. Good shape retention and about 0.02% dimension deviation were achieved.展开更多
The influence of phase components of tungsten oxide on homogeneity of ultrafine tungsten powder by conventional hydrogen reduction techniques was studied. Results show that phase components of tungsten oxide play a cr...The influence of phase components of tungsten oxide on homogeneity of ultrafine tungsten powder by conventional hydrogen reduction techniques was studied. Results show that phase components of tungsten oxide play a crucial role on homogeneity of metal tungsten powder; ultrafine and homogeneous tungsten powder can be produced from oxides which consist of only one phase. Due to the different reduction rates (or different reduction paths) of oxide which comprises different phases, the multi phase components tungsten oxide leads to a fine but in homogeneous metal tungsten powder.展开更多
The preparation of nanostructured tungsten powders has been studied by using the characteristics of high-er temperature, higher chemical reactivity and quenching technology of hydrogen plasma,in which WO3 solid partic...The preparation of nanostructured tungsten powders has been studied by using the characteristics of high-er temperature, higher chemical reactivity and quenching technology of hydrogen plasma,in which WO3 solid particles served as raw materials. The reduction mechanism of WO3 at high temperature has been also discussed. The composition . particle size distribution and morphology of nanostructured tungsten powders have been measured by X?ray diffraction small angle X-ray scatter and TEM. Tungsten powders of mean particle size of 40 nanometer,and specific surface area of 3 X10m2/kg have been prepared. The shape of nanostruc-tutted tungsten powders is sphere.展开更多
Tungsten alloys were prepared with mechanically activated powder added microelement cobalt in order to improve the process and properties of alloys. Properties of alloys such as density, hardness and bending strength ...Tungsten alloys were prepared with mechanically activated powder added microelement cobalt in order to improve the process and properties of alloys. Properties of alloys such as density, hardness and bending strength were measured. The results show that through mechanical activation, cobalt can accelerate the sintering process of these alloys By the combination of mechanical activation and adding microelement cobalt, tungsten alloys with higher density and better properties can be obtained.展开更多
Three types of tungsten powders were prepared by hydrogen reduction of three precursor powders at low temperature, which were used as samples, and were then characterized by Brunauer-Emmer-Teller （BET） method, scann...Three types of tungsten powders were prepared by hydrogen reduction of three precursor powders at low temperature, which were used as samples, and were then characterized by Brunauer-Emmer-Teller （BET） method, scanning electron microscopy （SEM）, transmission electronic microscopy （TEM）, small angle X-ray scattering （SAXS）, and field-emission scanning election microscopy （FESEM） respectively. The results showed that although BET and SEM could not characterize the particle size of nanometer powders, they were important means of assistance to exclude non-nanometer powders. TEM and FESEM could directly measure the particle size of nanometer powders, but this needs a lot of time, to count the average particle size and particle size distribution. SAXS could not describe the state of agglomeration. By the combination of FESEM and SAXS, the particle size, particle size distribution, and particle shape of nanometer powders could be precisely characterized.展开更多
The microstructure and properties of liquid-phase sintered 93W-4.9Ni-2.1Fe tungsten heavy alloys using ultra-fine tungsten powders (medium particle size of 700 nm) and original tungsten powders (medium particle size o...The microstructure and properties of liquid-phase sintered 93W-4.9Ni-2.1Fe tungsten heavy alloys using ultra-fine tungsten powders (medium particle size of 700 nm) and original tungsten powders (medium particle size of 3 μm) were investigated respectively. Commercial tungsten powders (original tungsten powders) were mechanically milled in a high-energy attritor mill for 35 h. Ultra-fine tungsten powders and commercial Ni, Fe powders were consolidated into green compacts by using CIP method and liquid-phase sintering at 1 465 ℃ for 30 min in the dissociated ammonia atmosphere. Liquid-phase sintered tungsten heavy alloys using ultra-fine tungsten powders exhibit full densification (above 99% in relative density) and higher strength and elongation compared with conventional liquid-phase sintered alloys using original tungsten powders due to lower sintering temperature at 1 465 ℃ and short sintering time. The mechanical properties of sintered tungsten heavy alloy are found to be mainly dependent on the particles size of raw tungsten powders and liquid-phase sintering temperature.展开更多
The flow behavior of feedstock for the tungsten alloy powder in the mold cavity was approximately described using Hele-Shaw flow model. The math model consisting of momentum equation, consecutive equation and thermo-c...The flow behavior of feedstock for the tungsten alloy powder in the mold cavity was approximately described using Hele-Shaw flow model. The math model consisting of momentum equation, consecutive equation and thermo-conduction equation for describing the injection process was established. The equations are solved by the finite element/finite difference hybrid method that means dispersing the feedstock model with finite element method, resolving the model along the depth with finite difference method, and tracking the movable boundary with control volume method, then the pressure equation and energy equation can be resolved in turn. The numerical simulation of the injection process and the identification of the process parameters were realized by the Moldflow software. The results indicate that there is low temperature gradient in the cavity while the pressure and shear rate gradient are high at high flow rate. The selection of the flow rate is affected by the structure of the gate. The shear rate and the pressure near the gate can be decreased by properly widening the dimension of the gate. There is a good agreement between the process parameters obtained by the numerical simulation and the actual ones.展开更多
基金supported by the Key Research and Development Program of Guangxi Province,China (No.AB23075174)the National Natural Science Foundation of China (No.52174386)the Science and Technology Plan Project of Sichuan Province,China (No.2022YFS0459).
文摘Iron-rich electrolytic manganese residue(IREMR)is an industrial waste produced during the processing of electrolytic metal manganese,and it contains certain amounts of Fe and Mn resources and other heavy metals.In this study,the slurry electrolysis technique was used to recover high-purity Fe powder from IREMR.The effects of IREMR and H2SO4 mass ratio,current density,reaction temper-ature,and electrolytic time on the leaching and current efficiencies of Fe were studied.According to the results,high-purity Fe powder can be recovered from the cathode plate,and the slurry electrolyte can be recycled.The leaching efficiency,current efficiency,and purity of Fe reached 92.58%,80.65%,and 98.72wt%,respectively,at a 1:2.5 mass ratio of H2SO4 and IREMR,reaction temperature of 60℃,electric current density of 30 mA/cm^(2),and reaction time of 8 h.In addition,vibrating sample magnetometer(VSM)analysis showed that the coercivity of electrolytic iron powder was 54.5 A/m,which reached the advanced magnetic grade of electrical pure-iron powder(DT4A coercivity standard).The slurry electrolytic method provides fundamental support for the industrial application of Fe resource recovery in IRMER.
文摘Experimental results on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature are reported. Optical microscopy and scanning electron microscopy were used to examine the microstructures of starting tungsten powder, carburized powder, and deposit. X-ray diffraction analysis, thermal gravimetric analysis and microhardness measurement were used to characterize the structures and properties of the powder and the deposit. It is found that the primary carburization reaction in the induction plasma starts from the surface of tungsten particles when the particles are melted. Tungsten particles are partially carburized inside the reactive plasma. Complete carburization is achieved through the secondary carburization reaction of the deposit on substrate at high temperature.
基金Project supported by the National Natural Science Foundation of China (50571001)the National "863"Project(2006AA03Z524)
文摘Scandia and rhenium doped tungsten powders were prepared by solid-liquid doping combined with two-step reduction method. The particle size of doped tungsten and distribution of scandia and rhenium were studied by SEM, EDS, XRD and granularity analysis. Experimental results showed that scandia distributed evenly on the surface of tungsten particles. Addition of scandia and rhenium decreased the particle size of doped tungsten, and the more the content of scandia and rhenium, the smaller the doped tungsten particles. Tungsten powders doped with 3 % Sc2O3 and 3 % Re （mass fraction） had an average size of about 80 nm in diameter. The mechanism of the decrease in the tungsten particle size was discussed.
文摘Sol-gel method was employed for the preparation of nanoscale tungsten powder. The effects of different preparation conditions on particle size were discussed and the optimum preparation condition was found. The products were characterized by X-ray diffraction, scan electron microscopy and so on. The results show that the intermediate is monoclinic WO3, its particle shape is approximately spherical, and the particle size distribution is narrow. The average particle size is about 60 nm. After deoxidization, WO3 turns into cubic tungsten powder with small particle size （average particle size about 120 nm） and narrow size distribution.
文摘Tungsten powder was fabricated from the system CaWO4-Mg by self-propagating high-temperature synthesis (SHS) with a magnesium thermit stage. The physic-chemical change during heating and the effects of pressure of sample and diluents (W powder) on product have been studied. The experimental results show that the porosity of combustion product and the particle size of final tungsten powder decrease with increasing pressure of sample. Addition of diluents could increase the particle size of final tungsten powder. The purity of tungsten is improved by leaching in NaOH solution. The results of spectral analysis and particle size distribution of final tungsten powder show that the final Tungsten powder has a median diameter of 0.87μm,specific surface area of 1.09m2/g and purity of above 99.0%.
基金This work was financially supported by the National Science Funds of Beijing (No.2052015).
文摘Nanosized tungsten powder was synthesized by means of different methods and under different conditions with nanosized WO3 powder. The powder and the intermediate products were characterized using XRD, SEM, TEM, BET （Brunauer Emmett Teller Procedure） and SAXS （X-ray diffracto-spectrometer/Kratky small angle scattering goniometer）. The results show that nanosized WO3 can be completely reduced to WO2 at 600℃ after 40 min, and WO2 can be reduced to W at 700℃ after 90 min, moreover, the mean size of W particles is less than 40 nm. Furthermore, the process of WO3→WO2→W excelled that of WO3→W in getting stable nanosized tungsten powder with less grain size.
文摘An improved wax based multi component binder and a new debinding method termed high pressure condensed solvent extraction were developed for powder injection molding of tungsten cemented carbide. The results indicate that a critical powder loading of 65% (volume fraction) and an ideal rheological properties were obtained by the feedstock based on the binder. High debinding rate and specimens with high strength were obtained by the debinding method. Moreover, by making high temperature holding time adjustable, it makes the subsequent thermal degradation process more flexible to debinding atmosphere and carbon content of the as debinded specimens controllable. The transverse rupture strength, hardness and density of the as sintered specimens made by an optimized PIM process are 2.48 GPa, HRA90 and 14.72 g/cm 3, respectively. Good shape retention and about 0.02% dimension deviation were achieved.
文摘The influence of phase components of tungsten oxide on homogeneity of ultrafine tungsten powder by conventional hydrogen reduction techniques was studied. Results show that phase components of tungsten oxide play a crucial role on homogeneity of metal tungsten powder; ultrafine and homogeneous tungsten powder can be produced from oxides which consist of only one phase. Due to the different reduction rates (or different reduction paths) of oxide which comprises different phases, the multi phase components tungsten oxide leads to a fine but in homogeneous metal tungsten powder.
文摘The preparation of nanostructured tungsten powders has been studied by using the characteristics of high-er temperature, higher chemical reactivity and quenching technology of hydrogen plasma,in which WO3 solid particles served as raw materials. The reduction mechanism of WO3 at high temperature has been also discussed. The composition . particle size distribution and morphology of nanostructured tungsten powders have been measured by X?ray diffraction small angle X-ray scatter and TEM. Tungsten powders of mean particle size of 40 nanometer,and specific surface area of 3 X10m2/kg have been prepared. The shape of nanostruc-tutted tungsten powders is sphere.
文摘Tungsten alloys were prepared with mechanically activated powder added microelement cobalt in order to improve the process and properties of alloys. Properties of alloys such as density, hardness and bending strength were measured. The results show that through mechanical activation, cobalt can accelerate the sintering process of these alloys By the combination of mechanical activation and adding microelement cobalt, tungsten alloys with higher density and better properties can be obtained.
文摘Three types of tungsten powders were prepared by hydrogen reduction of three precursor powders at low temperature, which were used as samples, and were then characterized by Brunauer-Emmer-Teller （BET） method, scanning electron microscopy （SEM）, transmission electronic microscopy （TEM）, small angle X-ray scattering （SAXS）, and field-emission scanning election microscopy （FESEM） respectively. The results showed that although BET and SEM could not characterize the particle size of nanometer powders, they were important means of assistance to exclude non-nanometer powders. TEM and FESEM could directly measure the particle size of nanometer powders, but this needs a lot of time, to count the average particle size and particle size distribution. SAXS could not describe the state of agglomeration. By the combination of FESEM and SAXS, the particle size, particle size distribution, and particle shape of nanometer powders could be precisely characterized.
文摘The microstructure and properties of liquid-phase sintered 93W-4.9Ni-2.1Fe tungsten heavy alloys using ultra-fine tungsten powders (medium particle size of 700 nm) and original tungsten powders (medium particle size of 3 μm) were investigated respectively. Commercial tungsten powders (original tungsten powders) were mechanically milled in a high-energy attritor mill for 35 h. Ultra-fine tungsten powders and commercial Ni, Fe powders were consolidated into green compacts by using CIP method and liquid-phase sintering at 1 465 ℃ for 30 min in the dissociated ammonia atmosphere. Liquid-phase sintered tungsten heavy alloys using ultra-fine tungsten powders exhibit full densification (above 99% in relative density) and higher strength and elongation compared with conventional liquid-phase sintered alloys using original tungsten powders due to lower sintering temperature at 1 465 ℃ and short sintering time. The mechanical properties of sintered tungsten heavy alloy are found to be mainly dependent on the particles size of raw tungsten powders and liquid-phase sintering temperature.
基金Project([2006]112) supported by the Transformation of the Scientific and Technological Achievement of the Colleges in Guangdong Province, China
文摘The flow behavior of feedstock for the tungsten alloy powder in the mold cavity was approximately described using Hele-Shaw flow model. The math model consisting of momentum equation, consecutive equation and thermo-conduction equation for describing the injection process was established. The equations are solved by the finite element/finite difference hybrid method that means dispersing the feedstock model with finite element method, resolving the model along the depth with finite difference method, and tracking the movable boundary with control volume method, then the pressure equation and energy equation can be resolved in turn. The numerical simulation of the injection process and the identification of the process parameters were realized by the Moldflow software. The results indicate that there is low temperature gradient in the cavity while the pressure and shear rate gradient are high at high flow rate. The selection of the flow rate is affected by the structure of the gate. The shear rate and the pressure near the gate can be decreased by properly widening the dimension of the gate. There is a good agreement between the process parameters obtained by the numerical simulation and the actual ones.
