Short residence time of the sorbent in the gas stream and formation of a dense layer of reaction product surrounding its surface influence the sulfur removal efficiency. A practical means of improving the process perf...Short residence time of the sorbent in the gas stream and formation of a dense layer of reaction product surrounding its surface influence the sulfur removal efficiency. A practical means of improving the process performance is to employ fluidized bed reaction in replacement of entrained bed reaction on normally used in cool side desulfurizaiton. This paper describes cold modeling study of a circulating fluidized bed reactor. Several aspects of the problem are discussed: fluidization behavior of CaO, attrition of the sorbent and solids entrainment from the fluidized bed. Mechanisms and key controlling parameters are identified, and an integral model based on rate of attrition and mass balance is developed for predicting steady state mass flows and particle size distributions of the system. A process flow scheme is finally presented for conducting desulfurization tests in the second stage of the study.展开更多
The influence of H2O (g) content in circulating flue gas on sintering was studied by simulating the flue gas circulating sintering. The results show that the burning speed of solid fuel and the heat transfer rate du...The influence of H2O (g) content in circulating flue gas on sintering was studied by simulating the flue gas circulating sintering. The results show that the burning speed of solid fuel and the heat transfer rate during sintering process are improved when the H2O (g) content increases from 0 to 6%, which accelerates the sintering speed. However, when the H2O (g) content exceeds 6 %, the over-wet zone in sinter bed is thickened, which deteriorates the permeability of sintering bed. In addition, the magnetite content in sinter increases, while the acicular calcium ferrite content decreases. Accordingly, the sinter yield and tumble index decrease with excessive H2O (g) content. To guarantee the yield and quality of sinter, the favourable H2O (g) content in circulating flue gas should be controlled to be less than 6%.展开更多
Circulating flue gas can reduce the emission of flue gas , and furthermore , it can reuse the waste heat effectively in the sintering process.Compared with conventional sintering , O2 that gets through the sintering b...Circulating flue gas can reduce the emission of flue gas , and furthermore , it can reuse the waste heat effectively in the sintering process.Compared with conventional sintering , O2 that gets through the sintering bed decreases because of substituting circulating gas for air.The influences of O2 content on sintering process are studied through simulating the flue gas circulation sintering with artificial gas.It shows that , with the reducing of O2 content in circulating gas , the combustion speed of fuel decreases and incomplete combustion degree increases , which makes the flame front fall behind the heat front and reduces the heat utilization efficiency of fuel.The ultimate result is that the temperature of sintering bed decreases and the liquid phase reduces.In addition , the reducing atmosphere is strengthened because of flue gas circulation , which makes the magnetite increase yet calcium ferrite reduce gradually. Because the content of calcium ferrite with good strength reduces , the sinter yield and tumble strength decrease.To ensure the sinter index , the favorable O2 content of circulating flue gas is no less than 15%.展开更多
The oxidizing highly reactive absorbent was prepared from fly ash,industry lime,and an oxidizing additive M.Experiments of simultaneous desulfurization and denitrification were carried out in a flue gas circulating fl...The oxidizing highly reactive absorbent was prepared from fly ash,industry lime,and an oxidizing additive M.Experiments of simultaneous desulfurization and denitrification were carried out in a flue gas circulating fluidized bed(CFB).The effects of influencing factors and calcium availability were also investigated on the removal efficiencies of desulfurization and denitrification.Removal efficiencies of 95.5%for SO2 and 64.8%for NO were obtained respectively under the optimal experimental conditions. The component of the spent absorbent was analyzed with chemical analysis methods.The results in- dicated that more nitrogen species appeared in the spent absorbent except sulfur species.A scanning electron microscope(SEM)and an accessory X-ray energy spectrometer were used to observe micro-properties of the samples,including fly ash,oxidizing highly reactive absorbent and spent absorbent.The simultaneous removal mechanism of SO2 and NO based on this absorbent was pro- posed according to the experimental results.展开更多
An "Oxygen-enriched" highly reactive absor- bent was prepared by mixing fly ash, lime and a small quantity of KMnO4 for simultaneous desulfiarization and denitrification. Removal of SO2 and NO simultaneously was car...An "Oxygen-enriched" highly reactive absor- bent was prepared by mixing fly ash, lime and a small quantity of KMnO4 for simultaneous desulfiarization and denitrification. Removal of SO2 and NO simultaneously was carried out using this absorbent in a flue gas circulating fluidized bed (CFB). The highest simultaneous removal efficiency, 94.5% of SO2 and 64.2% of NO, was achieved under the optimal experiment conditions. Scanning Electron Microscope (SEM) and Accessory X-ray Energy Spectrometer (EDX) were used to observe the surface characteristics of fly ash, lime, "Oxygen-enriched" highly reactive absorbent and the spent absorbent. An ion chromatograph (IC) and chemical analysis methods were used to determine the contents of sulfate, sulfite, nitrate and nitrite in the spent absorbents, the results showed that sulfate and nitrite were the main products for desulfurization and denitrification respectively. The mechanism of removing SO2 and NO simultaneously was proposed based on the analysis results of SEM, EDX, IC and the chemical analysis methods.展开更多
文摘Short residence time of the sorbent in the gas stream and formation of a dense layer of reaction product surrounding its surface influence the sulfur removal efficiency. A practical means of improving the process performance is to employ fluidized bed reaction in replacement of entrained bed reaction on normally used in cool side desulfurizaiton. This paper describes cold modeling study of a circulating fluidized bed reactor. Several aspects of the problem are discussed: fluidization behavior of CaO, attrition of the sorbent and solids entrainment from the fluidized bed. Mechanisms and key controlling parameters are identified, and an integral model based on rate of attrition and mass balance is developed for predicting steady state mass flows and particle size distributions of the system. A process flow scheme is finally presented for conducting desulfurization tests in the second stage of the study.
基金Item Sponsored by National Natural Science Foundation of China(51174253)Graduate Student Innovation Projects of Central South University of China(2014zzts276)
文摘The influence of H2O (g) content in circulating flue gas on sintering was studied by simulating the flue gas circulating sintering. The results show that the burning speed of solid fuel and the heat transfer rate during sintering process are improved when the H2O (g) content increases from 0 to 6%, which accelerates the sintering speed. However, when the H2O (g) content exceeds 6 %, the over-wet zone in sinter bed is thickened, which deteriorates the permeability of sintering bed. In addition, the magnetite content in sinter increases, while the acicular calcium ferrite content decreases. Accordingly, the sinter yield and tumble index decrease with excessive H2O (g) content. To guarantee the yield and quality of sinter, the favourable H2O (g) content in circulating flue gas should be controlled to be less than 6%.
基金Item Sponsored by National Natural Science Foundation of China ( 51174253 )Fundamental Research Funds for Central Universities of China ( NCET-05-0630 )Graduate Student Degree Thesis Innovation Foundation of Hunan Province of China (1343/74333001114)
文摘Circulating flue gas can reduce the emission of flue gas , and furthermore , it can reuse the waste heat effectively in the sintering process.Compared with conventional sintering , O2 that gets through the sintering bed decreases because of substituting circulating gas for air.The influences of O2 content on sintering process are studied through simulating the flue gas circulation sintering with artificial gas.It shows that , with the reducing of O2 content in circulating gas , the combustion speed of fuel decreases and incomplete combustion degree increases , which makes the flame front fall behind the heat front and reduces the heat utilization efficiency of fuel.The ultimate result is that the temperature of sintering bed decreases and the liquid phase reduces.In addition , the reducing atmosphere is strengthened because of flue gas circulation , which makes the magnetite increase yet calcium ferrite reduce gradually. Because the content of calcium ferrite with good strength reduces , the sinter yield and tumble strength decrease.To ensure the sinter index , the favorable O2 content of circulating flue gas is no less than 15%.
基金the Significant Pre-research Foundation of North China Electric PowerUniversity(D03-035)
文摘The oxidizing highly reactive absorbent was prepared from fly ash,industry lime,and an oxidizing additive M.Experiments of simultaneous desulfurization and denitrification were carried out in a flue gas circulating fluidized bed(CFB).The effects of influencing factors and calcium availability were also investigated on the removal efficiencies of desulfurization and denitrification.Removal efficiencies of 95.5%for SO2 and 64.8%for NO were obtained respectively under the optimal experimental conditions. The component of the spent absorbent was analyzed with chemical analysis methods.The results in- dicated that more nitrogen species appeared in the spent absorbent except sulfur species.A scanning electron microscope(SEM)and an accessory X-ray energy spectrometer were used to observe micro-properties of the samples,including fly ash,oxidizing highly reactive absorbent and spent absorbent.The simultaneous removal mechanism of SO2 and NO based on this absorbent was pro- posed according to the experimental results.
文摘An "Oxygen-enriched" highly reactive absor- bent was prepared by mixing fly ash, lime and a small quantity of KMnO4 for simultaneous desulfiarization and denitrification. Removal of SO2 and NO simultaneously was carried out using this absorbent in a flue gas circulating fluidized bed (CFB). The highest simultaneous removal efficiency, 94.5% of SO2 and 64.2% of NO, was achieved under the optimal experiment conditions. Scanning Electron Microscope (SEM) and Accessory X-ray Energy Spectrometer (EDX) were used to observe the surface characteristics of fly ash, lime, "Oxygen-enriched" highly reactive absorbent and the spent absorbent. An ion chromatograph (IC) and chemical analysis methods were used to determine the contents of sulfate, sulfite, nitrate and nitrite in the spent absorbents, the results showed that sulfate and nitrite were the main products for desulfurization and denitrification respectively. The mechanism of removing SO2 and NO simultaneously was proposed based on the analysis results of SEM, EDX, IC and the chemical analysis methods.