Equivalent Noise Models in Fiber Optical Communication Systems

An equivalent noise model of optical receiver amplifiers as shown in Fig.1 has been given in many fiber optical communication literatures. It is proved in this paper that this equivalent noise model is neither equivalent to the original one nor measurable. The main reason is that the position of the input impedance in this noise model is not the same with its in the typical noise model,but the same S vn , S in with the typical noise model are used. So the equivalent noise model above is wrong and is not fit to be taken into application.

Optimization of Spectral Inverters in Optical Fiber Communication Systems with Mid-Span Spectrum Inversion

In this paper, signal distortions caused by spectral inverters which are used in 10Gb/s optical fiber communication systems with mid span spectrum inversion in terms of dispersion shift fibers are analyed numerically. It is shown that there exist the optimal input signal power, fiber length and fiblter bandwidth for the spectral in verters. System transmission penalty can be minimized by optimizing these parameters.

Toward Low-Cost Flexible Intelligent OAM in Optical Fiber Communication Networks

Low-cost,flexible and intelligent optical performance monitoring and management is a key enabling technology for network quality guarantee,especially in the era of explosive growth of communication capacity and network scale.However,to the best of our knowledge,it is extremely challenging to implement real-time performance monitoring and operations,administration and maintenance(OAM) in a highly complex dynamic network.In this paper,we propose an innovative optical identification(OID) scheme that can realize both performance monitoring and some advanced OAM sub-functions.The basic concepts,applications,challenges and evolution directions of this OID tool are also discussed.

Polarization Jitters Caused by Fiber Nonlinearity in PM Optical Communication System

The phenomenon of polarization jitters caused by fiber nonlinearity is investigated. A general formula about the polarization jitter is concluded in polarization multiplexing (PM) system based on two orthogonal linear polarization states when the best polarization correction is used. A 100 Gb/s PM system based on NRZ code is investigated by simulation, and the Stocks parameter about polarization jitter and Poincare sphere diagrams are got for different power and phase difference of two orthogonal polarized light. The results show that the polarization jitters will be suppressed when the combined PM signal is the linear or circular polarization state.

Fiber Grating Ring Laser in All Optical Communication System

Erbium fiber grating ring laser (EFRL) witn an integrated travelling wave and low polarization mode noise is reported. Through modulated experiment of a successful 2.488 Gb/s RZ data, it is shown that the EFRL is a promising alternative to DFB lasers for high-speed transmission applications.

Spatial Mode-Division Multiplexing for High-Speed Optical Coherent Detection Systems

Spatial modedivision multiplexing is emerging as a potential solution to further increasing optical fiber capacity and spectral efficiency. We report a dualmode, dualpolarization transmission method based on modeselective excitation and detection over a twomode fiber. In particular, we present 107 Gbit/s coherent optical OFDM （COOFDM） transmission over a 4.5 km twomode fiber using LP and LP. modes in which mode separation is performed optically.

Recent progress on high-speed optical transmission

The recently reported high spectral efficiency （SE） and high-baud-rate szgnal transmission are all Daseo on digital coherent optical communications and digital signal processing （DSP）. DSP simplifies the re- ception of advanced modulation formats and also enables the major electrical and optical impairments to be processed and compensated in the digital domain, at the transmitter or receiver side. In this paper, we summarize the research progress on high-speed signal generation and detection and also show the progress on DSP for high-speed signal detection. We also report the latest progress on multi-core and multi-mode multiplexing.

Nonbinary LDPC BICM for Next-Generation High-Speed Optical Transmission Systems

We propose a nonbinary byte-interleaved coded-modulation scheme with inner and outer turbo-like iterative decoder.The net coding gain is 0.6 d B higher than the state-of-the-art binary single parity check(SPC)low-density parity-check(LDPC)based turbo-product counterpart,with adjustable iterations and lower error-floor.We provide the details of Bahl-CockeJelinek-Raviv(BCJR)based inner code decoder and optimum signal constellation design(OSCD)method in this paper.The single-mode fiber(SMF)channel simulation is also discussed.

Dispersion Monitoring Techniques in High Bit-rate Optical Communication Systems

For the efficient dynamic dispersion compensation, it is essential to monitor the dispersion accurately. The existing main dispersion monitoring techniques in high bit-rate optical communication systems are presented as well as their operating principles and research progress. The advantages and disadvantages of these methods are analyzed and discussed.

Detecting Threats of Acoustic Information Leakage Through Fiber Optic Communications

Information leaks through regular fiber optic communications is possible in the form of eavesdropping on conversations, using standard fiber optic communications as illegal measuring network. The threat of leakage of audio information can create any kind of irregular light emission, as well as regular light beams modulated at acoustic frequencies. For information protection can be used a means of sound insulation, filtration and noising. This paper discusses the technical possibilities of countering threats by monitoring the optical radiation to detect eavesdropping.

2.5 Gbit/s monolithic ICs for optical fiber transmitter and receiver in 0.35 μm CMOS process

2.5 Gbit/s monolithic integrated circuits （ICs） for optical fiber transmitter and receiver in 0.35 μm CMOS （complementary metal-oxide-semiconductor transistor） process are presented. The transmitter, which includes a 4： 1 multiplexer and a laser diode driver （LDD）, has four 622 Mbit/s random signals as its inputs and gets a 2.5 Gbit/s driving signal as its output; the receiver detects a 2.5 Gbit/s random signal and gets four 622 Mbit/s signals at the output. The main circuits include a trans-impedance amplifier （TIA）, a limiting amplifier, a clock and data recovery （CDR） unit, and a 1： 4 demultiplexer （DEMUX）. Test results prove the logic functions of the transmitter to be right, and the 10% to 90% rise and fall times of transmitter＇s output data eye diagram are 211.1 ps and 200 ps, respectively. The sensitivity of the receiver is measured to be better than 20 mV. The root mean square jitter of the DEMUX＇s output data is 15.6 ps and that of the clock after 1： 4 frequency dividing is 1.9 ps. Two chips are both applicable to 2.5 Gbit/s optical fiber communication systems.

Health Monitoring of Long-Haul Fiber Communication System Using Chaotic OTDR

A novel chaotic optical time-domain reflectometry(OTDR)-based approach was proposed for monitoring long-haul fiber communication systems with multiple fiber segments. The self-phase modulation and group velocity dispersion effects of the optical cable was considered in demonstrating the proof-of-concept experiment and simulation. In experiments, the correlation peaks are clearly obtained from the correlation trace between the reference and reflected(or scattered) light signals propagating in three optical-fiber segments. The technique affords a high spatial resolution of 2 m, and further long-haul fiber simulations indicate that the sensing distance can be more than 3300 km. Thus, the new proposed technique can be effectively applied for health monitoring of long-haul fiber communication systems.

Research on Additional Loss of Guidance Optical Fiber

The factors which cause additional losses of guidance optical fiber in wound state were analyzed.A mathematical model used to analyze the macro-bend losses in the cross region producing in the precision winding process was established.For an actual guidance optical fiber,the measured data of the fiber's additional losses under low temperature and the loss curves with radius were given in the paper.The simulation results were compared with the test data.It shows that the additional losses of optical fiber caused by bending and low temperature can meet the actual requirements of the fiber optical guidance system.The established model can be used to predict the change trend of fiber losses in the winding process with a certain tensile force.

FAST EVALUATION OF THE CHARACTERISTICS OF SINGLE-MODE OPTICAL FIBERS

This paper describes a method for fast engineering evaluation of the transmission characteristicsof single-mode optical fibers.A versatile microcomputer program is presented which can be utilized to ana-lyze mode field characteristics of single-mode fibers with arbitrary refractive index profiles.Our computationshows that the mathematical algorithm and the corresponding programs developeod in this paper are rela-tively simple and accurate enough for the engineenring design of single-mode fibers for optical communica-tion systems.

Remote I/O Unit for Optical Fiber Demmunication

Abstract:Based on optical fiber technology, the main electric circuit of the remote I/O unit controller is studied. And the application of the system is illustrated.

STUDY ON MINE FIRE-RESISTANT OPTICAL FIBER CABLE KL5004

This paper introduces a new-developed mine fire-resistant optical fiber cable (OFC)KL5004,its structural characteristics, main feature, the theory about fire resistance and its application in high output and efficiency mine.

Design and Implementation of Optical Fiber Test Equipment

In order to meet the needs of the rapid development of optical fiber communication technology, combined with the thinking of the Internet of Things, a new idea of designing an optical fiber test equipment using Raspberry Pi is proposed. At the same time, the design of a multi-parameter measuring device for optical fiber signals based on Flask was completed.

Applied electric field to fabricate colloidal crystals with the photonic band-gap in communication waveband

The macropore silica colloidal crystal templates were assembled orderly in a capillary glass tube by an applied electric field method to control silica deposition. In order to achieve the photonic band gap （PBG） of colloidal crystal in optical communication waveband, the diameter of silica microspheres is selected by Bragg diffraction formula. An experiment was designed to test the bandgap of the silica crystal templates. This paper discusses the formation process and the close-packed fashion of the silica colloidal crystal templates was discussed. The surface morphology of the templates was also analyzed. The results showed that the close-packed fashion of silica array templates was face-centered cubic （FCC） structure： The agreement is very good between the experimental data and the theoretical calculation.

Beyond 100 Gb/s Optical OFDM Transmitted in Optical Long-Haul System

100 G Ethernet is considered to become the next generation Ethernet standard for IP networks.Typical 100 Gb/s transmission systems and their performance are presented.Comparision and analysis for 100 Gb/s transmission systems have been discussed.It is demonstrated that optical OFDM can be used in future 100 Gb/s/ch and long-haul system.