Mechanical Properties and Durability of Sustainable Concrete Manufactured Using Ceramic Waste:A Review

Green and sustainable concrete has attracted significant attention from the construction industry and researchers since it was proposed.The ceramic waste materials are often directly buried in the ground or placed in an open dump,and the accumulation of ceramic waste contributes to environmental pollution,which makes the recycling of ceramic waste quite urgent.Owing to the pozzolanic activity,excellent mechanical properties and durability,industrial ceramic waste is considered as a suitable substitute for cement or natural aggregates to fabricate renewable concrete.In this paper,the pozzolanic activity of ceramic waste and the workability,mechanical performance,and durability of ceramic concrete are discussed.In addition,the most recent research results pertaining to ceramic concrete are reviewed.Ground ceramic powder improves the workability,compressive strength,resistance to chloride penetration,and carbonation resistance of concrete to a certain extent.Concrete containing ceramic as the aggregate has a lower mechanical performance than ordinary concrete.However,the resistance to chloride penetration,freeze-thaw resistance,and high-temperature resistance of ceramic concrete are remarkable.Ceramic concrete is environmentally friendly,requires fewer energy resources to manufacture than ordinary concrete,and has excellent engineering properties.However,further research is required for future engineering applications.

Ceramic Setting Phosphate Binders for Bonding Refractory Concretes

The ceramic setting binders obtained by means of the raw mix mechano-chemical processing(mechanical dispersion and chemical interaction processes combination), used for bonding refractory concretes, become more available with a subsequent increased interest in their properties because they develop initial strength during a heat up of the units within 8-10 h, in contrast to 24 h after placement for high Al_2O_3 cements(HAC). This strength development enables high temperature processing units to be relined with minimum turnaround time, thus providing a favored cost/performance ratio. The present paper identifies the predominant phosphate phases responsible for developing good mechanical-strength properties of zirconia and alumina concretes bonded with mechano-chemical binders. It sets out the colloid and crystalline phases resulted from interphase interaction that provide the basis for high concentrated bonding suspensions(HCBS) technology useful to the refractory industry.

Basic Properties of Concrete Incorporating Recycled Ceramic Aggregate and Ultra-fine Sand

Recycled ceramic mixed sand（RCMS） was obtained by partially replacing ultra-fine sand with recycled ceramic coarse sand（RCCS）. The effects of RCCS replacement rate on the apparent density, workability, compressive strength and splitting tensile strength of recycled ceramic concrete（RCC） were investigated. In addition, the relationship between the water-cement ratio and compressive strength of RCC was also studied. The experimental results indicate that the reusing of recycled ceramic aggregate can improve the cohesiveness and water retentiveness of fresh concrete and benefit the mechanical properties development. When the RCCS replacement rate is not less than 40%, the mechanical properties of RCC are superior to those of the reference concrete. Moreover, when recycled ceramic medium sand was completely used as fine aggregate, the maximum increase in both compressive strength and splitting tensile strength were obtained, comparing with those of reference concrete, the increment ratio was 19.85% and 32.73%, respectively. The microscopic analysis shows that the using of recycled ceramic aggregate can meliorate distinctly the structure of the interfacial transition zone（ITZ） and increase the compaction degree of cement paste. Furthermore, an expression of the compressive strength of RCC and the cement-water ratio is regressed and gains a good linear relativity. It is an effective way to recycle waste ceramic, and the consumption of recycled ceramic aggregate could reach from 26.9% to 47.6% of the total weight of aggregate in producing concrete.

Mechanical and Microstructural Analysis of Waste Ceramic Optimal Concrete Reinforced by Hybrid Fibers Materials: A Comprehensive Study

Combining different types of fibers inside a concrete mixture was revealed to improve the strength properties of cementitious matrices by monitoring crack initiation and propagation.The contribution of hybrid fibers needs to be thoroughly investigated,considering various parameters such as fibers type and content.The present study aims to carry out some mechanical and microstructural characteristics of Waste Ceramic Optimal Concrete(WOC)reinforced by hybrid fibers.Reinforcement materials consist of three dif­ferent fiber types:hook-ended steel fiber(HK),crimped steel fiber(CR)and polyvinyl alcohol(PVA)fibers and the effect of their addition on the waste ceramic composites’mechanical behaviour.Furthermore,a micro­structural analysis was carried out to understand the waste ceramic matrix composition and its bonding to hybrid fibers.Results showed that the ad­dition of hybrid fibers improved the strength characteristics of the ceramic waste composites.For instance,the existence of PVA-CR increased the tensile and flexural strength of the waste ceramic composite by 85.44%and 70.37%,respectively,with respect to the control sample(WOC).As well as hybrid fiber exhibits improved morphological properties as a result of in­creased pore filling with dense and compact structure,as well as increased C-H crystals and denser structure in pastes as a result of the incorporation of hybrid fibers into the concrete mix.The present experimental research shows the choice of using steel fiber with PVA as a reinforcement material.The idea of adding hybrid fiber is to prepare the economic,environmental,and technological concrete.Moreover,it offers a possibility for improving concrete’s durability,which is vital.Finally,it was concluded that steel fiber is more durable,and stiffer and provides adequate first crack strength and ultimate strength.In contrast,the PVA fiber is relatively flexible and improves the post-crack zone’s toughness and strain capacity.

Effects of Manufactured-sand on Dry Shrinkage and Crccp of High-strength Concrete

The influences of natural sand, manufactured-sand （MS） and stone-dust （SD） in the manufactured-sand on workability, compressive strength, elastic modulus, drying shrinkage and creep properties of high-strength concrete （HSC） were tested and compared. The results show that the reasonable content （7%-10.5%） of SD in MS will not deteriorate the workability of MS-HSC. It could even improve the workability. Moreover, the compressive strength increases gradually with the increasing SD content,and the MS- HSC with low SD content （smaller than 7%） has the elastic modulus which approaches that of the natural sand HSC, but the elastic modulus reduces when the SD content is high. The influence of the SD content on drying shrinkage performance of MS-HSC is closely related to the hydration age. The shrinkage rate of MS-HSC in the former 7 d age is higher than that of the natural sand HSC, but the difference of the shrinkage rate in the late age is not marked. Meanwhile the shrinkage rate reduces as the fly ash is added; the specific creep and creep coefficient of MS-HSC with 7% SD are close to those of the natural sand HSC.

Seismic Performance of High-Strength Short Concrete Column with High-Strength Stirrups Constraints

The seismic performance of four short concrete columns was investigated under low cycle and repeated loads, including the failure characteristics, hysteretic behavior, rigidity degeneracy and steel-bar stress. The influences of reinforcement strength, stirrup ratio and shear span ratio were also compared. Test results reveal that the restriction effect of stirrups can improve the peak stress, so the bearing capacity of specimen can be improved; for the high-strength short concrete column with high-strength stirrups, it was more reasonable to use ultimate displacement angle to reflect the ductility of the specimen, and the yield strength of high-strength stirrups should be devalued when calculating the stirrup characteristic value; the seismic performance of short column would be improved with the increase of volume–stirrup ratio and shear span ratio;the high-strength stirrups and high-strength longitudinal reinforcements did not yield when the load acting on the specimen reached the peak value, which brought adequate safety stock to these short columns.

Experimental and Numerical Analysis of High-Strength Concrete Beams Including Steel Fibers and Large-Particle Recycled Coarse Aggregates

In order to study the performances of high-strength concrete beams including steel fibers and large-particle recycled aggregates,four different beams have been designed,tested experimentally and simulated numerically.As varying parameters,the replacement rates of recycled coarse aggregates and CFRP(carbon fiber reinforced polymer)sheets have been considered.The failure mode of these beams,related load deflection curves,stirrup strain and shear capacity have been determined through monotonic loading tests.The simulations have been conducted using the ABAQUS finite element software.The results show that the shear failure mode of recycled concrete beams is similar to that of ordinary concrete beams.The shear carrying capacity of high-strength concrete beams including steel fibers and large-particle recycled coarse aggregates grows with an increase in the replacement rate of recycled coarse aggregates.Reinforcement with CFRP sheets can significantly improve the beam’s shear carrying capacity and overall resistance to deformation.

FAILURE MODE AND CONSTITUTIVE MODEL OF PLAIN HIGH-STRENGTH HIGH-PERFORMANCE CONCRETE UNDER BIAXIAL COMPRESSION AFTER EXPOSURE TO HIGH TEMPERATURES

An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete （HSHPC） under biaxial compression is developed. It is based on the experiments performed for characterizing the strength and deformation behavior at two strength levels of HSHPC at 7 different stress ratios including a=σs ： σ3=0.00：-1,-0.20：-1,-0.30 ： -1,-0.40：-1,-0.50：-1,-0.75：-1,-1.00：-1, after the exposure to normal and high temperatures of 20, 200, 300, 400, 500 and 600℃, and using a large static-dynamic true triaxial machine. The biaxial tests were performed on 100 mm×100 mm×100 mm cubic specimens, and friction-reducing pads were used consisting of three layers of plastic membrane with glycerine in-between for the compressive loading plane. Based on the experimental results, failure modes of HSHPC specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured; and the influence of the temperature and stress ratios on them was also analyzed. The experimental results showed that the uniaxial compressive strength of plain HSHPC after exposure to high temperatures does not decrease dramatically with the increase of temperature. The ratio of the biaxial to its uniaxial compressive strength depends on the stress ratios and brittleness-stiffness of HSHPC after exposure to different temperature levels. Comparison of the stress-strain results obtained from the theoretical model and the experimental data indicates good agreement.

Nonlinear fi nite element analysis of high-strength concrete columns and experimental verification

This paper describes a nonlinear finite element （FE） analysis of high strength concrete （HSC） columns, and verifies the results through laboratory experiments. First, a cyclically lateral loading test on nine cantilever column specimens of HSC is described and a numerical simulation is presented to verify the adopted FE models. Next, based on the FE model for specimen No.6, numerical simulations for 70 cases, in which different concrete strengths, stirrup ratios and axial load ratios are considered, are presented to explore the effect of these parameters on the behavior of the HSC columns, and to check the rationality of requirements for these columns specified in the China Code for Seismic Design of Buildings （GB 50011- 2001）. In addition, three cases with different stirrup strengths are analyzed to investigate their effect on the behavior of HSC columns. Finally, based on the numerical results some conclusions are presented.

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.

Strength Regularity and Failure Criterion of High-Strength High-Performance Concrete under Multiaxial Compression

Multiaxial compression tests were performed on 100 mm×100 mm×100 mm high-strength high-performance concrete （HSI-IPC） cubes and normal strength concrete （NSC） cubes. The failure modes of specimens were presented, the static compressive strengths in principal directions were measured, the influence of the stress ratios was analyzed. The experimental results show that the ultimate strengths for HSHPC and NSC under multiaxial compression are greater than the uniaxial compressive strengths at all stress ratios, and the multiaxial strength is dependent on the brittleness and stiffness of concrete, the stress state and the stress ratios. In addition, the Kupfer-Gersfle and Ottosen＇s failure criteria for plain HSHPC and NSC under multiaxial compressive loading were modified.

CT Image-based Analysis on the Defect of Polypropylene Fiber Reinforced High-Strength Concrete at High Temperatures

With the application of X-ray computed tomography（CT） technology of C80 high-strength concrete with polypropylene fiber at elevated temperatures, the microscopic damage evolution process observation and image building could be obtained, based on the statistics theory and numerical analysis of the combination of concrete internal defects extension and evolution regularity of microscopic structure. The expermental results show that the defect rate has changed at different temperatures and can determine the concrete degradation threshold temperatures. Also, data analysis can help to establish the evolution equation between the defect rate and the effect of temperature damage, and identify that the addition of polypropylene fibers in the high strength concrete at high temperature can improve cracking resistance.

Pseudo-dynamic test and numerical simulation of high-strength concrete frame structure reinforced with high-strength rebars

This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.

Seismic behavior of multiple reinforcement,high-strength concrete columns:experimental and theoretical analysis

This study investigates the seismic performance of multiple reinforcement,high-strength concrete(MRHSC)columns that are characterized by multiple transverse and longitudinal reinforcements in core areas.Eight MRHSC columns were designed and subjected to a low cycle,reversed loading test.The response,including the failure modes,hysteretic behavior,lateral bearing capacity,and displacement ductility,was analyzed.The effects of the axial compression ratio,stirrup form,and stirrup spacing of the central reinforcement configuration on the seismic performance of the columns were studied.Furthermore,an analytical model was developed to predict the backbone force-displacement curves of the MRHSC columns.The test results showed that these columns experienced two failure modes:shear failure and flexure-shear failure.As the axial compression ratio increased,the bearing capacity increased significantly,whereas the deformation capacity and ductility decreased.A decrease in the spacing of central transverse reinforcements improved the ductility and delayed the degradation of load-bearing capacity.The proposed analytical model can accurately predict the lateral force and deformations of MRHSC columns.

Elasto-plastic Analysis of High-strength Concrete Shear Wall with Boundary Columns Using Fiber Model

In this study,an experimental study and numerical calculations using fiber model were conducted for four high-strength concrete shear walls with boundary columns under low cyclic load.The boundary column and shear wall were divided into fiber elements,and PERFORM-3D finite element analysis software was used to carry out push-over analysis on the test specimens.The results show that the finite element analysis results were in good agreement with the experimental results.The proposed analysis method could perform elasto-plastic analysis on the high-strength concrete shear wall with boundary columns without distinguishing the categories of frame column and shear wall.The seismic performance of high-strength concrete shear wall with boundary columns was analyzed using the following parameters:axis compression ratio,height to width ratio,ratio of vertical reinforcement,and ratio of longitudinal reinforcement in the boundary column.The results show that the increase in the axial compression ratio causes the bearing capacity of the shear wall to increase at first and then to decrease and causes the ductility to decrease.The increase in the height to width ratio causes the bearing capacity of the shear wall to decrease and its ductility to increase.The ratio of vertical reinforcement was found to have little effect on the bearing capacity and ductility.The increase in the ratio of longitudinal reinforcement in boundary column resulted in a significant increase in the bearing capacity and caused the ductility to decrease at first and then to slowly increase.

Detection of Thermophysical Properties for High Strength Concrete after Exposure to High Temperature

Using the detection principle of infrared thermal imaging technique and the detection principle of DRH thermal conductivity tester laboratory,we investigated the infrared thermal image inspection,coefficient of thermal conductivity,apparent density,and compressive strength test on C80 high-strength concrete（HSC） in the presence and absence of polypropylene fibers under completely heated conditions.Only slight damages were detected below 400 ℃,whereas more and more severe deterioration events were expected when the temperature was above 500 ℃.The results show that the elevated temperature through infrared images generally exhibits an upward trend with increasing temperature,while the coefficient of thermal conductivity and apparent density decrease gradually.Additionally,the addition of polypropylene fibers with appropriate length,diameter,and quantity contributes to the improvement of the high-temperature resistance of HSC.

A Numerical Stress-strain Response Model of All Grades of Concretes under Uniaxial Compression

An important problem facing stress-strain response modeling of concrete is the complexity of the compressive strength grades. 21 groups of speeimens with different cubic compressive strength （56.3- 164.9 MPa ） hate beets numerically analyzed. Using only the compressive strength, a stress-strain response model of different concrete grade was established. The numerical simulation model not only qualitatively reproduces the relationship of uniaxial compressive strength, peak value stress and cubic compressive strength, but realizes the consistence of the ascending branch of stress-strain cunts with different strength grades by introducing the correction coefficient k. The results indicate k increases gradually from 0 to approximate 1 with the increase of the compressive strength, corresponding to the transition from the paracurve to straight line branch in stress-strain curves. When k is 0, the madel is identical to the Hognestad equation. A good agreement with the experiment data was obtained.

Formulating for Innovative Self-Compacting Concrete with Low Energy Super-Sulfated Cement Used for Sustainability Development

This study proposed a new way to formulate a low energy super-sulfated cement (SSC) which can be used to produce self-compacting concrete (SCC) with high compressive strength and durability in terms of chloride penetration resistance. This innovative SSC, different from the traditional SSC, was purely produced with a ternary mixture of three industrial by-products of ground granulated blast furnace slag, low calcium Class F fly ash and circulating fluidized bed combustion (CFBC) fly ash and was denoted as SFC-SSC (super-sulfated cement made by mixture of slag, Class F fly ash and CFBC fly ash). Experimental results showed that the combination of a fixed amount of 15 wt.% of CFBC fly ash with various ratios of Class F fly ash to slag could be used to produce the hardened SCCs with high 28-day compressive strengths (41.8 - 65.6 MPa). Addition of Class F fly ash led to the resulting SCCs with lowered price and preferable engineering properties, and thus it was considered as state-of-the-art method to drive such type of concrete towards sustainable construction materials.

活化煤废料替代水泥制备混凝土的基本特性

这是一篇陶瓷及复合材料领域的论文。为探索煤废料替代水泥进行混凝土制备的可行性,利用活性化处理的煤渣粉和煤矸石粉按照0、10%、20%、30%和40%的比例替代水泥进行混凝土试样的制备并对混凝土试样的坍落度、抗压和抗折强度进行测试,同时耐高温性能实验,结果证明:随着替代比的增加,坍落度、抗压强度和抗折强度均先增后减;煤废料的较优替代比为20%~30%。活化煤渣粉试样的早期强度增长率大;而活化煤矸石粉试样的长期强度增长率较大。当水灰比=0.45时,试样的抗压强度随着温度的升高先增后减,在100℃时达到极大值;当水灰比=0.5时,混凝土试样的抗压强度均随着温度的升高逐渐降低;活性煤渣粉试样界面区域的水合胶结构较最多,对照组次之,活化煤矸石粉试样较少。随着温度升高,试样表面的孔隙和裂缝明显增多且破坏面的破碎程度逐渐加剧。