ENERGY-SAVING MATCHING STRATEGY AND EXPERIMENTAL STUDY OF PUMPING SYSTEM FOR TRUCK-MOUNTED CONCRETE PUMP

Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.

Application of Large-diameter and Long-span Micro-expansive Pumping Concrete Filled Steel Tube Arch Bridge

In this article the high strength micro-expansive concrete that has been applied on big-diameter and long-span steel arch bridge is researched. The applications show that the concrete has some merits, such as good fluidity, low bleeding ratio and no segregation, low slump loss, high early strength and high later strength, micro-expansion etc.

Effects of Manufactured-sand on Dry Shrinkage and Crccp of High-strength Concrete

The influences of natural sand, manufactured-sand （MS） and stone-dust （SD） in the manufactured-sand on workability, compressive strength, elastic modulus, drying shrinkage and creep properties of high-strength concrete （HSC） were tested and compared. The results show that the reasonable content （7%-10.5%） of SD in MS will not deteriorate the workability of MS-HSC. It could even improve the workability. Moreover, the compressive strength increases gradually with the increasing SD content,and the MS- HSC with low SD content （smaller than 7%） has the elastic modulus which approaches that of the natural sand HSC, but the elastic modulus reduces when the SD content is high. The influence of the SD content on drying shrinkage performance of MS-HSC is closely related to the hydration age. The shrinkage rate of MS-HSC in the former 7 d age is higher than that of the natural sand HSC, but the difference of the shrinkage rate in the late age is not marked. Meanwhile the shrinkage rate reduces as the fly ash is added; the specific creep and creep coefficient of MS-HSC with 7% SD are close to those of the natural sand HSC.

Seismic Performance of High-Strength Short Concrete Column with High-Strength Stirrups Constraints

The seismic performance of four short concrete columns was investigated under low cycle and repeated loads, including the failure characteristics, hysteretic behavior, rigidity degeneracy and steel-bar stress. The influences of reinforcement strength, stirrup ratio and shear span ratio were also compared. Test results reveal that the restriction effect of stirrups can improve the peak stress, so the bearing capacity of specimen can be improved; for the high-strength short concrete column with high-strength stirrups, it was more reasonable to use ultimate displacement angle to reflect the ductility of the specimen, and the yield strength of high-strength stirrups should be devalued when calculating the stirrup characteristic value; the seismic performance of short column would be improved with the increase of volume–stirrup ratio and shear span ratio;the high-strength stirrups and high-strength longitudinal reinforcements did not yield when the load acting on the specimen reached the peak value, which brought adequate safety stock to these short columns.

Performances of the High Strength Low Heat Pump Concrete (HLPC)

The effects of mineral admixtures on fluidity,mechanical and hydrational exothermic behavior were studied.The results show that,double adding ways,i e,fly ash and slag were added at the same time,not only improves the fluidity of fresh concrete with low W/B and compensates the lower early compressive strength of harden concrete caused by high adding amount of fly ash, but also greatly reduces the highest temperature rise, exothermic rate and total heat liberation of 3 day of binder pastes in HLPC, and postponed the arrival time of the highest temperature rise. HLPC was prepared and applied to project practice successfully.

FAILURE MODE AND CONSTITUTIVE MODEL OF PLAIN HIGH-STRENGTH HIGH-PERFORMANCE CONCRETE UNDER BIAXIAL COMPRESSION AFTER EXPOSURE TO HIGH TEMPERATURES

An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete （HSHPC） under biaxial compression is developed. It is based on the experiments performed for characterizing the strength and deformation behavior at two strength levels of HSHPC at 7 different stress ratios including a=σs ： σ3=0.00：-1,-0.20：-1,-0.30 ： -1,-0.40：-1,-0.50：-1,-0.75：-1,-1.00：-1, after the exposure to normal and high temperatures of 20, 200, 300, 400, 500 and 600℃, and using a large static-dynamic true triaxial machine. The biaxial tests were performed on 100 mm×100 mm×100 mm cubic specimens, and friction-reducing pads were used consisting of three layers of plastic membrane with glycerine in-between for the compressive loading plane. Based on the experimental results, failure modes of HSHPC specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured; and the influence of the temperature and stress ratios on them was also analyzed. The experimental results showed that the uniaxial compressive strength of plain HSHPC after exposure to high temperatures does not decrease dramatically with the increase of temperature. The ratio of the biaxial to its uniaxial compressive strength depends on the stress ratios and brittleness-stiffness of HSHPC after exposure to different temperature levels. Comparison of the stress-strain results obtained from the theoretical model and the experimental data indicates good agreement.

Experimental and Numerical Analysis of High-Strength Concrete Beams Including Steel Fibers and Large-Particle Recycled Coarse Aggregates

In order to study the performances of high-strength concrete beams including steel fibers and large-particle recycled aggregates,four different beams have been designed,tested experimentally and simulated numerically.As varying parameters,the replacement rates of recycled coarse aggregates and CFRP(carbon fiber reinforced polymer)sheets have been considered.The failure mode of these beams,related load deflection curves,stirrup strain and shear capacity have been determined through monotonic loading tests.The simulations have been conducted using the ABAQUS finite element software.The results show that the shear failure mode of recycled concrete beams is similar to that of ordinary concrete beams.The shear carrying capacity of high-strength concrete beams including steel fibers and large-particle recycled coarse aggregates grows with an increase in the replacement rate of recycled coarse aggregates.Reinforcement with CFRP sheets can significantly improve the beam’s shear carrying capacity and overall resistance to deformation.

Nonlinear fi nite element analysis of high-strength concrete columns and experimental verification

This paper describes a nonlinear finite element （FE） analysis of high strength concrete （HSC） columns, and verifies the results through laboratory experiments. First, a cyclically lateral loading test on nine cantilever column specimens of HSC is described and a numerical simulation is presented to verify the adopted FE models. Next, based on the FE model for specimen No.6, numerical simulations for 70 cases, in which different concrete strengths, stirrup ratios and axial load ratios are considered, are presented to explore the effect of these parameters on the behavior of the HSC columns, and to check the rationality of requirements for these columns specified in the China Code for Seismic Design of Buildings （GB 50011- 2001）. In addition, three cases with different stirrup strengths are analyzed to investigate their effect on the behavior of HSC columns. Finally, based on the numerical results some conclusions are presented.

Strength Regularity and Failure Criterion of High-Strength High-Performance Concrete under Multiaxial Compression

Multiaxial compression tests were performed on 100 mm×100 mm×100 mm high-strength high-performance concrete （HSI-IPC） cubes and normal strength concrete （NSC） cubes. The failure modes of specimens were presented, the static compressive strengths in principal directions were measured, the influence of the stress ratios was analyzed. The experimental results show that the ultimate strengths for HSHPC and NSC under multiaxial compression are greater than the uniaxial compressive strengths at all stress ratios, and the multiaxial strength is dependent on the brittleness and stiffness of concrete, the stress state and the stress ratios. In addition, the Kupfer-Gersfle and Ottosen＇s failure criteria for plain HSHPC and NSC under multiaxial compressive loading were modified.

CT Image-based Analysis on the Defect of Polypropylene Fiber Reinforced High-Strength Concrete at High Temperatures

With the application of X-ray computed tomography（CT） technology of C80 high-strength concrete with polypropylene fiber at elevated temperatures, the microscopic damage evolution process observation and image building could be obtained, based on the statistics theory and numerical analysis of the combination of concrete internal defects extension and evolution regularity of microscopic structure. The expermental results show that the defect rate has changed at different temperatures and can determine the concrete degradation threshold temperatures. Also, data analysis can help to establish the evolution equation between the defect rate and the effect of temperature damage, and identify that the addition of polypropylene fibers in the high strength concrete at high temperature can improve cracking resistance.

Pseudo-dynamic test and numerical simulation of high-strength concrete frame structure reinforced with high-strength rebars

This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.

Seismic behavior of multiple reinforcement,high-strength concrete columns:experimental and theoretical analysis

This study investigates the seismic performance of multiple reinforcement,high-strength concrete(MRHSC)columns that are characterized by multiple transverse and longitudinal reinforcements in core areas.Eight MRHSC columns were designed and subjected to a low cycle,reversed loading test.The response,including the failure modes,hysteretic behavior,lateral bearing capacity,and displacement ductility,was analyzed.The effects of the axial compression ratio,stirrup form,and stirrup spacing of the central reinforcement configuration on the seismic performance of the columns were studied.Furthermore,an analytical model was developed to predict the backbone force-displacement curves of the MRHSC columns.The test results showed that these columns experienced two failure modes:shear failure and flexure-shear failure.As the axial compression ratio increased,the bearing capacity increased significantly,whereas the deformation capacity and ductility decreased.A decrease in the spacing of central transverse reinforcements improved the ductility and delayed the degradation of load-bearing capacity.The proposed analytical model can accurately predict the lateral force and deformations of MRHSC columns.

Motion Planning of Concrete Pump Truck with End-Effector's Specified Path

For motion planning of concrete pump truck( CPT) with end-effector's hosepipe path, this paper sets up the mathematic model,including definition of its motion planning,description of its state in C space( configuration space) and its path length. An advanced rapidly-exploring random trees( RRT) algorithm is proposed, in which each tracing point dispersed from the end hosepipe path can map multi-states of CPT so as to make variety of motion path of CPT. For increasing search efficiency and motion path quality,this algorithm generates any random states of CPT in certain probability to trend to the initial state or target state mapped with the end hosepipe path,and to have the least cost between this random state and its parent state. A typical case and two special cases are analyzed in which the end hosepipe paths are reciprocating linear trajectory and planar or spatial sine curves respectively. Their results verify the feasibility and validity of the proposed algorithm.

Elasto-plastic Analysis of High-strength Concrete Shear Wall with Boundary Columns Using Fiber Model

In this study,an experimental study and numerical calculations using fiber model were conducted for four high-strength concrete shear walls with boundary columns under low cyclic load.The boundary column and shear wall were divided into fiber elements,and PERFORM-3D finite element analysis software was used to carry out push-over analysis on the test specimens.The results show that the finite element analysis results were in good agreement with the experimental results.The proposed analysis method could perform elasto-plastic analysis on the high-strength concrete shear wall with boundary columns without distinguishing the categories of frame column and shear wall.The seismic performance of high-strength concrete shear wall with boundary columns was analyzed using the following parameters:axis compression ratio,height to width ratio,ratio of vertical reinforcement,and ratio of longitudinal reinforcement in the boundary column.The results show that the increase in the axial compression ratio causes the bearing capacity of the shear wall to increase at first and then to decrease and causes the ductility to decrease.The increase in the height to width ratio causes the bearing capacity of the shear wall to decrease and its ductility to increase.The ratio of vertical reinforcement was found to have little effect on the bearing capacity and ductility.The increase in the ratio of longitudinal reinforcement in boundary column resulted in a significant increase in the bearing capacity and caused the ductility to decrease at first and then to slowly increase.

Detection of Thermophysical Properties for High Strength Concrete after Exposure to High Temperature

Using the detection principle of infrared thermal imaging technique and the detection principle of DRH thermal conductivity tester laboratory,we investigated the infrared thermal image inspection,coefficient of thermal conductivity,apparent density,and compressive strength test on C80 high-strength concrete（HSC） in the presence and absence of polypropylene fibers under completely heated conditions.Only slight damages were detected below 400 ℃,whereas more and more severe deterioration events were expected when the temperature was above 500 ℃.The results show that the elevated temperature through infrared images generally exhibits an upward trend with increasing temperature,while the coefficient of thermal conductivity and apparent density decrease gradually.Additionally,the addition of polypropylene fibers with appropriate length,diameter,and quantity contributes to the improvement of the high-temperature resistance of HSC.

A Numerical Stress-strain Response Model of All Grades of Concretes under Uniaxial Compression

An important problem facing stress-strain response modeling of concrete is the complexity of the compressive strength grades. 21 groups of speeimens with different cubic compressive strength （56.3- 164.9 MPa ） hate beets numerically analyzed. Using only the compressive strength, a stress-strain response model of different concrete grade was established. The numerical simulation model not only qualitatively reproduces the relationship of uniaxial compressive strength, peak value stress and cubic compressive strength, but realizes the consistence of the ascending branch of stress-strain cunts with different strength grades by introducing the correction coefficient k. The results indicate k increases gradually from 0 to approximate 1 with the increase of the compressive strength, corresponding to the transition from the paracurve to straight line branch in stress-strain curves. When k is 0, the madel is identical to the Hognestad equation. A good agreement with the experiment data was obtained.

Formulating for Innovative Self-Compacting Concrete with Low Energy Super-Sulfated Cement Used for Sustainability Development

This study proposed a new way to formulate a low energy super-sulfated cement (SSC) which can be used to produce self-compacting concrete (SCC) with high compressive strength and durability in terms of chloride penetration resistance. This innovative SSC, different from the traditional SSC, was purely produced with a ternary mixture of three industrial by-products of ground granulated blast furnace slag, low calcium Class F fly ash and circulating fluidized bed combustion (CFBC) fly ash and was denoted as SFC-SSC (super-sulfated cement made by mixture of slag, Class F fly ash and CFBC fly ash). Experimental results showed that the combination of a fixed amount of 15 wt.% of CFBC fly ash with various ratios of Class F fly ash to slag could be used to produce the hardened SCCs with high 28-day compressive strengths (41.8 - 65.6 MPa). Addition of Class F fly ash led to the resulting SCCs with lowered price and preferable engineering properties, and thus it was considered as state-of-the-art method to drive such type of concrete towards sustainable construction materials.

日本桥梁施工工艺技术

针对桥梁结构特点和现场施工条件,日本桥梁技术人员在桥梁施工工艺技术方面做了一些有益的尝试。鹫见桥Ⅱ期工程最高墩高125 m,采用预先在工厂制作部分预制构件的方法,加快了施工进度;Ⅱ期、Ⅰ期工程桥梁间距仅50 cm,为避免Ⅱ期工程施工对Ⅰ期工程运营造成影响,采用了智能预警监控系统。日见梦大桥桥塔端斜拉索采用钢锚箱锚固,塔柱混凝土浇筑采用透明模板监控混凝土浇筑质量。杨梅山高架桥支点梁段采用分层浇筑以及钢筋部品化预制安装等施工工艺,缩短了工期。思惟花笑大桥为主跨150 m的连续刚构桥,最高墩高93 m,箱梁腹板与底板相交处钢筋密集,为确保混凝土填充密实,采用混凝土填充模拟系统确定最佳浇筑方法;该桥跨度大、墩身高,混凝土泵送距离长,通过多项混凝土工艺试验,提高了长距离泵送悬臂浇筑施工质量;采用新研发的三眼照相机对钢筋绑扎质量进行检测,实现了钢筋检测作业自动化。

低温季节泵送混凝土结构施工期温控防裂研究

低温季节施工时针对泵闸等结构泵送混凝土防冻与防裂的技术难题,以SYG工程为例,结合工程实际施工过程及现场温控监测成果进行大体积泵送混凝土温控防裂反馈分析;对比分析了不通水工况与实际通水工况下的应力曲线与混凝土容许拉应力曲线,并结合现场温控过程中存在的主要问题探讨了低温季节下泵闸工程的温控防裂技术.结果表明,在-8℃的较低温度下,采取充分的水管冷却和严格的表面保温措施可有效控制结构内部最高温度、内外温差以及最大拉应力水平,减小水闸结构开裂风险.本工程温控实践经验可为类似条件下的泵闸工程提供参考.

泵送碱式硫酸镁水泥混凝土的制备和性能

碱式硫酸镁水泥混凝土是新开发出来不久的混凝土材料,具有高抗拉强度、抗冲击和耐腐蚀等优点,但由于其较小的塌落度,限制了其工程应用。本文试验研究了不同掺量萘系减水剂对泵送碱式硫酸镁水泥混凝土塌落度和强度的影响,确定强度等级C30、C40、C50和C60的萘系高效减水剂适宜掺量分别为2.0%、1.2%、1.5%和1.8%。分别研究了掺粉煤灰型和矿渣型泵送碱式硫酸镁水泥混凝土基本力学性能及在海水浸泡、淡水浸泡1280 d后的强度保留率并进行机理分析,发现粉煤灰型泵送碱式硫酸镁水泥混凝土抗海水腐蚀性较好,适合东部沿海地区应用;随着海水暴露时间的延长,泵送碱式硫酸镁水泥混凝土的Df值呈现幂函数的降低关系。本文还对大气中暴露2400 d的钢筋泵送碱式硫酸镁水泥混凝土小梁进行观测,未有锈涨现象。本文为碱式硫酸镁水泥混凝土在工程领域的应用具有重大意义。