Electronic devices have become ubiquitous in our daily lives,leading to a surge in the use of microwave absorbers and wearable sensor devices across various sectors.A prime example of this trend is the aramid nanofibe...Electronic devices have become ubiquitous in our daily lives,leading to a surge in the use of microwave absorbers and wearable sensor devices across various sectors.A prime example of this trend is the aramid nanofibers/polypyrrole/nickel(APN)aerogels,which serve dual roles as both microwave absorbers and pressure sensors.In this work,we focused on the preparation of aramid nanofibers/polypyrrole(AP15)aerogels,where the mass ratio of aramid nanofibers to pyrrole was 1:5.We employed the oxidative polymerization method for the preparation process.Following this,nickel was thermally evaporated onto the surface of the AP15 aerogels,resulting in the creation of an ultralight(9.35 mg·cm^(-3)).This aerogel exhibited a porous structure.The introduction of nickel into the aerogel aimed to enhance magnetic loss and adjust impedance matching,thereby improving electromagnetic wave absorption performance.The minimum reflection loss value achieved was-48.7 dB,and the maximum effective absorption bandwidth spanned 8.42 GHz with a thickness of 2.9 mm.These impressive metrics can be attributed to the three-dimensional network porous structure of the aerogel and perfect impedance matching.Moreover,the use of aramid nanofibers and a three-dimensional hole structure endowed the APN aerogels with good insulation,flame-retardant properties,and compression resilience.Even under a compression strain of 50%,the aerogel maintained its resilience over 500 cycles.The incorporation of polypyrrole and nickel particles further enhanced the conductivity of the aerogel.Consequently,the final APN aerogel sensor demonstrated high sensitivity(10.78 kPa-1)and thermal stability.In conclusion,the APN aerogels hold significant promise as ultra-broadband microwave absorbers and pressure sensors.展开更多
Flexible pressure sensors have many potential applications in the monitoring of physiological signals because of their good biocompatibil-ity and wearability.However,their relatively low sensitivity,linearity,and stab...Flexible pressure sensors have many potential applications in the monitoring of physiological signals because of their good biocompatibil-ity and wearability.However,their relatively low sensitivity,linearity,and stability have hindered their large-scale commercial application.Herein,aflexible capacitive pressure sensor based on an interdigital electrode structure with two porous microneedle arrays(MNAs)is pro-posed.The porous substrate that constitutes the MNA is a mixed product of polydimethylsiloxane and NaHCO3.Due to its porous and interdigital structure,the maximum sensitivity(0.07 kPa-1)of a porous MNA-based pressure sensor was found to be seven times higher than that of an imporous MNA pressure sensor,and it was much greater than that of aflat pressure sensor without a porous MNA structure.Finite-element analysis showed that the interdigital MNA structure can greatly increase the strain and improve the sensitivity of the sen-sor.In addition,the porous MNA-based pressure sensor was found to have good stability over 1500 loading cycles as a result of its bilayer parylene-enhanced conductive electrode structure.Most importantly,it was found that the sensor could accurately monitor the motion of afinger,wrist joint,arm,face,abdomen,eye,and Adam’s apple.Furthermore,preliminary semantic recognition was achieved by monitoring the movement of the Adam’s apple.Finally,multiple pressure sensors were integrated into a 33 array to detect a spatial pressure distribu-×tion.Compared to the sensors reported in previous works,the interdigital electrode structure presented in this work improves sensitivity and stability by modifying the electrode layer rather than the dielectric layer.展开更多
In this paper, a novel antenna is proposed for high-temperature testing, which can make the high-temperature pressure characteristics of a wireless passive ceramic pressure sensor demonstrated at up to a temperature o...In this paper, a novel antenna is proposed for high-temperature testing, which can make the high-temperature pressure characteristics of a wireless passive ceramic pressure sensor demonstrated at up to a temperature of 600℃. The design parameters of the antenna are similar to those of the sensor, which will increase the coupling strength between the sensor and testing antenna. The antenna is fabricated in thick film integrated technology, and the properties of the alumina ceramic and silver ensure the feasibility of the antenna in high-temperature environments. The sensor, coupled with the ceramic antenna, is investigated using a high-temperature pressure testing platform. The experimental measurement results show that the pressure signal in a harsh environment can be detected by the frequency diversity of the sensor.展开更多
Multifunctional architecture with intriguing structural design is highly desired for realizing the promising performances in wearable sensors and flexible energy storage devices.Cellulose nanofiber(CNF)is employed for...Multifunctional architecture with intriguing structural design is highly desired for realizing the promising performances in wearable sensors and flexible energy storage devices.Cellulose nanofiber(CNF)is employed for assisting in building conductive,hyperelastic,and ultralight Ti_(3)C_(2)T_(x)MXene hybrid aerogels with oriented tracheid-like texture.The biomimetic hybrid aerogels are constructed by a facile bidirectional freezing strategy with CNF,carbon nanotube(CNT),and MXene based on synergistic electrostatic interaction and hydrogen bonding.Entangled CNF and CNT“mortars”bonded with MXene“bricks”of the tracheid structure produce good interfacial binding,and superior mechanical strength(up to 80%compressibility and extraordinary fatigue resistance of 1000 cycles at 50%strain).Benefiting from the biomimetic texture,CNF/CNT/MXene aerogel shows ultralow density of 7.48 mg cm^(-3)and excellent electrical conductivity(~2400 S m^(-1)).Used as pressure sensors,such aerogels exhibit appealing sensitivity performance with the linear sensitivity up to 817.3 kPa^(-1),which affords their application in monitoring body surface information and detecting human motion.Furthermore,the aerogels can also act as electrode materials of compressive solid-state supercapacitors that reveal satisfactory electrochemical performance(849.2 mF cm^(-2)at 0.8 mA cm^(-2))and superior long cycle compression performance(88%after 10,000 cycles at a compressive strain of 30%).展开更多
Flexible,breathable,and highly sensitive pressure sensors have increasingly become a focal point of interest due to their pivotal role in healthcare monitoring,advanced electronic skin applications,and disease diagnos...Flexible,breathable,and highly sensitive pressure sensors have increasingly become a focal point of interest due to their pivotal role in healthcare monitoring,advanced electronic skin applications,and disease diagnosis.However,traditional methods,involving elastomer film-based substrates or encapsulation techniques,often fall short due to mechanical mismatches,discomfort,lack of breathability,and limitations in sensing abilities.Consequently,there is a pressing need,yet it remains a significant challenge to create pressure sensors that are not only highly breathable,flexible,and comfortable but also sensitive,durable,and biocompatible.Herein,we present a biocompatible and breathable fabric-based pressure sensor,using nonwoven fabrics as both the sensing electrode(coated with MXene/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate[PEDOT:PSS])and the interdigitated electrode(printed with MXene pattern)via a scalable spray-coating and screen-coating technique.The resultant device exhibits commendable air permeability,biocompatibility,and pressure sensing performance,including a remarkable sensitivity(754.5 kPa^(−1)),rapid response/recovery time(180/110 ms),and robust cycling stability.Furthermore,the integration of PEDOT:PSS plays a crucial role in protecting the MXene nanosheets from oxidation,significantly enhancing the device's long-term durability.These outstanding features make this sensor highly suitable for applications in fullrange human activities detection and disease diagnosis.Our study underscores the promising future of flexible pressure sensors in the realm of intelligent wearable electronics,setting a new benchmark for the industry.展开更多
The principle of miniature isolated solid-state encapsulation technology of high-temperature pressure sensor and the structure of packaging are discussed, including static electricity bonding, stainless steel diaphrag...The principle of miniature isolated solid-state encapsulation technology of high-temperature pressure sensor and the structure of packaging are discussed, including static electricity bonding, stainless steel diaphragm selection and rippled design, laser welding, silicon oil infilling, isolation and other techniques used in sensor packaging, which can affect the performance of the sensor. By adopting stainless steel diaphragm and high-temperature silicon oil as isolation materials, not only the encapsulation of the sensor is as small as 15 mm in diameter and under 1 mA drive, its full range output is 72 mV and zero stability is 0.48% F.S/mon, but also the reliability of the sensor is improved and its application is widely broadened.展开更多
The human skin has the ability to sense tactile touch and a great range of pressures.Therefore,in prosthetic or robotic systems,it is necessary to prepare pressure sensors with high sensitivity in a wide measurement r...The human skin has the ability to sense tactile touch and a great range of pressures.Therefore,in prosthetic or robotic systems,it is necessary to prepare pressure sensors with high sensitivity in a wide measurement range to provide human-like tactile sensation.Herein,we developed a flexible piezoresistive pressure sensor that is highly sensitive in a broad pressure range by using lotus leaf micropatterned polydimethylsiloxane and multilayer superposition.By superposing four layers of micropatterned constructive substrates,the multilayer piezoresistive pressure sensor achieves a broad pressure range of 312 kPa,a high sensitivity of 2.525 kPa^(−1),a low limit of detection(LOD)of<12 Pa,and a fast response time of 45 ms.Compared with the traditional flexible pressure sensor,the pressure range of this sensor can be increased by at least an order of magnitude.The flexible piezoresistive pressure sensor also shows high robustness:after testing for at least 1000 cycles,it shows no sign of fatigue.More importantly,these sensors can be potentially applied in various human motion detection scenarios,including tiny pulse monitoring,throat vibration detection,and large under-feet pressure sensing.The proposed fabrication strategy may guide the design of other kinds of multifunctional sensors to improve the detection performance.展开更多
The flexible pressure sensor has been credited for leading performance including higher sensitivity,faster response/recovery,wider detection range and higher mechanical durability,thus driving the development of novel...The flexible pressure sensor has been credited for leading performance including higher sensitivity,faster response/recovery,wider detection range and higher mechanical durability,thus driving the development of novel sensing materials enabled by new processing technologies.Using atomic layer infiltration,Pt nanocrystals with dimensions on the order of a few nanometers can be infiltrated into the compressible lamellar structure of Ti3C2Tx MXene,allowing a modulation of its interlayer spacing,electrical conductivity and piezoresistive property.The flexible piezoresistive sensor is further developed from the Pt-infiltrated MXene on a paper substrate.It is demonstrated that Pt infiltration leads to a significant enhancement of the pressure-sensing performance of the sensor,including increase of sensitivity from 0.08 kPa^(-1)to 0.5 kPa^(-1),extension of detection limit from 5 kPa to 9 kPa,decrease of response time from 200 ms to 20 ms,and reduction of recovery time from 230 ms to 50 ms.The mechanical durability of the flexible sensor is also improved,with the piezoresistive performance stable over 1000 cycles of flexure fatigue.The atomic layer infiltration process offers new possibilities for the structure modification of MXene for advanced sensor applications.展开更多
Ionic gels can be potentially used in wearable devices owing to their high humidity resistance and non-volatility.However,the applicability of existing ionic gel pressure sensors is limited by their low sensitivity.Th...Ionic gels can be potentially used in wearable devices owing to their high humidity resistance and non-volatility.However,the applicability of existing ionic gel pressure sensors is limited by their low sensitivity.Therefore,it is very import-ant to develop an ionic gel pressure sensor with high sensitivity and a wide pressure detection range without sacrificing mechan-ical stretchability and self-healing ability.Herein,we report an effective strategy for developing pressure sensors based on ion-ic gel composites consisting of high-molecular-weight polymers,ionic liquids,and Au nanoparticles.The resulting capacitive pressure sensors exhibit high pressure sensitivity,fast response,and excellent self-healing properties.The sensors composed of highly hydrophobic polymers and ionic liquids can be used to track underwater movements,demonstrating broad application prospects in human motion state monitoring and underwater mechanical operations.展开更多
Transparent electrode based on silver nanowires(Ag NWs) emerges as an outstanding alternative of indium tin oxide film especially for flexible electronics. However, the conductivity of Ag NWs transparent electrode is ...Transparent electrode based on silver nanowires(Ag NWs) emerges as an outstanding alternative of indium tin oxide film especially for flexible electronics. However, the conductivity of Ag NWs transparent electrode is still dramatically limited by the contact resistance between nanowires at high transmittance. Polyvinylpyrrolidone(PVP) layer adsorbed on the nanowire surface acts as an electrically insulating barrier at wire–wire junctions, and some devastating post-treatment methods are proposed to reduce or eliminate PVP layer, which usually limit the application of the substrates susceptible to heat or pressure and burden the fabrication with high-cost, time-consuming, or inefficient processes. In this work, a simple and rapid pre-treatment washing method was proposed to reduce the thickness of PVP layer from 13.19 to0.96 nm and improve the contact between wires. Ag NW electrodes with sheet resistances of 15.6 and 204 X sq-1have been achieved at transmittances of 90 and 97.5 %, respectively. This method avoided any post-treatments and popularized the application of high-performance Ag NW transparent electrode on more substrates. The improved Ag NWs were successfully employed in a capacitive pressure sensor with high transparency, sensitivity, and reproducibility.展开更多
In recent years, advanced composite structures are used extensively in many industries such as aerospace, aircraft, automobile, pipeline and civil engineering. Reliability and safety are crucial requirements posed by ...In recent years, advanced composite structures are used extensively in many industries such as aerospace, aircraft, automobile, pipeline and civil engineering. Reliability and safety are crucial requirements posed by them to the advanced composite structures be- cause of their harsh working conditions. Therefore, as a very important measure, structural health monitoring (SHM) in-service is deft- nitely demanded for ensuring their safe working in-situ. In this paper, fiber Bragg grating (FBG) sensors are surface-mounted on the hoop and in the axial directions of a FRP pressure vessel to monitor the strain status during its pressurization. The experimental results show that the FBG sensors could be used to monitor the strain development and determine the ultimate failure strain of the composite pressure vessel.展开更多
Small-sized,low-cost,and high-sensitivity sensors are required for pressure-sensing applications because of their critical role in consumer electronics,automotive applications,and industrial environments.Thus,micro/na...Small-sized,low-cost,and high-sensitivity sensors are required for pressure-sensing applications because of their critical role in consumer electronics,automotive applications,and industrial environments.Thus,micro/nanoscale pressure sensors based on micro/nanofabrication and micro/nanoelectromechanical system technologies have emerged as a promising class of pressure sensors on account of their remarkable miniaturization and performance.These sensors have recently been developed to feature multifunctionality and applicability to novel scenarios,such as smart wearable devices and health monitoring systems.In this review,we summarize the major sensing principles used in micro/nanoscale pressure sensors and discuss recent progress in the development of four major categories of these sensors,namely,novel material-based,flexible,implantable,and selfpowered pressure sensors.展开更多
As an indispensable branch of wearable electronics,flexible pressure sensors are gaining tremendous attention due to their extensive applications in health monitoring,human-machine interaction,artificial intelligence,...As an indispensable branch of wearable electronics,flexible pressure sensors are gaining tremendous attention due to their extensive applications in health monitoring,human-machine interaction,artificial intelligence,the internet of things,and other fields.In recent years,highly flexible and wearable pressure sensors have been developed using various materials/structures and transduction mechanisms.Morphological engineering of sensing materials at the nanometer and micrometer scales is crucial to obtaining superior sensor performance.This review focuses on the rapid development of morphological engineering technologies for flexible pressure sensors.We discuss different architectures and morphological designs of sensing materials to achieve high performance,including high sensitivity,broad working range,stable sensing,low hysteresis,high transparency,and directional or selective sensing.Additionally,the general fabrication techniques are summarized,including self-assembly,patterning,and auxiliary synthesis methods.Furthermore,we present the emerging applications of high-performing microengineered pressure sensors in healthcare,smart homes,digital sports,security monitoring,and machine learning-enabled computational sensing platform.Finally,the potential challenges and prospects for the future developments of pressure sensors are discussed comprehensively.展开更多
This paper reports the current-voltage characteristics of [001]-oriented AlAs/InxGa1-xAs/GaAs resonant tunnelling diodes (RTDs) as a function of uniaxial external stress applied parallel to the [110] and the [1^-10]...This paper reports the current-voltage characteristics of [001]-oriented AlAs/InxGa1-xAs/GaAs resonant tunnelling diodes (RTDs) as a function of uniaxial external stress applied parallel to the [110] and the [1^-10] orientations, and the output characteristics of the GaAs pressure sensor based on the pressure effect on the RTDs. Under [110] stress, the resonance peak voltages of the RTDs shift to more positive voltages. For [1^-10] stress, the peaks shift toward more negative voltages. The resonance peak voltage is linearly dependent on the [110] and [1^-0] stresses and the linear sensitivities are up to 0.69 mV/MPa, -0.69 mV/MPa respectively. For the pressure sensor, the linear sensitivity is up to 0.37 mV/kPa.展开更多
Environmentally friendly degradable sensors with both hazardous gases and pressure efficient sensing capabilities are highly desired for various promising applications,including environmental pollution monitoring/prev...Environmentally friendly degradable sensors with both hazardous gases and pressure efficient sensing capabilities are highly desired for various promising applications,including environmental pollution monitoring/prevention,wisdom medical,wearable smart devices,and artificial intelligence.However,the transient gas and pressure sensors based on only identical sensing material that concurrently meets the above detection needs have not been reported.Here,we present transient all-MXene NO_(2) and pressure sensors employing three-dimensional porous crumpled MXene spheres prepared by ultrasonic spray pyrolysis technology as the sensing layer,accompanied with water-soluble polyvinyl alcohol substrates embedded with patterned MXene electrodes.The gas sensor achieves a ppb-level of highly selective NO_(2) sensing,with a response of up to 12.11%at 5 ppm NO_(2) and a detection range of 50 ppb-5 ppm,while the pressure sensor has an extremely wide linear pressure detection range of 0.14-22.22 kPa and fast response time of 34 ms.In parallel,all-MXene NO_(2) and pressure sensors can be rapidly degraded in medical H_(2)O_(2) within 6 h.This work provides a new avenue toward environmental monitoring,human physiological signal monitoring,and recyclable transient electronics.展开更多
In this paper, we present the design, the fabrication, and the experimental results of carbon nanotube (CNT) and Cu20 composite based pressure sensors. The pressed tablets of the CNT Cu20 composite are fabricated at...In this paper, we present the design, the fabrication, and the experimental results of carbon nanotube (CNT) and Cu20 composite based pressure sensors. The pressed tablets of the CNT Cu20 composite are fabricated at a pressure of 353 MPa. The diameters of the multiwalled nanotubes (MWNTs) are between 10 nm and 30 nm. The sizes of the Cu20 micro particles are in the range of 3-4 μm. The average diameter and the average thickness of the pressed tablets are 10 mm and 4.0 mm, respectively. In order to make low resistance electric contacts, the two sides of the pressed tablet are covered by silver pastes. The direct current resistance of the pressure sensor decreases by 3.3 times as the pressure increases up to 37 kN/m^2. The simulation result of the resistance-pressure relationship is in good agreement with the experimental result within a variation of ±2%.展开更多
Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure(HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques(PPTs). To improve...Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure(HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques(PPTs). To improve the accuracy of geopressure prediction in HTHP hydrocarbon reservoirs offshore Hainan Island, we made a comprehensive summary of current PPTs to identify existing problems and challenges by analyzing the global distribution of HTHP hydrocarbon reservoirs, the research status of PPTs, and the geologic setting and its HTHP formation mechanism. Our research results indicate that the HTHP formation mechanism in the study area is caused by multiple factors, including rapid loading, diapir intrusions, hydrocarbon generation, and the thermal expansion of pore fluids. Due to this multi-factor interaction, a cloud of HTHP hydrocarbon reservoirs has developed in the Ying-Qiong Basin, but only traditional PPTs have been implemented, based on the assumption of conditions that do not conform to the actual geologic environment, e.g., Bellotti's law and Eaton's law. In this paper, we focus on these issues, identify some challenges and solutions, and call for further PPT research to address the drawbacks of previous works and meet the challenges associated with the deepwater technology gap. In this way, we hope to contribute to the improved accuracy of geopressure prediction prior to drilling and provide support for future HTHP drilling offshore Hainan Island.展开更多
Yinggehai Basin locates in the northern South China Sea. Since the Cainozoic Era, crust has several strong tension: the basin subsides quickly, the deposition is thick, and the crust is thin. In the central basin, for...Yinggehai Basin locates in the northern South China Sea. Since the Cainozoic Era, crust has several strong tension: the basin subsides quickly, the deposition is thick, and the crust is thin. In the central basin, formation pressure coefficient is up to 2.1;Yinggehai Basin is a fomous high-temperature overpressure basin.YinggehaiBasin’s in-depth, especially high-temperature overpressure stratum has numerous large-scale exploration goals. As a result of high-temperature overpressure basin’s perplexing geological conditions and geophysical analysis technical limitations, this field of gas exploration can’t be carried out effectively, which affects the process of gas exploration seriously. A pressure prediction model of the high-temperature overpressure basin in different structural positions is summed up by pressure forecast pattern research in recent years, which can be applied to target wells pre-drilling pressure prediction and post drilling pressure analysis of Yinggehai Basin. The model has small erroneous and high rate of accuracy. The Yinggehai Basin A well drilling is successful in 2010, and gas is discovered in high-temperature overpressure stratum, which proved that reservoir can be found in high-temperature overpressure stratum. It is a great theoretical breakthrough of reservoir knowledge.展开更多
Aiming at piezoresistive pressure sensors, this paper studies simulation of standard pressure by using benchmark current source and self-calibration of the sampling data characteristics. A data fusion algorithm for sa...Aiming at piezoresistive pressure sensors, this paper studies simulation of standard pressure by using benchmark current source and self-calibration of the sampling data characteristics. A data fusion algorithm for sample set is presented which transforms a surface problem into a curve fitting and interpolation problem. The simulation result shows that benchmark current source simulating pressure is successful and data fusion algorithm is effective. The maximum measurement error is only 0.098 kPa and maximum relative error is 0.92% at 0-45 kPa and -10-45~C.展开更多
Flexible piezoresistive pressure sensors can offer convenient detection of mechanical deformations for wearable electronics.Previous studies of flexible piezoresistive pressure sensors focus on the sensitivity but the...Flexible piezoresistive pressure sensors can offer convenient detection of mechanical deformations for wearable electronics.Previous studies of flexible piezoresistive pressure sensors focus on the sensitivity but the low-cost and self-powered sensors remain a challenge due to the deviation of resistance signal acquisition caused by thermoelectric voltage.Here,piezoresistive pressure sensors with ultralow Seebeck coefficient of-0.72μV/K based on carbon nanotubes(CNTs)/polyethyleneimine(PEI)/melamine(CPM)sponge are reported.Due to the diminished Seebeck effect,the CPM sponge pressure sensors successfully reduce the deviation to 18.75%and can keep stable sensitivity and resistance change under a very low working voltage and change temperature environment.The stable properties of the sensors make them successful to work for real-time sensing in self-powered wearable electronics.展开更多
基金The authors acknowledge the financial support from the National Natural Science Foundation of China(Nos.52071280 and 51972280)the Natural Science Foundation of Hebei Province,China(Nos.E2020203151 and E2022203208)+1 种基金the Research Program of the College Science&Technology of Hebei Province,China(No.ZD2020121)the Cultivation Project for Basic Research and Innovation of Yanshan University,China(No.2021LGZD016).
文摘Electronic devices have become ubiquitous in our daily lives,leading to a surge in the use of microwave absorbers and wearable sensor devices across various sectors.A prime example of this trend is the aramid nanofibers/polypyrrole/nickel(APN)aerogels,which serve dual roles as both microwave absorbers and pressure sensors.In this work,we focused on the preparation of aramid nanofibers/polypyrrole(AP15)aerogels,where the mass ratio of aramid nanofibers to pyrrole was 1:5.We employed the oxidative polymerization method for the preparation process.Following this,nickel was thermally evaporated onto the surface of the AP15 aerogels,resulting in the creation of an ultralight(9.35 mg·cm^(-3)).This aerogel exhibited a porous structure.The introduction of nickel into the aerogel aimed to enhance magnetic loss and adjust impedance matching,thereby improving electromagnetic wave absorption performance.The minimum reflection loss value achieved was-48.7 dB,and the maximum effective absorption bandwidth spanned 8.42 GHz with a thickness of 2.9 mm.These impressive metrics can be attributed to the three-dimensional network porous structure of the aerogel and perfect impedance matching.Moreover,the use of aramid nanofibers and a three-dimensional hole structure endowed the APN aerogels with good insulation,flame-retardant properties,and compression resilience.Even under a compression strain of 50%,the aerogel maintained its resilience over 500 cycles.The incorporation of polypyrrole and nickel particles further enhanced the conductivity of the aerogel.Consequently,the final APN aerogel sensor demonstrated high sensitivity(10.78 kPa-1)and thermal stability.In conclusion,the APN aerogels hold significant promise as ultra-broadband microwave absorbers and pressure sensors.
基金supported in part by the National Natural Science Foundation of China(Grant No.62104056)the Zhejiang Provincial Natural Science Foundation of China(Grant No.LQ21F010010)+4 种基金the National Natural Science Foundation of China(Grant Nos.62141409 and 62204204)the National Key R&D Program of China(Grant No.2022ZD0208602)the Zhejiang Provincial Key Research&Development Fund(Grant Nos.2019C04003 and 2021C01041)the Shanghai Sailing Program(Grant No.21YF1451000)the Key Research and Development Program of Shaanxi(Grant No.2022GY-001).
文摘Flexible pressure sensors have many potential applications in the monitoring of physiological signals because of their good biocompatibil-ity and wearability.However,their relatively low sensitivity,linearity,and stability have hindered their large-scale commercial application.Herein,aflexible capacitive pressure sensor based on an interdigital electrode structure with two porous microneedle arrays(MNAs)is pro-posed.The porous substrate that constitutes the MNA is a mixed product of polydimethylsiloxane and NaHCO3.Due to its porous and interdigital structure,the maximum sensitivity(0.07 kPa-1)of a porous MNA-based pressure sensor was found to be seven times higher than that of an imporous MNA pressure sensor,and it was much greater than that of aflat pressure sensor without a porous MNA structure.Finite-element analysis showed that the interdigital MNA structure can greatly increase the strain and improve the sensitivity of the sen-sor.In addition,the porous MNA-based pressure sensor was found to have good stability over 1500 loading cycles as a result of its bilayer parylene-enhanced conductive electrode structure.Most importantly,it was found that the sensor could accurately monitor the motion of afinger,wrist joint,arm,face,abdomen,eye,and Adam’s apple.Furthermore,preliminary semantic recognition was achieved by monitoring the movement of the Adam’s apple.Finally,multiple pressure sensors were integrated into a 33 array to detect a spatial pressure distribu-×tion.Compared to the sensors reported in previous works,the interdigital electrode structure presented in this work improves sensitivity and stability by modifying the electrode layer rather than the dielectric layer.
基金Project supported by the National Natural Science Foundation for Distinguished Young Scholars,China(Grant No.51425505)the National Natural Science Foundation of China(Grant No.61471324)+1 种基金the Program for the Outstanding Innovative Teams of Higher Learning Institutions of Shanxi Province,China(Grant No.2013-077)the Graduate Students Outstanding Innovation Project of Shanxi Province,China(Grant No.20143020)
文摘In this paper, a novel antenna is proposed for high-temperature testing, which can make the high-temperature pressure characteristics of a wireless passive ceramic pressure sensor demonstrated at up to a temperature of 600℃. The design parameters of the antenna are similar to those of the sensor, which will increase the coupling strength between the sensor and testing antenna. The antenna is fabricated in thick film integrated technology, and the properties of the alumina ceramic and silver ensure the feasibility of the antenna in high-temperature environments. The sensor, coupled with the ceramic antenna, is investigated using a high-temperature pressure testing platform. The experimental measurement results show that the pressure signal in a harsh environment can be detected by the frequency diversity of the sensor.
基金supported by the Project of Jinan City(202228044)National Natural Science Foundation of China(32071720,32271814)+1 种基金the China Postdoctoral Science Foundation(2021M702456)China Scholarship Council for supporting their PhD program。
文摘Multifunctional architecture with intriguing structural design is highly desired for realizing the promising performances in wearable sensors and flexible energy storage devices.Cellulose nanofiber(CNF)is employed for assisting in building conductive,hyperelastic,and ultralight Ti_(3)C_(2)T_(x)MXene hybrid aerogels with oriented tracheid-like texture.The biomimetic hybrid aerogels are constructed by a facile bidirectional freezing strategy with CNF,carbon nanotube(CNT),and MXene based on synergistic electrostatic interaction and hydrogen bonding.Entangled CNF and CNT“mortars”bonded with MXene“bricks”of the tracheid structure produce good interfacial binding,and superior mechanical strength(up to 80%compressibility and extraordinary fatigue resistance of 1000 cycles at 50%strain).Benefiting from the biomimetic texture,CNF/CNT/MXene aerogel shows ultralow density of 7.48 mg cm^(-3)and excellent electrical conductivity(~2400 S m^(-1)).Used as pressure sensors,such aerogels exhibit appealing sensitivity performance with the linear sensitivity up to 817.3 kPa^(-1),which affords their application in monitoring body surface information and detecting human motion.Furthermore,the aerogels can also act as electrode materials of compressive solid-state supercapacitors that reveal satisfactory electrochemical performance(849.2 mF cm^(-2)at 0.8 mA cm^(-2))and superior long cycle compression performance(88%after 10,000 cycles at a compressive strain of 30%).
基金supported by the National Natural Science Foundation of China(52303051,52202108,52003002)Anhui Provincial Natural Science Foundation(2308085ME146,2008085QE213)+3 种基金Educational Commission of Anhui Province of China(2022AH040137)Key Laboratory of Intelligent Textile and Flexible Interconnection of Zhejiang Province(ZD04)Opening Fund of China National Textile and Apparel Council Key Laboratory of Flexible Devices for Intelligent Textile and Apparel,Soochow University(SDHY2227)research funding from Anhui Polytechnic University(2020YQQ002,Xjky2022070,FFBK202218,FFBK202363,FFBK202364,2020ffky01).
文摘Flexible,breathable,and highly sensitive pressure sensors have increasingly become a focal point of interest due to their pivotal role in healthcare monitoring,advanced electronic skin applications,and disease diagnosis.However,traditional methods,involving elastomer film-based substrates or encapsulation techniques,often fall short due to mechanical mismatches,discomfort,lack of breathability,and limitations in sensing abilities.Consequently,there is a pressing need,yet it remains a significant challenge to create pressure sensors that are not only highly breathable,flexible,and comfortable but also sensitive,durable,and biocompatible.Herein,we present a biocompatible and breathable fabric-based pressure sensor,using nonwoven fabrics as both the sensing electrode(coated with MXene/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate[PEDOT:PSS])and the interdigitated electrode(printed with MXene pattern)via a scalable spray-coating and screen-coating technique.The resultant device exhibits commendable air permeability,biocompatibility,and pressure sensing performance,including a remarkable sensitivity(754.5 kPa^(−1)),rapid response/recovery time(180/110 ms),and robust cycling stability.Furthermore,the integration of PEDOT:PSS plays a crucial role in protecting the MXene nanosheets from oxidation,significantly enhancing the device's long-term durability.These outstanding features make this sensor highly suitable for applications in fullrange human activities detection and disease diagnosis.Our study underscores the promising future of flexible pressure sensors in the realm of intelligent wearable electronics,setting a new benchmark for the industry.
文摘The principle of miniature isolated solid-state encapsulation technology of high-temperature pressure sensor and the structure of packaging are discussed, including static electricity bonding, stainless steel diaphragm selection and rippled design, laser welding, silicon oil infilling, isolation and other techniques used in sensor packaging, which can affect the performance of the sensor. By adopting stainless steel diaphragm and high-temperature silicon oil as isolation materials, not only the encapsulation of the sensor is as small as 15 mm in diameter and under 1 mA drive, its full range output is 72 mV and zero stability is 0.48% F.S/mon, but also the reliability of the sensor is improved and its application is widely broadened.
基金the Project of National Key Research and Development Program of China(No.2018YFC2001300)the National Natural Science Foundation of China(Nos.52175271,51822504,52021003,52105299,51905207,and 91948302)+2 种基金Science and Technology Development Plan Project of Jilin Province(No.20210508057RQ)Program for JinlinUniversity Science and Technology Innovative Research Team(No.2017TD-04)Scientific Research Project of EducationDepartment of Jilin Province(No.JJKH20211084KJ).
文摘The human skin has the ability to sense tactile touch and a great range of pressures.Therefore,in prosthetic or robotic systems,it is necessary to prepare pressure sensors with high sensitivity in a wide measurement range to provide human-like tactile sensation.Herein,we developed a flexible piezoresistive pressure sensor that is highly sensitive in a broad pressure range by using lotus leaf micropatterned polydimethylsiloxane and multilayer superposition.By superposing four layers of micropatterned constructive substrates,the multilayer piezoresistive pressure sensor achieves a broad pressure range of 312 kPa,a high sensitivity of 2.525 kPa^(−1),a low limit of detection(LOD)of<12 Pa,and a fast response time of 45 ms.Compared with the traditional flexible pressure sensor,the pressure range of this sensor can be increased by at least an order of magnitude.The flexible piezoresistive pressure sensor also shows high robustness:after testing for at least 1000 cycles,it shows no sign of fatigue.More importantly,these sensors can be potentially applied in various human motion detection scenarios,including tiny pulse monitoring,throat vibration detection,and large under-feet pressure sensing.The proposed fabrication strategy may guide the design of other kinds of multifunctional sensors to improve the detection performance.
基金supported by the National Natural Science Foundation of China(51835005,52273237,51871103)National Key Research and Development Program of China(2020YFB2010401)+1 种基金the Hubei Province Natural Science Foundation for innovative research groups(2020CFA030)Tencent Foundation and the Independent Innovation Research Fund of Huazhong University of Science and Technology(2019kfyXMBZ025).
文摘The flexible pressure sensor has been credited for leading performance including higher sensitivity,faster response/recovery,wider detection range and higher mechanical durability,thus driving the development of novel sensing materials enabled by new processing technologies.Using atomic layer infiltration,Pt nanocrystals with dimensions on the order of a few nanometers can be infiltrated into the compressible lamellar structure of Ti3C2Tx MXene,allowing a modulation of its interlayer spacing,electrical conductivity and piezoresistive property.The flexible piezoresistive sensor is further developed from the Pt-infiltrated MXene on a paper substrate.It is demonstrated that Pt infiltration leads to a significant enhancement of the pressure-sensing performance of the sensor,including increase of sensitivity from 0.08 kPa^(-1)to 0.5 kPa^(-1),extension of detection limit from 5 kPa to 9 kPa,decrease of response time from 200 ms to 20 ms,and reduction of recovery time from 230 ms to 50 ms.The mechanical durability of the flexible sensor is also improved,with the piezoresistive performance stable over 1000 cycles of flexure fatigue.The atomic layer infiltration process offers new possibilities for the structure modification of MXene for advanced sensor applications.
基金supported by the National Natural Science Foundation of China(NSFC,Grant Nos.61874111,62174152 and 62022079)the National Key Research and Development Program of China(Grant No.2020YFB1506400)+1 种基金the Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2020115)the Strategic Priority Research Program of the Chinese Academy of Sciences(XDA16021200).
文摘Ionic gels can be potentially used in wearable devices owing to their high humidity resistance and non-volatility.However,the applicability of existing ionic gel pressure sensors is limited by their low sensitivity.Therefore,it is very import-ant to develop an ionic gel pressure sensor with high sensitivity and a wide pressure detection range without sacrificing mechan-ical stretchability and self-healing ability.Herein,we report an effective strategy for developing pressure sensors based on ion-ic gel composites consisting of high-molecular-weight polymers,ionic liquids,and Au nanoparticles.The resulting capacitive pressure sensors exhibit high pressure sensitivity,fast response,and excellent self-healing properties.The sensors composed of highly hydrophobic polymers and ionic liquids can be used to track underwater movements,demonstrating broad application prospects in human motion state monitoring and underwater mechanical operations.
基金partly supported by Showa Denko Co. Ltd, Grant-in-Aid for Scientific Research (Kaken S, 24226017)COI Stream Projectfinancial support from China Scholarship Council
文摘Transparent electrode based on silver nanowires(Ag NWs) emerges as an outstanding alternative of indium tin oxide film especially for flexible electronics. However, the conductivity of Ag NWs transparent electrode is still dramatically limited by the contact resistance between nanowires at high transmittance. Polyvinylpyrrolidone(PVP) layer adsorbed on the nanowire surface acts as an electrically insulating barrier at wire–wire junctions, and some devastating post-treatment methods are proposed to reduce or eliminate PVP layer, which usually limit the application of the substrates susceptible to heat or pressure and burden the fabrication with high-cost, time-consuming, or inefficient processes. In this work, a simple and rapid pre-treatment washing method was proposed to reduce the thickness of PVP layer from 13.19 to0.96 nm and improve the contact between wires. Ag NW electrodes with sheet resistances of 15.6 and 204 X sq-1have been achieved at transmittances of 90 and 97.5 %, respectively. This method avoided any post-treatments and popularized the application of high-performance Ag NW transparent electrode on more substrates. The improved Ag NWs were successfully employed in a capacitive pressure sensor with high transparency, sensitivity, and reproducibility.
文摘In recent years, advanced composite structures are used extensively in many industries such as aerospace, aircraft, automobile, pipeline and civil engineering. Reliability and safety are crucial requirements posed by them to the advanced composite structures be- cause of their harsh working conditions. Therefore, as a very important measure, structural health monitoring (SHM) in-service is deft- nitely demanded for ensuring their safe working in-situ. In this paper, fiber Bragg grating (FBG) sensors are surface-mounted on the hoop and in the axial directions of a FRP pressure vessel to monitor the strain status during its pressurization. The experimental results show that the FBG sensors could be used to monitor the strain development and determine the ultimate failure strain of the composite pressure vessel.
基金the National Natural Science Foundation of China(NSFC Nos.61674114,91743110,21861132001)National Key Research and Development Program of China(No.2017YFF0204604)+2 种基金Tianjin Applied Basic Research and Advanced Technology(No.17JCJQJC43600)the Foundation for Talent Scientists of Nanchang Institute for Microtechnology of Tianjin Universitythe 111 Project(No.B07014).
文摘Small-sized,low-cost,and high-sensitivity sensors are required for pressure-sensing applications because of their critical role in consumer electronics,automotive applications,and industrial environments.Thus,micro/nanoscale pressure sensors based on micro/nanofabrication and micro/nanoelectromechanical system technologies have emerged as a promising class of pressure sensors on account of their remarkable miniaturization and performance.These sensors have recently been developed to feature multifunctionality and applicability to novel scenarios,such as smart wearable devices and health monitoring systems.In this review,we summarize the major sensing principles used in micro/nanoscale pressure sensors and discuss recent progress in the development of four major categories of these sensors,namely,novel material-based,flexible,implantable,and selfpowered pressure sensors.
基金supported by the National Natural Science Foundation of China(52003253 and 52103308)the China Postdoctoral Science Foundation(2020M672283).
文摘As an indispensable branch of wearable electronics,flexible pressure sensors are gaining tremendous attention due to their extensive applications in health monitoring,human-machine interaction,artificial intelligence,the internet of things,and other fields.In recent years,highly flexible and wearable pressure sensors have been developed using various materials/structures and transduction mechanisms.Morphological engineering of sensing materials at the nanometer and micrometer scales is crucial to obtaining superior sensor performance.This review focuses on the rapid development of morphological engineering technologies for flexible pressure sensors.We discuss different architectures and morphological designs of sensing materials to achieve high performance,including high sensitivity,broad working range,stable sensing,low hysteresis,high transparency,and directional or selective sensing.Additionally,the general fabrication techniques are summarized,including self-assembly,patterning,and auxiliary synthesis methods.Furthermore,we present the emerging applications of high-performing microengineered pressure sensors in healthcare,smart homes,digital sports,security monitoring,and machine learning-enabled computational sensing platform.Finally,the potential challenges and prospects for the future developments of pressure sensors are discussed comprehensively.
基金Project supported by the National Natural Science Foundation of China (Grant Nos 50405025 and 50375050).
文摘This paper reports the current-voltage characteristics of [001]-oriented AlAs/InxGa1-xAs/GaAs resonant tunnelling diodes (RTDs) as a function of uniaxial external stress applied parallel to the [110] and the [1^-10] orientations, and the output characteristics of the GaAs pressure sensor based on the pressure effect on the RTDs. Under [110] stress, the resonance peak voltages of the RTDs shift to more positive voltages. For [1^-10] stress, the peaks shift toward more negative voltages. The resonance peak voltage is linearly dependent on the [110] and [1^-0] stresses and the linear sensitivities are up to 0.69 mV/MPa, -0.69 mV/MPa respectively. For the pressure sensor, the linear sensitivity is up to 0.37 mV/kPa.
基金supported by the National Nature Science Foundation of China(Nos.62122030,61831011,61803171,61722305,61833006,and 21902057)Program for Chang Jiang Scholars and Innovative Research Team in University(No.IRT-17R47)+3 种基金Application and Basic Research of Jilin Province(20130102010 JC)Young Elite Scientists Sponsorship Program by CAST(2018QN RC001)Jilin Province Science and Technology Development Plan Program(20200301010RQ)Fundamental Research Funds for the Central Universities,Graduate Innovation Fund of Jilin University(101832020CX170).
文摘Environmentally friendly degradable sensors with both hazardous gases and pressure efficient sensing capabilities are highly desired for various promising applications,including environmental pollution monitoring/prevention,wisdom medical,wearable smart devices,and artificial intelligence.However,the transient gas and pressure sensors based on only identical sensing material that concurrently meets the above detection needs have not been reported.Here,we present transient all-MXene NO_(2) and pressure sensors employing three-dimensional porous crumpled MXene spheres prepared by ultrasonic spray pyrolysis technology as the sensing layer,accompanied with water-soluble polyvinyl alcohol substrates embedded with patterned MXene electrodes.The gas sensor achieves a ppb-level of highly selective NO_(2) sensing,with a response of up to 12.11%at 5 ppm NO_(2) and a detection range of 50 ppb-5 ppm,while the pressure sensor has an extremely wide linear pressure detection range of 0.14-22.22 kPa and fast response time of 34 ms.In parallel,all-MXene NO_(2) and pressure sensors can be rapidly degraded in medical H_(2)O_(2) within 6 h.This work provides a new avenue toward environmental monitoring,human physiological signal monitoring,and recyclable transient electronics.
文摘In this paper, we present the design, the fabrication, and the experimental results of carbon nanotube (CNT) and Cu20 composite based pressure sensors. The pressed tablets of the CNT Cu20 composite are fabricated at a pressure of 353 MPa. The diameters of the multiwalled nanotubes (MWNTs) are between 10 nm and 30 nm. The sizes of the Cu20 micro particles are in the range of 3-4 μm. The average diameter and the average thickness of the pressed tablets are 10 mm and 4.0 mm, respectively. In order to make low resistance electric contacts, the two sides of the pressed tablet are covered by silver pastes. The direct current resistance of the pressure sensor decreases by 3.3 times as the pressure increases up to 37 kN/m^2. The simulation result of the resistance-pressure relationship is in good agreement with the experimental result within a variation of ±2%.
基金funded by the National Basic Research Program of China (No. 2015CB251201)the NSFC-Shandong Joint Fund for Marine Science Research Centers (No. U1606401)+3 种基金the Scientific and Technological Innovation Project financially supported by Qingdao National Laboratory for Marine Science and Technology (No. 2016ASKJ13)the Major National Science and Technology Programs (No. 016ZX05024-001-002)the Natural Science Foundation of Hainan (No. ZDYF2016215)Key Science and Technology Foundation of Sanya (Nos. 2017PT13, 2017PT2014)
文摘Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure(HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques(PPTs). To improve the accuracy of geopressure prediction in HTHP hydrocarbon reservoirs offshore Hainan Island, we made a comprehensive summary of current PPTs to identify existing problems and challenges by analyzing the global distribution of HTHP hydrocarbon reservoirs, the research status of PPTs, and the geologic setting and its HTHP formation mechanism. Our research results indicate that the HTHP formation mechanism in the study area is caused by multiple factors, including rapid loading, diapir intrusions, hydrocarbon generation, and the thermal expansion of pore fluids. Due to this multi-factor interaction, a cloud of HTHP hydrocarbon reservoirs has developed in the Ying-Qiong Basin, but only traditional PPTs have been implemented, based on the assumption of conditions that do not conform to the actual geologic environment, e.g., Bellotti's law and Eaton's law. In this paper, we focus on these issues, identify some challenges and solutions, and call for further PPT research to address the drawbacks of previous works and meet the challenges associated with the deepwater technology gap. In this way, we hope to contribute to the improved accuracy of geopressure prediction prior to drilling and provide support for future HTHP drilling offshore Hainan Island.
文摘Yinggehai Basin locates in the northern South China Sea. Since the Cainozoic Era, crust has several strong tension: the basin subsides quickly, the deposition is thick, and the crust is thin. In the central basin, formation pressure coefficient is up to 2.1;Yinggehai Basin is a fomous high-temperature overpressure basin.YinggehaiBasin’s in-depth, especially high-temperature overpressure stratum has numerous large-scale exploration goals. As a result of high-temperature overpressure basin’s perplexing geological conditions and geophysical analysis technical limitations, this field of gas exploration can’t be carried out effectively, which affects the process of gas exploration seriously. A pressure prediction model of the high-temperature overpressure basin in different structural positions is summed up by pressure forecast pattern research in recent years, which can be applied to target wells pre-drilling pressure prediction and post drilling pressure analysis of Yinggehai Basin. The model has small erroneous and high rate of accuracy. The Yinggehai Basin A well drilling is successful in 2010, and gas is discovered in high-temperature overpressure stratum, which proved that reservoir can be found in high-temperature overpressure stratum. It is a great theoretical breakthrough of reservoir knowledge.
基金Project supported by the National Natural Science Foundation of China (Grant No.40265001), and the Science Foundation of Yunnan Province (Grant No.2002C0038M)
文摘Aiming at piezoresistive pressure sensors, this paper studies simulation of standard pressure by using benchmark current source and self-calibration of the sampling data characteristics. A data fusion algorithm for sample set is presented which transforms a surface problem into a curve fitting and interpolation problem. The simulation result shows that benchmark current source simulating pressure is successful and data fusion algorithm is effective. The maximum measurement error is only 0.098 kPa and maximum relative error is 0.92% at 0-45 kPa and -10-45~C.
基金Fundamental Research Fund for the Central Universities,China(Nos.2232020G-01 and 19D110106)Young Elite Scientists Sponsorship Program by China Association for Science and Technology,China(No.2017QNRC001)Graduate Student Innovation Fund of Donghua University,China(No.20D310111)。
文摘Flexible piezoresistive pressure sensors can offer convenient detection of mechanical deformations for wearable electronics.Previous studies of flexible piezoresistive pressure sensors focus on the sensitivity but the low-cost and self-powered sensors remain a challenge due to the deviation of resistance signal acquisition caused by thermoelectric voltage.Here,piezoresistive pressure sensors with ultralow Seebeck coefficient of-0.72μV/K based on carbon nanotubes(CNTs)/polyethyleneimine(PEI)/melamine(CPM)sponge are reported.Due to the diminished Seebeck effect,the CPM sponge pressure sensors successfully reduce the deviation to 18.75%and can keep stable sensitivity and resistance change under a very low working voltage and change temperature environment.The stable properties of the sensors make them successful to work for real-time sensing in self-powered wearable electronics.