The dynamic spalling characteristics of rock are important for stability analysis in rock engineering.This paper presented an experimental investigation on the dynamic spalling characteristics of granite with differen...The dynamic spalling characteristics of rock are important for stability analysis in rock engineering.This paper presented an experimental investigation on the dynamic spalling characteristics of granite with different temperatures and strain rates.A series of dynamic spalling tests with different impact velocities were conducted on thermally treated granite at different temperatures.The dynamic spalling strengths of granite with different temperatures and strain rates were determined.A model was proposed to correlate the dynamic spalling strength of granite,high temperature and strain rate.The results show that the spalling strength of granite decreases with increasing temperature.Moreover,the spalling strength of granite with a higher strain rate is larger than that with a lower strain rate.The proposed model can describe the relationship among dynamic spalling strength of granite,high temperature and strain rate.展开更多
High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic ...High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.展开更多
The World Health Organization has declared COVID-19 a pandemic.The demand for devices or systems to diagnose and track COVID-19 infections noninvasively not only in hospitals but also in home settings has led to incre...The World Health Organization has declared COVID-19 a pandemic.The demand for devices or systems to diagnose and track COVID-19 infections noninvasively not only in hospitals but also in home settings has led to increased interest in consumer-grade wearables.A common symptom of COVID-19 is dyspnea,which may manifest as an increase in respiratory and heart rates.In this paper,a novel piezoelectric strain sensor is presented for real-time monitoring of respiratory and heartbeat signals.A highly sensitive and stretchable piezoelectric strain sensor is fabricated using a piezoelectric film with a serpentine layout.The thickness of the patterned PVDF flexible piezoelectric strain sensor is only 168μm,and the voltage sensitivity reaches 0.97 mV/με.The effective modulus is 13.5 MPa,which allows the device to fit to the skin and detect the small strain exhibited by the human body.Chest vibrations are captured by the piezoelectric sensor,which produces an electrical output voltage signal conformally mapped with respiratory–cardiac activities.The separate heart activity and respiratory signals are extracted from the mixed respiratory–cardiac signal by an empirical mode decomposition data processing algorithm.By detecting vital signals such as respiratory and heart rates,the proposed device can aid early diagnosis and monitoring of respiratory diseases such as COVID-19.展开更多
The yeast Pichia pastoris(P. pastoris) has been used for the expression of heterologous proteins with the significant success. However, it is time-consuming to screen the high expression level of the recombinant P. pa...The yeast Pichia pastoris(P. pastoris) has been used for the expression of heterologous proteins with the significant success. However, it is time-consuming to screen the high expression level of the recombinant P. pastoris directly. Thus, for β-mannanase production, developing the accurate, rapid and inexpensive screening method to substitute random screening is certainly required. A simple method based on the size of hydrolysis hole was described here, but this method was not very accurate that could only be used in preliminary screening. To further improve the accuracy, a micro-plate screening method is established, which appears to be more accurate and effective. The efficiency of this screening method is about 10 times higher than that of the general screening strategy of cultivation in shaking flasks. Two methods presented here can also be used for screening of recombinant Pichia strains with high-level expression of other heterologous protein after modification.展开更多
Efficient and reliable removal of cellulose,hemicellulose and lignin,that are the major organic pollutants in the wastewater from regenerated fiber,is critically important to prevent toxicity discharge.Low-and high-pH...Efficient and reliable removal of cellulose,hemicellulose and lignin,that are the major organic pollutants in the wastewater from regenerated fiber,is critically important to prevent toxicity discharge.Low-and high-pH stresses sometimes occur in the effluent treatment systems due to the use of a large amount of acid and alkaline in the pulping process.Using flat separation method to select high-yield strains from bio-contact oxidation basin,seeing configuration of the strains and doing some physiological experiments,we found that the strains contain two kinds of main bacteria,Zoogloea sp.and Pseudomona sp.We also discovered the best growing time by spectrophotometer.The best growing time is at 0~32h,the logarithmic phase is about at 12~32h,and the stable growth phase is about 32~60h.Furthermore,we concluded that the disposal ability of high-yield strain is better than the ordinary one by doing parallel experiment.Through orthogonal test we also confirmed that the best growing temperature and pH value are 29℃and 7.3 respectively.The COD removal rate is about 93% when the biomembrane is in good condition.展开更多
The hot deformation characteristics of 1.4462 duplex stainless steel (DSS) were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenit...The hot deformation characteristics of 1.4462 duplex stainless steel (DSS) were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800-1100~C and strain rates of 0.001-1 s-1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-HoUomon parameter (Z) increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6. x 1015 (lnZ---35.5), a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction (EBSD) confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.展开更多
The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K(0.67Tm-0.76Tm) and high strain rates ranging from 10^-3 to 1 s^...The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K(0.67Tm-0.76Tm) and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding(GBS),and the dislocation creep mechanism is considered as the main accommodation mechanism.展开更多
A β SiC whisker reinforced pure aluminum composites expected to exhibit high strain rate superplasticity has been successfully fabricated by a new processing route consisting of pressure infiltration, extrusion with ...A β SiC whisker reinforced pure aluminum composites expected to exhibit high strain rate superplasticity has been successfully fabricated by a new processing route consisting of pressure infiltration, extrusion with a low extrusion ratio and rolling. The composites exhibite a total elongation of 220%~380% in the initial strain rates within 1.0×10 -2 ~1.0×10 -1 s -1 and at 893~903 K. According to differential thermal analysis(DTA) and microstructure observation, it is concluded that an appropriately small amount of liquid phase is necessary to cause a good high strain rate superplasticity in aluminum matrix composites in addition to fine and uniform microstructure.展开更多
How the wave propagation analysis plays a key role in the studies of dynamic response of materials at high strain rates is analyzed. For the wave propagation technique, the followings are important: the loading and un...How the wave propagation analysis plays a key role in the studies of dynamic response of materials at high strain rates is analyzed. For the wave propagation technique, the followings are important: the loading and unloading constitutive relation presumed, the positions of the sensors embedded, the interactions between loading waves and unloading waves. For the split Hopkinson pressure bar (SHPB) technique, the assumption of one-dimensional stress wave propagation and the assumption of stress uniformity along the specimen should be satisfied. When the larger diameter bars are employed, the wave dispersion effects should be considered, including the high frequency oscillations, non-uniform stress distribution across the bar section, increase of rise time, and amplitude attenuation. The stress uniformity along the specimen is influenced by the reflection times in specimen, the wave impedance ratio of the specimen and the bar, and the waveform.展开更多
Tensile mechanical properties of 1.6Si-1.58Mn-0.195C TRIP (transformation-induced plasticity) steels under high strain rate and effects of DP (dual-phase) treatments were studied and compared to the quasi-static tensi...Tensile mechanical properties of 1.6Si-1.58Mn-0.195C TRIP (transformation-induced plasticity) steels under high strain rate and effects of DP (dual-phase) treatments were studied and compared to the quasi-static tensile behavior. The results show that the increasing of strain rate leads to increasing in their strengths and decreasing in the uniform elongation remarkably. Because the stable retained austenite in TRIP steel can transform to martensite during tensile testing and the material exhibits excellent characteristic of transformation induced plasticity, the plastic deformation behavior is evidently improved and the combination of strength and elongation is superior to that of dual-phase steel, although its strength is smaller than that of DP steel. However, DP treated steel shown lower elongation under dynamic tension in spite of higher strength. A model was proposed to explain the excellent elongation rate of TRIP steel compared with DP steel on the basis of SEM analysis and the strength of the components in microstructure.展开更多
For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical prope...For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical properties of extruded Mg-Gd-Y Magnesium alloy at ambient temperature(300 K),200℃(473 K)and 300℃(573 K)temperature.The samples after compression were analyzed by scanning electron microscope(SEM)and metallographic microscope.Dynamic mechanical properties,crack performance and plastic deformation mechanism of extruded Mg-Gd-Y Magnesium alloy along the extrusion direction(ED)were discussed.The results show that,extruded Mg-Gd-Y Magnesium alloy has the largest dynamic compressive strength which is 535 MPa at ambient temperature(300 K)and strain rate of 2826 s^(−1).When temperature increases,dynamic compressive strength decreases,while ductility increases.The dynamic compression fracture mechanism of extruded Mg-Gd-Y Magnesium alloy is multi-crack propagation and intergranular quasi-cleavage fracture at both ambient temperature and high temperature.The dynamic compressive deformation mechanism of extruded Mg-Gd-Y Magnesium alloy is a combination of twinning,slipping and dynamic recrystallization at both ambient temperature and high temperature.展开更多
In this paper,the superplastic characteristics of the beta-SiC whisker reinforced 2024aluminum composite, fabricated by squeeze casting and hot-rolling after extrusion were investigated. The compsite had a fine grain ...In this paper,the superplastic characteristics of the beta-SiC whisker reinforced 2024aluminum composite, fabricated by squeeze casting and hot-rolling after extrusion were investigated. The compsite had a fine grain size of about 2μm, and exhibited a strain rate sensitivity of about 0.35 and a maximum elongation of 350% at an initial strain rate of 1.1×10-1s-1 at 803K. In addition, the superplastic deformation mechanisme of the composite were also examined.展开更多
The dynamic tensile properties and microstructural evolution of an extruded EW75 magnesium alloy deformed at ambient temperature and different high strain rates(from 1000 to 3000 s^(-1))along extrusion direction(ED)we...The dynamic tensile properties and microstructural evolution of an extruded EW75 magnesium alloy deformed at ambient temperature and different high strain rates(from 1000 to 3000 s^(-1))along extrusion direction(ED)were investigated by Split Hopkinson Tension Bar(SHTB).The corresponding deformation mechanisms,texture evolution and microstructure changes were analyzed by optical microscope(OM),electron backscatter diffraction(EBSD)and transmission electron microscope(TEM).The results show that the extruded EW75 magnesium alloy along ED exhibits a conventional positive strain rate sensitivity that the dynamic flow stresses increase with in creasing strain rate.Texture measurements show that after dynamic tension,the initial weak texture of extruded EW75 magnesium alloy tansforms to a relatively strong<10-10>//ED texture with increasing strain rates.The microstructural analysis demonstrates that dislocation motion are main deformatin mode to accommodate dynamic tensile deformation at high strain rates.In addition,the interactions of dislocation-dislocation and dislocation-second phase lead to the in crease of flow stress and strain hardening with increasing strain rate.展开更多
The stability of cemented paste backfill(CPB)is threatened by dynamic disturbance,but the conventional low strain rate laboratory pressure test has difficulty achieving this research purpose.Therefore,a split Hopkinso...The stability of cemented paste backfill(CPB)is threatened by dynamic disturbance,but the conventional low strain rate laboratory pressure test has difficulty achieving this research purpose.Therefore,a split Hopkinson pressure bar(SHPB)was utilized to investigate the high strain rate compressive behavior of CPB with dynamic loads of 0.4,0.8,and 1.2 MPa.And the failure modes were determined by macro and micro analysis.CPB with different cement-to-tailings ratios,solid mass concentrations,and curing ages was prepared to conduct the SHPB test.The results showed that increasing the cement content,tailings content,and curing age can improve the dynamic compressive strength and elastic modulus.Under an impact load,a higher strain rate can lead to larger increasing times of the dynamic compressive strength when compared with static loading.And the dynamic compressive strength of CPB has an exponential correlation with the strain rate.The macroscopic failure modes indicated that CPB is more seriously damaged under dynamic loading.The local damage was enhanced,and fine cracks were formed in the interior of the CPB.This is because the CPB cannot dissipate the energy of the high strain rate stress wave in a short loading period.展开更多
Static recrystallization of a high strain rate compressed Mg-1 Zn(wt.%)alloy was investigated using electron backscattered diffraction(EBSD).A novel 53°1010 structure was observed in the as-deformed alloy,which s...Static recrystallization of a high strain rate compressed Mg-1 Zn(wt.%)alloy was investigated using electron backscattered diffraction(EBSD).A novel 53°1010 structure was observed in the as-deformed alloy,which showed a{1012}-{1012}double twin relationship with the matrix.When the as-deformed alloy was annealed at 200°C,the{1011}compression twins and{1011}-{1012}double twins showed a higher priority to recrystallize.In addition,the coarse{1012}tension twins and their inner double twins were preferentially to recrystallize,while the lenticular tension twins had little impact on the recrystallization.Therefore,obtaining more compression twins or coarse twins instead of lenticular tension twins can be an effective approach to manipulate recrystallization process in deformed Mg alloys.展开更多
This paper studies surface effects on the mechanical behavior of nanoporous materials under high strains with an improved anisotropic Kelvin model. The stress-strain relations are derived by the theories of Euler-Bern...This paper studies surface effects on the mechanical behavior of nanoporous materials under high strains with an improved anisotropic Kelvin model. The stress-strain relations are derived by the theories of Euler-Bernoulli beam and surface elasticity. Mean- while, the influence of strut (or ligament) size on the mechanical properties of nanoporous materials is discussed, which becomes a key factor with consideration of the residual sur- face stress and the surface elasticity. The results show that the decrease in the strut diameter and the increase in the residual surface stress or the surface elasticity can both lead to an increase in the carrying capacity of nanoporous materials. F^lrthermore, me- chanical behaviors of anisotropic nanoporous materials in different directions (the rise direction and the transverse direction) are investigated. The results indicate that the sur- face effects in the transverse direction are more obvious than those in the rise direction for anisotropic nanoporous materials. In addition, the present results can be reduced to the cases of conventional foams as the strut size increases to micron-scale, which confirms validity of the model to a certain extent.展开更多
Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high...Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high purity aluminum by ECAE at ambient temperature. The experimental results showed that high strain rate and large deformation could induce dynamic recrystallization.Based on dislocation dynamics and grain orientation change enhanced by plastic deformation,a model for the recrystallization process is developed. The model is used to explain the ultra fine grains which are formed at a temperature still much lower than that for the conventional recrystallization展开更多
The relationships between microstructure of 0.195C-1.6Si-1.58 Mn TRIP steel and its dynamic mechanical properties at high strain rate were investigated.The effect of microstructures on dynamic properties was discussed...The relationships between microstructure of 0.195C-1.6Si-1.58 Mn TRIP steel and its dynamic mechanical properties at high strain rate were investigated.The effect of microstructures on dynamic properties was discussed and the comparison with its static mechanical properties was also presented.The specimens of TRIP steel via three heat treatment techniques exhibit different morphological structures,responsible for their dynamic mechanical performances.The dynamic tensile testing was performed on self-made pneumatic tensile impact tester.The results showed that the size,volume fraction,morphology and distribution of retained austenite all affect the final mechanical properties at high strain rate.Among them,the second phase(retained austenite + bainite) with net structure severely decreases the elongation of TRIP steel in spite of the fact that it enhances strength because it restrains ferrite deformation.In order to obtain the excellent combination of strength and elongation,rational matching of morphology,size and volume fraction of several phases in TRIP steel can be obtained via proper heat treatment techniques.展开更多
A self designed Split Hopkinson tensile bar setup with a rotating disk was used to investigate room temperature tensile properties of a γ TiAl alloy in duplex (DP) and fully lamellar (FL) microstructural forms under ...A self designed Split Hopkinson tensile bar setup with a rotating disk was used to investigate room temperature tensile properties of a γ TiAl alloy in duplex (DP) and fully lamellar (FL) microstructural forms under the dynamic strain rates between 70 and 800 s -1 . It was found that for both forms the alloy is brittle at these strain rates, exhibiting near zero ductility. The σ b at dynamic strain rate is greater than that at the static strain rate of 5×10 -1 s -1 , and the σ b of the DP material is higher than that of the FL material. Fractography analysis indicated that both materials at dynamic strain rates fracture in a mixed mode of predominant transgranular cleavage and minor intergranular cracking, which is similar to that at the static strain rate. The room temperature brittleness of the alloy is not environmentally related. : A self designed Split Hopkinson tensile bar setup with a rotating disk was used to investigate room temperature tensile properties of a γ TiAl alloy in duplex (DP) and fully lamellar (FL) microstructural forms under the dynamic strain rates between 70 and 800 s -1 . It was found that for both forms the alloy is brittle at these strain rates, exhibiting near zero ductility. The σ b at dynamic strain rate is greater than that at the static strain rate of 5×10 -1 s -1 , and the σ b of the DP material is higher than that of the FL material. Fractography analysis indicated that both materials at dynamic strain rates fracture in a mixed mode of predominant transgranular cleavage and minor intergranular cracking, which is similar to that at the static strain rate. The room temperature brittleness of the alloy is not environmentally related.展开更多
The true stress-sWain relationships of Ti-5A1-2Sn-2Zr-4Mo-4Cr(TC17) alloy with a wide range of strain rates were investigated by tmiaxial quasi-static and dynamic compression tests, respectively. Quasi- static compr...The true stress-sWain relationships of Ti-5A1-2Sn-2Zr-4Mo-4Cr(TC17) alloy with a wide range of strain rates were investigated by tmiaxial quasi-static and dynamic compression tests, respectively. Quasi- static compression tests were carried out with Instron 8874 test machine, while dynamic compression tests were performed with the split Hopkinson pressure bar (SHPB) which was installed with heating device and synchro- assembly system. The dynamic mechanical behaviors tests of TC17 were carded out from room temperature to 800 ℃ at intervals of 200 ℃ and at high sWain rates (5 500-1 9200 s-l). The stress-strain curves considering temperature-sWain rate coupling actions were obtained. The Johnson-Cook constitutive model was developed through data fitting of the stress-sWain curves. The material constants in the developed constitutive model can be determined using isothermal and adiabatic stress-strain curves at different strain rates. The Johnson-Cook constitutive model provided satisfied prediction of the plastic flow stress for TC17 alloy.展开更多
基金supported by the Beijing Natural Science Foundation,China(Grant No.JQ20039)National Natural Science Foundation of China(Grant No.12172019).
文摘The dynamic spalling characteristics of rock are important for stability analysis in rock engineering.This paper presented an experimental investigation on the dynamic spalling characteristics of granite with different temperatures and strain rates.A series of dynamic spalling tests with different impact velocities were conducted on thermally treated granite at different temperatures.The dynamic spalling strengths of granite with different temperatures and strain rates were determined.A model was proposed to correlate the dynamic spalling strength of granite,high temperature and strain rate.The results show that the spalling strength of granite decreases with increasing temperature.Moreover,the spalling strength of granite with a higher strain rate is larger than that with a lower strain rate.The proposed model can describe the relationship among dynamic spalling strength of granite,high temperature and strain rate.
基金supported by the National Natural Science Foundation of China(Nos.51839009 and 52027814)the Natural Science Foundation of Hubei Province(No.2023AFB589).
文摘High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.
基金We are grateful for funding from the Natural Science Foundation of China(NSFC Grant No.62001322)the Tianjin Municipal Science and Technology Project(No.20JCQNJC011200)+1 种基金the National Key Research and Development Program(No.2020YFB2008801)the Nanchang Institute for Microtechnology of Tianjin University.
文摘The World Health Organization has declared COVID-19 a pandemic.The demand for devices or systems to diagnose and track COVID-19 infections noninvasively not only in hospitals but also in home settings has led to increased interest in consumer-grade wearables.A common symptom of COVID-19 is dyspnea,which may manifest as an increase in respiratory and heart rates.In this paper,a novel piezoelectric strain sensor is presented for real-time monitoring of respiratory and heartbeat signals.A highly sensitive and stretchable piezoelectric strain sensor is fabricated using a piezoelectric film with a serpentine layout.The thickness of the patterned PVDF flexible piezoelectric strain sensor is only 168μm,and the voltage sensitivity reaches 0.97 mV/με.The effective modulus is 13.5 MPa,which allows the device to fit to the skin and detect the small strain exhibited by the human body.Chest vibrations are captured by the piezoelectric sensor,which produces an electrical output voltage signal conformally mapped with respiratory–cardiac activities.The separate heart activity and respiratory signals are extracted from the mixed respiratory–cardiac signal by an empirical mode decomposition data processing algorithm.By detecting vital signals such as respiratory and heart rates,the proposed device can aid early diagnosis and monitoring of respiratory diseases such as COVID-19.
基金Project(CX2012B124)supported by the Graduate Degree Thesis Innovation Program of Hunan ProvinceChina+3 种基金Project(13JJ9002)supported by the Natural Science Foundation of Hunan ProvinceChinaProject(2012XK4081)supported by the Key Science and Technology Plan of Hunan Provincial Science&Technology DepartmentChina
文摘The yeast Pichia pastoris(P. pastoris) has been used for the expression of heterologous proteins with the significant success. However, it is time-consuming to screen the high expression level of the recombinant P. pastoris directly. Thus, for β-mannanase production, developing the accurate, rapid and inexpensive screening method to substitute random screening is certainly required. A simple method based on the size of hydrolysis hole was described here, but this method was not very accurate that could only be used in preliminary screening. To further improve the accuracy, a micro-plate screening method is established, which appears to be more accurate and effective. The efficiency of this screening method is about 10 times higher than that of the general screening strategy of cultivation in shaking flasks. Two methods presented here can also be used for screening of recombinant Pichia strains with high-level expression of other heterologous protein after modification.
文摘Efficient and reliable removal of cellulose,hemicellulose and lignin,that are the major organic pollutants in the wastewater from regenerated fiber,is critically important to prevent toxicity discharge.Low-and high-pH stresses sometimes occur in the effluent treatment systems due to the use of a large amount of acid and alkaline in the pulping process.Using flat separation method to select high-yield strains from bio-contact oxidation basin,seeing configuration of the strains and doing some physiological experiments,we found that the strains contain two kinds of main bacteria,Zoogloea sp.and Pseudomona sp.We also discovered the best growing time by spectrophotometer.The best growing time is at 0~32h,the logarithmic phase is about at 12~32h,and the stable growth phase is about 32~60h.Furthermore,we concluded that the disposal ability of high-yield strain is better than the ordinary one by doing parallel experiment.Through orthogonal test we also confirmed that the best growing temperature and pH value are 29℃and 7.3 respectively.The COD removal rate is about 93% when the biomembrane is in good condition.
文摘The hot deformation characteristics of 1.4462 duplex stainless steel (DSS) were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800-1100~C and strain rates of 0.001-1 s-1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-HoUomon parameter (Z) increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6. x 1015 (lnZ---35.5), a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction (EBSD) confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.
基金supported by the National Natural Science Foundation of China(No.50674067).
文摘The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K(0.67Tm-0.76Tm) and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding(GBS),and the dislocation creep mechanism is considered as the main accommodation mechanism.
文摘A β SiC whisker reinforced pure aluminum composites expected to exhibit high strain rate superplasticity has been successfully fabricated by a new processing route consisting of pressure infiltration, extrusion with a low extrusion ratio and rolling. The composites exhibite a total elongation of 220%~380% in the initial strain rates within 1.0×10 -2 ~1.0×10 -1 s -1 and at 893~903 K. According to differential thermal analysis(DTA) and microstructure observation, it is concluded that an appropriately small amount of liquid phase is necessary to cause a good high strain rate superplasticity in aluminum matrix composites in addition to fine and uniform microstructure.
文摘How the wave propagation analysis plays a key role in the studies of dynamic response of materials at high strain rates is analyzed. For the wave propagation technique, the followings are important: the loading and unloading constitutive relation presumed, the positions of the sensors embedded, the interactions between loading waves and unloading waves. For the split Hopkinson pressure bar (SHPB) technique, the assumption of one-dimensional stress wave propagation and the assumption of stress uniformity along the specimen should be satisfied. When the larger diameter bars are employed, the wave dispersion effects should be considered, including the high frequency oscillations, non-uniform stress distribution across the bar section, increase of rise time, and amplitude attenuation. The stress uniformity along the specimen is influenced by the reflection times in specimen, the wave impedance ratio of the specimen and the bar, and the waveform.
基金the financial supports of Shanghai Development Foun-dation of Auto Industry and the National Natural Science Foundation of China (No. 50171038).
文摘Tensile mechanical properties of 1.6Si-1.58Mn-0.195C TRIP (transformation-induced plasticity) steels under high strain rate and effects of DP (dual-phase) treatments were studied and compared to the quasi-static tensile behavior. The results show that the increasing of strain rate leads to increasing in their strengths and decreasing in the uniform elongation remarkably. Because the stable retained austenite in TRIP steel can transform to martensite during tensile testing and the material exhibits excellent characteristic of transformation induced plasticity, the plastic deformation behavior is evidently improved and the combination of strength and elongation is superior to that of dual-phase steel, although its strength is smaller than that of DP steel. However, DP treated steel shown lower elongation under dynamic tension in spite of higher strength. A model was proposed to explain the excellent elongation rate of TRIP steel compared with DP steel on the basis of SEM analysis and the strength of the components in microstructure.
基金The authors would like to acknowledge the financial support from the National Key Basic Research Program(973 Program),Project(2013CB632205).
文摘For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical properties of extruded Mg-Gd-Y Magnesium alloy at ambient temperature(300 K),200℃(473 K)and 300℃(573 K)temperature.The samples after compression were analyzed by scanning electron microscope(SEM)and metallographic microscope.Dynamic mechanical properties,crack performance and plastic deformation mechanism of extruded Mg-Gd-Y Magnesium alloy along the extrusion direction(ED)were discussed.The results show that,extruded Mg-Gd-Y Magnesium alloy has the largest dynamic compressive strength which is 535 MPa at ambient temperature(300 K)and strain rate of 2826 s^(−1).When temperature increases,dynamic compressive strength decreases,while ductility increases.The dynamic compression fracture mechanism of extruded Mg-Gd-Y Magnesium alloy is multi-crack propagation and intergranular quasi-cleavage fracture at both ambient temperature and high temperature.The dynamic compressive deformation mechanism of extruded Mg-Gd-Y Magnesium alloy is a combination of twinning,slipping and dynamic recrystallization at both ambient temperature and high temperature.
文摘In this paper,the superplastic characteristics of the beta-SiC whisker reinforced 2024aluminum composite, fabricated by squeeze casting and hot-rolling after extrusion were investigated. The compsite had a fine grain size of about 2μm, and exhibited a strain rate sensitivity of about 0.35 and a maximum elongation of 350% at an initial strain rate of 1.1×10-1s-1 at 803K. In addition, the superplastic deformation mechanisme of the composite were also examined.
基金The authors would like to thank Professor Kui Zhang,Beijing General Research Institute for Nonferrous Metal,for providing EW75 magnesium alloy for this work and acknowledge the funding from the Natural Science Foundation of the Jiangsu Higher Education Institutions of China(Grant No.17KJD430006)Scientific and Technological Innovation Team Foundation of Wuxi Institute of Technology(No.30593118001)Scientific Research Project of Wuxi Institute of Technology(No.ZK201901).The help of EBSD experiment provided by Yukyung Shin from Helmholtz-Zentrum Geesthacht is gratefully acknowledged.
文摘The dynamic tensile properties and microstructural evolution of an extruded EW75 magnesium alloy deformed at ambient temperature and different high strain rates(from 1000 to 3000 s^(-1))along extrusion direction(ED)were investigated by Split Hopkinson Tension Bar(SHTB).The corresponding deformation mechanisms,texture evolution and microstructure changes were analyzed by optical microscope(OM),electron backscatter diffraction(EBSD)and transmission electron microscope(TEM).The results show that the extruded EW75 magnesium alloy along ED exhibits a conventional positive strain rate sensitivity that the dynamic flow stresses increase with in creasing strain rate.Texture measurements show that after dynamic tension,the initial weak texture of extruded EW75 magnesium alloy tansforms to a relatively strong<10-10>//ED texture with increasing strain rates.The microstructural analysis demonstrates that dislocation motion are main deformatin mode to accommodate dynamic tensile deformation at high strain rates.In addition,the interactions of dislocation-dislocation and dislocation-second phase lead to the in crease of flow stress and strain hardening with increasing strain rate.
基金supported by the National Key R&D Program of China(No.2017YFC0602902)the National Natural Scienceof China(Nos.41807259 and 51874350)+2 种基金the Fundamental Research Funds for the Central Universities of Central South University(No.2016zztx096)The support provided by the China Scholarship Council(CSC)during the visit of the first author toécole Polytechnique de Montréal(Student ID:201706370039)the materials supply by Fan Kou lead-zinc mine of Shenzhen Zhongjin Lingnan Non-ferrous metal Company Limited。
文摘The stability of cemented paste backfill(CPB)is threatened by dynamic disturbance,but the conventional low strain rate laboratory pressure test has difficulty achieving this research purpose.Therefore,a split Hopkinson pressure bar(SHPB)was utilized to investigate the high strain rate compressive behavior of CPB with dynamic loads of 0.4,0.8,and 1.2 MPa.And the failure modes were determined by macro and micro analysis.CPB with different cement-to-tailings ratios,solid mass concentrations,and curing ages was prepared to conduct the SHPB test.The results showed that increasing the cement content,tailings content,and curing age can improve the dynamic compressive strength and elastic modulus.Under an impact load,a higher strain rate can lead to larger increasing times of the dynamic compressive strength when compared with static loading.And the dynamic compressive strength of CPB has an exponential correlation with the strain rate.The macroscopic failure modes indicated that CPB is more seriously damaged under dynamic loading.The local damage was enhanced,and fine cracks were formed in the interior of the CPB.This is because the CPB cannot dissipate the energy of the high strain rate stress wave in a short loading period.
基金financially supported by National Natural Science Foundation of China(No.51701121,No.51825101)Shanghai Sailing Program(17YF1408800)+2 种基金Science and Technology Commission of Shanghai Municipality(No.18511109302)Qinghai Provincial Science and Technology Key Program(No.2018-GX-A1)Startup Fund for Youngman Research at SJTU(No.18X100040022)
文摘Static recrystallization of a high strain rate compressed Mg-1 Zn(wt.%)alloy was investigated using electron backscattered diffraction(EBSD).A novel 53°1010 structure was observed in the as-deformed alloy,which showed a{1012}-{1012}double twin relationship with the matrix.When the as-deformed alloy was annealed at 200°C,the{1011}compression twins and{1011}-{1012}double twins showed a higher priority to recrystallize.In addition,the coarse{1012}tension twins and their inner double twins were preferentially to recrystallize,while the lenticular tension twins had little impact on the recrystallization.Therefore,obtaining more compression twins or coarse twins instead of lenticular tension twins can be an effective approach to manipulate recrystallization process in deformed Mg alloys.
基金supported by the National Natural Science Foundation of China(Nos.11472025,10932001,and 11272030)
文摘This paper studies surface effects on the mechanical behavior of nanoporous materials under high strains with an improved anisotropic Kelvin model. The stress-strain relations are derived by the theories of Euler-Bernoulli beam and surface elasticity. Mean- while, the influence of strut (or ligament) size on the mechanical properties of nanoporous materials is discussed, which becomes a key factor with consideration of the residual sur- face stress and the surface elasticity. The results show that the decrease in the strut diameter and the increase in the residual surface stress or the surface elasticity can both lead to an increase in the carrying capacity of nanoporous materials. F^lrthermore, me- chanical behaviors of anisotropic nanoporous materials in different directions (the rise direction and the transverse direction) are investigated. The results indicate that the sur- face effects in the transverse direction are more obvious than those in the rise direction for anisotropic nanoporous materials. In addition, the present results can be reduced to the cases of conventional foams as the strut size increases to micron-scale, which confirms validity of the model to a certain extent.
文摘Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high purity aluminum by ECAE at ambient temperature. The experimental results showed that high strain rate and large deformation could induce dynamic recrystallization.Based on dislocation dynamics and grain orientation change enhanced by plastic deformation,a model for the recrystallization process is developed. The model is used to explain the ultra fine grains which are formed at a temperature still much lower than that for the conventional recrystallization
基金Item Sponsored by National Natural Science Foundation of China(50171038)Shanghai Development Foundation of Auto Industry
文摘The relationships between microstructure of 0.195C-1.6Si-1.58 Mn TRIP steel and its dynamic mechanical properties at high strain rate were investigated.The effect of microstructures on dynamic properties was discussed and the comparison with its static mechanical properties was also presented.The specimens of TRIP steel via three heat treatment techniques exhibit different morphological structures,responsible for their dynamic mechanical performances.The dynamic tensile testing was performed on self-made pneumatic tensile impact tester.The results showed that the size,volume fraction,morphology and distribution of retained austenite all affect the final mechanical properties at high strain rate.Among them,the second phase(retained austenite + bainite) with net structure severely decreases the elongation of TRIP steel in spite of the fact that it enhances strength because it restrains ferrite deformation.In order to obtain the excellent combination of strength and elongation,rational matching of morphology,size and volume fraction of several phases in TRIP steel can be obtained via proper heat treatment techniques.
文摘A self designed Split Hopkinson tensile bar setup with a rotating disk was used to investigate room temperature tensile properties of a γ TiAl alloy in duplex (DP) and fully lamellar (FL) microstructural forms under the dynamic strain rates between 70 and 800 s -1 . It was found that for both forms the alloy is brittle at these strain rates, exhibiting near zero ductility. The σ b at dynamic strain rate is greater than that at the static strain rate of 5×10 -1 s -1 , and the σ b of the DP material is higher than that of the FL material. Fractography analysis indicated that both materials at dynamic strain rates fracture in a mixed mode of predominant transgranular cleavage and minor intergranular cracking, which is similar to that at the static strain rate. The room temperature brittleness of the alloy is not environmentally related. : A self designed Split Hopkinson tensile bar setup with a rotating disk was used to investigate room temperature tensile properties of a γ TiAl alloy in duplex (DP) and fully lamellar (FL) microstructural forms under the dynamic strain rates between 70 and 800 s -1 . It was found that for both forms the alloy is brittle at these strain rates, exhibiting near zero ductility. The σ b at dynamic strain rate is greater than that at the static strain rate of 5×10 -1 s -1 , and the σ b of the DP material is higher than that of the FL material. Fractography analysis indicated that both materials at dynamic strain rates fracture in a mixed mode of predominant transgranular cleavage and minor intergranular cracking, which is similar to that at the static strain rate. The room temperature brittleness of the alloy is not environmentally related.
基金Funded by the National Basic Research Program of China(No.2009CB724401)the Major Science and Technology Program of High-end CNC Machine Tools and Basic Manufacturing Equipment(No.2012ZX04003-041)
文摘The true stress-sWain relationships of Ti-5A1-2Sn-2Zr-4Mo-4Cr(TC17) alloy with a wide range of strain rates were investigated by tmiaxial quasi-static and dynamic compression tests, respectively. Quasi- static compression tests were carried out with Instron 8874 test machine, while dynamic compression tests were performed with the split Hopkinson pressure bar (SHPB) which was installed with heating device and synchro- assembly system. The dynamic mechanical behaviors tests of TC17 were carded out from room temperature to 800 ℃ at intervals of 200 ℃ and at high sWain rates (5 500-1 9200 s-l). The stress-strain curves considering temperature-sWain rate coupling actions were obtained. The Johnson-Cook constitutive model was developed through data fitting of the stress-sWain curves. The material constants in the developed constitutive model can be determined using isothermal and adiabatic stress-strain curves at different strain rates. The Johnson-Cook constitutive model provided satisfied prediction of the plastic flow stress for TC17 alloy.