The electronic structure of （001） polar surface of cubic zirconia was studied by GGA（WC） approximation. We found the cubic lattice near （001） surface showed an intensive tendency to transfer to tetragonal lattic...The electronic structure of （001） polar surface of cubic zirconia was studied by GGA（WC） approximation. We found the cubic lattice near （001） surface showed an intensive tendency to transfer to tetragonal lattice. The metallic state appeared on both the terminations. For O-termination, some O2p states were vacated and hole carriers concentrated on surface oxygen-ions. For Zr-termination, some Zr4d states became partial occupied for the loss of O2p states. We observed the hole states were mainly localized at the corresponding ions on surface for both the terminations, while the charge states on Zr-termination were dispersed on surface.展开更多
In aero-engines,mortise-tenon joint structures are often used to connect the blades to the turbine disk.The disadvantages associated with conventional manufacturing techniques mean that a low-cost,high-efficiency,and ...In aero-engines,mortise-tenon joint structures are often used to connect the blades to the turbine disk.The disadvantages associated with conventional manufacturing techniques mean that a low-cost,high-efficiency,and high-quality nickel-based mortise–tenon joint structure is an urgent requirement in the field of aviation engineering.Electrochemical cutting is a potential machining method for manufacturing these parts,as there is no tool degradation in the cutting process and high-quality surfaces can be obtained.To realize the electrochemical cutting of a mortise-tenon joint structure,a method using a tube electrode with helically distributed jet-flow holes on the side-wall is proposed.During feeding,the tube electrode rotates along its central axis.Flow field simulations show that the rotational speed of the tube electrode determines the direct spraying time of the high-speed electrolyte ejected from the jet-flow holes to the machining area,while the electrolyte pressure determines the flow rate of the electrolyte and the velocity of the electrolyte ejected from the jet-flow holes.The machining results using the proposed method are verified experimentally,and the machining parameters are optimized.Finally,mortise and tenon samples are successfully machined using 20 mm thick Inconel 718 alloy with a feeding rate of 5μm/s.展开更多
基金Supported by the National Hi-tech Research and Development Program of China(No.2006AA11A189)the Key Project of Science and Technology Committee of Shanghai(No.06DZ12212)the Project of National Engineering Research Center of Advanced Steely Technology(No.050209)
文摘The electronic structure of （001） polar surface of cubic zirconia was studied by GGA（WC） approximation. We found the cubic lattice near （001） surface showed an intensive tendency to transfer to tetragonal lattice. The metallic state appeared on both the terminations. For O-termination, some O2p states were vacated and hole carriers concentrated on surface oxygen-ions. For Zr-termination, some Zr4d states became partial occupied for the loss of O2p states. We observed the hole states were mainly localized at the corresponding ions on surface for both the terminations, while the charge states on Zr-termination were dispersed on surface.
基金supported by the National Natural Science Foundation of China(No.91960204)the Natural Science Foundation of Jiangsu Province(No.BK20191279)+1 种基金the Aeronautical Science Foundation of China(No.201907052002)the National Natural Science Foundation of China for Creative Research Groups(No.51921003)。
文摘In aero-engines,mortise-tenon joint structures are often used to connect the blades to the turbine disk.The disadvantages associated with conventional manufacturing techniques mean that a low-cost,high-efficiency,and high-quality nickel-based mortise–tenon joint structure is an urgent requirement in the field of aviation engineering.Electrochemical cutting is a potential machining method for manufacturing these parts,as there is no tool degradation in the cutting process and high-quality surfaces can be obtained.To realize the electrochemical cutting of a mortise-tenon joint structure,a method using a tube electrode with helically distributed jet-flow holes on the side-wall is proposed.During feeding,the tube electrode rotates along its central axis.Flow field simulations show that the rotational speed of the tube electrode determines the direct spraying time of the high-speed electrolyte ejected from the jet-flow holes to the machining area,while the electrolyte pressure determines the flow rate of the electrolyte and the velocity of the electrolyte ejected from the jet-flow holes.The machining results using the proposed method are verified experimentally,and the machining parameters are optimized.Finally,mortise and tenon samples are successfully machined using 20 mm thick Inconel 718 alloy with a feeding rate of 5μm/s.
