Self-assembled monolayers(SAMs)have recently emerged as excellent hole transport materials in inverted perovskite solar cells(PSCs)owing to their ability to minimize parasitic absorption,regulate energy level alignmen...Self-assembled monolayers(SAMs)have recently emerged as excellent hole transport materials in inverted perovskite solar cells(PSCs)owing to their ability to minimize parasitic absorption,regulate energy level alignment,and passivate perovskite defects.Herein,we design and synthesize a novel dimethyl acridinebased SAM,[2-(9,10-dihydro-9,9-dimethylacridine-10-yl)ethyl]phosphonic acid(2PADmA),and employ it as a hole-transporting layer in inverted PSCs.Experimental results show that the 2PADmA SAM can modulate perovskite crystallization,facilitate carrier transport,passivate perovskite defects,and reduce nonradiative recombination.Consequently,the 2PADmA-based device achieves an enhanced power conversion efficiency(PCE)of 24.01%and an improved fill factor(FF)of 83.92%compared to the commonly reported[2-(9H-carbazol-9-yl)ethyl]phosphonic acid(2PACz)-based control device with a PCE of 22.32%and FF of 78.42%,while both devices exhibit comparable open-circuit voltage and short-circuit current density.In addition,2PADmA-based devices exhibit outstanding dark storage and thermal stabilities,retaining approximately~98%and 87%of their initial PCEs after 1080 h of dark storage and 400 h of heating at 85°C,respectively,both considerably superior to the control device.展开更多
We improve the performance of organic light-emitting diodes （OLEDs） with both a MoO3 hole injection layer （HIL） and a MoO3 doped hole transport layer （HTL）, and present a systematical and comparative investigati...We improve the performance of organic light-emitting diodes （OLEDs） with both a MoO3 hole injection layer （HIL） and a MoO3 doped hole transport layer （HTL）, and present a systematical and comparative investigation on these devices. Compared with OLEDs with only MoO3 HIL or MoO3 doped HTL, OLEDs with both MoO3 HIL and MoO3 doped HTL show superior performance in driving voltage, power efficiency, and stability. Based on the typical NPB/Alq3 heterojunction structure, OLEDs with both MoO3 HIL and MoO3 doped HTL show a driving voltage of 5.4 V and a power efficiency of 1.41 lm/W for 1000 cd/m2, and a lifetime of around 0. 88 h with an initial luminance of 5268 cd/m2 under a constant current of 190 mA/cm2 operation in air without encapsulation. While OLEDs with only MoO3 HIL or MoO3 doped HTL show higher driving voltages of 6.4 V or 5.8 V and lower power efficiencies of 1.201m/W or 1.341m/W for 1000cd/m2, and a shorter lifetime of 0.33 or 0.60h with an initial luminance of around 5122 or 5300cd/m2 under a constant current of 200 or 216mA/cm2 operation. Our results demonstrate clearly that using both MoO3 HIL and MoO3 doped HTL is a simple and effective approach to simultaneoasly improve both the hole injection and transport efficiency, resulting from the lowered energy barrier at the anode interface and the increased hole carrier density in MoO3 doped HTL.展开更多
A bilayer model with ohmic anode contact and injection limited cathode contact has been proposed to calculate the recombination efficiency and recombination zone width of the device. The effects of the thickness of ho...A bilayer model with ohmic anode contact and injection limited cathode contact has been proposed to calculate the recombination efficiency and recombination zone width of the device. The effects of the thickness of hole transport layer and the barriers of organic/organic interface on the combination efficiency and recombination width have been discussed. It is found that： （1） When the electrons are blocked fully and the holes are not blocked significantly at the organic/organic interface, for a given Lh/L, the recombination efficiency increases with increasing the applied voltage, but at a higher applied voltage, the recombination efficiency decreases with increasing Lh/L; （2） The recombination efficiency increases with increasing applied voltage and Hh＇, and when applied voltage and Hh＇ exceed some value, the recombination efficiency appears as a plateau; （3） The recombination width decreases with increasing the applied voltage and Lh/L. This model might explain the relative experiment phenomena.展开更多
The organic light-emitting devices(OLEDs) using 4,4',4''-tris{N-(3-methylphenyl)-N-phenylamin}triphenylamine(m-MTDATA) and MoO_3 or 1,3,5-triazo-2,4,6-triphosphorine-2,2,4,4,6,6-tetrachloride(TAPC) and MoO...The organic light-emitting devices(OLEDs) using 4,4',4''-tris{N-(3-methylphenyl)-N-phenylamin}triphenylamine(m-MTDATA) and MoO_3 or 1,3,5-triazo-2,4,6-triphosphorine-2,2,4,4,6,6-tetrachloride(TAPC) and MoO_3 as the hole-injection layer(HIL) were fabricated. MoO_3 can be expected to be a good injection layer material and thus enhance the emission performance of OLED. The highest occupied molecular(HOMO) of MoO_3 is between those of m-MTDATA or TAPC and N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine(NPB),which reduces the hole-injection barrier and improves the luminance of the OLEDs. The current efficiency is improved compared with that of the device without the MoO_3 layer. The highest luminous efficiency of the device with 2-nm-thick MoO_3 as HIL is achieved as 5.27 cd/A at 10 V,which is nearly 1.2 times larger than that of the device without it. Moreover,the highest current efficiency and power efficiency of the device with the structure indium-tin oxide(ITO)/TAPC(40 nm)/MoO_3(2 nm)/Tc Ta:Ir(ppy)3(10%,10 nm)/ tris-(8-hydroxyquinoline) aluminium(Alq)(60 nm)/Li F(1 nm)/Al are achieved as 37.15 cd/A and 41.23 lm/W at 3.2 V and 2.8 V,respectively.展开更多
近几年,钙钛矿太阳电池(perovskite solar cells,PSCs)成为光伏领域研究的热点.自2009年,在短短10年时间内PSCs效率就从3. 8%迅速提升至24. 2%,其效率几乎可以与传统硅电池相媲美,然而较差的稳定性阻碍了PSCs实用化的进程.PSCs的稳定性...近几年,钙钛矿太阳电池(perovskite solar cells,PSCs)成为光伏领域研究的热点.自2009年,在短短10年时间内PSCs效率就从3. 8%迅速提升至24. 2%,其效率几乎可以与传统硅电池相媲美,然而较差的稳定性阻碍了PSCs实用化的进程.PSCs的稳定性主要包括钙钛矿材料及其他功能层材料的稳定性,因此,重点探讨了水、氧、光、热等环境因素对钙钛矿材料以及PSCs稳定性的影响规律,以及导致其性能衰退的主要原因.同时,分析并总结了如何利用钙钛矿组分及结构优化、界面修饰、电荷传输层材料改进、封装等方式来提升PCSs稳定性的可行性.展开更多
In this review, we highlight the recent development of organic π-functional materials as buffer layers in constructing efficient perovskite solar cells（PVSCs）. By following a brief introduction on the PVSC developm...In this review, we highlight the recent development of organic π-functional materials as buffer layers in constructing efficient perovskite solar cells（PVSCs）. By following a brief introduction on the PVSC development, device architecture and material design features, we exemplified the exciting progresses made in field by exploiting organic π-functional materials based hole and electron transport layers（HTLs and ETLs） to enable high-performance PVSCs.展开更多
In recent years,the perovskite solar cells have gained much attention because of their ever-increasing power conversion efficiency(PCE),simple solution fabrication process,flyable,light-weight wearable and deployable ...In recent years,the perovskite solar cells have gained much attention because of their ever-increasing power conversion efficiency(PCE),simple solution fabrication process,flyable,light-weight wearable and deployable for ultra-lightweight space and low-cost materials constituents etc.Over the last few years,the efficiency of perovskite solar cells has surpassed 25%due to high-quality perovskite-film accomplished through low-temperature synthesis techniques along with developing suitable interface and electrode-materials.Besides,the stability of perovskite solar cells has attracted much well-deserved attention.In this article we have focused on recent progress of the perovskite solar cells regarding their crystallinity,morphology and synthesis techniques.Also,demonstrated different layers such as electron transport-layers(ETLs),hole transport-layers(HTLs)and buffer-layers utilized in perovskite solar-cells,considering their band gap,carrier mobility,transmittance etc.Outlook of various tin(Sn),carbon and polymer-based perovskite solar cells and their potential of commercialization feasibility has also been discussed.展开更多
基金National Natural Science Foundation of China(Grant Nos.51925206,52302052)the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB0450301)+1 种基金Yunnan Provincial Science and Technology Project at Southwest United Graduate School(Grant No.202302AO370013)Huacai Solar Co.,Ltd.
文摘Self-assembled monolayers(SAMs)have recently emerged as excellent hole transport materials in inverted perovskite solar cells(PSCs)owing to their ability to minimize parasitic absorption,regulate energy level alignment,and passivate perovskite defects.Herein,we design and synthesize a novel dimethyl acridinebased SAM,[2-(9,10-dihydro-9,9-dimethylacridine-10-yl)ethyl]phosphonic acid(2PADmA),and employ it as a hole-transporting layer in inverted PSCs.Experimental results show that the 2PADmA SAM can modulate perovskite crystallization,facilitate carrier transport,passivate perovskite defects,and reduce nonradiative recombination.Consequently,the 2PADmA-based device achieves an enhanced power conversion efficiency(PCE)of 24.01%and an improved fill factor(FF)of 83.92%compared to the commonly reported[2-(9H-carbazol-9-yl)ethyl]phosphonic acid(2PACz)-based control device with a PCE of 22.32%and FF of 78.42%,while both devices exhibit comparable open-circuit voltage and short-circuit current density.In addition,2PADmA-based devices exhibit outstanding dark storage and thermal stabilities,retaining approximately~98%and 87%of their initial PCEs after 1080 h of dark storage and 400 h of heating at 85°C,respectively,both considerably superior to the control device.
基金Supported by the National Natural Science Foundation of China under Grant No 11274402the National Basic Research Program of China under Grant No 2012CB933704+1 种基金the Natural Science Foundation of Guangdong Province under Grant No S2012020011003the Program for Changjiang Scholars and Innovative Research Team in University under Grant No IRT13042
文摘We improve the performance of organic light-emitting diodes （OLEDs） with both a MoO3 hole injection layer （HIL） and a MoO3 doped hole transport layer （HTL）, and present a systematical and comparative investigation on these devices. Compared with OLEDs with only MoO3 HIL or MoO3 doped HTL, OLEDs with both MoO3 HIL and MoO3 doped HTL show superior performance in driving voltage, power efficiency, and stability. Based on the typical NPB/Alq3 heterojunction structure, OLEDs with both MoO3 HIL and MoO3 doped HTL show a driving voltage of 5.4 V and a power efficiency of 1.41 lm/W for 1000 cd/m2, and a lifetime of around 0. 88 h with an initial luminance of 5268 cd/m2 under a constant current of 190 mA/cm2 operation in air without encapsulation. While OLEDs with only MoO3 HIL or MoO3 doped HTL show higher driving voltages of 6.4 V or 5.8 V and lower power efficiencies of 1.201m/W or 1.341m/W for 1000cd/m2, and a shorter lifetime of 0.33 or 0.60h with an initial luminance of around 5122 or 5300cd/m2 under a constant current of 200 or 216mA/cm2 operation. Our results demonstrate clearly that using both MoO3 HIL and MoO3 doped HTL is a simple and effective approach to simultaneoasly improve both the hole injection and transport efficiency, resulting from the lowered energy barrier at the anode interface and the increased hole carrier density in MoO3 doped HTL.
基金Excellent Youth Foundation of Hunan Province(03JJY1008) Science Foundation for Post-doctorate of China(2004035083)
文摘A bilayer model with ohmic anode contact and injection limited cathode contact has been proposed to calculate the recombination efficiency and recombination zone width of the device. The effects of the thickness of hole transport layer and the barriers of organic/organic interface on the combination efficiency and recombination width have been discussed. It is found that： （1） When the electrons are blocked fully and the holes are not blocked significantly at the organic/organic interface, for a given Lh/L, the recombination efficiency increases with increasing the applied voltage, but at a higher applied voltage, the recombination efficiency decreases with increasing Lh/L; （2） The recombination efficiency increases with increasing applied voltage and Hh＇, and when applied voltage and Hh＇ exceed some value, the recombination efficiency appears as a plateau; （3） The recombination width decreases with increasing the applied voltage and Lh/L. This model might explain the relative experiment phenomena.
基金supported by the Major Project of Science and Technology Office of Fujian Province of China(No.2014H0042)the Natural Science Foundation of Fujian Province of China(No.2015J01664)the Project of Science and Technology Research of Quanzhou City in Fujian Province of China(Nos.2013Z125 and 2014Z137)
文摘The organic light-emitting devices(OLEDs) using 4,4',4''-tris{N-(3-methylphenyl)-N-phenylamin}triphenylamine(m-MTDATA) and MoO_3 or 1,3,5-triazo-2,4,6-triphosphorine-2,2,4,4,6,6-tetrachloride(TAPC) and MoO_3 as the hole-injection layer(HIL) were fabricated. MoO_3 can be expected to be a good injection layer material and thus enhance the emission performance of OLED. The highest occupied molecular(HOMO) of MoO_3 is between those of m-MTDATA or TAPC and N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine(NPB),which reduces the hole-injection barrier and improves the luminance of the OLEDs. The current efficiency is improved compared with that of the device without the MoO_3 layer. The highest luminous efficiency of the device with 2-nm-thick MoO_3 as HIL is achieved as 5.27 cd/A at 10 V,which is nearly 1.2 times larger than that of the device without it. Moreover,the highest current efficiency and power efficiency of the device with the structure indium-tin oxide(ITO)/TAPC(40 nm)/MoO_3(2 nm)/Tc Ta:Ir(ppy)3(10%,10 nm)/ tris-(8-hydroxyquinoline) aluminium(Alq)(60 nm)/Li F(1 nm)/Al are achieved as 37.15 cd/A and 41.23 lm/W at 3.2 V and 2.8 V,respectively.
文摘近几年,钙钛矿太阳电池(perovskite solar cells,PSCs)成为光伏领域研究的热点.自2009年,在短短10年时间内PSCs效率就从3. 8%迅速提升至24. 2%,其效率几乎可以与传统硅电池相媲美,然而较差的稳定性阻碍了PSCs实用化的进程.PSCs的稳定性主要包括钙钛矿材料及其他功能层材料的稳定性,因此,重点探讨了水、氧、光、热等环境因素对钙钛矿材料以及PSCs稳定性的影响规律,以及导致其性能衰退的主要原因.同时,分析并总结了如何利用钙钛矿组分及结构优化、界面修饰、电荷传输层材料改进、封装等方式来提升PCSs稳定性的可行性.
基金financial support from the 973 program(No.2014CB643503)the National Natural Science Foundation of China(No.21474088)+2 种基金financial support from NSFC(No.21674093)the National 1000 Young Talents Program hosted by China100 Talents Program by Zhejiang University
文摘In this review, we highlight the recent development of organic π-functional materials as buffer layers in constructing efficient perovskite solar cells（PVSCs）. By following a brief introduction on the PVSC development, device architecture and material design features, we exemplified the exciting progresses made in field by exploiting organic π-functional materials based hole and electron transport layers（HTLs and ETLs） to enable high-performance PVSCs.
文摘In recent years,the perovskite solar cells have gained much attention because of their ever-increasing power conversion efficiency(PCE),simple solution fabrication process,flyable,light-weight wearable and deployable for ultra-lightweight space and low-cost materials constituents etc.Over the last few years,the efficiency of perovskite solar cells has surpassed 25%due to high-quality perovskite-film accomplished through low-temperature synthesis techniques along with developing suitable interface and electrode-materials.Besides,the stability of perovskite solar cells has attracted much well-deserved attention.In this article we have focused on recent progress of the perovskite solar cells regarding their crystallinity,morphology and synthesis techniques.Also,demonstrated different layers such as electron transport-layers(ETLs),hole transport-layers(HTLs)and buffer-layers utilized in perovskite solar-cells,considering their band gap,carrier mobility,transmittance etc.Outlook of various tin(Sn),carbon and polymer-based perovskite solar cells and their potential of commercialization feasibility has also been discussed.
