352-Gbit/s single line rate THz wired transmission based on PS-4096QAM employing hollow-core fiber

We successfully demonstrate 32-Gbaud Probabilistically Shaped 4096-ary Quadrature Amplitude Modulation(PS-4096QAM)TeraHertz(THz)signal wired transmission at 325 GHz over the 1-m Hollow-Core Fiber(HCF)in a photon-assisted THz-wave communication system.By employing advanced Digital Signal Processing(DSP)and the PS technique,the 352-Gbit/s line rate(288-Gbit/s net rate)delivery with a net Spectral Efficiency(SE)of 9 bit/s/Hz is realized in the experiment,satisfying the 0.86-Normalized Generalized Mutual Information(NGMI)Low-Density Parity-Check(LDPC)threshold.

Microstructural evolution and strengthening mechanism of aligned steel fiber cement-based tail backfills exposed to electromagnetic induction

Cemented tailings backfill(CTB)not only boosts mining safety and cuts surface environmental pollution but also recovers ores previously retained as pillars,thereby improving resource utilization.The use of alternative reinforcing products,such as steel fiber(SF),has continuously strengthened CTB into SFCTB.This approach prevents strength decreases over time and reinforces its long-term durability,especially when mining ore in adjacent underground stopes.In this study,various microstructure and strength tests were performed on SFCTB,considering steel fiber ratio and electromagnetic induction strength effects.Lab findings show that combining steel fibers and their distribution dominantly influences the improvement of the fill’s strength.Fill’s strength rises by fiber insertion and has an evident correlation with fiber insertion and magnetic induction strength.When magnetic induction strength is 3×10^(-4) T,peak uniaxial compressive stress reaches 5.73 MPa for a fiber ratio of 2.0vol%.The cracks’expansion mainly started from the specimen’s upper part,which steadily expanded downward by increasing the load until damage occurred.The doping of steel fiber and its directional distribution delayed crack development.When the doping of steel fiber was 2.0vol%,SFCTBs showed excellent ductility characteristics.The energy required for fills to reach destruction increases when steel-fiber insertion and magnetic induction strength increase.This study provides notional references for steel fibers as underground filling additives to enhance the fill’s durability in the course of mining operations.

Broadband all-fiber optical phase modulator based on photo-thermal effect in a gas-filled hollow-core fiber

We report broadband all-fiber optical phase modulation based on the photo-thermal effect in a gas-filled hollow-core fiber.The phase modulation dynamics are studied by multi-physics simulation.A phase modulator is fabricated using a 5.6-cm-long anti-resonant hollow-core fiber with pure acetylene filling.It has a half-wave optical power of 289 mW at 100 kHz and an average insertion loss 0.6 dB over a broad wavelength range from 1450 to 1650 nm.The rise and fall time constants are 3.5 and 3.7μs,respectively,2–3 orders of magnitude better than the previously reported microfiber-based photo-thermal phase modulators.The gas-filled hollow-core waveguide configuration is promising for optical phase modulation from ultraviolet to mid-infrared which is challenging to achieve with solid optical fibers.

Effect of polytetrafluoroethylene hollow fiber microstructure on formaldehyde carbonylation performance in membrane contactor

Membrane contactor is regarded as a promising method for reaction and process intensification. The feasibility of formaldehyde carbonylation to synthesize glycolic acid using polytetrafluoroethylene(PTFE)membrane contactor has been proved in our previous study. In this paper, the effect of membrane microstructure on process performance was further investigated. Three porous PTFE hollow fibers with different pore sizes and one polydimethylsiloxane(PDMS)/PTFE composite membrane with dense layer were fabricated for comparison. The physical and chemical properties of four membranes, including chemical composition, morphology, contact angle, liquid entry pressure, thermodynamic analysis and gas permeability, were systemically characterized. Experiments of formaldehyde carbonylation under different reaction conditions were conducted. The results indicated that the yield of glycolic acid increased with decreasing pore size for porous membranes, which was due to the improvement of wetting behavior. The dense layer of PDMS in composite hollow fiber could effectively prevent the solvent from entering membrane pores, thus the membrane exhibited the best performance. At reaction temperature of 120℃ and operation pressure of 3.0 MPa, the yield of glycolic acid was always higher than 90% as the mass ratio of trioxane and phosphotungstic acid increased from 0.2:1 to 0.8:1. The highest turnover frequency was up to 26.37 mol·g^(-1)·h^(-1). This study provided a reference for the understanding and optimization of membrane contactors for the synthesis of glycolic acid using solvent with low surface tension.

Influence of recycled carbon fiber addition on the microstructure and creep response of extruded AZ91 magnesium alloy

In this study,the recycled short carbon fiber(CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion.The objective was to investigate the impact of CF content(2.5 and 5.0 wt.%)and fiber length(100 and 500μm)on the microstructure,mechanical properties,and creep behavior of AZ91 alloy matrix.The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy.In comparison to the unreinforced AZ91 alloy,the composites with 2.5 wt.%CF exhibited an increase in hardness by 16-20%and yield strength by 5-15%,depending on the fiber length,while experiencing a reduction in ductility.When the reinforcement content was increased from 2.5 to 5.0 wt.%,strength values exhibited fluctuations and decline,accompanied by decreased ductility.These divergent outcomes were discussed in relation to fiber length,clustering tendency due to higher reinforcement content,and the presence of interfacial products with micro-cracks at the CF-matrix interface.Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy,suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep.

Microstructure of Steel Fiber Reinforced Polymer-cement-based Composites

Mercury intrusion porosimetry was used to measure the pore structure of steel fiber reinforced polymer-cement-based composite. The results indicate that the large pore volume decreases by 57. 8% - 51.2% and by 87. 1% - 88% with the addition of steel fibers and polymers respectively. When both steel fibers and polymers are simultaneously added, the large pore volume decreases by 88.3% - 90.1% . As a surface active material , polymer has a favorable water-reduced and forming-film effect, which is contributed to the decrease of the thickness of water film and the improvement of the conglutination between the fibers and the matrix. Polymers could form a microstructure network. This network structure and the bone structure of cement hydration products penetrate each other and thus the interpenetrating network with sticky aggregate and steel fiber inside forms.

The stress-microstructure relationship in an evolving mixing layer of fiber suspensions

The equations for fiber suspensions in an evolving mixing layer were solved by the spectral method, and the trajectory and orientation of fibers were calculated based on the slender body theory. The calculated spatial and orientation distributions of fibers are consistent with the experimental ones that were performed in this paper. The relationship between the microstructure of fibers and additional stress was examined. The results show that the spatial and orientation distributions of fibers are heterogeneous because of the influence of coherent vortices in the flow, which leads to the heterogeneity of the additional stress. The degree of heterogeneity increases with the increasing of St number and fiber aspect ratio. The fibers in the flow make the momentum loss thickness of the mixing layer thicker and accelerate the vorticity dispersion.

Effect of wheat bran insoluble dietary fiber with different particle size on the texture properties, protein secondary structure, and microstructure of noodles

This study was conducted to explore how the insoluble dietary fiber(IDF)of wheat bran with different particle size affects the texture properties,water distribution,protein secondary structure and microstructure of noodles.The results suggested that IDF addition increased the cooking loss and decreased the sensory evaluation because of the damage on dough structure,while as the IDF particle size decreased,the sensory score increased from 78.8 to 82.3 and cooking loss decreased from 8.65%to 7.65%,which could be attributed to that small particle-sized IDF limited the damage on protein network structure,decreased the T22 and t-structure,and increased the β1-structure.Moreover,IDF particle size had a significant correlation with protein secondary structures,texture properties and evaluation score of noodles.In conclusion,adding appropriate particle sizewould be an effectiveway of enhancing the nutritional and textural properties of noodles.

Nonlinear compression of picosecond chirped pulse from thin-disk amplifier system through a gas-filled hollow-core fiber

We theoretically study the nonlinear compression of a 20-rnJ, 1030-nm picosecond chirped pulse from the thin-disk amplifier in a krypton gas-filled hollow-core fiber. The chirp from the thin-disk amplifier system has little influence on the initial pulse, however, it shows an effect on the nonlinear compression in hollow-core fiber. We use a large diameter hollow waveguide to restrict undesirable nonlinear effects such as ionization; on the other hand, we employ suitable gas pressure and fiber length to promise enough spectral broadening; with 600-μm, 6-bar （1 bar = 105 Pa）, 1.8-m hollow fiber, we obtain 31.5-fs pulse. Moreover, we calculate and discuss the optimal fiber lengths and gas pressures with different initial durations induced by different grating compression angles for reaching a given bandwidth. These results are meaningful for a compression scheme from picoseconds to femtoseconds.

Investigating the Microstructure of Slenderized Wool Fibers at Different Stretching Ratios by Raman Spectroscopy

The molecular conformation and the microstructure of the slenderized wool fibers have been studied by the Raman spectroscopy. The typical bands analyzed in this paper include the amideⅠand amide Ⅲ regions, the CC skeletal vibration region, and the SS and CS bond vibration regions. The experimental results show that ⅰ) the Raman spectroscopy can reveal the secondary structural transformation from αhelical to βpleated sheet begin at the early stage of stretching; ⅱ) the stretching mechanism of wool fibers can be divided into two different mechanisms, i.e. the secondary structural transformation and the slippage of the polypeptide chain; and ⅲ) the stretching leads to the increasing of the amount of the disordered conformation and the decreasing of the amount of SS bonds.

Picosecond pulses compression at 1053-nm center wavelength by using a gas-filled hollow-core fiber compressor

We theoretically study the nonlinear compression of picosecond pulses with 10-m J of input energy at the 1053-nm center wavelength by using a one-meter-long gas-filled hollow-core fiber（HCF） compressor and considering the third-order dispersion（TOD） effect. It is found that when the input pulse is about 1 ps/10 m J, it can be compressed down to less than20 fs with a high transmission efficiency. The gas for optimal compression is krypton gas which is filled in a HCF with a 400-μm inner diameter. When the input pulse duration is increased to 5 ps, it can also be compressed down to less than 100 fs efficiently under proper conditions. The results show that the TOD effect has little impact on picosecond pulse compression and the HCF compressor can be applied on compressing picosecond pulses efficiently with a high compression ratio, which will benefit the research of high-field laser physics.

Highly efficient Cherenkov radiation generation in the irregular point of hollow-core photonic crystal fiber

Highly efficient Cherenkov radiation （CR） is generated by the soliton self-frequency shift （SSFS） in the irregular point of a hollow-core photonic crystal fiber （HC-PCF） in our laboratory. The impacts of pump power and wavelength on the CR are investigated, and the corresponding nonlinear processes are discussed. When the average power of the 120 fs pump pulse increases from 500 mW to 700 mW, the Raman soliton shifts from 2210 nm to 2360 nm, the output power of the CR increases by 2.3 times, the maximum output power ratio of the CR at 539 nm to that of the residual pump is calculated to be 24.32：1, the width of the output optical spectrum at the visible wavelength broadens from 35 nm to 62 nm, and the conversion efficiency η of the CR in the experiment can be above 32%.

Microstructure characteristics and liquation behavior of fiber laser welded joints of Mg-5Zn-1Mn-0.6Sn alloy sheets

Fine-grained Mg?5Zn?1Mn?0.6Sn alloy sheets of2mm in thickness were welded by fiber laser welding.The appearanceand microstructures of the welding joints and liquation behaviors in the partially melted zone(PMZ)were investigated.The resultsshow that,with the lower welding power and higher welding speed,the width and depth of the joints decrease.Moreover,some poresare detected at a very high welding speed.There are two kinds of liquation phenomena in the PMZ.One is the liquation networkalong grain boundaries associated with the liquation of substrate and segregation-induced liquation,the other is the molten poolinvolved with the liquation of the residual second phases at the boundaries.However,the liquation of substrate and thesegregation-induced liquation are the main liquation mechanism in the PMZ.

Microstructure of Carbon Fiber and Carbon Reinforced Plastic

This study is the investigation of the microstructure of different types of carbon fiber. They were compared with the carbonized and graphitized fibers. Results of structural researches have been presented. It was found that the damage varies from different pollution and the damage of the monofibers. The effect of the pollution of the monofiber was determined.

Effect of Nitriding Process on Phase and Microstructure of Silicon Nitride Fibers Prepared by Direct Nitriding Method

In this paper,Si3N4 fiber materials were fabricated by nitridation of porous Si green bodies,which were prepared by the foaming method combined with gel-casting.The effect of the nitriding process(the heating rate and the nitrogen flow rate)on the phase and the microstructure was studied.The results show that decreasing the heating rate and the nitrogen flow rate is both beneficial to the growth of Si3N4 nanofibers and promoting the disintegration of the pore wall structure of the porous green bodies.The optimized nitrogen flow rate and the heating rate for the growth of silicon nitride fibers are 150 mL/min and 0.5℃/min,respectively.

Broadband tunable Raman soliton self-frequency shift to mid-infrared band in a highly birefringent microstructure fiber

Raman soliton self-frequency shifted to mid-infrared band（λ 〉 2 μm） has been achieved in an air-silica microstructure fiber（MF）. The MF used in our experiment has an elliptical core with diameters of 1.08 and 2.48 μm for fast and slow axis. Numerical simulation shows that each fundamental orthogonal polarization mode has two wide-spaced λZDW and theλZDW pairs located at 701/2110 nm and 755/2498 nm along the fast and slow axis, respectively. Using 810-nm Ti：sapphire femtosecond laser as pump, when the output power varies from 0.3 to 0.5 W, the furthest red-shift Raman solitons in both fast and slow axis shift from near-infrared band to mid-infrared band, reaching as far as 2030 and 2261 nm. Also, midinfrared Raman solitons can always be generated for pump wavelength longer than 790 nm if output pump power reaches0.5 W. Specifically, with pump power at 0.5 W, the mid-infrared soliton in slow axis shifts from 2001 to 2261 nm when the pump changes from 790 nm to 810 nm. This means only a 20 nm change of pump results in 260 nm tunability of a mid-infrared soliton.

Application of different fiber structures and arrangements by electrospinning in triboelectric nanogenerators

In recent years,nanogenerators(NGs)have attracted wide attention in the energy field,among which triboelectric nanogenerators(TENGs)have shown superior performance.Multiple reports of electrospinning(ES)-based TENGs have been reported,but there is a lack of deep analysis of the designing method from microstructure,limiting the creative of new ES-based TENGs.Most TENGs use polymer materials to achieve corresponding design,which requires structural design of polymer materials.The existing polymer molding design methods include macroscopic molding methods,such as injection,compression,extrusion,calendering,etc.,combined with liquid-solid changes such as soluting and melting;it also includes micro-nano molding technology,such as melt-blown method,coagulation bath method,ES method,and nanoimprint method.In fact,ES technology has good controllability of thickness dimension and rich means of nanoscale structure regulation.At present,these characteristics have not been reviewed.Therefore,in this paper,we combine recent reports with some microstructure regulation functions of ES to establish a more general TENGs design method.Based on the rich microstructure research results in the field of ES,much more new types of TENGs can be designed in the future.

Effects of precoating and calcination on microstructure of 3D silica fiber reinforced silicon nitride based composites

Three-dimensional silica fiber reinforced silicon nitride based composites were fabricated by preceramic polymer infiltration and pyrolysis method using perhydropolysilazane as a precursor. The effects of precoating and high temperature calcination on the microstructures of the composites were investigated by scanning electron microscopy. For the composite without a precoating, the fracture surface is plain, and the fiber/matrix interfaces become very unclear after calcination at 1 600 ℃ due to intense interfacial reactions. The composite with a precoating shows tough fracture surface with distinct fiber pull-outs, and the fiber/matrix interfaces are still clear after calcination at 1 600 ℃. It is the appropriate precoating process that contributes to the good interfacial microstructures for the composite.

Experimental study on the Stokes effect in disordered birefringent microstructure fibers

In this paper, a 120-fs pulse transmission experiment is carried out using disordered birefringent microstructure fibers with cladding ventages. Through this experiment, it is found for the first time that remarkable Stokes and anti-Stokes waves can also be produced when the central wavelength of the incident pulse is in the normal dispersion regime of the microstructure fiber. The generation of the two waves can be explained by the four-wave mixing phase matching theory. Properties of the two waves under the action of femtosecond laser pulses with different parameters are studied. The results show that the central wavelength of anti-Stokes waves and Stokes waves produced under the two orthogonal polarization states shift by 63 nm and 160 nm, respectively. The strengths and central positions of the two waves in birefringent fibers can be controlled by adjusting the phase match condition and the polarization directions of incident pulses.

Effect of High-temperature Annealing on Mechanical Performance and Microstructures of Different Oxygen SiC Fibers

In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide（SiC）-based fibers, specified as XD-SiC fibers（low oxygen） and Nicalon-201 fibers（high oxygen）, were annealed in Ar for 1 h at 800 ℃, 1 000 and 1 200 ℃, respectively. Mechanical properties of these fibers were characterized via a monofilament tensile method, with observation of the damaged monofilament by SEM. Also, the effects of annealing on the microstructure and chemical compositions of the fibers were studied. The experimental results indicated that the tensile strength decreased with the increase of annealing temperatures,after annealing-treatment at 1200℃, XD-SiC fibers remained 84% of its original strength, while Nicalon-201 fibers remained only 58% of its original strength. Crystallization and chemical composition of the fibers are the dominating factors for their mechanical performance at high temperatures. The microstructure changes of XD-SiC fibers are mainly composed of the growth of β-SiC, for Nicalon-201 fibers, evaporation of gases is the main change for microstructure.