Bulk anisotropic Sm_(2)Co_(7) nanocrystalline magnets were successfully prepared by hot deformation process using spark plasma sintering technology.The coercivity of the isotropic Sm_(2)Co_(7) nanocrystalline magnet i...Bulk anisotropic Sm_(2)Co_(7) nanocrystalline magnets were successfully prepared by hot deformation process using spark plasma sintering technology.The coercivity of the isotropic Sm_(2)Co_(7) nanocrystalline magnet is 34.76 kOe,further,the ultra-high coercivity of 50.68 kOe is obtained in the anisotropic hot deformed Sm_(2)Co_(7) magnet when the height reduction is70%,which is much higher than those of the ordinarily produced hot deformed Sm_(2)Co_(7) magnet.X-ray diffraction(XRD)analysis shows that all the samples are Sm_(2)Co_(7) single phase.The investigation by electron backscatter diffraction indicates that increasing the amount of deformation is beneficial to the improvement of the(001) texture of Sm_(2)Co_(7) magnets.The Sm_(2)Co_(7) nanocrystalline magnet generates a strong c-axis crystallographic texture during large deformation process.展开更多
Fine-grained Nd10.79Pr2.8Al0.4B7.72Fe78.29 magnets were prepared by low temperature pre-sintering and subsequent hot pressing. The grain size of the magnets is just about 1–3 μm because the low sintering temperature...Fine-grained Nd10.79Pr2.8Al0.4B7.72Fe78.29 magnets were prepared by low temperature pre-sintering and subsequent hot pressing. The grain size of the magnets is just about 1–3 μm because the low sintering temperature results in no grain growth. The orientation degree, microstructure, and magnetic properties were studied. Some grains＇ easy axes deviate from the orientation direction, possibly due to grain rotation during the hot pressing. By subsequent annealing, the magnetic properties were significantly enhanced. Especially, the squareness of the demagnetization curve was improved greatly.The enhancement of coercivity by annealing can be explained by an improvement of both grain boundaries and magnetic isolation, which decouples the exchange interaction between neighboring grains.展开更多
Zn1-xCoxO diluted magnetic semiconductor bulks were prepared by hot pressing.Mixed powders of pure ZnO and CoO were compacted under pressure of 10 MPa at the temperature of 1 073 K.Then the samples were annealed in va...Zn1-xCoxO diluted magnetic semiconductor bulks were prepared by hot pressing.Mixed powders of pure ZnO and CoO were compacted under pressure of 10 MPa at the temperature of 1 073 K.Then the samples were annealed in vacuum at the temperature from 673 K to 873 K for 10 h.The crystal structure and magnetic properties of Zn1-xCoxO bulks have been investigated by X-ray diffraction（XRD） and vibrating sample magnetometer（VSM）.X-ray photoelectron spectroscopy（XPS） was used to study chemical valence of zinc and cobalt in the samples.The results showed that Zn1-xCoxO samples had c-axis oriented wurtzite symmetry,neither cobalt or cobalt oxide phase was found in the samples if x was less than 0.15.Zn and Co existed in Zn0.9Co0.1O sample in Zn2＋ and Co2＋ states.The results of VSM experiment proved the room temperature ferromagnetic properties（RTFP） of Co-doped ZnO samples.The saturation magnetization and the coercivity of Zn0.9Co0.1O sample,observed in the M-H curve,were about 0.20 emu/g and 200 Oe,respectively.展开更多
The effect of hot-pressing techniques on the magnetic properties of Pr-Fe-B alloys has been studied in this paper. The results show that the main factors influencing the magnetic properties for hot-pressing magnet are...The effect of hot-pressing techniques on the magnetic properties of Pr-Fe-B alloys has been studied in this paper. The results show that the main factors influencing the magnetic properties for hot-pressing magnet are hot-pressing temperature, thickness reduction and strain rates. When the hot-pressing temperature is 800℃ and thickness reduction is 75%, the best magnetic properties are obtained as Br = 1.04 T, iHc = 1016 kA/m,(BH)max=201 kJ/m3.展开更多
Microstructures and magnetic properties of Fe84Nb7B9,Fe80Ti8B 12 and Fe32Ni36（Nb/V）7Si8B17 powders and their bulk alloys prepared by mechanical alloying（MA） method and hot-press sintering were studied. The results...Microstructures and magnetic properties of Fe84Nb7B9,Fe80Ti8B 12 and Fe32Ni36（Nb/V）7Si8B17 powders and their bulk alloys prepared by mechanical alloying（MA） method and hot-press sintering were studied. The results show that: 1) After MA for 20 h,nanocrystalline bcc singl e phase supersaturated solid solution forms in Fe84-Nb7B9 and Fe8 0Ti8B12 alloys,amorphous structure forms in Fe32Ni36Nb7 Si8B17 alloy,duplex microstructure composed of nanocrystalline γ- （FeNi） supersaturated solid solution and trace content of Fe2B phase forms in Fe32Ni36-V7Si8B17 alloy. 2) The decomposition process of supersaturated solid solution phases in Fe84Nb7B9 and Fe80Ti8B 12 alloys happens at 710780 ℃,crystallization reaction in Fe （32）Ni36Nb7Si8B17 alloy happens at 530 ℃（the temperature of peak value） and residual amorphous crystallized further happens at 760 ℃ （the temperature of peak value）,phase decomposition process of supersaturated solid solution at 780 ℃ （the temperature of peak value） and crystallization reaction at 431 ℃ （the temperature of peak value） happens in Fe32Ni36V7S i8B17 alloy. 3) under 900 ℃,30 MPa,（0.5 h） hot-press sintering conditions,bulk alloys with high relative density（94.7%95.8%） can be ob tained. Except that the grain size of Fe84Nb7B9 bulk alloy is large,s uperfine grains （grain size 50200 nm） are obtained in other alloys. Exc ept that single phase microstructure is obtained in Fe80Ti8B12 bul k alloy,multi-phase microstructures are obtained in other alloys. 4) The magne tic properties of Fe80Ti8B12bulk alloy（Bs=1.74 T,Hc= 4.35 kA/m） are significantly superior to those of other bulk alloys,which is r elated to the different phases of nanocrystalline or amorphous powder formed dur ing hot-press sintering process and grain size.展开更多
Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechani...Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechanism.Regression analysis shows that the intrinsic coercivity varies inversely as the logarithm of the average grain size: _iH_c(MA/m)=1.7312-0.48161nd(μm) which confirms the randomness of nucleation of reversed domains and the statistical nature of coercivity,indicating that the decrease of grain size would reduce the average number of de- fects on its surface and lower the probability of magnetization reversal of a grain and the cu- mulative fraction of the grains that have reversed their magnetization.Coercivity is thus en- hanced.展开更多
Structure and magnetic properties were studied for bulk nanocrystalline Nd-Fe-B permanent magnets that were prepared at 650 ℃ for 3 min under 300 MPa using the SPS-3.20-MK-V sintering machine and the hot pressed magn...Structure and magnetic properties were studied for bulk nanocrystalline Nd-Fe-B permanent magnets that were prepared at 650 ℃ for 3 min under 300 MPa using the SPS-3.20-MK-V sintering machine and the hot pressed magnets were then submitted to hot deformation with height reduction of 50%, 60%, 70%, 80%, and 85%. Effects of height reduction （HR） and deformation temperature on the structure and magnetic properties of the magnets were investigated. The crystal structure was evaluated by means of X-ray diffraction （XRD） and the microstructure was observed by transmission electron microscopy （TEM）. The magnetic properties of the magnets were investigated by vibrating sample magnetometer （VSM）. As the height reduction increased, the remanence （Br） of the magnets increased first, peaks at 1.3 T with HR=60%, then decreased again, and the coercivity （Hci） of the magnets decreased monotonically. On the other hand, as the deformation temperature increased, the Br of the magnets increased first, peaks at 1.36 T with HR=60%, then decreased again, and the H^i of the magnets decreased monotonically. Under optimal conditions, the hot deformed magnet possessed excellent magnetic properties as Brl.36 T, Hci=1143 kA/m, and （BH）max=370 kJ/m3, suggesting the good potential of the magnets in practical applications.展开更多
The surface of gadolinium was covered with a layer of Al film(10-15 μm) by hot-press.Corrosion resistance, thermal conductivity and diffusivity of the composites were studied. As a result,temperature and pressure are...The surface of gadolinium was covered with a layer of Al film(10-15 μm) by hot-press.Corrosion resistance, thermal conductivity and diffusivity of the composites were studied. As a result,temperature and pressure are the main factors that influence the combination of Gd and Al, and the effect of pressure is especially obvious. When the pressure exceeds 700 MPa, the binding force reaches 9 MPa. After coating, corrosion resistance of the composites is significantly improved, Corrosion rate is significantly reduced and mass loss reduced to one-tenth of pure Gd after 15 days. The current density decreases by an order of magnitude and corrosion potential increases by 0.3 V. The thermal conductivity of the composites is 11.12 W·m^-1·K^-1. Due to good thermal diffusion coefficient of aluminum, the magnetic work piece coated with Al film might show better heat transfer performance.展开更多
基金Project supports by the Science Center of the National Natural Science Foundation of China(Grant No.52088101)the National Natural Foundation of China(Grant No.51590880)+2 种基金the Fujian Institute of Innovation,Chinese Academy of Sciences(Grant No.FJCXY18040302)the Key Program of the Chinese Academy of Sciences(Grant No.KJZD-EW-M05-1)the Natural Science Foundation of Inner Mongolia,China(Grant Nos.2018LH05006 and2018LH05011)。
文摘Bulk anisotropic Sm_(2)Co_(7) nanocrystalline magnets were successfully prepared by hot deformation process using spark plasma sintering technology.The coercivity of the isotropic Sm_(2)Co_(7) nanocrystalline magnet is 34.76 kOe,further,the ultra-high coercivity of 50.68 kOe is obtained in the anisotropic hot deformed Sm_(2)Co_(7) magnet when the height reduction is70%,which is much higher than those of the ordinarily produced hot deformed Sm_(2)Co_(7) magnet.X-ray diffraction(XRD)analysis shows that all the samples are Sm_(2)Co_(7) single phase.The investigation by electron backscatter diffraction indicates that increasing the amount of deformation is beneficial to the improvement of the(001) texture of Sm_(2)Co_(7) magnets.The Sm_(2)Co_(7) nanocrystalline magnet generates a strong c-axis crystallographic texture during large deformation process.
基金Project supported by the National Natural Science Foundation of China(Grant No.51101167)the National Science and Technology Major Project,China(Grant No.2012ZX02702006-005)+2 种基金the Local Cooperation Project of Chinese Academy of Sciences(Grant No.DBSH-2011-013)the Natural Science Foundation of Zhejiang Province,China(Grant No.LQ14E010007)the Natural Science Foundation of Ningbo,China(Grant No.2014A610161)
文摘Fine-grained Nd10.79Pr2.8Al0.4B7.72Fe78.29 magnets were prepared by low temperature pre-sintering and subsequent hot pressing. The grain size of the magnets is just about 1–3 μm because the low sintering temperature results in no grain growth. The orientation degree, microstructure, and magnetic properties were studied. Some grains＇ easy axes deviate from the orientation direction, possibly due to grain rotation during the hot pressing. By subsequent annealing, the magnetic properties were significantly enhanced. Especially, the squareness of the demagnetization curve was improved greatly.The enhancement of coercivity by annealing can be explained by an improvement of both grain boundaries and magnetic isolation, which decouples the exchange interaction between neighboring grains.
基金Funded by the Innovative Scientific Research Foundation of Shanghai Education Committee (No.09YZ367)
文摘Zn1-xCoxO diluted magnetic semiconductor bulks were prepared by hot pressing.Mixed powders of pure ZnO and CoO were compacted under pressure of 10 MPa at the temperature of 1 073 K.Then the samples were annealed in vacuum at the temperature from 673 K to 873 K for 10 h.The crystal structure and magnetic properties of Zn1-xCoxO bulks have been investigated by X-ray diffraction（XRD） and vibrating sample magnetometer（VSM）.X-ray photoelectron spectroscopy（XPS） was used to study chemical valence of zinc and cobalt in the samples.The results showed that Zn1-xCoxO samples had c-axis oriented wurtzite symmetry,neither cobalt or cobalt oxide phase was found in the samples if x was less than 0.15.Zn and Co existed in Zn0.9Co0.1O sample in Zn2＋ and Co2＋ states.The results of VSM experiment proved the room temperature ferromagnetic properties（RTFP） of Co-doped ZnO samples.The saturation magnetization and the coercivity of Zn0.9Co0.1O sample,observed in the M-H curve,were about 0.20 emu/g and 200 Oe,respectively.
文摘The effect of hot-pressing techniques on the magnetic properties of Pr-Fe-B alloys has been studied in this paper. The results show that the main factors influencing the magnetic properties for hot-pressing magnet are hot-pressing temperature, thickness reduction and strain rates. When the hot-pressing temperature is 800℃ and thickness reduction is 75%, the best magnetic properties are obtained as Br = 1.04 T, iHc = 1016 kA/m,(BH)max=201 kJ/m3.
文摘Microstructures and magnetic properties of Fe84Nb7B9,Fe80Ti8B 12 and Fe32Ni36（Nb/V）7Si8B17 powders and their bulk alloys prepared by mechanical alloying（MA） method and hot-press sintering were studied. The results show that: 1) After MA for 20 h,nanocrystalline bcc singl e phase supersaturated solid solution forms in Fe84-Nb7B9 and Fe8 0Ti8B12 alloys,amorphous structure forms in Fe32Ni36Nb7 Si8B17 alloy,duplex microstructure composed of nanocrystalline γ- （FeNi） supersaturated solid solution and trace content of Fe2B phase forms in Fe32Ni36-V7Si8B17 alloy. 2) The decomposition process of supersaturated solid solution phases in Fe84Nb7B9 and Fe80Ti8B 12 alloys happens at 710780 ℃,crystallization reaction in Fe （32）Ni36Nb7Si8B17 alloy happens at 530 ℃（the temperature of peak value） and residual amorphous crystallized further happens at 760 ℃ （the temperature of peak value）,phase decomposition process of supersaturated solid solution at 780 ℃ （the temperature of peak value） and crystallization reaction at 431 ℃ （the temperature of peak value） happens in Fe32Ni36V7S i8B17 alloy. 3) under 900 ℃,30 MPa,（0.5 h） hot-press sintering conditions,bulk alloys with high relative density（94.7%95.8%） can be ob tained. Except that the grain size of Fe84Nb7B9 bulk alloy is large,s uperfine grains （grain size 50200 nm） are obtained in other alloys. Exc ept that single phase microstructure is obtained in Fe80Ti8B12 bul k alloy,multi-phase microstructures are obtained in other alloys. 4) The magne tic properties of Fe80Ti8B12bulk alloy（Bs=1.74 T,Hc= 4.35 kA/m） are significantly superior to those of other bulk alloys,which is r elated to the different phases of nanocrystalline or amorphous powder formed dur ing hot-press sintering process and grain size.
文摘Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechanism.Regression analysis shows that the intrinsic coercivity varies inversely as the logarithm of the average grain size: _iH_c(MA/m)=1.7312-0.48161nd(μm) which confirms the randomness of nucleation of reversed domains and the statistical nature of coercivity,indicating that the decrease of grain size would reduce the average number of de- fects on its surface and lower the probability of magnetization reversal of a grain and the cu- mulative fraction of the grains that have reversed their magnetization.Coercivity is thus en- hanced.
基金Project supported by National High Technology Research and Development Program of China(2010AA03A402)State Key Development Program of Basic Research of China(2010CB934600)
文摘Structure and magnetic properties were studied for bulk nanocrystalline Nd-Fe-B permanent magnets that were prepared at 650 ℃ for 3 min under 300 MPa using the SPS-3.20-MK-V sintering machine and the hot pressed magnets were then submitted to hot deformation with height reduction of 50%, 60%, 70%, 80%, and 85%. Effects of height reduction （HR） and deformation temperature on the structure and magnetic properties of the magnets were investigated. The crystal structure was evaluated by means of X-ray diffraction （XRD） and the microstructure was observed by transmission electron microscopy （TEM）. The magnetic properties of the magnets were investigated by vibrating sample magnetometer （VSM）. As the height reduction increased, the remanence （Br） of the magnets increased first, peaks at 1.3 T with HR=60%, then decreased again, and the coercivity （Hci） of the magnets decreased monotonically. On the other hand, as the deformation temperature increased, the Br of the magnets increased first, peaks at 1.36 T with HR=60%, then decreased again, and the H^i of the magnets decreased monotonically. Under optimal conditions, the hot deformed magnet possessed excellent magnetic properties as Brl.36 T, Hci=1143 kA/m, and （BH）max=370 kJ/m3, suggesting the good potential of the magnets in practical applications.
基金Funded by the National Natural Science Foundation of China(No.51176050)
文摘The surface of gadolinium was covered with a layer of Al film(10-15 μm) by hot-press.Corrosion resistance, thermal conductivity and diffusivity of the composites were studied. As a result,temperature and pressure are the main factors that influence the combination of Gd and Al, and the effect of pressure is especially obvious. When the pressure exceeds 700 MPa, the binding force reaches 9 MPa. After coating, corrosion resistance of the composites is significantly improved, Corrosion rate is significantly reduced and mass loss reduced to one-tenth of pure Gd after 15 days. The current density decreases by an order of magnitude and corrosion potential increases by 0.3 V. The thermal conductivity of the composites is 11.12 W·m^-1·K^-1. Due to good thermal diffusion coefficient of aluminum, the magnetic work piece coated with Al film might show better heat transfer performance.
