Ventilated Double Skin Facades in Hot-Summer and Cold-Winter Zones in China

Double-skin facades(DSF)are a technique developed for colder climates,so few people think about whether or not it can also be used for hot-summer and cold-winter zones in China.After analyzing the problems of using DSF for hot-summer zones,this paper explored on the possibility of applying DSF in hot-summer and cold-winter zones in China.The main existing research methods for DSF were also collected and commented.If properly managed,the ventilated DSF with controlled shading devices can be used even in hot summer in China.

Suitability and Construction of Self-Insulation Walls in the Hot Summer and Cold Winter Zone of Southern Shaanxi

In this paper, the suitability and construction technology of self-insulation walls were studied under the specific climatic conditions and regional resources of Hanzhong and Ankang in the hot summer and cold winter zone of Southern Shaanxi. Through the calculation of heat transfer coefficient and thermal inertia index, combined with the specifications of the shale hollow brick and aerated concrete block of Hanzhong and Ankang in southern Shaanxi, the thermal performance and suitable thickness of the external wall using self-insulation materials that meet the Design Standard for Energy Efficiency of Residential Buildings(DBJ61-65-2011) in Shaanxi Province were obtained. The results showed that the self-insulation wall had technical suitability in the hot summer and cold winter zone. The research results provide not only a theoretical basis for the external wall insulation design of urban residential buildings in the hot summer and cold winter zone of southern Shaanxi, but also a reference for designers to carry out energy-saving design of external walls of residential buildings in other similar climate zones.

The Theoretically Studies and Field Testing of Self-Insulation Exterior Wall in the Hot Summer and Cold Winter Zone

The energy efficiency design of the exterior wall in the buildings of the hot summer and cold winter zone of China should consider the heat prevention in summer and the heat insulation in winter. The self-insulation of the exterior?wall is a more feasible design to satisfy the energy efficiency of buildings in the?zone. However, the systematic research is urgently needed for the self-insulation of the exterior wall in the hot summer and cold winter zone of China. The paper tested the thermal performance of the common non-clay materials such as shale sintered hollow brick, sand autoclaved aerated concrete block, etc. by means of indoor experiments. The energy efficiency effect of the common materials was verified using dynamic calculation soft PKPM and several constitutions of exterior wall with different main bricks and insulation materials on the heat bridge were simulated, too. Besides, the tests of the thermal performance of exterior wall in real constructions were carried out to testify the practical effect of the recommended constitutions of exterior wall with different main bricks and insulation materials on the heat bridge. The conclusions are: the physical and thermal properties of the six non-clay wall material are better than the clay porous brick;the thermal performance of the non-clay brick can be improved obviously through the rational arrangement of the holes;shale sintered hollow brick after increasing the holes and rationalizing the hole arrangement and sand autoclaved aerated concrete block are recommended for buildings in the hot summer and cold winter area of China. The dynamic calculation results show that the thermal performances?of the non-clay materials are all satisfied with the energy efficiency;The heat transfer coefficient of the exterior wall with composition?③,?in which?the main wall was sand autoclaved aerated concrete block and the material on the heat bridge was sand autoclaved aerated concrete plate, is the smallest among the three recommended compositions.

Research on Passive Design Optimization about an Experimental Rural Residence in Hot Summer and Cold Winter Region of China

In China, rural residential environment under the poor construction measures has not been satisfactory due to the backward infrastructure of countryside and the lacking of professional planning, which will result in considerable amount of energy consumption in the future. The economy of rural residences in the hot summer and cold winter region of China is relative developed, but the indoor thermal environmental quality is not so good. In this paper, the design strategies directed by passive design ideas for a small experimental rural residential building located in Hangzhou city was introduced and researched in response to hot summer and cold winter climate. Through modeling solution undertaken by Ecotect software, the building performance was simulated and analyzed for the optimization of design factors, such as shape, roof angle, insulation system, shading devices, as well as day-lighting system. Based on the above study, a set of appropriate energy-saving technologies were provided for improving the new rural residences construction in Hangzhou, which should also be recommended to other projects constructed in the same climate region.

Research on the Development of Green Building Technology in Hot Summer and Cold Winter Area under the Background of Carbon Neutrality:A Case Study of Zhuzhou City

Carbon sequestration and emission reduction in the construction industry plays an important role in China’s goal of achieving carbon neutrality.Research in Zhuzhou city scored 42 since the assessment of the green building project situation as the research object,in hot summer and cold winter areas of analysis and evaluation on the development of green building technology,and then sums up the carbon neutral background the priority areas and tasks for the development of green building techniques,optimization of the construction industry into a new era under the background of green development to provide the reference.

夏热冬暖地区办公类建筑中BIN法应用的计算与分析

结合我国实际情况,依据BIN能耗分析负荷计算方法,以夏热冬暖地区某办公楼为例, 建立了建筑物全年空调负荷特性模型;通过计算在不同负荷率N下对应的运行时间百分数K,绘制了负荷分布特性曲线图,并在全年负荷计算的基础上绘制出了空调系统负荷小时数图,从而为此类建筑进行能耗分析与评价、合理选择冷源提供参考依据。

Thermal Performance of Building Roof with Infrared Reflective Coatings

This paper investigated the applicability and effects of infrared reflective coating on energy consumption of factory building in hot summer and warm winter zone.It first resorted to theoretical calculation,which demonstrated the beneficial effects of infrared reflective coating on reducing building energy consumption.Then it analyzed a field measurement done on two identical rooms respectively with ordinary coated roof and infrared reflective coated roof from November 2006 to October 2007,on a 24h basis.The measured data include exterior and interior roof surface temperature,indoor air temperature,and indoor globe temperature.The related weather data is from a weather station near the measured area.The continuous measurement has been accomplished in southern China,and the measured data indicate that roof surface temperature and heat gain are significantly decreased in summer while slight negative effects in winter are induced by adopting infrared reflective coating.Thus it is simple and applicable to reduce building energy consumption in this area by applying infrared reflective coating.Regress equation between reduced roof thermal property,such as surface temperature and heat gain,and reduction in absorbed solar radiation shows their highly linear relationship.Based on the measured data,it is estimated that the reduced power consumption is 3.45 kWh/m2·month in June.

Development of window opening models for residential building in hot summer and cold winter climate zone of China

This study monitors the open/closed states of the windows in 16 residential apartments in representative cities of the hot summer and cold winter zone of China,along with outdoor air temperature,outdoor relative humidity and outdoor PM2.5 concentration in 2017,to investigate the window opening/closing behavior.Three window opening models are developed.All the models are validated by modeling a typical residential apartment to compare the predicted indoor CO_(2)concentration with monitored data.It is found that the window opening probability is negatively correlated to both outdoor PM2.5 concentration and outdoor relative humidity,and the probability of window opening reaches the peak value when the outdoor air temperature is 23.7℃.In terms of season,the shortest window opening duration occurs in winter due to the cold outdoor air temperature and high outdoor PM2.5 concentration.Finally,by comparing the correlation between the measured date and simulation results of indoor CO_(2)concentration,this study provides an appropriate window opening model for reference.

夏热冬冷地区居住建筑辐射型反射隔热涂料节能设计方法研究

辐射型反射隔热涂料在夏热冬冷地区居住建筑中的应用案例越来越多,其节能设计方法备受关注。等效热阻法是目前反射隔热涂料热工设计的标准方法,但相关文献研究指出,涂覆于非透明材料上的隔热涂料应采用太阳光直接反射比作为隔热评价指标,不宜用等效热阻来评价。通过上海某6层住宅建筑探讨了夏热冬冷地区居住建筑外墙采用辐射型反射隔热涂料的节能效果及其传热系数、太阳辐射吸收系数和表面发射率之间的关系,对比分析了采用参数直接计算与等效热阻法计算能耗结果,结果表明:1)辐射型反射隔热涂料隔热机理与反射隔热涂料差异明显;2)辐射型反射隔热涂料节能效果不适宜采用等效热阻法进行节能效果评价;3)辐射型反射隔热涂料墙体冬季保温热阻设计应充分考虑其对墙体温度的负面影响。

夏热冬冷气候下太阳能住宅装配式设计实践

为推动我国村镇领域技术创新,建设绿色宜居村镇环境,针对夏热冬冷地区住宅的太阳能利用,从材料到构造,到建筑设计层面,完成与其配合的一体化技术设计策略研究及节能策略的应用探索。借助国际太阳能竞赛的契机,从前期设计的策略选取到后期项目的完成结果,总结实践经验,对比预期和实践的差距及原因。结果表明,前期平面、结构、材料、构造等都满足了对于太阳能利用技术的一体化设计,同时考虑了自然采光、隔热、遮阳等策略的应用,以减少能量损耗,取得了相应的效果,并对未达到预期效果的原因作出评判。

基于个人舒适系统杭州住宅冬季热舒适与能耗

为揭示该地区个人舒适系统(PCS)作用下的居民冬季热舒适特征和供暖能耗需求,以杭州市为对象,采用问卷调研和入户现场实测的方式得出冬季住宅开窗、遮阳、使用空调和PCS等典型热环境组合调节模式以及典型供暖模式和居民活动状态组合下的热舒适特征;在此基础上模拟得到冬季室内热舒适和供暖能耗特征。结果表明,冬季“无设备+静坐”、“空调+静坐”、“PCS+静坐”、“无设备+家务劳动”、“空调+家务劳动”、“PCS+家务劳动”等6种工况下的冬季中性温度分别是17.3、18.8、16.4、15.7、15.7、13.9℃,舒适温度区间分别是14.3~20.3℃、17.1~20.5℃、14.4~18.4℃、13.7~17.8℃、13.3~18.1℃、11.0~16.9℃。冬季室内热舒适水平受热环境调节模式影响较大,客厅在室舒适时间占比在43.74%~80.21%之间,卧室在室舒适时间占比均为70%以上。使用空调与PCS供暖时,典型建筑在冬初冬末的供暖能耗强度是1.28 kWh·m^(-2),在严冬的供暖能耗强度是13.06 kWh·m^(-2)。

基于街区小气候环境冬夏协同优化的城市绿地生态网络精准修复

越来越多城市绿地生态网络建设进入存量更新和结构性优化并存发展的阶段,生态安全优先基础上如何进一步提升城市绿地生态网络的多种生态系统服务功能是当前风景园林实践研究的重要议题。应对全球气候变化、极端天气多发导致的人居环境宜居性下降问题,目前基于气候适应的城市绿地生态网络规划关注促进自然通风以缓解夏季热岛效应,尚忽视了其冬季可能带来的负效应。从气候调节视角切入,探讨城市绿地生态网络在协同冬夏季小气候环境中的低效空间识别与精准修复技术方法。以江苏省昆山市密集城区的189个街区单元为研究对象,通过遥感反演的方法对其冬、夏季小气候环境进行分析,聚类获得7类小气候特征街区。之后,叠加现状绿地生态网络与计算流体力学模拟风环境结果,提取现状适于通风的生态廊道,从宽度、方向、类型等方面分析其潜在通风效能,耦合街区冬夏小气候环境特征,识别研判现状绿地生态网络在冬夏温湿环境调节上存在的低效问题,并提出冬夏协同的精准修复策略,为优化人居环境宜居性、提升城市绿地生态网络生态系统服务综合效能提供技术参考。

夏热冬冷地区办公建筑空调系统需求响应潜力的影响因素量化分析

近年来建筑空调系统的用电负荷在电网总负荷中的占比不断增大,如何高效推动建筑空调系统积极参与电力需求响应,对实现“削峰填谷”、提高电力系统灵活性、保障电网安全稳定运行具有重要意义。建筑空调系统需求响应潜力的科学评估是实现空调负荷柔性调控的基础,难点在于多因素耦合影响,量化评估难。以夏热冬冷地区某办公建筑为例,基于EnergyPlus软件模拟,通过控制变量法对影响建筑空调系统需求响应潜力的4种因素(室外天气、建筑围护结构性能、空调系统性能、需求响应策略)进行敏感性分析。结果表明,建筑围护结构性能变化对空调系统需求响应潜力影响较小,而其他3种因素影响较大。其中,当夏季室外空气焓值由70~75 kJ/kg上升至85~90 kJ/kg时,空调系统参与需求响应的峰值负荷削减量(即需求响应潜力)由13.01 W/m^(2)提升至17.54 W/m^(2)(增大35%);当多联机系统COP由4.0降低至2.5时,需求响应潜力由19.51 W/m^(2)提升至31.21 W/m^(2)(增大60%);当水冷式空调系统COP由6.0降低至3.0时,需求响应潜力由11.60 W/m^(2)提升至23.20 W/m^(2)(增大100%);当需求响应策略由室温设定值上升2℃变为上升4℃时,需求响应潜力由10.74 W/m^(2)提升至17.28 W/m^(2)(增大61%)。

夏热冬冷地区动态传热保温设计室外典型气象参数确定方法

GB50176-2016《民用建筑热工设计规范》中围护结构外墙保温设计采用稳态方法,但夏热冬冷地区由于特有的建筑运行模式,使外墙传热方向发生逆转,故稳态方法难以满足冬季室内热环境水平提升的实际需求。提出一种基于动态传热的冬季外墙保温设计室外计算温度确定方法,探究室外干球温度和太阳辐射逐时波动的最不利组合,将保温设计的目标由“日”提升到“时”。基于典型城市2007-2017年逐时气象数据,以外墙内表面温度的累计不保证天数作为热工设计指标,将累计不保证天数恰好不为0(指各朝向外墙内表面温度低于室内基本热舒适条件下所能允许温差的天数)时作为典型日挑选的依据,并将典型日出现频率最高的日期作为室外计算温度选取的依据,获得冬季保温设计典型日,并获得了典型日计算时长的影响。可为夏热冬冷地区围护结构外墙保温设计室外计算参数的挑选提供理论支撑。

夏热冬冷地区住宅浴室热湿环境与洗浴行为研究

对上海地区住宅浴室热湿环境进行了实地测量,分析了浴室热湿环境特征,并通过网络问卷调研了典型人群的洗浴行为。结果表明:浴室热湿环境受洗浴行为影响明显,淋浴开始后空气温度迅速升高,相对湿度接近饱和状态,淋浴结束后相对湿度需要较长时间才能恢复至初始状态,与常规居家场景相比,洗浴过程中的浴室热湿环境偏离常规热舒适区;夏热冬冷地区居民洗浴行为受季节影响明显,淋浴水温冬季偏暖(43.3℃左右)、夏季偏凉(一般36~40℃);洗浴频次以1天1次或2天1次为主;洗浴时长夏季多为5~10 min、冬季多为10~20 min。本文还探讨了浴室环境改善措施和浴室热舒适的特殊性。

施用生物炭和秸秆还田对农田温室气体排放及增温潜势的影响

【目的】农业生态系统增温潜势是影响全球气候变化的重要部分。本研究通过田间试验明确施用生物炭和秸秆还田对农田增温潜势的影响,以期为减缓气候变化和农业废弃物资源化利用提供理论依据。【方法】在山东省桓台县农业生态系统试验站的冬小麦-夏玉米轮作农田中开展了3年田间定位试验,试验共设置4个处理:①对照(CK);②施用生物炭9.0t·hm^(-2)·a^(-1)(C);③全量秸秆还田(S);④秸秆还田配施9.0 t·hm^(-2)·a^(-1)生物炭(CS)。4个处理均施等量的氮磷钾化肥,其中氮肥为尿素,用量为200 kg·hm^(-2)·a^(-1),磷肥为过磷酸钙,用量为55 kg·hm^(-2)·a^(-1),钾肥为硫酸钾,用量为40 kg·hm^(-2)·a^(-1)。采用静态暗箱-气相色谱法测定各处理温室气体(CO_(2)、N_(2)O和CH_4)的排放通量并计算净全球增温潜势(NGWP)和温室气体排放强度(GHGI),分析连续施用生物炭和秸秆还田对农田温室气体排放及增温潜势的影响。【结果】(1)综合3年的温室气体排放情况,与CK处理相比,S和CS处理的年平均生态呼吸排放量(Re)分别增加了47.8%和67.9%(P<0.05);C处理的年平均N_(2)O累积排放量降低了20.3%(P<0.05),而S和CS处理的N_(2)O年平均累积排放量分别增加了23.6%和41.4%(P<0.05)。(2)与CK处理相比,C、S和CS处理的土壤有机碳年平均变化量(ΔSOC)均有显著增加,其中CS处理增幅最大,增加了150.6%(P<0.05)。与第1年相比,C、S和CS处理第3年的ΔSOC均有显著增加(P<0.05),分别增加了21.7%、20.8%和17.8%。各处理的NGWP和GHGI均存在显著差异,与CK相比,C、S和CS处理的年平均NGWP分别降低了163.5%、171.7%和273.0%(P<0.05),与第1年相比,C、S和CS处理第3年的NGWP均有显著降低(P<0.05),分别降低了73.4%、58.8%和54.7%。与CK相比,C、S和CS处理的年平均GHGI分别降低了236.2%、253.3%和388.9%(P<0.05),C、S和CS处理第3年的GHGI较第1年分别降低了126.3%、98.2%和108.6%(P<0.05)。就产量而言,C、S和CS处理的作物产量保持相对稳定,有轻微增长,但与CK相比无显著差异。【结论】与单施化肥相比,在施化肥的基础上添加生物炭、秸秆还田、秸秆还田配施生物炭的措施均能够在不影响作物产量的前提下抑制增温潜势,其中秸秆还田配施生物炭能够最大程度地降低农田增温潜势,因此秸秆还田配施生物炭是增加农田固碳、缓解气候变化的一项有效措施。

夏热冬暖地区办公建筑外遮阳百叶智能控制对比分析

随着建筑节能工作深入,建筑智能遮阳技术迅速发展,外遮阳智能控制系统成为有效降低建筑能耗、提高能源利用效率的新兴节能技术。通过建筑外遮阳百叶智能控制系统的对比设计,采用EnergyPlus的EMS模块进行模拟,比较东向百叶外遮阳不同智能控制方式对室内能耗的影响,对百叶最优倾角常开、入射角控制、冷负荷控制、综合控制进行能耗分析。研究结果发现:3种百叶控制方式与百叶最优倾角常开状态对比均有一定的节能效果,仅有入射角控制这一方式的总能耗最低,综合控制次之,仅有冷负荷控制的方式能耗最高。研究结果为建筑设计者提供了关于东向百叶外遮阳智能控制系统设置的参考,通过优化入射角控制设置降低能耗、提高建筑舒适性。

夏热冬冷地区大型交通建筑条形天窗天然采光优化设计研究

随着我国城镇化不断深入,大型交通建筑的建设需求日益增长。因其立面有限而平面巨大,故主要依赖天窗实现大进深平面的天然采光。因结构构造简化需求,常忽视日照条件差异,照搬相似的一列多排式条形平天窗分布形式,且忽略各类遮阳措施的设置,常易因局部采光不足或眩光导致整体采光不均。夏热冬冷地区作为冬夏两季太阳高度角差异较大的典型地域代表,其对两季天窗采光的优化需求常互相掣肘,该地区大型交通建筑采光与遮阳综合控制故而更为复杂,对其条形天窗与遮阳设计也具有更高的要求。针对上述关键科学问题,选取杭州市某大型铁路客站典型案例开展采光物理实测,总结出该气候区条形天窗分布下此类建筑实际采光问题,并基于大型交通建筑典型模型,围绕天窗与遮阳形式关键变量,通过Rhino平台的Ladybug+Honeybee工具完成了全年动态光环境模拟。结果表明:在夏热冬冷地区,大型铁路客站即使采用常见的条形天窗采光方式,仍可能存在局部照度不足和整体采光均匀度较低的问题,候车厅中央天窗正下方区域常因出现太阳光直射过量导致较大的眩光风险,其照度远大于仍有采光不足风险的天窗外围下方区域。为改善这一现象,应在适度窗地比范围内首先保证适中偏高的天窗宽度,并匹配适中偏大的天窗长度与数量,而尽量避免所有较小的天窗宽度、长度与数量。当天窗窗地比较小时,可采取较大的横向遮阳高度、适中的竖向遮阳角度(正南向)与偏少的竖向遮阳数量;而天窗窗地比较大时则相反,以保证在尽量不降低采光均匀度的前提下最大化采光强度,以实现整体均衡的光环境表现。

基于GIOWA算子的夏热冬冷地区装配式钢结构墙体保温优化方案比选

随着建筑节能技术的不断进步,复合墙体保温系统也不断创新,复合墙体保温系统从大的方面来看,可以划分为外墙外保温系统,外墙内保温系统等,为响应国家大力发展建筑业的呼吁,其在实际应用中的适用性需要进一步研究,将优化后的装配式钢结构节能方案与未做保温方案进行适用性综合评价,结果表示对装配式钢结构复合墙体进行节能优化设计很有必要。选择GIOWA算子作为适用性评价建模方法,选定环境影响性、安全防火性、节能性、经济性、市场接受程度和墙体厚度作为外墙适用性综合评价因素,以我国夏热冬冷地区4个典型城市(重庆,徐州,南昌,遵义)为研究对象,进行方案比选,研究其在不同城市的方案适用性。结果表明:重庆地区想要选择降低能耗并且兼具经济性的方案为挤塑聚苯板作为保温材料的方案三,徐州、南昌、遵义地区想要选择降低能耗并且兼具经济性的方案为玻化微珠无机保温板作为保温材料的方案四。