This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The ...This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The findings revealed the formation ofγ-TiH andδ-TiH_(2) hydrides in the alloy after hydrogen charging.Prolonging hydrogen charging resulted in more significant degradation of the alloy microstructure,leading to deteriorated protectiveness of the surface film.This trend was further confirmed by the electrochemical measurements,which showed that the corrosion resistance of the alloy progressively worsened as the hydrogen charging time was increased.Consequently,this work provides valuable insights into the mechanisms underlying the corrosion of Ti-6Al-4V alloy under hydrogen charging conditions.展开更多
At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fat...At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks.However,there are few studies on the effects of these key factors on fretting wear.In the paper,shot-peening(SP)and ultrasonic surface rolling process(USRP)were performed on Ti-6Al-4V plate specimens.The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer.Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester.The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments.The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation,and the mechanism of improving fretting fatigue life by surface strengthening process was further explained.After USRP treatment,the surface roughness of Ti-6Al-4V is significantly improved.In addition,the microhardness of the specimen after SP reaches the maximum at 80μm from the surface,which is about 123%higher than that of the AsR specimen.After USRP,it reaches the maximum at 150μm from the surface,which is about 128%higher than that of AsR specimen.It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction,and the residual stress reaches the maximum on the sub surface.The USRP specimen reaches the maximum value at 0.18 mm,about−550 MPa,while the SP specimen reaches the maximum value at 0.1 mm,about−380 MPa.The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP.The surface integrity of specimens after USRP is the best,which has deeper residual compressive stress layer and more refined grain.In this paper,a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.展开更多
The deformaton behavior of Ti - 6Al - 4V alloy under hot - working condition has been studied by compression testing in the temperature range 750 - 950℃ and strain rate range 0.05 - 15s -1. The flow stress decrease...The deformaton behavior of Ti - 6Al - 4V alloy under hot - working condition has been studied by compression testing in the temperature range 750 - 950℃ and strain rate range 0.05 - 15s -1. The flow stress decreases with the increase of temperature and with the decrease of strain rate. After a steep initial strain hardening, a flow softening occurs. This softening is mainly ascribed to the temperature rise and dynamic recmptallisation.By a simple extension, a classical sinushyperbolic constitutive equation can be used to describe the flow behavior of Ti - 6Al - 4V alloy. flow stress is described as a function of strain, strain rate and temperature. The parameters Q, n andaare the same at differ- ent deformation conditions, and A is a funciton of strain.展开更多
The effects of heat treatment on the microstructure and mechanical properties of laser solid forming (LSF) Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging...The effects of heat treatment on the microstructure and mechanical properties of laser solid forming (LSF) Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging treatment were analyzed. The results show that the microstructure of LSFed samples consists of Widmanstatten α laths and a little acicular in columnar prior β grains with an average grain width of 300 μm, which grow epitaxiaUy from the substrate along the deposition direction (27). Solution treatment had an important effect on the width, aspect ratio, and volmne fraction of primary and secondary a laths, and aging treatment mainly affects the aspect ratio and volume fraction of primary α laths and the width and volume fraction of secondary a laths. Globular a phase was first observed in LSFed samples when the samples were heat treated with solution treatment (950℃, 8 h/air cooling (AC)) or with solution treatment (950℃, 1 h/AC) and aging treatment (550℃, above 8 h/AC), respectively. The coarsening and globularization mechanisms of a phase in LSFed Ti-6Al-4V alloy during heat treatment were presented. To obtain good integrated mechanical properties for LSFed Ti-6Al-4V alloys, an optimized heat treatment regimen was suggested.展开更多
A constitutive model is critical for the prediction accuracy of a metal cutting simulation. The highest strain rate involved in the cutting process can be in the range of 104-106 s 1. Flow stresses at high strain rate...A constitutive model is critical for the prediction accuracy of a metal cutting simulation. The highest strain rate involved in the cutting process can be in the range of 104-106 s 1. Flow stresses at high strain rates are close to that of cutting are difficult to test via experiments. Split Hopkinson compression bar (SHPB) technology is used to study the deformation behavior of Ti-6Al-4V alloy at strain rates of 10 -4-10 4s- 1. The Johnson Cook (JC) model was applied to characterize the flow stresses of the SHPB tests at various conditions. The parameters of the JC model are optimized by using a genetic algorithm technology. The JC plastic model and the energy density-based ductile failure criteria are adopted in the proposed SHPB finite element simulation model. The simulated flow stresses and the failure characteristics, such as the cracks along the adiabatic shear bands agree well with the experimental results. Afterwards, the SHPB simulation is used to simulate higher strain rate(approximately 3 × 10 4 s -1) conditions by minimizing the size of the specimen. The JC model parameters covering higher strain rate conditions which are close to the deformation condition in cutting were calculated based on the flow stresses obtained by using the SHPB tests (10 -4 - 10 4 s- 1) and simulation (up to 3 × 10 4 s - 1). The cutting simulation using the constitutive parameters is validated by the measured forces and chip morphology. The constitutive model and parameters for high strain rate conditions that are identical to those of cutting were obtained based on the SHPB tests and simulation.展开更多
Ti-6Al-4V alloy is extensively used in the manufacture of components in aviation.In the current study,the laser welding process is adopted to joint the Ti-6Al-4V alloy plate which has the thick of 8 mm.A three-dimensi...Ti-6Al-4V alloy is extensively used in the manufacture of components in aviation.In the current study,the laser welding process is adopted to joint the Ti-6Al-4V alloy plate which has the thick of 8 mm.A three-dimensional finite element model is established to simulate the temperature distribution of laser welding process.The thermal cycle curves are produced on the strength of the simulation results.Meanwhile,the microstructure characteristics of the welded joint are investigated combined with simulation results.The results show that weld zone,heat affected zone and based metal experience similar thermal cycles process and the cooling rate has an important influence on the formation of microstructure.Moreover,the simulation results are well matched with experiment results.展开更多
Compound ceramic coatings on Ti-6Al-4V alloy were prepared for different time by pulsed bi-polar micro-plasma oxidation (MPO) in NaAlO2 solution. The phase composition was studied by XRD. And the electrochemical imped...Compound ceramic coatings on Ti-6Al-4V alloy were prepared for different time by pulsed bi-polar micro-plasma oxidation (MPO) in NaAlO2 solution. The phase composition was studied by XRD. And the electrochemical impedance spectra (EIS) of the coatings were measured to study the structure of the coatings, combined with the surface morphology. Using the proper EIS interpreting software, the "equivalent circuit" of the coatings was established, and meanwhile fitting values of equivalent element were obtained. The results show that the coating is composed of Al2 TiO5, α-Al2O3 and rutile TiO2, of which Al2 TiO5 is the main crystalline. Increasing the MPO time, the contents of Al2TiO5, rutile TiO2 and α-Al2O3 in the surface of the coating increase. And the EIS analysis and the surface morphology of the coatings illustrates the double-layer structure of the coatings, and the outer layer is loosen and the inner layer is compact. With the increase of the oxidizing time, the surface coarse degree of the coatings and the porosity of the outer layer of the coating are increased while the compactness of the inner layer of the coating is improved.展开更多
Laser direct deposition (LDD) of metallic components is an advanced technology of combining CAD/CAM (computer aided design/computer aided manufacturing), high power laser, and rapid prototyping. This technology us...Laser direct deposition (LDD) of metallic components is an advanced technology of combining CAD/CAM (computer aided design/computer aided manufacturing), high power laser, and rapid prototyping. This technology uses laser beam to melt the powders fed coaxiaUy into the molten pool by the laser beam to fabricate fuUy dense metallic components. The present article mainly studies the LDD of Ti-6Al-4V alloy, which can be used to fabricate aircraft components. The mechanical properties of the Ti-6Al-4V alloy, fabricated by LDD, are obtained using the tension test, and the oxygen content of used powders and deposited specimens are measured. In the present article, it can be seen that the mechanical properties obtained using this method are higher than the ones obtained by casting, and equal to those got by wrought anneal. One aircraft part has been made using the LDD process. Because of this aircraft part, with sophisticated shape, the effect of the laser scanning track on the internal soundness of the deposited part was discussed.展开更多
Laser shock peening(LSP)is an attractive post-processing method to tailor surface microstructure and enhance mechanical performances of additive manufactured(AM)components.The effects of multiple LSP treatments on the...Laser shock peening(LSP)is an attractive post-processing method to tailor surface microstructure and enhance mechanical performances of additive manufactured(AM)components.The effects of multiple LSP treatments on the microstructure and mechanical properties of Ti-6Al-4V part produced by electron beam melting(EBM),as a mature AM process,were studied in this work.Microstructure,surface topography,residual stress,and tensile performance of EBM-manufactured Ti-6Al-4V specimens were systematically analyzed subjected to different LSP treatments.The distribution of porosities in EBM sample was assessed via X-ray computed tomography.The results showed that EBM samples with two LSP treatments possessed a lower porosity value of 0.05%compared to the value of 0.08%for the untreated samples.The strength of EBM samples with two LSP treatments was remarkably raised by 12%as compared with the as-built samples.The grains ofαphase were refined in near-surface layer,and a dramatic increase in the depth and magnitude of compressive residual stress(CRS)was achieved in EBM sample with multiple LSP treatments.The grain refinement ofαphase and CRS with larger depth were responsible for the strength enhancement of EBM samples with two LSP treatments.展开更多
The surface modification of materials such as Ti-6Al-4V is necessary to improve their wear resistant properties for use in tribological applications. In this paper it is shown that a laser with low power and tungsten ...The surface modification of materials such as Ti-6Al-4V is necessary to improve their wear resistant properties for use in tribological applications. In this paper it is shown that a laser with low power and tungsten inert gas (TIG) can be combined together for surface modification of Ti-6Al-4V alloy, and when performed in a controlled atmosphere of pure nitrogen or a mixture of nitrogen and argon, can produce a wear-resistant surface alloy. Compared with laser processing, a cheaper surface modification process has been developed involving a shorter processing time, which is free of stringent requirements such as a vacuum system.展开更多
Ti-6AI-4V, among the Ti alloys, is the most widely used. In the present work, the behavior of Ti-6AI-4V alloy has been investigated by the uniaxial hot isothermal compression tests and a series of dilatometric experim...Ti-6AI-4V, among the Ti alloys, is the most widely used. In the present work, the behavior of Ti-6AI-4V alloy has been investigated by the uniaxial hot isothermal compression tests and a series of dilatometric experiments were also carried out to determine the transformation temperatures at different cooling rates. Specimens for hot compression tests were homogenized at 1050℃ for 10 min and then quickly cooled to different straining temperatures from 1050 to 850℃. Cooling rates were chosen fast enough to prevent high temperature transformation during cooling. Compression tests were conducted at temperatures from 1050 to 850℃ in steps of 50℃ at constant true strain rates of 10-3 or 10-2 s-1. The apparent activation energy for compression in two-phase region was calculated 420 kJ·mol-1. Partial globularization of a phase was observed in the specimen deformed at low strain rates and at temperatures near the transformation zone and annealed after deformation.展开更多
This work aims to investigate the effects of hydrogen content(in the range of 0%-0.5%,mass fraction)and stress state (tension and compression)on the room-temperature mechanical properties of Ti-6Al-4V alloy through me...This work aims to investigate the effects of hydrogen content(in the range of 0%-0.5%,mass fraction)and stress state (tension and compression)on the room-temperature mechanical properties of Ti-6Al-4V alloy through mechanical properties tests. The effects of hydrogen content on microstructure evolution of Ti-6Al-4V alloy is also examined by optical microscopy,X-ray diffractometry,transmission electron microscopy and scanning electron microscopy.The results show that hydrogen content and stress state have important effects on the room-temperature mechanical properties of Ti-6Al-4V alloy.Tensile strength and ultimate elongation decrease with increasing the hydrogen content,while compressive strength and ultimate reduction are improved after hydrogenation.The reason is that the intergranular deformation dominates at the state of tension.Hydrogen atoms in solid solution and hydrides at grain boundaries increase with increasing the hydrogen content and they can promote the initiation and propagation of cracks along grain boundaries.While the intragranular deformation dominates at the state of compression.The plastic beta phase and hydrides increase with increasing the hydrogen content and they improve the ultimate reduction and compressive strength.展开更多
The cast Ti-6Al-4V alloy bars with different section sizes were fabricated by investment casting at counter-gravity condition with the mold temperatures of 300 °C and 650 °C, respectively. The microstructure...The cast Ti-6Al-4V alloy bars with different section sizes were fabricated by investment casting at counter-gravity condition with the mold temperatures of 300 °C and 650 °C, respectively. The microstructure of the alloy was observed by means of OM and SEM, and the effect of mold temperature and casting dimension on tensile properties was studied. Results show that equiaxed grains are obtained regardless of the casting dimension. β grain size tends to increase with an increase in mold temperature. Hot isostatic pressing of the alloy was carried out for tensile properties' comparison. Room temperature tensile test results show that Ti-6Al-4V alloy produced via counter-gravity casting has good balance of strength and ductility after hot isostatic pressing(HIP). The alloy shows higher ductility due to the elimination of porosity. In both cast and HIP status, the tensile strength is inclined to decrease with an increase in mold temperature, while the ductility is prone to slightly increase. Both the strength and ductility tend to decrease with an increase in the casting dimension.展开更多
Hot crack is one of common defects in castings, which often results in failure of castings. This work studies the formation of hot crack during cold crucible continuous casting by means of experiments and theoretical ...Hot crack is one of common defects in castings, which often results in failure of castings. This work studies the formation of hot crack during cold crucible continuous casting by means of experiments and theoretical analysis. The results show that hot crack occurs on the surface and in the circumference of ingots, where the solidified shell and the solidification front meet each other. The tendency of hot cracking decreases with the increase of withdrawal velocities in some extent. The hot crack is caused mainly by the friction force between the shell and the crucible inner wall, and it takes place when the stress resulting from friction exceeds the tensile strength of the shell. The factors of μ_m, η_t, η_s and η_m, affecting hot cracks are analyzed and verified. In order to decrease the tendency of hot cracks, technical parameters should be optimized by decreasing μ_m, η_t, η_s and η_m.展开更多
The dynamic corrosion behaviors of Ti-6Al-4V alloy in acid artificial saliva containing fluoride ion were traced using electrochemical techniques,optical microscope,scanning electron microscopy,energy dispersive spect...The dynamic corrosion behaviors of Ti-6Al-4V alloy in acid artificial saliva containing fluoride ion were traced using electrochemical techniques,optical microscope,scanning electron microscopy,energy dispersive spectrometer and roughness tester.The experimental results indicate that a negative shift of corrosion potential as well as a continuous decrease in impedance for the alloy exists with increasing immersion time,and the degradation rate of the alloy presents the trend of first increase then decrease following the dissolution of passivation film and the formation of corrosion products.The accumulated fluoride ion on the alloy surface accelerates the fracture of passivation film,and the occurrence and development of corrosion of alloy are mainly located at the sites where the formation and shedding of white particles are composed of fluoride compounds,resulting in the decrease of corrosion resisting property of the alloy.A possible model is proposed to elaborate the dynamic corrosion behavior of the alloy.展开更多
The aluminide coating process of Ti-6Al-4V alloys with different fillers(100wt.% Al_2O_3,50wt% Y_2O_3+50wt.% Al_2O_3 and 100wt.% Y_2O_3) for improvement of the oxidation resistance were investigated.The results show t...The aluminide coating process of Ti-6Al-4V alloys with different fillers(100wt.% Al_2O_3,50wt% Y_2O_3+50wt.% Al_2O_3 and 100wt.% Y_2O_3) for improvement of the oxidation resistance were investigated.The results show that the filler does not only participate in the aluminizing process,but also has much effect on the coating composition.The XRD analysis reveals that the aluminide coating with filler Al_2O_3 is predominant with TiAl_3 and TiAl phases;while the aluminide coatings with filler Y_2O_3+Al_2O_3 are predominant with Ti_3Al phase.The oxidation kinetics shows that different fillers affect greatly the oxidation resistance of aluminide coating,and the oxidation resistance of aluminized specimens with pack aluminizing filler Al_2O_3 are about 5-8 times than that of the aluminized specimens with other pack aluminizing fillers.展开更多
The microstrueture and various hydrides precipitated in Ti-6A1-4V alloys containing hydrogen 0.16,0.58,0.87,1.49 wt-%,respectively,have been studied by means of TEM and X-ray diffraction.The Ti_3Al phase may precipita...The microstrueture and various hydrides precipitated in Ti-6A1-4V alloys containing hydrogen 0.16,0.58,0.87,1.49 wt-%,respectively,have been studied by means of TEM and X-ray diffraction.The Ti_3Al phase may precipitate when H over 0.58 wt-%.In the same time,the morphology of hydrides gradually changed from rugged sheets to narrow laths as H contents increased.The microstructure of highly H-doped alloys is obviously fine.A mas- sive hydride and the hydride with tetragonal lattice were observed in the specimen containing 1.49 wt-%H.The twin hydrides were found in the alloys with different H contents and the electron diffraction patterns of the twin hydrides can be served as a simple criterion for distin- guishing the cubic and tetragonal structures.展开更多
Numerical investigations of the 'banding' microstructure formation during solidification of Ti-6Al-4 V alloy in the centrifugal casting are conducted using a multi-scale model, which combines the finite difference m...Numerical investigations of the 'banding' microstructure formation during solidification of Ti-6Al-4 V alloy in the centrifugal casting are conducted using a multi-scale model, which combines the finite difference method (FDM) at the macroscale with a cellular automaton (CA) model at the microscale. The macro model is used to simulate the fluid flow and heat transfer throughout the casting. The micro model is used to predict the nucleation and growth of microstructures. With the proposed model, numerical simulations are performed to study the influences of the nucleation density, mould rotation speed, and casting size upon the 'banding' microstructure formation. It is noted that changing the nucleation density has a minor effect on the microstructure formation. The rotation speed promotes the formation of 'banding' microstructure, which is more noticeable for larger size castings. The 'major mechanism responsible for this 'banding' phenomenon is the spatial variation in cooling rates created by centrifugal force.展开更多
The effects of various hydrogen contents on the flow stress(σ),strain rate sensitivity expo- nent(m)and the tensile elongation(δ)of Ti-6Al-4V alloy were studied.The microstructure of the alloy was also investigated....The effects of various hydrogen contents on the flow stress(σ),strain rate sensitivity expo- nent(m)and the tensile elongation(δ)of Ti-6Al-4V alloy were studied.The microstructure of the alloy was also investigated.The results indicate that,a suitable amount of hydrogen in the alloy can reduce the flow stress in the temperature range 800—860℃. Consequently,the superplastic temperature can be decreased and the ductility improved.展开更多
The effect of triple annealing on stress relaxation of Ti-6Al-4V alloy as well as the microstructure after stress relaxation werestudied. The results showed that triple annealing treatment enhanced the resistance of s...The effect of triple annealing on stress relaxation of Ti-6Al-4V alloy as well as the microstructure after stress relaxation werestudied. The results showed that triple annealing treatment enhanced the resistance of stress relaxation performance, andwhen the temperature was rising, this effect became notable. The stress relaxation deformation mechanism is of dislocationcreep at 400℃ and recovery creep at 600℃.展开更多
基金Supported by National Natural Science Foundation of China(Grant Nos.52001142,52005228,51801218,51911530211,51905110)Young Scientists Sponsorship Program by CAST(Grant No.2022QNRC001).
文摘This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The findings revealed the formation ofγ-TiH andδ-TiH_(2) hydrides in the alloy after hydrogen charging.Prolonging hydrogen charging resulted in more significant degradation of the alloy microstructure,leading to deteriorated protectiveness of the surface film.This trend was further confirmed by the electrochemical measurements,which showed that the corrosion resistance of the alloy progressively worsened as the hydrogen charging time was increased.Consequently,this work provides valuable insights into the mechanisms underlying the corrosion of Ti-6Al-4V alloy under hydrogen charging conditions.
基金Supported by National Key Research and Development Project(Grant No.2018YFC1902400)Natural Science Foundation of Shanghai(Grant No.20ZR1415300).
文摘At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks.However,there are few studies on the effects of these key factors on fretting wear.In the paper,shot-peening(SP)and ultrasonic surface rolling process(USRP)were performed on Ti-6Al-4V plate specimens.The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer.Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester.The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments.The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation,and the mechanism of improving fretting fatigue life by surface strengthening process was further explained.After USRP treatment,the surface roughness of Ti-6Al-4V is significantly improved.In addition,the microhardness of the specimen after SP reaches the maximum at 80μm from the surface,which is about 123%higher than that of the AsR specimen.After USRP,it reaches the maximum at 150μm from the surface,which is about 128%higher than that of AsR specimen.It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction,and the residual stress reaches the maximum on the sub surface.The USRP specimen reaches the maximum value at 0.18 mm,about−550 MPa,while the SP specimen reaches the maximum value at 0.1 mm,about−380 MPa.The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP.The surface integrity of specimens after USRP is the best,which has deeper residual compressive stress layer and more refined grain.In this paper,a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.
文摘The deformaton behavior of Ti - 6Al - 4V alloy under hot - working condition has been studied by compression testing in the temperature range 750 - 950℃ and strain rate range 0.05 - 15s -1. The flow stress decreases with the increase of temperature and with the decrease of strain rate. After a steep initial strain hardening, a flow softening occurs. This softening is mainly ascribed to the temperature rise and dynamic recmptallisation.By a simple extension, a classical sinushyperbolic constitutive equation can be used to describe the flow behavior of Ti - 6Al - 4V alloy. flow stress is described as a function of strain, strain rate and temperature. The parameters Q, n andaare the same at differ- ent deformation conditions, and A is a funciton of strain.
基金supported by the Program for New Century Excellent Talents in Universities of China (No.NCET-06-0879)the National Natural Science Foundation of China (No.50331010)+2 种基金the Northwestern Polytechnical University Foundation of Fundamental Research (No.NPU-FFR-JC200808)the National Basic Research Program of China (No.2007CB613800)the Program of Introducing Talents of Discipline to Universities,China (No.08040)
文摘The effects of heat treatment on the microstructure and mechanical properties of laser solid forming (LSF) Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging treatment were analyzed. The results show that the microstructure of LSFed samples consists of Widmanstatten α laths and a little acicular in columnar prior β grains with an average grain width of 300 μm, which grow epitaxiaUy from the substrate along the deposition direction (27). Solution treatment had an important effect on the width, aspect ratio, and volmne fraction of primary and secondary a laths, and aging treatment mainly affects the aspect ratio and volume fraction of primary α laths and the width and volume fraction of secondary a laths. Globular a phase was first observed in LSFed samples when the samples were heat treated with solution treatment (950℃, 8 h/air cooling (AC)) or with solution treatment (950℃, 1 h/AC) and aging treatment (550℃, above 8 h/AC), respectively. The coarsening and globularization mechanisms of a phase in LSFed Ti-6Al-4V alloy during heat treatment were presented. To obtain good integrated mechanical properties for LSFed Ti-6Al-4V alloys, an optimized heat treatment regimen was suggested.
基金Supported by National Natural Science Foundation of China(Grant Nos.51205284,51575384)
文摘A constitutive model is critical for the prediction accuracy of a metal cutting simulation. The highest strain rate involved in the cutting process can be in the range of 104-106 s 1. Flow stresses at high strain rates are close to that of cutting are difficult to test via experiments. Split Hopkinson compression bar (SHPB) technology is used to study the deformation behavior of Ti-6Al-4V alloy at strain rates of 10 -4-10 4s- 1. The Johnson Cook (JC) model was applied to characterize the flow stresses of the SHPB tests at various conditions. The parameters of the JC model are optimized by using a genetic algorithm technology. The JC plastic model and the energy density-based ductile failure criteria are adopted in the proposed SHPB finite element simulation model. The simulated flow stresses and the failure characteristics, such as the cracks along the adiabatic shear bands agree well with the experimental results. Afterwards, the SHPB simulation is used to simulate higher strain rate(approximately 3 × 10 4 s -1) conditions by minimizing the size of the specimen. The JC model parameters covering higher strain rate conditions which are close to the deformation condition in cutting were calculated based on the flow stresses obtained by using the SHPB tests (10 -4 - 10 4 s- 1) and simulation (up to 3 × 10 4 s - 1). The cutting simulation using the constitutive parameters is validated by the measured forces and chip morphology. The constitutive model and parameters for high strain rate conditions that are identical to those of cutting were obtained based on the SHPB tests and simulation.
文摘Ti-6Al-4V alloy is extensively used in the manufacture of components in aviation.In the current study,the laser welding process is adopted to joint the Ti-6Al-4V alloy plate which has the thick of 8 mm.A three-dimensional finite element model is established to simulate the temperature distribution of laser welding process.The thermal cycle curves are produced on the strength of the simulation results.Meanwhile,the microstructure characteristics of the welded joint are investigated combined with simulation results.The results show that weld zone,heat affected zone and based metal experience similar thermal cycles process and the cooling rate has an important influence on the formation of microstructure.Moreover,the simulation results are well matched with experiment results.
基金Project (50171026) supported by the National Natural Science Foundation of China
文摘Compound ceramic coatings on Ti-6Al-4V alloy were prepared for different time by pulsed bi-polar micro-plasma oxidation (MPO) in NaAlO2 solution. The phase composition was studied by XRD. And the electrochemical impedance spectra (EIS) of the coatings were measured to study the structure of the coatings, combined with the surface morphology. Using the proper EIS interpreting software, the "equivalent circuit" of the coatings was established, and meanwhile fitting values of equivalent element were obtained. The results show that the coating is composed of Al2 TiO5, α-Al2O3 and rutile TiO2, of which Al2 TiO5 is the main crystalline. Increasing the MPO time, the contents of Al2TiO5, rutile TiO2 and α-Al2O3 in the surface of the coating increase. And the EIS analysis and the surface morphology of the coatings illustrates the double-layer structure of the coatings, and the outer layer is loosen and the inner layer is compact. With the increase of the oxidizing time, the surface coarse degree of the coatings and the porosity of the outer layer of the coating are increased while the compactness of the inner layer of the coating is improved.
基金This work was supported by the National Natural Science Foundation of China (No. 50331010)
文摘Laser direct deposition (LDD) of metallic components is an advanced technology of combining CAD/CAM (computer aided design/computer aided manufacturing), high power laser, and rapid prototyping. This technology uses laser beam to melt the powders fed coaxiaUy into the molten pool by the laser beam to fabricate fuUy dense metallic components. The present article mainly studies the LDD of Ti-6Al-4V alloy, which can be used to fabricate aircraft components. The mechanical properties of the Ti-6Al-4V alloy, fabricated by LDD, are obtained using the tension test, and the oxygen content of used powders and deposited specimens are measured. In the present article, it can be seen that the mechanical properties obtained using this method are higher than the ones obtained by casting, and equal to those got by wrought anneal. One aircraft part has been made using the LDD process. Because of this aircraft part, with sophisticated shape, the effect of the laser scanning track on the internal soundness of the deposited part was discussed.
基金financially supported by the Shanghai Science and Technology Committee Innovation Grant(Nos.17JC1400600 and 17JC1400603)the Distinguished Professor Program of Shanghai University of Engineering Science。
文摘Laser shock peening(LSP)is an attractive post-processing method to tailor surface microstructure and enhance mechanical performances of additive manufactured(AM)components.The effects of multiple LSP treatments on the microstructure and mechanical properties of Ti-6Al-4V part produced by electron beam melting(EBM),as a mature AM process,were studied in this work.Microstructure,surface topography,residual stress,and tensile performance of EBM-manufactured Ti-6Al-4V specimens were systematically analyzed subjected to different LSP treatments.The distribution of porosities in EBM sample was assessed via X-ray computed tomography.The results showed that EBM samples with two LSP treatments possessed a lower porosity value of 0.05%compared to the value of 0.08%for the untreated samples.The strength of EBM samples with two LSP treatments was remarkably raised by 12%as compared with the as-built samples.The grains ofαphase were refined in near-surface layer,and a dramatic increase in the depth and magnitude of compressive residual stress(CRS)was achieved in EBM sample with multiple LSP treatments.The grain refinement ofαphase and CRS with larger depth were responsible for the strength enhancement of EBM samples with two LSP treatments.
文摘The surface modification of materials such as Ti-6Al-4V is necessary to improve their wear resistant properties for use in tribological applications. In this paper it is shown that a laser with low power and tungsten inert gas (TIG) can be combined together for surface modification of Ti-6Al-4V alloy, and when performed in a controlled atmosphere of pure nitrogen or a mixture of nitrogen and argon, can produce a wear-resistant surface alloy. Compared with laser processing, a cheaper surface modification process has been developed involving a shorter processing time, which is free of stringent requirements such as a vacuum system.
文摘Ti-6AI-4V, among the Ti alloys, is the most widely used. In the present work, the behavior of Ti-6AI-4V alloy has been investigated by the uniaxial hot isothermal compression tests and a series of dilatometric experiments were also carried out to determine the transformation temperatures at different cooling rates. Specimens for hot compression tests were homogenized at 1050℃ for 10 min and then quickly cooled to different straining temperatures from 1050 to 850℃. Cooling rates were chosen fast enough to prevent high temperature transformation during cooling. Compression tests were conducted at temperatures from 1050 to 850℃ in steps of 50℃ at constant true strain rates of 10-3 or 10-2 s-1. The apparent activation energy for compression in two-phase region was calculated 420 kJ·mol-1. Partial globularization of a phase was observed in the specimen deformed at low strain rates and at temperatures near the transformation zone and annealed after deformation.
文摘This work aims to investigate the effects of hydrogen content(in the range of 0%-0.5%,mass fraction)and stress state (tension and compression)on the room-temperature mechanical properties of Ti-6Al-4V alloy through mechanical properties tests. The effects of hydrogen content on microstructure evolution of Ti-6Al-4V alloy is also examined by optical microscopy,X-ray diffractometry,transmission electron microscopy and scanning electron microscopy.The results show that hydrogen content and stress state have important effects on the room-temperature mechanical properties of Ti-6Al-4V alloy.Tensile strength and ultimate elongation decrease with increasing the hydrogen content,while compressive strength and ultimate reduction are improved after hydrogenation.The reason is that the intergranular deformation dominates at the state of tension.Hydrogen atoms in solid solution and hydrides at grain boundaries increase with increasing the hydrogen content and they can promote the initiation and propagation of cracks along grain boundaries.While the intragranular deformation dominates at the state of compression.The plastic beta phase and hydrides increase with increasing the hydrogen content and they improve the ultimate reduction and compressive strength.
基金supported by the Fundamental Research Funds for the Central Universities(Grant No.3102014JCQ01026)the Program of Introducing Talents of Discipline to Universities(Grant No.B08040)
文摘The cast Ti-6Al-4V alloy bars with different section sizes were fabricated by investment casting at counter-gravity condition with the mold temperatures of 300 °C and 650 °C, respectively. The microstructure of the alloy was observed by means of OM and SEM, and the effect of mold temperature and casting dimension on tensile properties was studied. Results show that equiaxed grains are obtained regardless of the casting dimension. β grain size tends to increase with an increase in mold temperature. Hot isostatic pressing of the alloy was carried out for tensile properties' comparison. Room temperature tensile test results show that Ti-6Al-4V alloy produced via counter-gravity casting has good balance of strength and ductility after hot isostatic pressing(HIP). The alloy shows higher ductility due to the elimination of porosity. In both cast and HIP status, the tensile strength is inclined to decrease with an increase in mold temperature, while the ductility is prone to slightly increase. Both the strength and ductility tend to decrease with an increase in the casting dimension.
文摘Hot crack is one of common defects in castings, which often results in failure of castings. This work studies the formation of hot crack during cold crucible continuous casting by means of experiments and theoretical analysis. The results show that hot crack occurs on the surface and in the circumference of ingots, where the solidified shell and the solidification front meet each other. The tendency of hot cracking decreases with the increase of withdrawal velocities in some extent. The hot crack is caused mainly by the friction force between the shell and the crucible inner wall, and it takes place when the stress resulting from friction exceeds the tensile strength of the shell. The factors of μ_m, η_t, η_s and η_m, affecting hot cracks are analyzed and verified. In order to decrease the tendency of hot cracks, technical parameters should be optimized by decreasing μ_m, η_t, η_s and η_m.
基金Funded by the National Natural Science Foundation of China(No.50801057)the Engineering Research Center of Nano-Geo Materials of Ministry of Education,China University of Geosciences(No.NGM2018KF015)。
文摘The dynamic corrosion behaviors of Ti-6Al-4V alloy in acid artificial saliva containing fluoride ion were traced using electrochemical techniques,optical microscope,scanning electron microscopy,energy dispersive spectrometer and roughness tester.The experimental results indicate that a negative shift of corrosion potential as well as a continuous decrease in impedance for the alloy exists with increasing immersion time,and the degradation rate of the alloy presents the trend of first increase then decrease following the dissolution of passivation film and the formation of corrosion products.The accumulated fluoride ion on the alloy surface accelerates the fracture of passivation film,and the occurrence and development of corrosion of alloy are mainly located at the sites where the formation and shedding of white particles are composed of fluoride compounds,resulting in the decrease of corrosion resisting property of the alloy.A possible model is proposed to elaborate the dynamic corrosion behavior of the alloy.
基金This work is financially supported by Project 985-Automotive Engineering of Jilin University
文摘The aluminide coating process of Ti-6Al-4V alloys with different fillers(100wt.% Al_2O_3,50wt% Y_2O_3+50wt.% Al_2O_3 and 100wt.% Y_2O_3) for improvement of the oxidation resistance were investigated.The results show that the filler does not only participate in the aluminizing process,but also has much effect on the coating composition.The XRD analysis reveals that the aluminide coating with filler Al_2O_3 is predominant with TiAl_3 and TiAl phases;while the aluminide coatings with filler Y_2O_3+Al_2O_3 are predominant with Ti_3Al phase.The oxidation kinetics shows that different fillers affect greatly the oxidation resistance of aluminide coating,and the oxidation resistance of aluminized specimens with pack aluminizing filler Al_2O_3 are about 5-8 times than that of the aluminized specimens with other pack aluminizing fillers.
文摘The microstrueture and various hydrides precipitated in Ti-6A1-4V alloys containing hydrogen 0.16,0.58,0.87,1.49 wt-%,respectively,have been studied by means of TEM and X-ray diffraction.The Ti_3Al phase may precipitate when H over 0.58 wt-%.In the same time,the morphology of hydrides gradually changed from rugged sheets to narrow laths as H contents increased.The microstructure of highly H-doped alloys is obviously fine.A mas- sive hydride and the hydride with tetragonal lattice were observed in the specimen containing 1.49 wt-%H.The twin hydrides were found in the alloys with different H contents and the electron diffraction patterns of the twin hydrides can be served as a simple criterion for distin- guishing the cubic and tetragonal structures.
基金the Science and Technology Department of Hei Longjiang Province (No.GC05A209)the Science and Technology Department of Harbin (No.2005AA5CG046) for financial support.
文摘Numerical investigations of the 'banding' microstructure formation during solidification of Ti-6Al-4 V alloy in the centrifugal casting are conducted using a multi-scale model, which combines the finite difference method (FDM) at the macroscale with a cellular automaton (CA) model at the microscale. The macro model is used to simulate the fluid flow and heat transfer throughout the casting. The micro model is used to predict the nucleation and growth of microstructures. With the proposed model, numerical simulations are performed to study the influences of the nucleation density, mould rotation speed, and casting size upon the 'banding' microstructure formation. It is noted that changing the nucleation density has a minor effect on the microstructure formation. The rotation speed promotes the formation of 'banding' microstructure, which is more noticeable for larger size castings. The 'major mechanism responsible for this 'banding' phenomenon is the spatial variation in cooling rates created by centrifugal force.
文摘The effects of various hydrogen contents on the flow stress(σ),strain rate sensitivity expo- nent(m)and the tensile elongation(δ)of Ti-6Al-4V alloy were studied.The microstructure of the alloy was also investigated.The results indicate that,a suitable amount of hydrogen in the alloy can reduce the flow stress in the temperature range 800—860℃. Consequently,the superplastic temperature can be decreased and the ductility improved.
文摘The effect of triple annealing on stress relaxation of Ti-6Al-4V alloy as well as the microstructure after stress relaxation werestudied. The results showed that triple annealing treatment enhanced the resistance of stress relaxation performance, andwhen the temperature was rising, this effect became notable. The stress relaxation deformation mechanism is of dislocationcreep at 400℃ and recovery creep at 600℃.