The composition and production technology of the type of hot-rolled steel plate used in two-sided enameling were briefly described. The microstructure and mechanical properties before and after enameling were contrast...The composition and production technology of the type of hot-rolled steel plate used in two-sided enameling were briefly described. The microstructure and mechanical properties before and after enameling were contrastively investigated,and the precipitates in the samples were analyzed using transmission electron microscope and energy dispersive spectrometer. The results show the ferrite grain size of the steel plate after high-temperature enamel firing to be fine,with a large number of TiC and Ti;C;S;precipitates dispersed throughout the ferrite matrix. After two rounds of enamel firing at a temperature range of 800-890 ℃,its yield strength can still reach342 MPa. The results of a hydrogen permeation test show that the hydrogen storage properties of the steel plate are much better than those of ordinary structural carbon steel. A better bubble structure in the enamel layer can be obtained by this steel plate,with no fish-scale defects on the enameled steel-plate surface.展开更多
The analysis of bending in finishing rolling was performed. An asymmetrical rolling force model was established, and the upper and lower neutral points were determined. Thc bending which resulted from the asymmetrical...The analysis of bending in finishing rolling was performed. An asymmetrical rolling force model was established, and the upper and lower neutral points were determined. Thc bending which resulted from the asymmetrical rolling force at the roll gap was studied and related flexibility equations were proposed according to elastic mechanics. Moreover, material mechanics was used to analyze the effects of temperature difference and self-weight on the bending out of the roll gap, and the flexibility equations were constructed. The main factors on bending were summed up, and the bending rule in the rolling could be obtained. In addition practical calculation was made with the production data of ribbon steel from Laiwu Iron ＆ Steel Group Co. Ltd.展开更多
Since the 2050 mm hot strip mill was put into operation in 1989, Baosteel has made great achievements in increasing productivity, developing new process technologies and steel products and improving product quality. I...Since the 2050 mm hot strip mill was put into operation in 1989, Baosteel has made great achievements in increasing productivity, developing new process technologies and steel products and improving product quality. In the past 18 years from 1989 to 2007 ,Baosteel has constructed five hot strip mills with a total annual capacity of 19.8 Mt. Indices for technology standards, product categories and steel grades, product quality, both technically and economically, take the lead domestically or reached the world class level. As there are many hot strip mills that expected to be put into operation by the end of 2010 ,the overall annual capacity will exceed 30 Mt ,and the product will cover grain oriented （GO） Si steels and alloyed steels.展开更多
为提高热轧态0Cr21A16合金板材的组织均匀性和塑性,以改善其高温性能及冷加工特性,分析研究了不同温度的热处理试验及组织性能。采用光学显微镜、X射线衍射仪、Gleeble高温热拉伸实验、扫描电镜和纳米压痕仪等研究了热处理前后0Cr21Al6...为提高热轧态0Cr21A16合金板材的组织均匀性和塑性,以改善其高温性能及冷加工特性,分析研究了不同温度的热处理试验及组织性能。采用光学显微镜、X射线衍射仪、Gleeble高温热拉伸实验、扫描电镜和纳米压痕仪等研究了热处理前后0Cr21Al6合金板材的显微组织和力学性能。结果表明,通过热处理的方式改善0Cr21Al6合金板材的组织均匀性,在960℃保温6 min 40 s后快速冷却,晶粒平均尺寸为42μm,整体的晶粒尺寸相对于940、980、1000、1020℃热处理后较为均匀、细小,硬度和塑性达到最佳匹配,断裂韧度KIC在960℃处理下达到最佳,拥有最佳的综合性能,可有效避免生产过程中材料的脆性断裂问题。另外Gleeble实验显示1000℃以上的热处理温度不再适合于热加工。展开更多
文摘The composition and production technology of the type of hot-rolled steel plate used in two-sided enameling were briefly described. The microstructure and mechanical properties before and after enameling were contrastively investigated,and the precipitates in the samples were analyzed using transmission electron microscope and energy dispersive spectrometer. The results show the ferrite grain size of the steel plate after high-temperature enamel firing to be fine,with a large number of TiC and Ti;C;S;precipitates dispersed throughout the ferrite matrix. After two rounds of enamel firing at a temperature range of 800-890 ℃,its yield strength can still reach342 MPa. The results of a hydrogen permeation test show that the hydrogen storage properties of the steel plate are much better than those of ordinary structural carbon steel. A better bubble structure in the enamel layer can be obtained by this steel plate,with no fish-scale defects on the enameled steel-plate surface.
文摘The analysis of bending in finishing rolling was performed. An asymmetrical rolling force model was established, and the upper and lower neutral points were determined. Thc bending which resulted from the asymmetrical rolling force at the roll gap was studied and related flexibility equations were proposed according to elastic mechanics. Moreover, material mechanics was used to analyze the effects of temperature difference and self-weight on the bending out of the roll gap, and the flexibility equations were constructed. The main factors on bending were summed up, and the bending rule in the rolling could be obtained. In addition practical calculation was made with the production data of ribbon steel from Laiwu Iron ＆ Steel Group Co. Ltd.
文摘Since the 2050 mm hot strip mill was put into operation in 1989, Baosteel has made great achievements in increasing productivity, developing new process technologies and steel products and improving product quality. In the past 18 years from 1989 to 2007 ,Baosteel has constructed five hot strip mills with a total annual capacity of 19.8 Mt. Indices for technology standards, product categories and steel grades, product quality, both technically and economically, take the lead domestically or reached the world class level. As there are many hot strip mills that expected to be put into operation by the end of 2010 ,the overall annual capacity will exceed 30 Mt ,and the product will cover grain oriented （GO） Si steels and alloyed steels.
文摘为提高热轧态0Cr21A16合金板材的组织均匀性和塑性,以改善其高温性能及冷加工特性,分析研究了不同温度的热处理试验及组织性能。采用光学显微镜、X射线衍射仪、Gleeble高温热拉伸实验、扫描电镜和纳米压痕仪等研究了热处理前后0Cr21Al6合金板材的显微组织和力学性能。结果表明,通过热处理的方式改善0Cr21Al6合金板材的组织均匀性,在960℃保温6 min 40 s后快速冷却,晶粒平均尺寸为42μm,整体的晶粒尺寸相对于940、980、1000、1020℃热处理后较为均匀、细小,硬度和塑性达到最佳匹配,断裂韧度KIC在960℃处理下达到最佳,拥有最佳的综合性能,可有效避免生产过程中材料的脆性断裂问题。另外Gleeble实验显示1000℃以上的热处理温度不再适合于热加工。
