This paper presents an experimental study of the characterisation of local materials used in the construction and thermal insulation of buildings. These materials are compressed earth bricks stabilised with cement and...This paper presents an experimental study of the characterisation of local materials used in the construction and thermal insulation of buildings. These materials are compressed earth bricks stabilised with cement and sawdust. The thermal conductivity, diffusivity, effusivity, and specific heat of earth-based materials containing cement or sawdust have been determined. The results show that the blocks with earth + sawdust are better thermal insulators than the blocks with simple earth. We observe an improvement in thermal efficiency depending on the presence of sawdust or cement stabilisers. For cement stabilisation, the thermal conductivity increases (λ: 1.04 to 1.36 W·m<sup>-1</sup>·K<sup>-1</sup>), the diffusivity increases (from 4.32 × 10<sup>-7</sup> to 9.82 × 10<sup>-7</sup> m<sup>2</sup>·s<sup>-1</sup>), and the effusivity decreases (1404 - 1096 J·m<sup>-2</sup>·K<sup>-1</sup>·s<sup>-1/2</sup>). For sawdust stabilisation, the thermal conductivity decreases (λ: 1.04 to 0.64 W·m<sup>-1</sup>·K<sup>-1</sup>), the diffusivity increases (from 4.32 × 10<sup>-7</sup> to 5.9 × 10<sup>-7</sup> m<sup>2</sup>·s<sup>-1</sup>), and the effusivity decreases (1404 - 906 J·m<sup>-2</sup>·K<sup>-1</sup>·s<sup>-1/2</sup>). Improving the structural and thermal efficiency of BTC via stabilisation with derived binders or cement is beneficial for the load-bearing capacity and thermal performance of buildings.展开更多
The utilization of vortex generators to increase heat transfer from cylinders installed inside a duct is investigated.In particular,a channel containing eight cylinders with volumetric heat sources is considered for d...The utilization of vortex generators to increase heat transfer from cylinders installed inside a duct is investigated.In particular,a channel containing eight cylinders with volumetric heat sources is considered for different values of the Reynolds number.The effective possibility to use vortex generators with different sizes to increase heat transfer and,consequently,reduce the surface temperature of the cylinders is examined.Also,the amount of pressure drop inside the channel due to the presence of vortex generators is considered and compared with the cases without vortex generators.The results show that although the addition of generators increases the pressure drop,it strongly contributes to increase the heat transfer coefficient inside the duct(up to 80–90%).展开更多
Coupling efficiency between the localized surface plasmons(LSPs) of metal nanoparticles(NPs) and incident light dominates the sensitivities of plasmon-based sensing spectroscopies and imaging techniques, e.g., surface...Coupling efficiency between the localized surface plasmons(LSPs) of metal nanoparticles(NPs) and incident light dominates the sensitivities of plasmon-based sensing spectroscopies and imaging techniques, e.g., surfaceenhanced Raman scattering(SERS) spectroscopy. Many endogenous features of metal NPs(e.g., size, shape,aggregation form, etc.) that have strong impacts on their LSPs have been discussed in detail in previous studies.Here, the polarization-tuned electromagnetic(EM) field that facilitates the LSP coupling is fully discussed.Numerical analyses on waveguide-based evanescent fields(WEFs) coupled with the LSPs of dispersed silver nanospheres and silver nano-hemispheres are presented and the applicability of the WEF-LSPs to plasmon-enhanced spectroscopy is discussed. Compared with LSPs under direct light excitation that only provide 3–4 times enhancement of the incidence field, the WEF-LSPs can amplify the electric field intensity about 30–90 times(equaling the enhancement factor of 10~6–10~8 in SERS intensity), which is comparable to the EM amplification of the SERS"hot spot" effect. Importantly, the strongest region of EM enhancement around silver nanospheres can be modulated from the gap region to the side surface simply by switching the incident polarization from TM to TE, which widely extends its sensing applications in surface analysis of monolayer of molecule and macromolecule detections. This technique provides us a unique way to achieve remarkable signal gains in many plasmon-enhanced spectroscopic systems in which LSPs are involved.展开更多
Bitumen requirement in hot mix asphalt (HMA) is directly dependent on the surface area of the aggregates in the mix, which in turn has effect on the asphalt film thickness and the flow characteristics. The surface a...Bitumen requirement in hot mix asphalt (HMA) is directly dependent on the surface area of the aggregates in the mix, which in turn has effect on the asphalt film thickness and the flow characteristics. The surface area of aggregate blend in HMA is calculated using the specific surface area factors assigned to percentage passing through some specific standard sieve sizes and the imaging techniques. The first process is less capital intensive, but purely manual and labour intensive and prone to human errors. Imaging techniques though eliminating the human errors, still have limited use due to capital intensiveness and requirement of well-established ]aboratories with qualified technicians. Most of the developing countries like India are shortage of well-equipped laboratories and qualified technicians. To overcome these difficulties, the present mathematical model has been developed to estimate the surface area of aggregate blend of HMA from physical properties of aggregates evaluated using simple laboratory equipment. This model has been validated compared with the existing established methods of calculations and can be used as one of the tools in different developing and under developed countries for proper design of HMA.展开更多
文摘This paper presents an experimental study of the characterisation of local materials used in the construction and thermal insulation of buildings. These materials are compressed earth bricks stabilised with cement and sawdust. The thermal conductivity, diffusivity, effusivity, and specific heat of earth-based materials containing cement or sawdust have been determined. The results show that the blocks with earth + sawdust are better thermal insulators than the blocks with simple earth. We observe an improvement in thermal efficiency depending on the presence of sawdust or cement stabilisers. For cement stabilisation, the thermal conductivity increases (λ: 1.04 to 1.36 W·m<sup>-1</sup>·K<sup>-1</sup>), the diffusivity increases (from 4.32 × 10<sup>-7</sup> to 9.82 × 10<sup>-7</sup> m<sup>2</sup>·s<sup>-1</sup>), and the effusivity decreases (1404 - 1096 J·m<sup>-2</sup>·K<sup>-1</sup>·s<sup>-1/2</sup>). For sawdust stabilisation, the thermal conductivity decreases (λ: 1.04 to 0.64 W·m<sup>-1</sup>·K<sup>-1</sup>), the diffusivity increases (from 4.32 × 10<sup>-7</sup> to 5.9 × 10<sup>-7</sup> m<sup>2</sup>·s<sup>-1</sup>), and the effusivity decreases (1404 - 906 J·m<sup>-2</sup>·K<sup>-1</sup>·s<sup>-1/2</sup>). Improving the structural and thermal efficiency of BTC via stabilisation with derived binders or cement is beneficial for the load-bearing capacity and thermal performance of buildings.
文摘The utilization of vortex generators to increase heat transfer from cylinders installed inside a duct is investigated.In particular,a channel containing eight cylinders with volumetric heat sources is considered for different values of the Reynolds number.The effective possibility to use vortex generators with different sizes to increase heat transfer and,consequently,reduce the surface temperature of the cylinders is examined.Also,the amount of pressure drop inside the channel due to the presence of vortex generators is considered and compared with the cases without vortex generators.The results show that although the addition of generators increases the pressure drop,it strongly contributes to increase the heat transfer coefficient inside the duct(up to 80–90%).
基金National Natural Science Foundation of China(NSFC)(21373096,21573087,21573092,91441105)National Instrumentation Program(NIP)of the Ministry of Science and Technology of the People’s Republic of China(MOST)(2011YQ03012408)Science and Technology Development Program Funded Projects of Jilin Province
文摘Coupling efficiency between the localized surface plasmons(LSPs) of metal nanoparticles(NPs) and incident light dominates the sensitivities of plasmon-based sensing spectroscopies and imaging techniques, e.g., surfaceenhanced Raman scattering(SERS) spectroscopy. Many endogenous features of metal NPs(e.g., size, shape,aggregation form, etc.) that have strong impacts on their LSPs have been discussed in detail in previous studies.Here, the polarization-tuned electromagnetic(EM) field that facilitates the LSP coupling is fully discussed.Numerical analyses on waveguide-based evanescent fields(WEFs) coupled with the LSPs of dispersed silver nanospheres and silver nano-hemispheres are presented and the applicability of the WEF-LSPs to plasmon-enhanced spectroscopy is discussed. Compared with LSPs under direct light excitation that only provide 3–4 times enhancement of the incidence field, the WEF-LSPs can amplify the electric field intensity about 30–90 times(equaling the enhancement factor of 10~6–10~8 in SERS intensity), which is comparable to the EM amplification of the SERS"hot spot" effect. Importantly, the strongest region of EM enhancement around silver nanospheres can be modulated from the gap region to the side surface simply by switching the incident polarization from TM to TE, which widely extends its sensing applications in surface analysis of monolayer of molecule and macromolecule detections. This technique provides us a unique way to achieve remarkable signal gains in many plasmon-enhanced spectroscopic systems in which LSPs are involved.
文摘Bitumen requirement in hot mix asphalt (HMA) is directly dependent on the surface area of the aggregates in the mix, which in turn has effect on the asphalt film thickness and the flow characteristics. The surface area of aggregate blend in HMA is calculated using the specific surface area factors assigned to percentage passing through some specific standard sieve sizes and the imaging techniques. The first process is less capital intensive, but purely manual and labour intensive and prone to human errors. Imaging techniques though eliminating the human errors, still have limited use due to capital intensiveness and requirement of well-established ]aboratories with qualified technicians. Most of the developing countries like India are shortage of well-equipped laboratories and qualified technicians. To overcome these difficulties, the present mathematical model has been developed to estimate the surface area of aggregate blend of HMA from physical properties of aggregates evaluated using simple laboratory equipment. This model has been validated compared with the existing established methods of calculations and can be used as one of the tools in different developing and under developed countries for proper design of HMA.