A 1040°C-hot-deformed Ti_2AlNb-based alloy solution-treated at 950°C and aged at different temperatures was quantitatively investigated. The microstructure, size of the phase, and microhardness of the deform...A 1040°C-hot-deformed Ti_2AlNb-based alloy solution-treated at 950°C and aged at different temperatures was quantitatively investigated. The microstructure, size of the phase, and microhardness of the deformed alloys were measured. The results indicated that the microstructure of the deformed Ti_2AlNb-based alloy specimens comprise coarse O lath, fine O lath, equiaxed O/α_2, and acicular O phase. More O phase was generated in the deformed alloy after heat treatment because the acicular O phase was more likely to nucleate and grow along the deformation-induced crystal defects such as dislocations and subgrain boundaries. After deformation and subsequent heat treatment, the acicular O phase of the resultant alloy became finer compared to that of the undeformed alloy, and the acicular O phase became coarser and longer with the elevated aging temperature, while the width of the O lath exhibited unobvious variations. The hot deformation facilitated the dissolution of the O lath but accelerated the precipitation of the acicular O phase. When the 950°C-solution-treated deformed Ti_2AlNb-based alloy was then aged at 750°C for different periods, the phase content was nearly invariable, O and B2 phases eventually reached equilibrium, and the microstructure became stable and homogeneous.展开更多
The isothermal compression test at elevated temperature was carried out for aluminum sheets prepared by different melt-treatment methods with aid of dynamic hot/mechanical simulation experimental technology. The mater...The isothermal compression test at elevated temperature was carried out for aluminum sheets prepared by different melt-treatment methods with aid of dynamic hot/mechanical simulation experimental technology. The material constants of hot deformation have been solved by multivariate regression directly. Influence of metallurgy factors on the constants was analyzed. The results show that at some strain, the relationship of sheets’ flow stress with deformation temperature and strain rate can be expressed more suitably with Arrhenius equation modified by hyperbolic sine function. Structure factor A1, stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q all increase with increment of strain, while stress exponent n decreases gradually. The bigger α value or the smaller n value is, the more obvious the dynamic softening is, but the α value will increase for the metallurgy defects existing in the sheets. Influence of melt-treatment on Q depends upon the synthesis effect of all kinds of metallurgy defects. The Q and n values of the sheet prepared by high-efficient melt-treatment are the least, while the m value is the biggest, and the sheet can deform easily and evenly.展开更多
Thermal fatigue checking is the general failure of hot work die steels, which is relative with the structures and properties of the steels and the stress alternated during the employment. The Uddeholm test method on t...Thermal fatigue checking is the general failure of hot work die steels, which is relative with the structures and properties of the steels and the stress alternated during the employment. The Uddeholm test method on thermal fatigue is used to compare the behaviors of different samples, which are treated with plasma nitriding、plasma sulfur carbon nitriding、boronizing or not treated. The results show that the nitriding improves the thermal fatigue property of the tool steel, while the plasma sulfur carbon nitriding and the boronizing impair the property. The mechanisms are induced as follows. By increasing the hardness and changing the stress distribution in the surface layer, surface treatment can decrease the plastic deformation and the tensile stress during the cycling. Therefore, the generation and growth of the cracks are restrained. On the other hand, as results of surface treating, in the surface layer the toughness declines and the expanding coefficient ascendes; the latter change caused the strengthening of the tensile and compressive stress during the cycling. Thus the resistance to thermal fatigue is weakened. Whether or not the surface treatment is favor to thermal fatigue of tool steels relies on which factor is dominant.展开更多
Experiments were conducted to observe the effect of pre-harvest calcium (Ca) applied as calcium chloride (1% W/V) and postharvest hot water treatment (HWT) on “Royal Delicious” apples. For this, apples were divided ...Experiments were conducted to observe the effect of pre-harvest calcium (Ca) applied as calcium chloride (1% W/V) and postharvest hot water treatment (HWT) on “Royal Delicious” apples. For this, apples were divided in 4 lots viz., untreated (neither Ca nor HWT), Ca alone (pre-harvest 3 sprays of CaCl2 (1.0% w/v) in the orchard), HWT (42℃ for 2 h). Apples of all four lots were stored in cold storage maintained at 0℃ ± 1℃ and 90% - 95% relative humidity for 6 months. After storage, fruits were removed to ambient conditions for 5 days, and then observations on decay area and incidence, bitter pit incidence, fruit Ca content, lipoxygenase (LOX) and antioxidant (AOX) activity, fruit firmness and fruit quality parameters were recorded. After 6 months in cold storage plus 5 day at 22℃ ± 2℃ and 70% + 4% RH, apples, which received Ca as pre-harvest spray or those which received postharvest hot water treatment or Ca + HWT had significantly lesser decay area (decay lesions) caused by Penicillium expansum or Botrytis cinerea than untreated ones (control). Ca + HWT treatment was significantly more effective on B. cinerea than P. expansum. Untreated apples exhibited higher incidence of bitter pit (18.2%) than those treated with Ca or HWT or both. Fruit Ca content (2.92% DM) were significantly lower and conversely the LOX activity (6.9 μmoles min–1×g–1FW) was higher in untreated apples. Similarly, total phenolics and AOX activity were also lower in the untreated apples than Ca or HWT treated. HWT or Ca treated apples have beneficial effects on fruit firmness, peel colour and quality parameters like TSS and ascorbic acid content. Thus, it is concluded that pre-harvest sprays of calcium chloride with postharvest HWT is highly useful for “Royal Delicious” for reducing decay loss, maintaining firmness, high levels of antioxidants and fruit quality.展开更多
Broccoli was stored at 0, 10, or 20℃after immersion in hot water (38 - 52℃) for 10 or 30 min. Yellowing of broccoli was significantly slowed and shelf life significantly increased when broccoli was treated with hot ...Broccoli was stored at 0, 10, or 20℃after immersion in hot water (38 - 52℃) for 10 or 30 min. Yellowing of broccoli was significantly slowed and shelf life significantly increased when broccoli was treated with hot water at 42 - 46℃and then stored at 10 or 20℃. Heat injury occurred when treatment was higher than 46℃in some varieties. Broccoli lasted 2-3 days longer when stored at 10℃ and 1-2 days longer when stored at 20℃ after hot water treatment at 46℃. There was no significant effect of treatment on shelf life after long time storage at 0℃. Weight loss was reduced by hot water treatment and the respiration behavior of the broccoli was also changed.展开更多
Hot compressive deformation of Ti600 alloy after thermo hydrogen treatment (THT) was carried out within hydrogen content range of 0-0.5%, temperature range of 760-920 ℃ and strain rate range of 0.01-10 s-1. The flow ...Hot compressive deformation of Ti600 alloy after thermo hydrogen treatment (THT) was carried out within hydrogen content range of 0-0.5%, temperature range of 760-920 ℃ and strain rate range of 0.01-10 s-1. The flow stress of Ti600 alloy after THT was obtained under hot deformation condition, and the influence of hydrogen on work-hardening rate (S*), strain energy density (U*), and deformation activation energy (Q) was analysed. The results show that the flow stress of Ti600 alloy decreases remarkably with the increase of hydrogen when the hydrogen content is less than 0.3%. Both S* and U* decrease with the increase of hydrogen when the hydrogen content is less than 0.3%, and when the hydrogen content is more than 0.3%, S* and U* increase with hydrogen addition. The value of Q decreases with the increase of strain at the same hydrogen content. The addition of small quantity of hydrogen leads to an increase of Q at small strain values, and when the strain reaches 0.6, the value of Q decreases gradually with the increase of hydrogen. When the hydrogen content is within the range of 0.1%-0.3%, the flow stress of Ti600 alloy is decreased when being deformed at the temperature range of 760-920 ℃.展开更多
This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused laye...This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused layer. XRD and SEM energy spectrum prove that trace RE element actually penetrates into the surface layer of steels. The result shows that RE can reduce the gradient of change of hardness in diffused layer, improve the morphology and distribution of compounds , and reduce the degree of surface alligator crack for thermal fatigue. The behavior of thermal fatigue of hot-working die steels is raised by 70% or so after the application of RE. The effect of RE is analysed according to the theory.展开更多
Hot medicated cornpress treatment belongs to an external treatment and is a kindof moxibustion. ″Feng Qi Ai″ prescription was recorded in Yi Fang Lei Ju. Zhu Xu Men, Rui ZhuTang Fang. In the treatment, pain in the l...Hot medicated cornpress treatment belongs to an external treatment and is a kindof moxibustion. ″Feng Qi Ai″ prescription was recorded in Yi Fang Lei Ju. Zhu Xu Men, Rui ZhuTang Fang. In the treatment, pain in the loin and the knees, cold-pain around the navel and in theabdornen,diarrhea due to deficiency and cold and other diseases are treated by combination of drugswith hot compress- We have irnproved the treatment and extended the range of its indication. It wasused for treatment 0f menorrhalgia due to cold uterine, gastralgia due to coId of rniddle-jiao, sciatica’periarthritis of shoulder, systremma,piriformis syndrome with good results.展开更多
In the present paper, a total of 109 asthma patients were randomly divided into treatment group (red hot needle, n=62) and control group (conventional acupuncture, n=47). The treatment was conducted beginning from the...In the present paper, a total of 109 asthma patients were randomly divided into treatment group (red hot needle, n=62) and control group (conventional acupuncture, n=47). The treatment was conducted beginning from the first day of the first 10 day period of the Dog Days. After successive two years’ treatment, results showed that of the 62 and 47 cases in treatment and control groups, 16 and 7 were cured basically, 37 and 16 had remarkable improvement, 8 and 12 were ameliorated, 1 and 10 failed in the treatment, with the effective rate being 98.4% and 78.7% respectively, displaying that the therapeutic effect of treatment group was significantly superior to that of control group (P<0.01).展开更多
Hemp sesbania (Sesbania exaltata) plants (>30 cm tall) sprayed with hot water (45°C – 95°C), followed by spray applications of fungal spores of Colletotrichum truncatum (CT) at 1.0 × 107 spore...Hemp sesbania (Sesbania exaltata) plants (>30 cm tall) sprayed with hot water (45°C – 95°C), followed by spray applications of fungal spores of Colletotrichum truncatum (CT) at 1.0 × 107 spores/ml-1 and 22°C – 25°C, suspended either in: 0.2% Silwet L-77 surfactant (SW);unrefined corn oil (CO)/distilled water (1:1, v:v);or 0.2% SW in CO were controlled by 80% - 95%, 12 days after treatment (DAT) under greenhouse conditions. These treatments also reduced dry weight accumulation of this weed. Plants treated with hot water without CT were also injured at temperatures ≥35°C (5% mortality), and 60% mortality at 95°C. Artificial dew treatments (25°C, 12 h), imposed on plants after the treatment protocols above, had little or no effect on weed mortality or dry weight reduction compared to treated plants without dew. Under field conditions, 85% control of hemp sesbania was achieved 12 - 15 DAT when a pre-treatment with hot water (65°C) was followed immediately with a CT application at the spore concentration as described above. Plants in field tests treated with CT without a hot water treatment were visually unaffected, with no mortality or plant biomass reductions recorded 15 DAT. These results suggest that use of hot water may be an important tool for improving the infectivity and bioherbicidal potential of some plant pathogens.展开更多
The vacuum treatment for simultaneous desulphurization and dephosphorization of hot metal and molten steel with pre-melted CaO-based slag was carried out.For pre-treatment of hot metal,both desulphurization and dephos...The vacuum treatment for simultaneous desulphurization and dephosphorization of hot metal and molten steel with pre-melted CaO-based slag was carried out.For pre-treatment of hot metal,both desulphurization and dephosphorization are improved with the increase of CaO in slag,but deteriorated with the increase of CaF2 in slag.The average desulphurization and dephosphorization rate is 68.83 % and 78.46 %,respectively.For molten steel,the substitution of BaO for CaO in slag has minor effect on simultaneous desulphurization and dephosphorization.The desulphurization and dephosphorization rate is higher than 90% and 50% respectively with the lowest final sulfur and phosphorus mass percent being 0.001 2% and 0.010%,respectively.The overall effect of simultaneous desulphurization and dephosphorization of molten steel is better than that of hot metal.展开更多
The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show ...The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.展开更多
基金the National Natural Science Foundation of China(Nos.51474156 and U1660201)the National Magnetic Confinement Fusion Energy Research Program of China(No.2015GB119001)for their grants and financial supports
文摘A 1040°C-hot-deformed Ti_2AlNb-based alloy solution-treated at 950°C and aged at different temperatures was quantitatively investigated. The microstructure, size of the phase, and microhardness of the deformed alloys were measured. The results indicated that the microstructure of the deformed Ti_2AlNb-based alloy specimens comprise coarse O lath, fine O lath, equiaxed O/α_2, and acicular O phase. More O phase was generated in the deformed alloy after heat treatment because the acicular O phase was more likely to nucleate and grow along the deformation-induced crystal defects such as dislocations and subgrain boundaries. After deformation and subsequent heat treatment, the acicular O phase of the resultant alloy became finer compared to that of the undeformed alloy, and the acicular O phase became coarser and longer with the elevated aging temperature, while the width of the O lath exhibited unobvious variations. The hot deformation facilitated the dissolution of the O lath but accelerated the precipitation of the acicular O phase. When the 950°C-solution-treated deformed Ti_2AlNb-based alloy was then aged at 750°C for different periods, the phase content was nearly invariable, O and B2 phases eventually reached equilibrium, and the microstructure became stable and homogeneous.
基金Project(JA04251) supported by the Education Department of Fujian Province, China Project(E0210011) supported by the Natural Science Foundation of Fujian Province, China
文摘The isothermal compression test at elevated temperature was carried out for aluminum sheets prepared by different melt-treatment methods with aid of dynamic hot/mechanical simulation experimental technology. The material constants of hot deformation have been solved by multivariate regression directly. Influence of metallurgy factors on the constants was analyzed. The results show that at some strain, the relationship of sheets’ flow stress with deformation temperature and strain rate can be expressed more suitably with Arrhenius equation modified by hyperbolic sine function. Structure factor A1, stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q all increase with increment of strain, while stress exponent n decreases gradually. The bigger α value or the smaller n value is, the more obvious the dynamic softening is, but the α value will increase for the metallurgy defects existing in the sheets. Influence of melt-treatment on Q depends upon the synthesis effect of all kinds of metallurgy defects. The Q and n values of the sheet prepared by high-efficient melt-treatment are the least, while the m value is the biggest, and the sheet can deform easily and evenly.
文摘Thermal fatigue checking is the general failure of hot work die steels, which is relative with the structures and properties of the steels and the stress alternated during the employment. The Uddeholm test method on thermal fatigue is used to compare the behaviors of different samples, which are treated with plasma nitriding、plasma sulfur carbon nitriding、boronizing or not treated. The results show that the nitriding improves the thermal fatigue property of the tool steel, while the plasma sulfur carbon nitriding and the boronizing impair the property. The mechanisms are induced as follows. By increasing the hardness and changing the stress distribution in the surface layer, surface treatment can decrease the plastic deformation and the tensile stress during the cycling. Therefore, the generation and growth of the cracks are restrained. On the other hand, as results of surface treating, in the surface layer the toughness declines and the expanding coefficient ascendes; the latter change caused the strengthening of the tensile and compressive stress during the cycling. Thus the resistance to thermal fatigue is weakened. Whether or not the surface treatment is favor to thermal fatigue of tool steels relies on which factor is dominant.
文摘Experiments were conducted to observe the effect of pre-harvest calcium (Ca) applied as calcium chloride (1% W/V) and postharvest hot water treatment (HWT) on “Royal Delicious” apples. For this, apples were divided in 4 lots viz., untreated (neither Ca nor HWT), Ca alone (pre-harvest 3 sprays of CaCl2 (1.0% w/v) in the orchard), HWT (42℃ for 2 h). Apples of all four lots were stored in cold storage maintained at 0℃ ± 1℃ and 90% - 95% relative humidity for 6 months. After storage, fruits were removed to ambient conditions for 5 days, and then observations on decay area and incidence, bitter pit incidence, fruit Ca content, lipoxygenase (LOX) and antioxidant (AOX) activity, fruit firmness and fruit quality parameters were recorded. After 6 months in cold storage plus 5 day at 22℃ ± 2℃ and 70% + 4% RH, apples, which received Ca as pre-harvest spray or those which received postharvest hot water treatment or Ca + HWT had significantly lesser decay area (decay lesions) caused by Penicillium expansum or Botrytis cinerea than untreated ones (control). Ca + HWT treatment was significantly more effective on B. cinerea than P. expansum. Untreated apples exhibited higher incidence of bitter pit (18.2%) than those treated with Ca or HWT or both. Fruit Ca content (2.92% DM) were significantly lower and conversely the LOX activity (6.9 μmoles min–1×g–1FW) was higher in untreated apples. Similarly, total phenolics and AOX activity were also lower in the untreated apples than Ca or HWT treated. HWT or Ca treated apples have beneficial effects on fruit firmness, peel colour and quality parameters like TSS and ascorbic acid content. Thus, it is concluded that pre-harvest sprays of calcium chloride with postharvest HWT is highly useful for “Royal Delicious” for reducing decay loss, maintaining firmness, high levels of antioxidants and fruit quality.
文摘Broccoli was stored at 0, 10, or 20℃after immersion in hot water (38 - 52℃) for 10 or 30 min. Yellowing of broccoli was significantly slowed and shelf life significantly increased when broccoli was treated with hot water at 42 - 46℃and then stored at 10 or 20℃. Heat injury occurred when treatment was higher than 46℃in some varieties. Broccoli lasted 2-3 days longer when stored at 10℃ and 1-2 days longer when stored at 20℃ after hot water treatment at 46℃. There was no significant effect of treatment on shelf life after long time storage at 0℃. Weight loss was reduced by hot water treatment and the respiration behavior of the broccoli was also changed.
基金Project supported by the Major Basic Research Program of National Security of China
文摘Hot compressive deformation of Ti600 alloy after thermo hydrogen treatment (THT) was carried out within hydrogen content range of 0-0.5%, temperature range of 760-920 ℃ and strain rate range of 0.01-10 s-1. The flow stress of Ti600 alloy after THT was obtained under hot deformation condition, and the influence of hydrogen on work-hardening rate (S*), strain energy density (U*), and deformation activation energy (Q) was analysed. The results show that the flow stress of Ti600 alloy decreases remarkably with the increase of hydrogen when the hydrogen content is less than 0.3%. Both S* and U* decrease with the increase of hydrogen when the hydrogen content is less than 0.3%, and when the hydrogen content is more than 0.3%, S* and U* increase with hydrogen addition. The value of Q decreases with the increase of strain at the same hydrogen content. The addition of small quantity of hydrogen leads to an increase of Q at small strain values, and when the strain reaches 0.6, the value of Q decreases gradually with the increase of hydrogen. When the hydrogen content is within the range of 0.1%-0.3%, the flow stress of Ti600 alloy is decreased when being deformed at the temperature range of 760-920 ℃.
文摘This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused layer. XRD and SEM energy spectrum prove that trace RE element actually penetrates into the surface layer of steels. The result shows that RE can reduce the gradient of change of hardness in diffused layer, improve the morphology and distribution of compounds , and reduce the degree of surface alligator crack for thermal fatigue. The behavior of thermal fatigue of hot-working die steels is raised by 70% or so after the application of RE. The effect of RE is analysed according to the theory.
文摘Hot medicated cornpress treatment belongs to an external treatment and is a kindof moxibustion. ″Feng Qi Ai″ prescription was recorded in Yi Fang Lei Ju. Zhu Xu Men, Rui ZhuTang Fang. In the treatment, pain in the loin and the knees, cold-pain around the navel and in theabdornen,diarrhea due to deficiency and cold and other diseases are treated by combination of drugswith hot compress- We have irnproved the treatment and extended the range of its indication. It wasused for treatment 0f menorrhalgia due to cold uterine, gastralgia due to coId of rniddle-jiao, sciatica’periarthritis of shoulder, systremma,piriformis syndrome with good results.
文摘In the present paper, a total of 109 asthma patients were randomly divided into treatment group (red hot needle, n=62) and control group (conventional acupuncture, n=47). The treatment was conducted beginning from the first day of the first 10 day period of the Dog Days. After successive two years’ treatment, results showed that of the 62 and 47 cases in treatment and control groups, 16 and 7 were cured basically, 37 and 16 had remarkable improvement, 8 and 12 were ameliorated, 1 and 10 failed in the treatment, with the effective rate being 98.4% and 78.7% respectively, displaying that the therapeutic effect of treatment group was significantly superior to that of control group (P<0.01).
文摘Hemp sesbania (Sesbania exaltata) plants (>30 cm tall) sprayed with hot water (45°C – 95°C), followed by spray applications of fungal spores of Colletotrichum truncatum (CT) at 1.0 × 107 spores/ml-1 and 22°C – 25°C, suspended either in: 0.2% Silwet L-77 surfactant (SW);unrefined corn oil (CO)/distilled water (1:1, v:v);or 0.2% SW in CO were controlled by 80% - 95%, 12 days after treatment (DAT) under greenhouse conditions. These treatments also reduced dry weight accumulation of this weed. Plants treated with hot water without CT were also injured at temperatures ≥35°C (5% mortality), and 60% mortality at 95°C. Artificial dew treatments (25°C, 12 h), imposed on plants after the treatment protocols above, had little or no effect on weed mortality or dry weight reduction compared to treated plants without dew. Under field conditions, 85% control of hemp sesbania was achieved 12 - 15 DAT when a pre-treatment with hot water (65°C) was followed immediately with a CT application at the spore concentration as described above. Plants in field tests treated with CT without a hot water treatment were visually unaffected, with no mortality or plant biomass reductions recorded 15 DAT. These results suggest that use of hot water may be an important tool for improving the infectivity and bioherbicidal potential of some plant pathogens.
基金Sponsored by Provincial Natural Science Foundation of Anhui of China
文摘The vacuum treatment for simultaneous desulphurization and dephosphorization of hot metal and molten steel with pre-melted CaO-based slag was carried out.For pre-treatment of hot metal,both desulphurization and dephosphorization are improved with the increase of CaO in slag,but deteriorated with the increase of CaF2 in slag.The average desulphurization and dephosphorization rate is 68.83 % and 78.46 %,respectively.For molten steel,the substitution of BaO for CaO in slag has minor effect on simultaneous desulphurization and dephosphorization.The desulphurization and dephosphorization rate is higher than 90% and 50% respectively with the lowest final sulfur and phosphorus mass percent being 0.001 2% and 0.010%,respectively.The overall effect of simultaneous desulphurization and dephosphorization of molten steel is better than that of hot metal.
基金Project(SKLSP201853) supported by the Fund of the State Key Laboratory of Solidification Processing in NWPU,ChinaProject(51625505) supported by the National Science Fund for Distinguished Young Scholars of China+1 种基金Project(U1537203) supported by the Key Program Project of the Joint Fund of Astronomy and National Natural Science Foundation of ChinaProject(KYQD1801) supported by the Scientific Research Foundation of Tianjin University of Technology and Education,China
文摘The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.
