Assessing the energy release characteristics during the middle detonation reaction stage of aluminized explosives

Afterburning behind the detonation front of an aluminized explosive releases energy on the millisecond timescale,which prolong the release of detonation energy and the energy release at different stages also shows significant differences.However,at present,there are few effective methods for evaluating the energy release characteristics of the middle reaction stage of such explosives,which can have a duration of tens to hundreds of microseconds.The present work demonstrates an approach to assessing the midstage of an aluminized explosive detonation based on a water push test employing a high degree of confinement.In this method,the explosive is contained in a steel cylinder having one end closed that is installed at the bottom of a transparent water tank.Upon detonation,the gaseous products expand in one direction while forcing water ahead of them.The resulting underwater shock wave and the interface between the gas phase products and the water are tracked using an ultra-high-speed framing and streak camera.The shock wave velocity in water and the expansion work performed by the gaseous detonation products were calculated to assess the energy release characteristics of aluminized explosives such as CL-20 and RDX in the middle stage of the detonation reaction.During the middle stage of the detonation process of these aluminized explosives,the aluminum reaction reduced the attenuation of shock waves and increased the work performed by gas phase products.A higher aluminum content increased the energy output while the presence of oxidants slowed the energy release rate.This work demonstrates an effective means of evaluating the performance of aluminized explosives.

Investigation and improvement of tiny spot defects on hot-dip galvanized automotive steel sheets

The causes of tiny spot defects on the surface of hot-dip galvanized automotive steel sheets were studied using scanning electron microscopy(SEM)and energy dispersive spectrometer(EDS),and effective control measures were introduced.The results show that rubbing against the top roller after galvanizing is easy due to the local thickness of tiny spot defect location coating;therefore,the surface morphology is different from the normal part.Three kinds of defects,namely zinc slag,small slivers,and pitting,are likely to cause local thickening of the coating after galvanizing,leading to the formation of tiny spots.Therefore,resolving the three types of defects can effectively control the generation of tiny spot defects.Among them,due to the hereditary nature of the small sliver defect,focusing on its control and supervision is necessary.

Research on the quasi-isentropic driving model of aluminized explosives in the detonation wave propagation direction

Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.

Influence of Si content on interface reaction of iron-based hot-dip aluminizing on Fe sheet

Based on the diffusion channel,the influence of Si content on the microstructure evolution of iron-based hot-dip Al-χSi coating was analyzed(χ=0,1.5 wt%,3.0 wt% and 7.0 wt%).The results show that the introduction of Si makes the reaction interface change from the lingual-tooth interface of hot-dip Al to the flat interface of hot-dip Al-Si.It also reduces the thickness of the alloy layer in the coating,especially the Fe_(2)Al_(5) layer.When the Si content is 1.5 wt%or 3.0 wt%,the diffusion channel crosses the conjugate line of the two-phase region(FeAl_(3)+liquid phase)into the FeAl_(3) single-phase region,and then moves to the region with higher Si content.Next,the diffusion channel cuts off the conjugate line of FeAl_(3)phase,τ_(1)/τ_(9) phase,and Fe_(2)Al_(5)phase,which promotes the form ofτ_(1)/τ_(9) phase.The formedτ_(1)/τ_(9) phase inhibits the diffusion between Fe and Al atoms.When the Si content is 7.0 wt%,the diffusion channel passes through the two-phase region(liquid phase+τ_(5))and enters theτ_(5) single-phase region.The form ofτ_(5) single-phase region has a strong inhibitory effect on the interatomic diffusion of Fe and Al,thereby reducing the thickness of the coating,especially the Fe_(2)Al_(5)layer.

Main controlling factors and exploration enlightenment of aluminous rock series gas reservoirs in Ordos Basin,NW China

Based on the data of outcrop,core,logging,gas testing,and experiments,the natural gas accumulation and aluminous rock mineralization integrated research was adopted to analyze the controlling factors of aluminous rock series effective reservoirs in the Ordos Basin,NW China,as well as the configuration of coal-measure source rocks and aluminous rock series reservoirs.A natural gas accumulation model was constructed to evaluate the gas exploration potential of aluminous rock series under coal seam in the basin.The effective reservoirs of aluminous rock series in the Ordos Basin are composed of honeycomb-shaped bauxites with porous residual pisolitic and detrital structures,with the diasporite content of greater than 80%and dissolved pores as the main storage space.The bauxite reservoirs are formed under a model that planation controls the material supply,karst paleogeomorphology controls diagenesis,and land surface leaching improves reservoir quality.The hot humid climate and sea level changes in the Late Carboniferous–Early Permian dominated the development of a typical coal-aluminum-iron three-stage stratigraphic structure.The natural gas generated by the extensive hydrocarbon generation of coal-measure source rocks was accumulated in aluminous rock series under the coal seam,indicating a model of hydrocarbon accumulation under the source.During the Upper Carboniferous–Lower Permian,the relatively low-lying area on the edge of an ancient land or island in the North China landmass was developed.The gas reservoirs of aluminous rock series,which are clustered at multiple points in lenticular shape,are important new natural gas exploration fields with great potential in the Upper Paleozoic of North China Craton.

Aluminizing Low Carbon Steel at Lower Temperatures

This study reports the significantly enhanced aluminizing behaviors of a low carbon steel at temperatures far below the austenitizing temperature, with a nanostructured surface layer produced by surface mechanical attrition treatment （SMAT）. A much thicker iron aluminide compound layer with a much enhanced growth kinetics of η-Fe2Al5 in the SMAT sample has been observed relative to the coarse-grained steel sample. Compared to the coarse-grained sample, a weakened texture is formed in the aluminide layer in the SMAT sample. The aluminizing kinetics is analyzed in terms of promoted difusivity and nucleation frequency in the nanostructured surface layer.

Formation of microstructural features in hot-dip aluminized AISI 321 stainless steel

Hot-dip aluminizing（HDA） is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions： an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al_7Cr and Al_3Fe dispersed in an Al matrix. Twinning was observed in both the Al_7Cr and the Al_3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe_2Al_5, Al_7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed.

Aluminizing Coating and Aluminizing-Y_2O_3 Coating Deposited by Pulsed Spark

Aluminizing coating and aluminizing-dispersed Y 2O 3 composite coating were prepared on 20 steel specimens by pulsed spark technique, which exhibited a micro-crystallized structure with grain size in the range of several ten to several hundred nanometers. It is shown that, after oxidation at 600 ℃ in air for 100 h, these two kinds of coatings have excellent resistance to high temperature oxidation and scale spallation, and the aluminizing-dispersed Y 2O 3 composite coating has even better property than the aluminizing coating. AFM, SEM, EDS and XRD were applied to analyze the surface morphology, composition and phases structure of these coatings and the oxide scale formed in oxidation. The mechanism for these coatings that how to enhance the oxidation resistance and scale spallation resistance was discussed by considering the factors, such as Al concentration on the selective oxidation of Fe-Al alloy, the effect of micro-crystallization, reactive element effect (REE) caused by dispersed Y 2O 3, etc.

Heat Transfer during the Solidification of Hot Dip Aluminizing Coating

Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity.Although the pulling speed is one of the most important parameters to control the coating thickness of aluminizing products,however,there are few publications on the mathematical modeling of pulling speed during the hot dip process.In order to describe the correlation among the pulling speed,coating thickness and solidification time,the principle of mass and heat transfer during the aluminizing process is investigated in this paper.The mathematical models are based on Navier-Stokes equation and heat transfer analysis.Experiments using the self-designed equipment are carried out to validate the mathematical models.Specifically,aluminum melt is purified at 730 ℃.The Cook-Norteman method is used for the pretreatment of Q235 steel plates.The temperature of hot dip aluminizing is set to 690 ℃ and thedipping time is set to 3 min.A direct current motor with stepless speed variation is used to adjust the pulling speed.The temperature change of the coating is recorded by an infrared thermometer,and the coating thickness is measured by using image analysis.The validate experiment results indicate that the coating thickness is proportional to the square root of pulling speed for the Q235 steel plate,and that there is a linear relationship between coating thickness and solidification time when the pulling speed is lower than 0.11 m/s.The prediction of the proposed model fits well with the experimental observations of the coating thickness.

Kinetic study on NaF-activated pack-aluminizing of pure titanium at 950-1100℃

Pure titanium samples were aluminized at 950,1025 and 1100 ℃ for 0-6 h in a pack containing 10%Al＋5%NaF＋85%Al2O3 in mass traction.The aluminized layers formed on the samples were characterized.The kinetic studies indicated that the diffusion of Al-bearing gases through the pack is the rate-controlling step in this process.The activation energy of 161.8 kJ/mol was calculated for this step.In addition,the mass gains of the aluminized samples were predicted using the partial pressures of gases in the pack and those adjacent to the samples surface.The predicted values are in good agreement wim the experimental measurements at 950 ℃ but are higher than those measured at 1025 and 1100 ℃.

Hot-Dip Coating of Lead-free Aluminum on Steel Substrates with Ultrasonic Vibration

Hot-dip coating has been practically employed in manufacturing zinc alloy coated steel sheets.However,it is difficult to coat aluminum alloy on a bulky steel substrate without sufficient preheating,because a rapidly solidified layer containing gas babbles is formed on a substrate surface.A variety of iron-aluminides are also formed at the interface of a steel and aluminum hot-dip coating system,which is the main difficulty in joining of steel with aluminum.Ultrasonic vibration was applied to a steel substrate during hot-dip coating of aluminum alloy to control a rapidly solidified layer and a brittle reaction layer.Hot dipping of columnar steel substrates into molten aluminum alloy （Al-2.7 mass fraction Si-4.6 mass fraction Sn） was carried out through the use of a Langevin oscillator with resonant frequency of 19.5 kHz.The application of ultrasonic vibration is quite effective to control a rapidly solidified layer and a surface oxide layer from a substrate surface by the sonocapillary effect based on a cavitation phenomenon,so that the intimate contact is achieved at the beginning of hot-dip coating.The application of ultrasonic vibration to hot-dipping is effective to control a reaction layer with less than 5 #m in thickness.An impact test exhibits that the good adhesive strength is approved in hot-dipped aluminum coatings with a thin reaction layer of approximately 5μm.

Pack Aluminizing of Copper

Aluminizing of Cu by a pack cementation process was performed to improve its surface properties.The effect of variation of pack aluminizing temperature from 800 to 900℃ and aluminizing time from 1 to 6 h on the microstructure and the thickness of the aluminide coating of Cu was investigated. Pack aluminizing of Cu significantly improved the microhardness and the oxidation resistance. The microhardness was increased about seven times and the oxidation resistance,after 96 h exposure in air at 900℃, was extremely increased ten times by aluminizing Cu at 900℃ for 3 h.

Analysis of Coating Microstructure of Hot-Dip Aluminum of Deformed Low-Carbon Steel Containing Rare Earth

The coating microstructure of hot-dip aluminum (HDA) of deformed low-carbon steel containing RE was analyzed by metallography microscopy, TEM and XRD, and the forming mechanism was also discussed. The results show that, the Fe_2Al_5 phase, on whose subcrystal boundaries, Al particles with the size of 7～30 μm existing on parallel linear are, grows a strong orientation. And the spread activation energy of Al is 155.22 kJ·mol -1. In addition, the effects of deformation on coating microstructure of hot-dip aluminum and the function of RE were preliminarily analyzed.

Oxidation Properties in CO_2 of Inconel Alloy 600 Coated by Simultaneous Aluminizing-Chromizing Process

IN 600 alloy was coated with two different types of coatings, Cr-modified aluminide coating this is called aluminizing-chromizing and Y-doped chromium modified aluminide coating this is called aluminizing-chromizing-yttriumizing. Diffusion coating was carried at 1 050℃ for 8 h under Ar atmosphere by simultaneous aluminizing-chromizing process and by simultaneous aluminizing-chromizing- yttriumizing. Cyclic oxidation tests were conducted on the uncoated and on the coated Inconel 600 alloy in the temperature range 800- 1 000℃ in CO2 for 100 h at 10 h cycle.The results showed that the oxidation kinetics for uncoated Inconel 600 alloy in CO2 is parabolic and the phases present are NiO, （Fe, Cr）2O3 , NiFe2O4 and NiCrO4. The oxidation kinetics for both coated systems in CO2 was found to be parabolic and the value ofkp for both coated systems were found to be lower than that for uncoated Inconel 600 alloy. Oxide phases that formed on coated systems are Al2O3 and NiCrO4. The role of yttrium can be attributed to its ability to improve the adherence of the oxide scale.

Recent development of UHSS and its hot-dip galvanizing processes in Baosteel

Baosteel has excelled in automotive steel sheets in the past three decades.It has made a significant contribution to the development of China’s automotive industry by producing a wide range of high-quality steel products.Some milestones achieved by Baosteel automotive steel sheet were briefly reviewed.The current challenges in producing ultra-high strength steel(UHSS),especially hot-dip galvanized UHSS,were summarized.The most current advancements in UHSS and the corresponding hot-dip galvanizing processes were discussed.The galvanizability of Si-Mn-added QP steel and DP steel, Mn-added TWIP steel, and Al-added low-density steel has been improved by different techniques in Baosteel.

RE-aluminithermic Aluminizing

The steel surface treatment by rare-earth aluminithermic aluminizing,which was utilized onthermal couple,buried parts of lightning arrester and silencer of automobile,has met with success.This new technique was studied by Beijing University of Science and Technology,BeijingIron-steel Institute and Jingdong Work of Corrosion-protective Materials cooperatively.The steel

UV-LED Curing Cationic Passivation Film for the Surface of Hot-Dip Aluminum-Zinc Coated Steel Plate

The surface treatment technology of hot aluminum-zinc steel plate and UV curing technology may be effectively combined in the present research. According to different light curing mechanisms, different formulations from UV curing surface treatment agents can be applied to the surface treatment of hot aluminum-zinc steel plate, mainly including 3-ethyl-3-benzoxy-methyl oxacyclobutane (TCM 104) and 3,4-epoxy-cyclohexylformic acid -3',4'-epoxy-cyclohexyl methyl ester (UVR 6110) as active diluents, high molecular weight polyfunctional oxacyclobutane as oligomer, triaryl sulfonium salt as a cationic photoinitiator, and an anthracene compound as a sensitizer. 385 nm LED lamp used as a radiation resource, the effects of the proportion of active diluent, the type and amount of photoinitiator, the amount of sensitizer, the curing temperature, and the amount of nano-SiO2 on the photocuring rate were investigated by photoper-scanning differential calorimetry (Photo-DSC). The experimental results show that the system has the fastest photocuring rate under the conditions of 8:2 ratio of TCM 104 to UVR 6110, 2.5% photoinitiator, 0.6% sensitizer, 0.2% nano-SiO2 additive, and 80˚C curing temperature. Based on addition of the appropriate number of various additives, the cationic photocuring surface treatment solution was prepared and further coated on the hot-dip galvalume steel plates. After curing, the passivation films were characterized by neutral salt spray test (NSST), Fourier transform infrared spectroscopy (FT-IR), electrochemical testing and other methods. The results show that the formulations could be cured at an energy of 150 mJ/cm2, and the overall performance of the passivation film could meet with the requirements of the downstream users.

Complex Boronized Layer on the Hot-dip Aluminized Steels and Its Surface Performances

Plain carbon steels were dipped in molten aluminum bath at 720°C ±5°C and diffused for 1, 2.5 and 6 hours respectively and then boronized at 950°C for 6 hours. The oxidation, hot-corrosion and abrasion resistance behavior were examined. The experimental results showed the compounds of the aluminized layer, from the surface to the matrix, were composed of Fe2Al5 ( n -phase ) .. Fe3Al ( -phase ) and a phase. The microstructure of aluminized plus complex boronized were similar to that simplex boronized. The XRD analysis results indicated that there existed Fe2B> Fe2AlB2and Fe2Als in this kind of layer. The simplex aluminized layers still remained bright gray appearance when oxidized at 950°C, but complex boronized layer was not able to resist oxidization at the temperature. Both the layers of complex boronized and aluminized had the same anti-oxidization level in the circulative oxidization tests, and also good anti-corrosion ability in molten salt medium. Under dry abrasive conditions, wear resistance of complex boronized layer was superior to the aluminized layer.

Chloride Corrosion of Reinforced Calcium Aluminate Cement Mortar

This paper describes a study on the corrosion behavior of steel reinforcement in CAC mortars via electrochemical methods including corrosion potential,electrochemical impedance,and linear polarization evaluation.Results indicate that there is a non-linear relationship between the corrosion degree of steel reinforcement in CAC mortar and the concentration of NaCl solution.The electrochemical parameters of specimens immersed in 3%NaCl solution suddenly drop at 40 days,earlier than 60 days of the reference.And the charge transfer resistivity of the specimen has decreased by 11 orders of magnitude at 40 days,showing an evident corrosion on steel reinforcement.However,it is interesting to notice that the corrosion is delayed by high external chloride concentration.The specimens immersed in 9%and 15%NaCl solutions remain in a relatively stable state within 120 days with slight pitting.The great corrosion protection of CAC concrete to embedded steel bars enables its wide application in marine.

Post-mortem Microstructural Study of Aluminous Refractory Brick Used in Channels of Blast Furnaces

Aluminous refractory materials with high alumina contents are widely used in the steel industry,and the higher the alumina content,the higher the working temperature.Properties such as high refractoriness and thermal shock resistance lead these refractory materials to be used as channel linings of blast furnaces,where they are exposed to the attack by slag,molten steel,working cycles and sudden temperature changes between 25℃(room temperature)and 1520℃(the temperature of molten pig iron).In this work,microstructural changes in post-mortem aluminous refractory bricks were investigated by apparent porosity,X-ray diffraction analysis(XRD),Fourier transform infrared spectroscopy(FTIR),scanning electron microscopy,and X-ray dispersion energy spectrometry(SEM/EDS).The results showed an increase in the apparent porosity and the bulk density and the presence of the phases mullite,sillimanite,alumina,and quartz in the post-mortem brick.Calcium and magnesium were not detected in the microstructure of the post-mortem brick,indicating that slags did not corrode these refractory materials.Therefore,the microstructural changes that occurred in the post-mortem bricks must be due to thermal cycling.In the X-ray diffraction(XRD)test,mullite,sillimanite,quartz,andα-alumina phases were identified.These results indicate that the aluminous refractory was obtained from sillimanite.In infrared spectroscopy(FTIR)it was possible to identify the vibration bands referring to the Si-O and Al-O bonds.The increase in the porosity is a result of cracks caused by work cycles at high temperatures and the temperature gradient to which the refractory was subjected during use.Through the micrograph it was possible to identify the presence of acicular mullite.The absence of magnesium and calcium in the microanalysis results by energy dispersed X-ray spectrometry(EDS)indicates that there was no infiltration by slag or liquid iron.These results indicate that the microstructural changes that occurred in the post-mortem aluminous refractory were of a thermal nature.