Effect of Hot-Rolled Oxide Scale on Dry/ Wet Cyclic Corrosion Behavior of Q370qNH Steel in Simulated Industrial Atmosphere Environment

The corrosion behavior of Q370qNH steel in the presence and absence of hot-rolled oxide scale in simulated industrial atmospheric environment was studied by dry/wet cycle accelerated corrosion experiments.The experimental results show that the corrosion type of bare steel is uneven overall corrosion and large size pitting corrosion in small areas;that of oxide scale sample is local dissolution corrosion and small size pitting corrosion in large areas,and corrosion rate is much smaller than that of bare steel.The corrosion products of both steels are composed ofα-FeOOH,γ-FeOOH,Fe_(2)O_(3),and Fe_(3)O_(4),but the formation mechanism is different.The bare steel generatesα-FeOOH andγ-FeOOH through“acid regeneration cycle mechanism”;the oxide scale sample generates hydroxides mainly through the gradual dissolution of the oxide film,and then through“the acid regeneration cycle mechanism”.With the extension of corrosion time,the electrochemical stability of the sample with oxide scale increases,but the change of tafel curve of bare steel sample is not obvious.In simulated industrial atmosphere,the existence of hot-rolled oxide scale can facilitate the formation of dense rust layer on the surface of Q370qNH steel,which is more protective than bare steel.

Influence of oxide scales on the corrosion behaviors of B510L hot-rolled steel strips

The influence of oxide scales on the corrosion behaviors of B510 L hot-rolled steel strips was investigated in this study. Focused ion beams and scanning electron microscopy were used to observe the morphologies of oxide scales on the surface and cross sections of the hot-rolled steel. Raman spectroscopy and X-ray diffraction were used for the phase analysis of the oxide scales and corrosion products. The corrosion potential and impedance were measured by anodic polarization and electrochemical impedance spectroscopy. According to the results, oxide scales on the hot-rolled strips mainly comprise iron and iron oxides. The correlation between mass gain and test time follows a power exponential rule in the damp-heat test. The corrosion products are found to be mainly composed of γ-Fe OOH, Fe3O4, ？-Fe OOH, and γ-Fe2O3. The contents of the corrosion products are different on the surfaces of the steels with and without oxide scales. The steel with oxide scales is found to show a higher corrosion resistance and lower corrosion rate.

“Quartus scale” of hot-rolled strip steels and its formation mechanism

The types and growth of various oxide scales formed during the different phases of the production of hotrolled strip steel products are reviewed. Similarities and differences between the ＂tertiary scale＂ on the surface of carbon steels at high temperatures and the oxide scale on pure iron are compared. The micro-structural features of the ＂final oxide scale＂ on the surface of strip steels at room temperature as well as the relationship between these features and the position of the steel coil （plate） and the subsequent processes of recoiling, temper rolling and trimming, etc. are summarized. The actual oxide scales retained on the commercial hot-rolled strip steels at room temperature have been proposed to define as ＂ quartus scale＂ for the first time. The micro-structural development and phase transformation of the initial ＂tertiary scale＂ during and after cooling and coiling are described. The reasons for the ＂tertiary scale＂ on carbon steels differing from the oxide scale formed on pure iron, and the major influencing factors in the formation of various types of ＂quartus scales＂ are analyzed from both thermodynamic and dynamic viewpoints. The development mechanism of ＂ quartus scales＂ is discussed and the potential effects of the ＂ quartus scale＂ state （thickness, constitution, structure and defects）, on the rusting and pickling properties of commercial hot-rolled strip steel, as well as on the mechanical properties of oxide scales are analyzed.

Effects of composite oxide scale on oxidation resistance of superalloy K273

A Si-containing K273 superalloy was made using intermediate frequency induction furnace in the study. In the testing of oxidation resistance, the oxidation process of the alloy specimens during the testing at 900℃ for 500 h was examined by oxidation weight gain method. The morphology and composition of the oxide scales were determined using scanning electron microscope （SEM） and X-ray diffraction （XRD）, respectively. The effects of the transferring of ions and electrons on the oxidation resistance were further analyzed microscopically by semiconductor oxide models. The results show that the composite oxide scales consist of Cr203, SiO2 and spinel- type oxide MCr204, with flat and compact structure, and fine grains in uniform distribution. All of these endow the superalloy K273 with strong oxidation resistance. The reason for the powerful oxidation resistance of the composite scale is that the formation process of P＋N type semiconductor oxide enables to consume most of the surplus negative and positive ions in the oxide scales, which makes the number of the mobile ions and electrons dropped enormously, and the transfer rate of them falls heavily. So the oxidation rate of the metal phase in the alloy matrix is reduced significantly.

Influence of Cr_2O_3-Al_2O_3 Composite Oxide Scale on Oxidation Resistance of ZG40Cr24

Test alloys ZG40Cr24 with alloying of 3 wt% aluminium were cast by intermediate frequency induction furnace. The oxidation resistance of test alloys at 1 000 ℃ for 500 hours was examined according to oxidation weight gain method. The scale morphology and composition were studied using scanning electron microscope （SEM） and X-ray diffraction （XRD） respectively. By energy dispersive spectroscopy （EDS） studies, a kind of composite oxide scale compounded highly by Cr2O3, Al2O3 and spinel MCr2O4 in molecule scale came into being at high temperature. With flat and compact structure, fine and even grains, such composite scale granted complete oxidation resistance to alloy ZG40Cr24. The oxidation resistance mechanism was studied deeply in electrochemistry corrosion. The P＋N semiconductor composite scale composed plenty of inner PN junctions, of which the unilateral conductive and the out-of-order arrangement endowed itself insulating in all directions. The positive and negative charges in scale could not move, and the mobile number and transferring rate of them both dropped enormously, as a result, the oxidation rate of the matrix metal was cut down greatly. So the composite scale presented excellent oxidation resistance.

Effect of Heating Rates on the Formable Oxide Scale on a C-Steel Surface

Oxide scale formation on a C-steel surface has been investigated using linear heating rates ranging from 0.1℃/min to 10℃/min at high temperatures. The studies on the oxide scale formation at high temperature (650℃) at slower heating rate (0.1℃/min) shows that the kinetic regime is linear. X-ray diffraction measurements revealed that the scale constituents are significantly influenced by the heating rate. The adherence of the scale was improved by using slower heating rate (0.1℃/min-≤650℃), while above such degree the scale was susceptible to cracking and flaking out of the alloy surface. In fact, the development of oxide growth stresses can cause considerable scale cracking. As well, variation of the crystallite sizes under the aforementioned conditions might affect the scale stacking to the alloy surface. The secondary electron detector images of the oxide scale shows that the scale was imperfectly smooth and there were a number of voids and defects in the scale skin, especially at fast heating rate. This observation could be attributed to defects of the as-received alloy. In general, slower heating rate reduced the defects of the scale and improved its adherence.

Improvement to anti-rust property of hot rolled rebar by compact oxide scale

A method was proposed to improve the anti-rust property of hot rolled rebar, which uses oil–water emulsion cooling instead of water cooling after hot rolling. The experiments were carried out by two cooling methods, one cooled by water, the other cooled by oil–water emulsion. The results of wet/dry cyclic accelerated corrosion test showed that the anti-rust property of rebar cooled by oil–water emulsion was better than that by water obviously. The results of OM, SEM and EPMA analysis indicated that these two scales contained three layers: an outer Fe_3O_4 layer, an intermediate Fe O layer with island-shaped pro-eutectoid Fe_3O_4, an inner eutectoid Fe_3O_4 layer. For the water cooled rebar, all three layers of oxide scale were relatively thin. Moreover, the scale had plenty of defects such as porosity, and crack. However, for the oil–water emulsion cooled rebar, all three layers of oxide scale were relatively thick and compact, which played an important role in protecting the rebar from atmospheric rust.

Thin Film of Perovskite Oxide with Atomic Scale p-n Junctions

Thin films of perovskite manganese oxide Lao.66Ca0.29K0.05MnO3（LCKMO） on Au/ITO（ITO=indium tin oxide） substrates were prepared by off-axis radio frequency magnetron sputtering and characterized by X-ray diffrac- tion（XRD）, high-resolution transmission electron microscopy（HRTEM）, and conductive atomic force microscopy （C-AFM） at room temperature. The thin films with thickness ranged from 100 nm to 300 nm basically show cubic structures with a=0.3886 nm, the same as that of the raw material used, but the structures are highly modulated. C-AFM results revealed that the atomic scale p-n junction feature of the thin films was the same as that of the single crystals. The preparation of the thin films thus further confirms the possibility of their application extending from micrometer-sized single crystals to macroscopic thin film.

DEFLECTION METHOD FROM TWO SIDES OXIDATION TO STUDY EFFECT OF Y ON INTERNAL STRESS OF OXIDE SCALES

Au investigation was carried ont of the effect of Y addition upon the internal stress of Al_2O_3 scale formed during oxidation of sputtering coating on Co-30Cr-6Al alloy and the growth stress of oxidized film on Fe-23Cr-5Al alloy heating up to 900℃ in air,using a specially designed deflection method from thin strip specimen with coat- ings,ion-implanted Y on one side and oxidized onto both sides.Results indicate that Y may decrease the internal stress of oxide scale on 2×10^(17) Y^+/cm^2 implanted Co- 30Cr-6Al coating,and increase one on 2×10^(16) Y^+/cm^2 implanted Fe-23Cr-5Al alloy. This seems due to whether or not Y promotes the plastic deformation of oxide scale.In addition,at initial oxidation stage,the change of growth stress of oxide scale formed on Y-implanted Co-30Cr-6Al coating may be related to the influence of Y on oxidation process of the coating.

Study on direct cold rolling of hot rolled austenitic stainless steel SUS 304 with oxide scale

The austenitic stainless steel SUS 304 with oxide scale was directly cold rolled at different reductions of 10%, 20% and 30% respectively. It was proved that the surface quality （lower surface roughness） of the cold rolled products was achieved after subsequent annealing and pickling possesses, compared to the conventional hot rolled No. 1 product, whereas the grain size, mechanical and corrosion-resistant properties were comparable to those of the No. 1 product.

Mill scale structure and damp heat corrosion performance of four 510L hot-rolled strips

In this study, the matrix structure, state and composition of the mill scales of four typical domestically made 510L hot-rolled strips were observed and analyzed by means of optical microscopy （OM） ,scanning electron microscopy （SEM） and X-ray diffraction （XRD）. The corrosion behavior of the steels with and without mill scales were investigated by means of hot-humid corrosion tests under the condition of relative humidity （ RH ） of 95% at 50℃ and 70℃, respectively. The results show that the matrix structures, state, composition and thickness of mill scales vary in the strips. The rusting starting time of the specimens with scales is generally a bit longer than that of the specimens without scales, but their corrosion mass-gain is higher. For these two kinds of specimens ,their corrosion rate increases significantly with the increase of temperature. The rusting behavior of the 510L strips produced by various plants is different due to the variations of hot-rolling processes and designed chemical compositions. Various relevant aspects should be taken into account in the evaluation of the corrosion behavior of hot-rolled strips.

Nitrogen and phosphorus removal in pilot-scale anaerobic-anoxic oxidation ditch system

To achieve high efficiency of nitrogen and phosphorus removal and to investigate the rule of simultaneous nitrification and denitrification phosphorus removal （SNDPR）, a whole course of SNDPR damage and recovery was studied in a pilot-scale, anaerobicanoxic oxidation ditch （OD）, where the volumes of anaerobic zone, anoxic zone, and ditches zone of the OD system were 7, 21, and 280 L, respectively. The reactor was fed with municipal wastewater with a flow rate of 336 L/d. The concept of simultaneous nitrification and denitrification （SND） rate （rSND） was put forward to quantify SND. The results indicate that： （1） high nitrogen and phosphorus removal efficiencies were achieved during the stable SND phase, total nitrogen （TN） and total phosphate （TP） removal rates were 80% and 85%, respectively; （2） when the system was aerated excessively, the stability of SND was damaged, and rSND dropped from 80% to 20% or less; （3） the natural logarithm of the ratio of NOx to NH4^＋ in the effluent had a linear correlation to oxidation-reduction potential （ORP）; （4） when NO3^- was less than 6 mg/L, high phosphorus removal efficiency could be achieved; （5） denitrifying phosphorus removal （DNPR） could take place in the anaerobic-anoxic OD system. The major innovation was that the SND rate was devised and quantified.

Effects of composite scale on high temperature oxidation resistance of Fe-Cr-Ni heat resistant alloy

Fe-Cr-Ni heat resistant alloys with aluminum and silicon addition, alone and in combination, were melted using an intermediate frequency induction furnace with a non-oxidation method. By the oxidation weight gain method, the oxidation resistances of the test alloys were determined at 1,200 ℃ for 500 hours. According to the oxidation weight gains, the oxidation kinetic curves were plotted and the functions were regressed by the least squares method. The results show that the oxidation kinetic curves follow the power function of y = ax^b （a〉0, 0〈b〈1）. The effects of scale compositions on oxidation resistance were studied further by analyses using X-ray diffraction （XRD） and scanning electron microscope （SEM）. It is found that the composite scale compounds of Cr203, a-Al2O3, SiO2 and FeCr2O4, with compact structure and tiny grains, shows complete oxidation resistance at 1,200℃. When the composite scale lacks a-Al2O3 or SiO2, it becomes weak in oxidation resistance with a loose structure. By the criterion of standard Gibbs formation free energy, the model of the nucleation and growth of the composite scale is established. The forming of the composite scale is the result of the competition of being oxidized and reduced between aluminum, silicon and the matrix metal elements of iron, chromium and nickel. The protection of the composite scale is analyzed essentially by electrical conductivity and strength properties.

Scale up and stability test for oxidative coupling of methane over Na_2WO_4-Mn/SiO_2 catalyst in a 200 ml fixed-bed reactor

The study of scale up for the oxidative coupling of methane （OCM） has been carried out in a 200 ml stainless steel fixed-bed reactor over a 5wt% Na2WO4-1.9wt% Mn/SiO2 （W-Mn/SiO2） catalyst. The effects of reaction conditions were investigated in detail. The results showed that, with increasing reaction temperature, the gas-phase reaction was enhanced and a significant amount of methane was converted into COx; with the CH4/O2 molar ratio of 5, the highest C2 （ethylene and ethane） yield of 25% was achieved; the presence of steam （as diluent） had a positive effect on the C2 selectivity and yield. Under lower methane gaseous hourly space velocity （GHSV）, higher selectivity and yield of C2 were obtained as the result of the decrease of released heat energy. In 100 h reaction time, the C2 selectivity of 66%-61% and C2 yield of 24.2%-25.4% were achieved by a single pass without any significant loss in catalytic performance.

Changes of Nitric Oxide and Its Relationship with Clinical Features,Intracranial Pressure and Outcome in Acute Head Injury

To investigate the content and dynamics of nitric oxide (NO) in the cerebrospinal fluid (CSF) of patients with acute head injury and to clarify the relationship of NO with clinical features and intracranial pressure (ICP) as well as outcomes, 38 adults with acute head injury were studied. Glasgow Coma Scale (GCS) obtained at admission and Glasgow Outcome Scale (GOS) 3 months after injury was assessed. ICP was surveyed via intraventricular catheter and lumbar puncture and CSF samples were obtained simultaneously. NO was determined with Griess reagents. Results showed that NO peak content in the head injury group was significantly higher than that of the control group. During dynamic research, no peak content of mildly injured cases and severely injured ones appeared in different time windows respectively. The peak value of NO was distinctly higher in the severe group than in the mild group. NO peak value of the raised ICP group was remarkably higher than that of the normal ICP group. The peak value of NO was considerately higher in the poor outcome group than in the good outcome group. When the content of NO was over 6. 5 μmol/L, the rate of poor outcome was increased. There existed a correlation between NO and GCS, ICP and GOS. It is concluded that the content of NO was increased in patients with acute head injury and the changes of NO had different time windows in severely injured patients and mildly injured ones. The more sever the injury, the higher the NO content; and the more serious the secondary brain injury and brain edema, the worse the outcomes. When NO is combined with GCS, GOS and ICP, it increases the accuracy of judgement to the degree of head injury and outcome.

Effect of Reduction on Bonding Interface of Hot-rolled Wear-resistant Steel BTW1/Q345R Cladding Plate

Wear-resistant cladding plates consisting of a substrate（Q345 R） and a clad layer（BTW1） were bonded through hot rolling at the temperature of 1 200 ℃ and a rolling speed of 0.5 m/s. The microhardness of the cladding plate was also tested after being heat treated. The microstructure evolution on the interface of BTW1/Q345 R sheets under various reduction rates was investigated with a scanning electron microscope（SEM） and EBSD. It is found that the micro-cracks and oxide films on the interface disappear when the reduction is 80%, whereas the maximum uniform diffusion distance reaches 10 μm. As a result, a wide range of metallurgical bonding layers forms, which indicates an improved combination between the BTW1 and the Q345 R. Additionally, it is discovered that the unbroken oxide films on the interface are composed of Mn, Si or Cr at the reductions of 50% and 65%. The SEM fractography of tensile specimen demonstrates that the BTW1 has significant dimple characteristics and possesses lower-sized dimples with the increment in reduction, suggesting that the toughness and bonding strength of the cladding plates would be improved by the increase of reduction. The results reveal that a high rolling reduction causes the interfacial oxide film broken and further forms a higher-sized composite metallurgical bonding interface. The peak microhardness is achieved near the interface.

HIGH TEMPERATURE OXIDATION AND STRUCTURE OF SCALE AND WHISKERS FOR Fe-Ni-Cr SEALING ALLOYS

The oxidation rate,the growth,morphology and structure of oxide scale and whiskers for Fe-Ni-Cr sealing alloys in H_2-H_2O atmosphere at high temperatures have been studied. The growth rate of scale is controlled by diffusion.The scale is composed of Cr_2O_3 and spinel(Fe,Mn)O·Cr_2O_3 and the oxide whisker,are spinel(Fe,Mn)O·Cr_2O_3.

Effects of Scale Composition on Oxidation Kinetics of Fe-based Superalloy

By oxidation weight gain method, four groups of Fe-based superalloys with different content of chromium, aluminium and silicon were tested at 1 200 ℃ for 500 hours. According to the oxidation weight gains, the oxidation kinetic curves were plotted, and the equations were regressed by least square method and non-linear curve fitting. The effects of different scale compositions on the morphology and oxidation kinetic law were studied further by analysis of X-ray diffraction （XRD） and scanning electron microscope （SEM）. It is found that the compounded scale is composed of Cr2O3, Al2O3, SiO2 and FeCr2O4, with compact structure and fine grains, possessing complete oxidation resistance at 1 200 ℃, and the oxidation kinetic curve follows the power function of y=axb （a0, 0b1）. When the compounded scale lacks Al2O3 or SiO2, it becomes weak in oxidation resistance, but the oxidation kinetic curve still follows the power function with bigger parameter b. When Cr2O3 is absent, the kinetic curve shows two parts： the slow adding of oxidation weight gains at the beginning and the ascending line in the end. Such scale loses oxidation resistance completely.

Crystal Growth Kinetics and Size Controls——Ⅰ.for Some Anode Active Oxides

RuO2,IrO2 and PdO are the most frequently employed active oxides in titanium anode coatings,so studies on the kinetics of their crystal-growth are important for anode material preparations.In this paper,the particle growths of RuO2,IrO2 and PdO with increased temperature were discussed.The least-squares method was used to fit the kinetic data.As a result,the two-stage phenomena are found in all three noble material systems.The linear regression equations are correct both for the first and second stages.It is suggested that based on the corresponding kinetics equation Ln D =-QL/kT ＋ a,the sizes of oxide particles can be controlled for the three noble oxides.

Cu enrichment behavior at steel-scale interface during high temperature oxidation of Cu containing steel

In order to suppress the surface cracking induced by Cu during reheating and hot rolling process,Cu enrichment and its migration at the steel-scale interface was investigated during heating of steel cast at temperatures between 1000℃and 1200℃in N_2-O_2 and N_7-H_2O atmospheres.For oxidation of Cu containing steel,Cu enriched phase was formed by the preferential oxidation of Fe and the enrichment and migration behavior of Cu depends on the oxidation temperature,steel chemistry and atmosphere condition.Ni in steel induced the formation of solid Cu and Ni enriched phase at steel/scale interface and in scale layer and the formation of uneven steel/scale interface, which suppresses the Cu enrichment because of extrusion of Cu enriched region before the formation of liquid phase.On the other hand,Sn addition promotes the liquid Cu formation at steel/scale interface and penetration into grain boundary of Cu enriched phase by decreasing solidus temperature and solubility limit.In addition,for oxidation at 1 200℃,the behavior of Cu at and around the steel-scale interface was found dependent to a large extent on morphology of the oxide scale formed during oxidation.At the early stage of oxidation,Cu-rich phase formed and accumulated at the steel scale interface under both O_2-N_2 and H_2O-N_2 atmospheres.As the oxidation proceeded,however,Cu enrichment at and its migration from the steel-scale interface were vastly different for different oxidizing atmospheres.In the case of O_2-N_2 oxidation,an oxide layer formed initially at the steel surface, but soon after a gap was developed at the steel-scale interface and grew in its size,which practically separated the scale from the steel substrate.The scale layer formed under this condition was porous.The Cu-rich phase initially formed at the interface was found migrating to the scale layer,leaving no Cu-rich phase at the interface.In the case of H_2O-N_2 oxidation,however,the scale layer formed was dense and tightly attached to the steel surface,and the Cu rich-phase continued to accumulate at the interface.Regarding the behavior of Cu-rich phase formed at the interface,it is proposed with experimental evidences that,when a gap forms at the steel-scale interface,it is the vaporization of Cu in the Cu-rich phase through the gap that brings Cu to the scale.