Experimental Study on Ammonia Co-Firing with Coal for Carbon Reduction in the Boiler of a 300-MW Coal-Fired Power Station

To reduce CO_(2) emissions from coal-fired power plants,the development of low-carbon or carbon-free fuel combustion technologies has become urgent.As a new zero-carbon fuel,ammonia(NH_(3))can be used to address the storage and transportation issues of hydrogen energy.Since it is not feasible to completely replace coal with ammonia in the short term,the development of ammonia-coal co-combustion technology at the current stage is a fast and feasible approach to reduce CO_(2) emissions from coal-fired power plants.This study focuses on modifying the boiler and installing two layers of eight pure-ammonia burners in a 300-MW coal-fired power plant to achieve ammonia-coal co-combustion at proportions ranging from 20%to 10%(by heat ratio)at loads of 180-to 300-MW,respectively.The results show that,during ammonia-coal co-combustion in a 300-MW coal-fired power plant,there was a more significant change in NO_(x) emissions at the furnace outlet compared with that under pure-coal combustion as the boiler oxygen levels varied.Moreover,ammonia burners located in the middle part of the main combustion zone exhibited a better high-temperature reduction performance than those located in the upper part of the main combustion zone.Under all ammonia co-combustion conditions,the NH_(3) concentration at the furnace outlet remained below 1 parts per million(ppm).Compared with that under pure-coal conditions,the thermal efficiency of the boiler slightly decreased(by 0.12%-0.38%)under different loads when ammonia co-combustion reached 15 t·h^(-1).Ammonia co-combustion in coal-fired power plants is a potentially feasible technology route for carbon reduction.

Environmental performance assessments of different methods of coal preparation for use in small-capacity boilers: experiment and theory

The purpose of this article is to receive environmental assessments of combustion of different types of coal fuel depending on the preparation(unscreened,size-graded,briquetted and heat-treated)in automated boilers and boilers with manual load-ing.The assessments were made on the basis of data obtained from experimental methods of coal preparation and calculated methods of determining the amount of pollutant and greenhouse gas emissions,as well as the mass of ash and slag waste.The main pollutants from coal combustion are calculated:particulate matter,benz(a)pyrene,nitrogen oxides,sulfur dioxide,carbon monoxide.Of the greenhouse gases carbon dioxide is calculated.As a result of conducted research it is shown that the simplest preliminary preparation(size-graded)of coal significantly improves combustion efficiency and environmental performance:emissions are reduced by 13%for hard coal and up to 20%for brown coal.The introduction of automated boil-ers with heat-treated coal in small boiler facilities allows to reduce emissions and ash and slag waste by 2-3 times.The best environmental indicators correspond to heat-treated lignite,which is characterized by the absence of sulfur dioxide emissions.

Sliding Mode Predictive Control of Main Steam Pressure in Coal-fired Power Plant Boiler

Since the combustion system of coal-fired boiler in thermal power plant is characterized as time varying, strongly coupled, and nonlinear, it is hard to achieve a satisfactory performance by the conventional proportional integral derivative (PID) control scheme. For the characteristics of the main steam pressure in coal-fired power plant boiler, the sliding mode control system with Smith predictive structure is proposed to look for performance and robustness improvement. First, internal model control (IMC) and Smith predictor (SP) is used to deal with the time delay, and sliding mode controller (SMCr) is designed to overcome the model mismatch. Simulation results show the effectiveness of the proposed controller compared with conventional ones.

Computational Study on Furnace Process in a Multi-burner Boiler of Pulverized Coal Fired Tangentially at Four Corners

Aiming at the optimization of the operation condition, a general numerical method for calculating pulverized coal combustion in a full scale furnace fired tangentially at four corners is adopted. “ k ε ” turbulence model is used for the gas phases and a stochastic approach based on the Lagrangian technique is used for particle phases. Two competing reactions model for the coal devolatilization and PDF (the probability density function) method for the combustion of the gas phases are employed. In the numerical simulations, assuming the air distribution of second port level is of pagoda, waist drum and uniform type. The results show that pagoda type air distribution is advantageous to ignition and smooth combustion of pulverized coal, and suitable to inferior coal combustion in practice. In the present furnace, the igniting distance at 1st and 3rd corner is longer than that at 2nd and 4th corner. The results from numerical calculations are in good agreement with those of observed in practice.

INTRODUCTION TO INCONEL ALLOY 740: AN ALLOY DESIGNED FOR SUPERHEATER TUBING IN COAL-FIRED ULTRA SUPERCRITICAL BOILERS

Chinese utilities as well as those worldwide are facing increased demand for additional electricity, reduced plant emissions and greater efficiency. To meet this challenge will require increasing boiler temperature, pressure and coal ash corrosion resistance of the materials of boiler construction of future coal-fired boilers. A new nickel-based tube alloy, INCONEL^R alloy 740, is described aiming at meeting this challenge. Emphasis will be on describing the alloy＇ s mechanical properties, coal-ash and steam corrosion resistance. Microstructural stability as a function of temperature and time is addressed as well as some of the early methodology em- ployed to arrive at the current chemical composition.

Two-stage numerical simulation for temperature profile in furnace of tangentially fired pulverized coal boiler

Considering the fact that the temperature distribution in furnace of a tangential fired pulverized coal boiler is difficult to be measured and monitored, two-stage numerical simulation method was put forward. First, multi-field coupling simulation in typical work conditions was carried out off-line with the software CFX-4.3, and then the expression of temperature profile varying with operating parameter was obtained. According to real-time operating parameters, the temperature at arbitrary point of the furnace can be calculated by using this expression. Thus the temperature profile can be shown on-line and monitoring for combustion state in the furnace is realized. The simul-(ation) model was checked by the parameters measured in an operating boiler, (DG130-9.8/540.) The maximum of relative error is less than 12% and the absolute error is less than 120℃, which shows that the proposed two-stage simulation method is reliable and able to satisfy the requirement of industrial application.

Feasibility Analysis on the Integrated Application of Solar Energy, Biogas, Coal-fired Boiler and Radiant Floor Heating for Rural Residence

The feasibility of adopting a balanced energy mix mode (domestic solar energy, biogas, coal-fired boiler and radiant floor heating) was proposed. Taking a typical rural residence in Zhengzhou City for example, the study through theoretical analysis and calculation showed that such a balanced energy mix is an economic way and efficient in saving energy and reducing air pollution, and elaborated the theoretical feasibility of popularizing such a heat supply mode in rural areas.

Equation of Radiation Heat Transfer in Multiple Combustion Boiler Furnace of Fluidized Bed and Pulverized Coal Firing

The equation for radiation heat transfer in a multiple combustion boiler furnace with nuidized bed and pulverized coal firing is derived from direct calculation of radiation heat transfer.

Development of 600 MW Class Coal Fired Boilers in China

This article introduces the present status anddevelopment of 600 MW class boilers in China. The statisticaldata indicate that most 600 MW generating units experiencedrelatively length" growing up" period. In this period, unitscould not operate stably , their unplanned outage times weremany and durations long, and availabilities low. On the basis oftesting and research and the summing-up of practice, it wasindicated slagging in the furnace, deviation of tine gas energy atthe exit of furnace, and overheating bursting of superheater andreheater etc, endangering the safety and economics ofoperation,main problems could be completely alleviated oravoided through design and type selection of boiler furnace andburners, coal characteristics and coal handling management,and optimization management of operation conditions etc.

Discussion on Selection of Pulverizer and Moisture of Pulverized Coal for Lignite Boilers

In China,the abrasion index and the free moisture are regarded as the criteria for determining whether the medium-speed pulverizer or the fan pulverizer could be selected.Based on comprehensive studies on foreign methods for choosing the pulverizing system for lignite boilers,it is suggested that the particle size of coal,the drying time,the drying temperature and the humidity should be taken into account when measuring the free moisture of lignite,and the total moisture could also be the principle for type selection of pulverizer for lignite boilers.Furthermore,the determination of pulverized-coal moisture has great influence on the running of pulverizing systems.The actual moisture of certain pulverized coals is compared with that calculated with different methods and a feasible method for determining the moisture of the pulverized coal is suggested.

Influence of Recirculated Flue Gas Distribution on Combustion and NOx Formation Characteristics in S-CO_(2) Coal-fired Boiler

Supercritical carbon dioxide(S-CO_(2))Brayton power cycle power generation technology,has attracted more and more scholars'attention in recent years because of its advantages of high efficiency and flexibility.Compared with conventional steam boilers,S-CO_(2) has different heat transfer characteristics,it is easy to cause the temperature of the cooling wall of the boiler to rise,which leads to higher combustion gas temperature in the furnace,higher NOX generation concentration.The adoption of flue gas recirculation has a significance impact on the combustion process of pulverized coal in the boiler,and it is the most effective ways to reduce the emission of NOX and the combustion temperature in the boiler.This paper takes 1000MW S-CO_(2) T-type coal-fired boiler as the research target to investigate the combustion and NOX generation characteristics of S-CO_(2) coal-fired boilers under flue gas recirculation condition,the influence of recirculated flue gas distribution along the furnace height on the characteristics of NOX formation and the combustion of pulverized coal.The results show that the recirculated flue gas distribution has the great impact on the concentration of NOX at the boiler outlet.When the bottom recirculation flue gas rate is gradually increased,the average temperature of the lower boiler decreases and the average temperature of the upper boiler increases slightly;The concentration of NOx at the furnace outlet increases.

System Performance and Pollution Emission of Biomass Gas Co-Firing in a Coal-Fired Boiler

To reduce greenhouse gases emission and increase the renewable energy utilization portion in the world, the biomass gasification coupled with a coal-fired boiler power generation system is studied. It is a challenge to achieve optimum performance for the coupled system. The models of biomass gasification coupled with co-firing of coal in a boiler have been established. A comparative study of three kinds of biomass (Food Rubbish, Straw and Wood Pellets) has been done. The syngas produced in a 10 t/h gasifier is fed to a 330 MWe coal-fired boiler for co-combustion, and the co-firing performances have been compared with pure coal combustion case under the conditions of constant boiler load. Results show that co-firing decreases the furnace combustion temperature and raises the flue gas temperature for Food Rubbish and Straw, while, flue gases temperature decrease in case of Wood Pellets. At the same time NOx and SOx emissions have reduced. The system efficiencies at constant load for Food Rubbish, Straw and Wood Pellets are 83.25%, 83.88% and 82.56% when the optimum conditions of gasification and co-firing process are guaranteed.

燃用高碱煤锅炉受热面结焦及其防治研究概述

以准东煤为代表的高碱煤虽储量巨大,但火电机组掺烧高碱煤过程中造成锅炉受热面结焦问题突出,不仅降低锅炉热效率,而且严重威胁机组安全、稳定、经济运行。为解决结焦技术难题,促进高碱煤掺烧利用,对燃用高碱煤锅炉受热面结焦及其防治研究进行了综述。截至目前,国内外围绕燃煤锅炉受热面结焦特征、结焦机理、影响因素、防治措施等已经开展了广泛研究并取得了丰硕的研究成果。在控制燃煤质量、改善锅炉结构、优化锅炉运行等措施基础上,在锅炉受热面制备涂层成为防治结焦的重要技术途径。在未来研究过程中,涂层在具备突出抗结焦性能的同时,须兼具优良的耐高温、抗腐蚀、耐磨损、导热性、热疲劳等综合性能,且具有良好的制备经济性、制备效率,特别是现场适用性。

大型燃煤锅炉中含Na/Cl/S组分的演变与受热面结渣倾向的数值模拟

提出了一种考虑煤中含Na/S/Cl组分多步释放、气相组分相互作用、气-固反应以及盐蒸气冷凝耦合灰颗粒黏附的结焦模型,以预测炉内受热面气态碱金属组分冷凝行为、受热面结焦风险以及炉膛出口Na/S/Cl组分分布特性。结果表明:炉膛出口气态含Na组分主要以NaO_(2)、NaCl、Na_(2)SO_(4)和NaOH形式存在;最上层燃烧器至分离燃尽风(SOFA)喷口区域、最下层燃烧器至冷灰斗转角区域的水冷壁结焦风险高;炉膛出口区域后屏过热器底部颗粒黏附位置相对集中,炉内辐射式过热器结焦速率远高于气态钠盐冷凝速率,对流受热面颗粒沉积速率约是钠盐蒸气冷凝速率的3~4倍。

燃煤机组锅炉负荷偏差分析模型与评价系统

“双碳”大背景下我国上网新能源装机发展十分迅速。为了加大电网对新能源发电的消纳,燃煤发电机组频繁参与深度调峰导致了机组实际负荷与自动发电控制(AGC)指令负荷出现较大偏差。针对这一技术难题,以锅炉及其辅助设备为对象,研究构建了锅炉机组本体及其辅助设备的实际出力模型、应有出力模型和最大出力模型,建立了用以分析评价锅炉机组负荷偏差原因及诊断与预警的分析评价系统,并将该系统在电厂中进行了验证。结果表明:该分析评价系统可有效地对锅炉及其辅助设备的出力故障进行早期预警和诊断,可有效提高机组运行的可靠性、安全性与经济性。

宽负荷下切圆燃煤锅炉H_(2)S分布特性的数值模拟

锅炉采用空气分级燃烧降低NO_(x)排放的同时也提高了主燃区H_(2)S体积分数。炉墙壁面过高的H_(2)S体积分数是加剧水冷壁高温腐蚀的重要因素。为保障新能源并网发电,大型燃煤机组灵活调峰的需求增加,不同负荷下的水冷壁近壁面H_(2)S分布特性值得关注。通过正交试验分析了切圆燃煤锅炉运行参数对水冷壁近壁面H_(2)S体积分数分布的影响。选取一台超临界600 MW切圆燃煤锅炉建立数值模型,设计L_(16)(4^(5))正交工况,覆盖100%BMCR、75%THA,50%THA以及35%BMCR四种负荷。建立了自定义SO_(x)生成模型以确定燃料硫的析出和转化路径,模型包含多表面反应子模型以描述焦炭与O_(2)/CO_(2)/H_(2)O等3种气体的异相反应,并确定焦炭气化反应消耗量占总消耗量的比例,进而对炉膛H_(2)S空间分布进行了模拟计算。研究表明,近壁面高体积分数H_(2)S区域主要位于投运燃烧器层中最下层燃烧器以下以及最上层燃烧器以上至SOFA层之间,烟气切圆沿炉膛高度增加逐渐增大是造成后一区域H_(2)S体积分数较高的重要原因。35%BMCR负荷下水冷壁重点区域的H_(2)S平均体积分数为364μL/L,明显低于其他负荷。锅炉运行参数对重点区域H_(2)S体积分数影响程度的排序为:锅炉负荷>一次风率>主燃区空气过量系数>假想切圆直径>燃烧器竖直摆角。

氨煤混燃气相中NO生成的化学反应动力学分析

氨煤混燃涉及复杂的化学反应过程,是否会加剧氮氧化物的生成是倍受关注的问题。通过化学反应动力学计算方法,研究了氨煤混合燃烧的气相反应中NO生成和还原的反应路径,以及不同因素对NO生成的影响。结果表明:温度T=1300℃、过量空气系数α=0.84时,相较于纯煤燃烧,掺氨比例为0.3时能够降低反应器出口NO体积分数96.5%,原因是此工况下氨分解产生大量的NH_(2)和NH等自由基,其还原反应的反应速率更快,从而使含N基元向N_(2)转化;T=1300℃下,掺氨比例为0.3时较为合适,此时反应器出口的NO和NH_(3)体积分数均较低;小比例掺氨燃烧会增大NO的生成速率和NH_(3)的分解速率,导致反应器出口NO体积分数增大,且温度越高,该现象越明显;α<1的还原性气氛和较低的温度(T≤1300℃)能够有效降低NO的排放。

燃煤锅炉温度场与高温腐蚀气氛场同步在线检测装置开发及应用

燃煤锅炉主燃区燃烧场的经济性、安全性和环保性对于智慧电厂建设具有重要意义。其中,水冷壁近壁面高温腐蚀H_(2)S和CO气体浓度的实时在线监测尤为重要。为实现燃煤锅炉主燃区温度场和高温腐蚀气氛场的同步测量,基于红外热成像原理,采用Optris-PI1M小型红外热成像仪,基于LabVIEW温度实时采集应用软件,在炉膛的观察口对主燃区温度场进行连续监测。以低成本1.5μm附近的通信波段激光器作为测量高温腐蚀气体H_(2)S和CO的激光光源,并结合波长调制光谱技术和频分复用技术,以实现H_(2)S和CO气体浓度的同步检测。线性度实验表明,其线性拟合相关系数为0.9995。将研制的同步检测仪器对某300 MW四角切圆燃煤锅炉的主燃区的温度场和气氛场进行了现场应用试验。现场测试结果表明,锅炉主燃区温度主要分布范围在1300~1400℃,最高温度达到了1500℃;同时得到了锅炉主燃区的H_(2)S和CO浓度分布,H_(2)S浓度在12~125 mg/m^(3)的范围内波动,而CO浓度主要分布在10%~20%之间,最高可达22%;炉内H_(2)S和CO的浓度呈正相关,氧气浓度保持在1%以下,由于厌氧燃烧会导致两种气体的含量增加,从而造成对水冷壁近壁面的高温腐蚀。

基于改进Node2vec算法的锅炉温度场分割方法研究

针对温度场特征参数差异引发的锅炉温度场分割准确性的问题,以维持温度场特征为目标,引入图结构表达场数据,通过改进Node2vec算法进行聚类分析,进而实现锅炉温度场的最佳分割。该方法基于多维度的特征信息对锅炉温度场实现分割,能够更准确地保留流场特征。在标准数据集上进行了实验验证,结果表明在具有多维度特征的数据集上,所提方法相比其他对比算法在分割效果方面有提升显著。最后将提出的方法用于分割电站锅炉温度场,结果表明该方法可以很好地捕捉温度场数据中的局部和全局特征,且结果具有较好的精确性。