Effect of pH Control with Acetic Acid/Sodium Acetate Buffer on Hot-water Extraction of Poplar Wood

Poplar wood chips were extracted in an acetic acid/sodium acetate(SA/AA)buffer solution at 180ºC for 60 minutes,with a solid-to-liquid ratio of 1:6,to investigate the effect of pH on the extraction performance in terms of chemical compositions of the extract.The pH was controlled by varying the concentrations of sodium acetate and acetic acid in the buffer system.Results showed that the SA/AA system could promote the dissolution of hemicellulose,obtaining more oligosaccharides and monosaccharides,and could also inhibit the excessive decomposition of monosaccharides.When extracting poplar wood chips in a SA/AA system of pH=3.7,the yield of oligosaccharides was the highest,while the contents of furfural and hydroxymethyl furfural decreased by 25%and 30%,respectively,compared to conventional water extraction systems.Moreover,the amount of lignin extracted in the S/AA process was also higher than that in a conventional hot water extraction process.

Effects of ultrasonic-assisted extraction on bioactive compounds,volatile flavors and antioxidant activities of vine tea water extracts

Background:Ampelopsis grossedentata,vine tea,which is the tea alternative beverages in China.In vine tea processing,a large amount of broken tea is produced,which has low commercial value.Methods:This study investigates the influence of different extraction methods(room temperature water extraction,boiling water extraction,ultrasonic-assisted room temperature water extraction,and ultrasonic-assisted boiling water extraction,referred to as room temperature water extraction(RE),boiling water extraction(BE),ultrasonic assistance at room temperature water extraction(URE),and ultrasonic assistance in boiling water extraction(UBE))on the yield,dihydromyricetin(DMY)content,free amino acid composition,volatile aroma components,and antioxidant properties of vine tea extracts.Results:A notable influence of extraction temperature on the yield of vine tea extracts(P<0.05),with BE yielding the highest at 43.13±0.26%,higher than that of RE(34.29±0.81%).Ultrasound-assisted extraction significantly increased the DMY content of the extracts(P<0.05),whereas DMY content in the RE extracts was 59.94±1.70%,that of URE reached 66.14±2.78%.Analysis revealed 17 amino acids,with L-serine and aspartic acid being the most abundant in the extracts,nevertheless ultrasound-assisted extraction reduced total free amino acid content.Gas chromatography-mass spectrometry analysis demonstrated an increase in the diversity and quantity of compounds in the vine tea water extracts obtained through ultrasonic-assisted extraction.Specifically,69 and 68 volatile compounds were found in URE and UBE extracts,which were higher than the number found in RE and BE extracts.In vitro,antioxidant activity assessments revealed varying antioxidant capacities among different extraction methods,with RE exhibiting the highest DPPH scavenging rate,URE leading in ABTS•+free radical scavenging,and BE demonstrating superior ferric ion reducing antioxidant activity.Conclusion:The findings suggest that extraction methods significantly influence the chemical composition and antioxidant properties of vine tea extracts.Ultrasonic-assisted extraction proved instrumental in elevating the DMY content in vine tea extracts,thereby enriching its flavor profile while maintaining its antioxidant properties.

Femtosecond laser small incision lenticule extraction on binocularity for myopia with glasses-free 3D technique

AIM:To evaluate the effect of femtosecond laser small incision lenticule extraction(SMILE)on the binocular visual function in myopic patients with glasses-free threedimensional(3D)technique.METHODS:Totally 50 myopic patients(39 females and 11 males)with SMILE were enrolled in this prospective study.The glasses-free 3D technique was used to evaluate the binocular visual function in these subjects including static stereopsis,dynamic stereopsis,foveal suppression,and binocular balance point of signal to noise ratio(s/n ratio).All subjects received measurements in 1d before operation,and 1d,1wk,and 1mo postoperatively.RESULTS:Both static and dynamic stereopsis showed no significant difference after SMILE.The foveal suppression improved significantly 1wk and 1mo after SMILE(P=0.005 and P=0.007 respectively).The binocular balance point of signal to noise ratio showed a significant improvement 1d,1wk and 1mo after SMILE for both eyes(P<0.001 for each eye respectively).CONCLUSION:Glasses-free 3D technique can be used to evaluate the effect of SMILE on the binocular visual function in myopic patients perceptively,and SMILE can improve both foveal suppression and binocular imbalance in these patients.

Optimization of lithium extraction solar pond in Zabuye Salt Lake: Theoretical calculation combined with field experiments

This research optimized the structure of lithium extraction solar ponds to enhance the crystallization rate and yield of Li_(2)CO_(3).Using the response surface methodology in Design-Expert 10.0.3,the authors conducted experiments to investigate the influence of four factors related to solar pond structure on the crystallization of Li_(2)CO_(3) and their pairwise interactions.Computational Fluid Dynamics(CFD)simulations of the flow field within the solar pond were performed using COMSOL Multiphysics software to compare temperature distributions before and after optimization.The results indicate that the optimal structure for lithium extraction from the Zabuye Salt Lake solar ponds includes UCZ(Upper Convective Zone)thickness of 53.63 cm,an LCZ(Lower Convective Zone)direct heating temperature of 57.39℃,a CO32−concentration of 32.21 g/L,and an added soda ash concentration of 6.52 g/L.Following this optimized pathway,the Li_(2)CO_(3) precipitation increased by 7.34% compared to the initial solar pond process,with a 33.33% improvement in lithium carbonate crystallization rate.This study demonstrates the feasibility of optimizing lithium extraction solar pond structures,offering a new approach for constructing such ponds in salt lakes.It provides valuable guidance for the efficient extraction of lithium resources from carbonate-type salt lake brines.

Nickel extraction from nickel laterites: Processes, resources, environment and cost

With the development of the new energy industry and the depletion of nickel sulfide ore resources,laterite nickel ore has become the main source of primary nickel,and nickel for power batteries has become a new growth point in consumption.This paper systematically summarizes the processes,parameters,products,recovery rates,environmental indicators,costs,advantages,disadvantages and the latest research progress of mainstream nickel extraction processes from laterite nickel ore.It also provides a comparative analysis of the environmental impact and economic efficiency of different nickel extraction processes.It is found that the current nickel extraction processes from laterite nickel ore globally for commercial production mainly include the RKEF process for producing ferronickel and the HPAL process for producing intermediate products.The former accounts for about 80%of laterite nickel ore production.Compared to each other,the investment cost per ton of nickel metal production capacity for the RKEF is about 43000$,with an operational cost of about 16000$per ton of nickel metal and a total nickel recovery rate of 77%–90%.Its products are mainly used in stainless steels.For the HPAL process,the investment cost per ton of nickel metal production capacity is about 56000$,with an operational cost of about 15000$per ton of nickel metal and a total nickel recovery rate of 83%–90%.Its products are mainly used in power batteries.The significant differences between the two lies in energy consumption and carbon emissions,with the RKEF being 2.18 and 2.37 times that of the HPAL,respectively.Although the use of clean energy can greatly reduce the operational cost and environmental impact of RKEF,if RKEF is converted to producing high Ni matte,its economic and environmental performance still cannot match that of the HPAL and oxygen-enriched side-blown processes.Therefore,it can be inferred that with the increasing demand for nickel in power batteries,HPAL and oxygen-enriched side blowing processes will play a greater role in laterite nickel extraction.

Effect of hot-water extraction of sugar maple on organosolv delignification and lignin recovery

This paper reported a gradual disassembly of the chemical components of hardwood,starting with hot-water extraction(HWE)for the removal of hemicelluloses,followed by organosolv delignification to remove the lignin.Under mild acid conditions,in addition to hemicelluloses,lower molecular weight lignin fractions were removed(~15%of the total lignin)in the HWE pre-treatment;also,the cleavage of the acid-labile lignin-carbohydrate bond took place to some extent.As a result,the HWE pretreatment promoted the subsequent delignification process and facilitated the lignin recovery from the spent liquor,in terms of higher delignification efficiency and higher purity of the lignin recovered from the spent liquor.The effects of the HWE pre-treatment prior to the delignification process were investigated in this study for both the oxygen-pressurized acetone-water(AWO)and the ALCELL processes,with focuses on the delignification efficiency and the properties of the lignin recovered from the process spent liquor.

A Review on Sources,Extractions and Analysis Methods of a Sustainable Biomaterial:Tannins

Condensed and hydrolysable tannins are non-toxic natural polyphenols that are a commercial commodity industrialized for tanning hides to obtain leather and for a growing number of other industrial applications mainly to substitute petroleum-based products.They are a definite class of sustainable materials of the forestry industry.They have been in operation for hundreds of years to manufacture leather and now for a growing number of applications in a variety of other industries,such as wood adhesives,metal coating,pharmaceutical/medical applications and several others.This review presents the main sources,either already or potentially commercial of this forestry by-materials,their industrial and laboratory extraction systems,their systems of analysis with their advantages and drawbacks,be these methods so simple to even appear primitive but nonetheless of proven effectiveness,or very modern and instrumental.It constitutes a basic but essential summary of what is necessary to know of these sustainable materials.In doing so,the review highlights some of the main challenges that remain to be addressed to deliver the quality and economics of tannin supply necessary to fulfill the industrial production requirements for some materials-based uses.

Changes in Soil Hot-Water Extractable C,N and P Fractions During Vegetative Restoration in Zhifanggou Watershed on the Loess Plateau

The study was conducted in Zhifanggou Watershed,Shaanxi Province,China,to evaluate the effect of different vegetation types on hot-water extractable C,N and P fractions,with the aim to determine whether hot-water extractable fractions could be used as indicators of soil quality change in Loess Plateau.The six vegetation types established in 1975 were（i） Robinia pseudoacacia L.,（ii） Caragana korshinkii Kom.,（iii） Pinus tabulaeformis Carr.,（iv） P.tabulaeformis-Amorpha fruticosa L.,（v） R.pseudoacacia-A.fruticosa,and（vi） grassland.A cropped hillslope plot and a Platycladus orientalis L.native forest plot were used as references.The results indicated that the conversion of native forest to cropland resulted in a significant decline in the hot-water extractable C,N and P fractions.Hot-water extractable C,N,and P increased when cultivated land was revegetated,but after 30 years the amount of hot-water extractable C,N,and P in revegetated fields was still much lower compared to native forest.Hot-water extractable fractions increased more under mixed-forest than under pure-forest stands.Furthermore,there was a significant correlation between the hot-water extractable fractions and soil chemical and microbiological properties.The results showed that hot-water extractable fractions could be used as indicators of soil quality change on the Loess Plateau.

Feature extraction for machine learning-based intrusion detection in IoT networks

A large number of network security breaches in IoT networks have demonstrated the unreliability of current Network Intrusion Detection Systems(NIDSs).Consequently,network interruptions and loss of sensitive data have occurred,which led to an active research area for improving NIDS technologies.In an analysis of related works,it was observed that most researchers aim to obtain better classification results by using a set of untried combinations of Feature Reduction(FR)and Machine Learning(ML)techniques on NIDS datasets.However,these datasets are different in feature sets,attack types,and network design.Therefore,this paper aims to discover whether these techniques can be generalised across various datasets.Six ML models are utilised:a Deep Feed Forward(DFF),Convolutional Neural Network(CNN),Recurrent Neural Network(RNN),Decision Tree(DT),Logistic Regression(LR),and Naive Bayes(NB).The accuracy of three Feature Extraction(FE)algorithms is detected;Principal Component Analysis(PCA),Auto-encoder(AE),and Linear Discriminant Analysis(LDA),are evaluated using three benchmark datasets:UNSW-NB15,ToN-IoT and CSE-CIC-IDS2018.Although PCA and AE algorithms have been widely used,the determination of their optimal number of extracted dimensions has been overlooked.The results indicate that no clear FE method or ML model can achieve the best scores for all datasets.The optimal number of extracted dimensions has been identified for each dataset,and LDA degrades the performance of the ML models on two datasets.The variance is used to analyse the extracted dimensions of LDA and PCA.Finally,this paper concludes that the choice of datasets significantly alters the performance of the applied techniques.We believe that a universal(benchmark)feature set is needed to facilitate further advancement and progress of research in this field.

Experimental investigation on coal pore-fracture variation and fractal characteristics synergistically affected by solvents for improving clean gas extraction

Chemical solvents instead of pure water being as hydraulic fracturing fluid could effectively increase permeability and improve clean methane extraction efficiency.However,pore-fracture variation features of lean coal synergistically affected by solvents have not been fully understood.Ultrasonic testing,nuclear magnetic resonance analysis,liquid phase mass spectrometry was adopted to comprehensively analyze pore-fracture change characteristics of lean coal treated by combined solvent(NMP and CS_(2)).Meanwhile,quantitative characterization of above changing properties was conducted using geometric fractal theory.Relationship model between permeability,fractal dimension and porosity were established.Results indicate that the end face fractures of coal are well developed after CS2and combined solvent treatments,of which,end face box-counting fractal dimensions range from 1.1227 to 1.4767.Maximum decreases in ultrasonic longitudinal wave velocity of coal affected by NMP,CS_(2)and combined solvent are 2.700%,20.521%,22.454%,respectively.Solvent treatments could lead to increasing amount of both mesopores and macropores.Decrease ratio of fractal dimension Dsis 0.259%–2.159%,while permeability increases ratio of NMR ranges from 0.1904 to 6.4486.Meanwhile,combined solvent could dissolve coal polar and non-polar small molecules and expand flow space.Results could provide reference for solvent selection and parameter optimization of permeability-enhancement technology.

Preferentially selective extraction of lithium from spent LiCoO_(2)cathodes by medium-temperature carbon reduction roasting

Lithium recovery from spent lithium-ion batteries(LIBs)have attracted extensive attention due to the skyrocketing price of lithium.The medium-temperature carbon reduction roasting was proposed to preferential selective extraction of lithium from spent Li-CoO_(2)(LCO)cathodes to overcome the incomplete recovery and loss of lithium during the recycling process.The LCO layered structure was destroyed and lithium was completely converted into water-soluble Li2CO_(3)under a suitable temperature to control the reduced state of the cobalt oxide.The Co metal agglomerates generated during medium-temperature carbon reduction roasting were broken by wet grinding and ultrasonic crushing to release the entrained lithium.The results showed that 99.10%of the whole lithium could be recovered as Li2CO_(3)with a purity of 99.55%.This work provided a new perspective on the preferentially selective extraction of lithium from spent lithium batteries.

Automatic Extraction Method of 3D Feature Guidelines for Complex Cultural Relic Surfaces Based on Point Cloud

Cultural relics line graphic serves as a crucial form of traditional artifact information documentation,which is a simple and intuitive product with low cost of displaying compared with 3D models.Dimensionality reduction is undoubtedly necessary for line drawings.However,most existing methods for artifact drawing rely on the principles of orthographic projection that always cannot avoid angle occlusion and data overlapping while the surface of cultural relics is complex.Therefore,conformal mapping was introduced as a dimensionality reduction way to compensate for the limitation of orthographic projection.Based on the given criteria for assessing surface complexity,this paper proposed a three-dimensional feature guideline extraction method for complex cultural relic surfaces.A 2D and 3D combined factor that measured the importance of points on describing surface features,vertex weight,was designed.Then the selection threshold for feature guideline extraction was determined based on the differences between vertex weight and shape index distributions.The feasibility and stability were verified through experiments conducted on real cultural relic surface data.Results demonstrated the ability of the method to address the challenges associated with the automatic generation of line drawings for complex surfaces.The extraction method and the obtained results will be useful for line graphic drawing,displaying and propaganda of cultural relics.

Intelligent extraction of road cracks based on vehicle laser point cloud and panoramic sequence images

In light of the limited efficacy of conventional methods for identifying pavement cracks and the absence of comprehensive depth and location data in two-dimensional photographs,this study presents an intelligent strategy for extracting road cracks.This methodology involves the integration of laser point cloud data obtained from a vehicle-mounted system and a panoramic sequence of images.The study employs a vehicle-mounted LiDAR measurement system to acquire laser point cloud and panoramic sequence image data simultaneously.A convolutional neural network is utilized to extract cracks from the panoramic sequence image.The extracted sequence image is then aligned with the laser point cloud,enabling the assignment of RGB information to the vehicle-mounted three dimensional(3D)point cloud and location information to the two dimensional(2D)panoramic image.Additionally,a threshold value is set based on the crack elevation change to extract the aligned roadway point cloud.The three-dimensional data pertaining to the cracks can be acquired.The experimental findings demonstrate that the use of convolutional neural networks has yielded noteworthy outcomes in the extraction of road cracks.The utilization of point cloud and image alignment techniques enables the extraction of precise location data pertaining to road cracks.This approach exhibits superior accuracy when compared to conventional methods.Moreover,it facilitates rapid and accurate identification and localization of road cracks,thereby playing a crucial role in ensuring road maintenance and traffic safety.Consequently,this technique finds extensive application in the domains of intelligent transportation and urbanization development.The technology exhibits significant promise for use in the domains of intelligent transportation and city development.

Effects of conductive agent type on lithium extraction from salt lake brine with LiFePO_(4) electrodes

Electrochemical lithium extraction from salt lakes is an effective strategy for obtaining lithium at a low cost.Nevertheless,the elevated Mg:Li ratio and the presence of numerous coexisting ions in salt lake brines give rise to challenges,such as prolonged lithium extraction periods,diminished lithium extraction efficiency,and considerable environmental pollution.In this work,Li FePO4(LFP)served as the electrode material for electrochemical lithium extraction.The conductive network in the LFP electrode was optimized by adjusting the type of conductive agent.This approach resulted in high lithium extraction efficiency and extended cycle life.When the single conductive agent of acetylene black(AB)or multiwalled carbon nanotubes(MWCNTs)was replaced with the mixed conductive agent of AB/MWCNTs,the average diffusion coefficient of Li+in the electrode increased from 2.35×10^(-9)or 1.77×10^(-9)to 4.21×10^(-9)cm^(2)·s^(-1).At the current density of 20 mA·g^(-1),the average lithium extraction capacity per gram of LFP electrode increased from 30.36 mg with the single conductive agent(AB)to 35.62 mg with the mixed conductive agent(AB/MWCNTs).When the mixed conductive agent was used,the capacity retention of the electrode after 30 cycles reached 82.9%,which was considerably higher than the capacity retention of 65.8%obtained when the single AB was utilized.Meanwhile,the electrode with mixed conductive agent of AB/MWCNTs provided good cycling performance.When the conductive agent content decreased or the loading capacity increased,the electrode containing the mixed conductive agent continued to show excellent electrochemical performance.Furthermore,a self-designed,highly efficient,continuous lithium extraction device was constructed.The electrode utilizing the AB/MWCNT mixed conductive agent maintained excellent adsorption capacity and cycling performance in this device.This work provides a new perspective for the electrochemical extraction of lithium using LFP electrodes.

Influence of the Extraction Process on the Characteristics of Romanian Mountain Walnut Oil

The objective of this work is to extract walnut oil using various processes in order to compare the influence on the nature of the components extracted, and thus identify the areas of potential use. We carried out the extractions by mechanical process, thanks to a press in reduced model provided with a worm. We obtained cold extracted oil whose characteristics slightly diverge from extra virgin oil found in shops in Romania, but its composition is similar. We were also able to extract by chemical process using two methods, Folch and Soxhlet. Commercially available table walnut oils are only cold extracted to avoid the presence of solvents. Those are difficult to remove and strongly oxidize the oil. Currently, consumers appreciate walnut oil for its taste and nutritional qualities. In nutrition, this oil is put forward for its composition rich in polyunsaturated fatty acids, which are needed for human body. Food supplements made from walnut oil are available today. For the moment, this is the only use of walnut oil. Indeed, there are some studies on other fields of application, but they remain in the field of research and nothing has yet been commercialized. In this present study, we compared the chemical and physical properties of cold-extracted oil with the solvent extraction of walnut kernel originating from the mountain region of Rumania. The cold extracted oil has a high content of polyunsaturated fatty acids (63%) and monounsaturated fatty acids (30%), a very low level of saturated fatty acid (7%) and no content of linolenic acid. The Soxhlet and Folch methods produced slightly different oils with increased amounts of minor components, which changes their characteristic. Even when solvent-extracted oils do not meet the standard criteria imposed by the Codex Alimentarius, they offer a possible use in the fields of food, cosmetics industries and biomedicine.

Development of a Simple Extraction Method for Tetracycline Analogues from Bovine Milk

Tetracycline and analogues are among the most used antibiotics in the dairy industry. Besides the therapeutic uses, tetracyclines are often incorporated into livestock feed as growth promoters. A considerable amount of antibiotics is released unaltered through milk from dairy animals. The presence of antibiotic residues in milk and their subsequent consumption can lead to potential health impacts, including cancer, hypersensitivity reactions, and the development of antibiotic resistance. Thus, it is important to monitor residual levels of tetracyclines in milk. The purpose of this study is to develop a quick and simple method for simultaneously extracting five tetracycline analogues from bovine milk. Specifically, five tetracycline analogues: Chlortetracycline (CTC), demeclocycline (DEM), doxycycline (DC), minocycline (MC), and tetracycline (TC) were simultaneously extracted from milk using trifluoroacetic acid. Subsequently, the extracted analogues were separated by reverse-phase high-performance liquid chromatography (RP-HPLC) and detected at 355 nm using UV/Vis. Calibration curves for all five tetracycline analogues show excellent linearity (r2 value > 0.99). Percent recovery for MC, TC, DEM, CTC, and DC were: 31.88%, 96.91%, 151.29, 99.20%, and 85.58% respectively. The developed extraction method has good precision (RSD < 9.9% for 4 of the 5 analogues). The developed method with minimal sample preparation and pretreatment has the potential to serve as an initial screening test.

A comprehensive review of existing corpora and methods for creating annotated corpora for event extraction tasks

Purpose:The purpose of this study is to serve as a comprehensive review of the existing annotated corpora.This review study aims to provide information on the existing annotated corpora for event extraction,which are limited but essential for training and improving the existing event extraction algorithms.In addition to the primary goal of this study,it provides guidelines for preparing an annotated corpus and suggests suitable tools for the annotation task.Design/methodology/approach:This study employs an analytical approach to examine available corpus that is suitable for event extraction tasks.It offers an in-depth analysis of existing event extraction corpora and provides systematic guidelines for researchers to develop accurate,high-quality corpora.This ensures the reliability of the created corpus and its suitability for training machine learning algorithms.Findings:Our exploration reveals a scarcity of annotated corpora for event extraction tasks.In particular,the English corpora are mainly focused on the biomedical and general domains.Despite the issue of annotated corpora scarcity,there are several high-quality corpora available and widely used as benchmark datasets.However,access to some of these corpora might be limited owing to closed-access policies or discontinued maintenance after being initially released,rendering them inaccessible owing to broken links.Therefore,this study documents the available corpora for event extraction tasks.Research limitations:Our study focuses only on well-known corpora available in English and Chinese.Nevertheless,this study places a strong emphasis on the English corpora due to its status as a global lingua franca,making it widely understood compared to other languages.Practical implications:We genuinely believe that this study provides valuable knowledge that can serve as a guiding framework for preparing and accurately annotating events from text corpora.It provides comprehensive guidelines for researchers to improve the quality of corpus annotations,especially for event extraction tasks across various domains.Originality/value:This study comprehensively compiled information on the existing annotated corpora for event extraction tasks and provided preparation guidelines.

A Joint Entity Relation Extraction Model Based on Relation Semantic Template Automatically Constructed

The joint entity relation extraction model which integrates the semantic information of relation is favored by relevant researchers because of its effectiveness in solving the overlapping of entities,and the method of defining the semantic template of relation manually is particularly prominent in the extraction effect because it can obtain the deep semantic information of relation.However,this method has some problems,such as relying on expert experience and poor portability.Inspired by the rule-based entity relation extraction method,this paper proposes a joint entity relation extraction model based on a relation semantic template automatically constructed,which is abbreviated as RSTAC.This model refines the extraction rules of relation semantic templates from relation corpus through dependency parsing and realizes the automatic construction of relation semantic templates.Based on the relation semantic template,the process of relation classification and triplet extraction is constrained,and finally,the entity relation triplet is obtained.The experimental results on the three major Chinese datasets of DuIE,SanWen,and FinRE showthat the RSTAC model successfully obtains rich deep semantics of relation,improves the extraction effect of entity relation triples,and the F1 scores are increased by an average of 0.96% compared with classical joint extraction models such as CasRel,TPLinker,and RFBFN.

A Case of Vasovagal Syncope Induced by Tooth Extraction

Background: Vasovagal syncope (VVS) is a neurogenic reflex-mediated fainting episode characterized by sudden, transient, and self-limiting symptoms. While VVS accounts for a significant portion (around 60%) of emergent medical events in dental practice, it remains an underrecognized condition among dental professionals, often misdiagnosed as hypoglycemia, conversion disorder, or epilepsy. This case report describes a VVS episode induced by tooth extraction, aiming to improve dental clinicians’ awareness and diagnostic approach to VVS. Case Presentation: A 35-year-old female visited the dental department in April 2022 with a two-year history of food impaction in the upper right molar. Examination revealed an elongated, discolored, and tender tooth 18, lacking proper occlusion with the opposing tooth. After confirming no contraindications, the tooth was extracted using a minimally invasive technique. Following the procedure, the patient experienced dizziness upon standing;her blood pressure was 69/47 mmHg, and her heart rate was 65 bpm. The nursing staff assisted her to sit as she showed limb weakness, closed eyes, and briefly lost consciousness. Oxygen was administered, and her blood glucose was 6.5. Blood pressure later improved to 124/78 mmHg, with a pulse of 62 bpm. Oral glucose was given, which she vomited, and emergency services were called. Upon arrival, the patient was alert and cooperative. Neurology consultation and imaging (MRI, MRA, and DWI) ruled out cerebral infarction, initially diagnosing a conversion disorder. A subsequent tilt-table test, including sublingual nitroglycerin, induced a marked blood pressure drop and symptoms confirming a diagnosis of vasovagal syncope (VVS). Conclusions: This case shows that preoperative anxiety, fear, and prolonged waiting can trigger vasovagal reflex during tooth extraction, especially in patients with anxiety or cardiac arrhythmias. For such patients, preoperative precautions and intraoperative cardiac monitoring are advised. In cases of VVS, quick actions like monitoring blood pressure, placing the patient in a supine position, providing oxygen, and administering IV fluids or medications like atropine, if necessary, can help stabilize the patient.

Development of Extraction and Detection Method for a Chemotherapeutic Drug with Phenytoin in Biological Samples

Dexamethasone is classified as a corticosteroid and is commonly used among cancer patients to decrease the amount of swelling around the tumor. Among patients with cancer, in particular brain tumors, seizures can become a daily routine in their everyday lives. To counteract the seizures, an antiepileptic drug such as phenytoin is administered to act as an anticonvulsant. Phenytoin and dexamethasone are frequently administrated concurrently to brain cancer patients. A previous study has shown that phenytoin serum concentration decreases when administrated concurrently with dexamethasone. Thus, it is important to monitor the concentration of these two drugs in biological samples to ensure that the proper dosages are administrated to the patients. This study aims to develop an effective extraction and detection method for dexamethasone and phenytoin. A reverse-phase high-performance liquid chromatography (HPLC) method with UV/Vis detection has been developed to separate phenytoin and dexamethasone at 219 nm and 241 nm respectively from urine samples. The mobile phase consists of a mixture of 0.01 M KH2PO4, acetonitrile, and methanol adjusted to pH 5.6 (48:32:20) and is pumped at a flow rate of 1.0 mL/min. Calibration curves were prepared for phenytoin and dexamethasone (r2 > 0.99). An efficient solid-phase extraction (SPE) method for the extraction of dexamethasone and phenytoin from urine samples was developed with the use of C-18 cartridges. The percent recovery for phenytoin and dexamethasone is 95.4% (RSD = 1.15%) and 81.1% (RSD = 3.56%) respectively.