To solve the low efficiency of electric excitation claw-pole synchronous generator（EECPSG） and regulate the magnetic field of permanent magnet （PM） claw-pole synchronous generator（PMCPSG）, a novel hybrid excitat...To solve the low efficiency of electric excitation claw-pole synchronous generator（EECPSG） and regulate the magnetic field of permanent magnet （PM） claw-pole synchronous generator（PMCPSG）, a novel hybrid excitation claw-pole synchronous generator （HECPSG）with magnetic circuit series connection is proposed. Through the simulation study on the generator using the calculation method for magnetic circuit and 3-D finite element method （FEA）, the appropriate magnet thickness and the number of pole-pairs for the proposed generator are determined. Its off-loading characteristics, load characteristics, and regulation behaviors are investigated. The study shows that the appropriate number of pole-pairs in HECPSG with series magnetic circuits is two, and there exists an optimum magnet thickness. Compared to EECPSG, HECPSG realizes dual-directional control to the excitation current. Moreover, the generator can adjust the output voltage and keep the output voltage stable in a broad load range. Under the condition of same parametes, the motor has higer air-gap flux density and power density.展开更多
With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying micr...With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying microstructures has grown significantly.However,a critical challenge is encountered in the design of these structures–the absence of robust interface connections between adjacent microstructures,potentially resulting in diminished efficiency or macroscopic failure.A Hybrid Level Set Method(HLSM)is proposed,specifically designed to enhance connectivity among non-uniform microstructures,contributing to the design of functionally graded cellular structures.The HLSM introduces a pioneering algorithm for effectively blending heterogeneous microstructure interfaces.Initially,an interpolation algorithm is presented to construct transition microstructures seamlessly connected on both sides.Subsequently,the algorithm enables the morphing of non-uniform unit cells to seamlessly adapt to interconnected adjacent microstructures.The method,seamlessly integrated into a multi-scale topology optimization framework using the level set method,exhibits its efficacy through numerical examples,showcasing its prowess in optimizing 2D and 3D functionally graded materials(FGM)and multi-scale topology optimization.In essence,the pressing issue of interface connections in complex structure design is not only addressed but also a robust methodology is introduced,substantiated by numerical evidence,advancing optimization capabilities in the realm of functionally graded materials and cellular structures.展开更多
In order to solve negative phase sequence problem of V connection transformer in the high speed and heavy haul electrical railway of China, the hybrid compensative co-phase traction power supply system which based on ...In order to solve negative phase sequence problem of V connection transformer in the high speed and heavy haul electrical railway of China, the hybrid compensative co-phase traction power supply system which based on passive and active compensation is proposed. Firstly, There construction and capacity distribution are analyzed, and the compensation current of active equipment is gave;Second, the feature of the hybrid compensative schemes are discussed. In the end, the related simulation results have confirmed the effectiveness of the compensation schemes in this paper.展开更多
Beam-column or beam-wall connections are an important problem in high-rise buildings. In this study, based on the analysis of an example structure, an analytical model for design of the semi-rigid connections between ...Beam-column or beam-wall connections are an important problem in high-rise buildings. In this study, based on the analysis of an example structure, an analytical model for design of the semi-rigid connections between steel beams and RC walls in high-rise hybrid buildings is proposed. Also, the mechanical characteristics of these connections subjected to low-reversed cyclic loading are investigated through comparison of experimental results from three semi-rigid connections and two rigid connections. Moreover, some latent problems for design of these connections as well as the corresponding solutions are discussed. The results from the experiments and analyses indicate that semi-rigid connections exhibit satisfactory capacity and seismic performance, and the proposed design can be used in practice.展开更多
In this work,we present a feasibility study for a new hybrid power plant(PV-Wind-Diesel-Storage)directly connected to the electrical grid.Several simulations are performed to verify the performance of the hybrid syste...In this work,we present a feasibility study for a new hybrid power plant(PV-Wind-Diesel-Storage)directly connected to the electrical grid.Several simulations are performed to verify the performance of the hybrid system under different scenarios using real meteorological data.It is shown that the performances of the hybrid system connected to the electrical network depend obviously on the available energy resources and constraints because the renewable energies are intermittent.In addition,the price of the kWh of electricity supplied by the hybrid system is determined,which amounts to$0.209/kWh,which is very cost effective and satisfactory for the considered sample conditions(Comoros Island).展开更多
This research paper proposes a single phase fifteen level inverter for a grid connected PV system.The proposed inverter is also called cascaded asymmetric multilevel inverter.By adopting appropriate hybrid modulation ...This research paper proposes a single phase fifteen level inverter for a grid connected PV system.The proposed inverter is also called cascaded asymmetric multilevel inverter.By adopting appropriate hybrid modulation technique improved output voltage is obtained with minimum number of power electronic switches.By reducing the number of gate triggering circuits of the switches,the size and power consumption of the driving circuits can be reduced.The total harmonic distortion of the output of the inverter is improved by this inverter.The proposed inverter developed by cascading a full bridge inverter with modified H bridge multilevel inverter.The validity of the proposed system is verified through MATLAB simulations.展开更多
In this paper, we show that there exists a twisted duality symmetry between the Maurer-Cartan equations and the equations of motion in the hybrid formalism for the type liB superstring in an AdS2 ×S2 background w...In this paper, we show that there exists a twisted duality symmetry between the Maurer-Cartan equations and the equations of motion in the hybrid formalism for the type liB superstring in an AdS2 ×S2 background with Ramond-Ramond flux. As a result, from the twisted duality transformation, we construct the Lax connection with the spectral parameter, which ensures the integrability of the system.展开更多
结合钢筋混凝土结构和钢结构的优势,设计一种型钢-螺栓-后浇混凝土装配式剪力墙型钢混合连接。基于ABAQUS有限元软件建立混合连接的剪力墙模型,探究低周往复荷载作用下该混合连接预制剪力墙的受力性能,主要分析模型的破坏形态、受力机...结合钢筋混凝土结构和钢结构的优势,设计一种型钢-螺栓-后浇混凝土装配式剪力墙型钢混合连接。基于ABAQUS有限元软件建立混合连接的剪力墙模型,探究低周往复荷载作用下该混合连接预制剪力墙的受力性能,主要分析模型的破坏形态、受力机制、变形曲线、特征承载力等,并扩展分析了材料强度、轴压比、连接件数量、型钢截面高度等参数对模型受力性能影响。结果表明:装配式剪力墙破坏形态为压弯破坏,破坏时钢连接件仍保持完整,符合“强连接,弱墙肢”的基本设计理念;装配式剪力墙具有较好的承载力、延性和刚度;轴压比对结构承载力影响显著,型钢混合连接间距的增大能有效提升剪力墙延性。建立了型钢混合连接抗剪需求承载力计算模型和公式,并与国内外规范计算值对比分析,公式计算值和BS EN 1992欧洲规范计算值分别与模拟值的误差在15%和20%以内,均可用于型钢混合连接剪力墙竖缝受剪承载力设计参考。展开更多
基金Supported by the National Natural Science Foundation of China(50337030)the Natural Science Foundation of Shanghai(08ZR1408600)the Natural Science Foundation of Shanghai Dianji University(08C410)~~
文摘To solve the low efficiency of electric excitation claw-pole synchronous generator（EECPSG） and regulate the magnetic field of permanent magnet （PM） claw-pole synchronous generator（PMCPSG）, a novel hybrid excitation claw-pole synchronous generator （HECPSG）with magnetic circuit series connection is proposed. Through the simulation study on the generator using the calculation method for magnetic circuit and 3-D finite element method （FEA）, the appropriate magnet thickness and the number of pole-pairs for the proposed generator are determined. Its off-loading characteristics, load characteristics, and regulation behaviors are investigated. The study shows that the appropriate number of pole-pairs in HECPSG with series magnetic circuits is two, and there exists an optimum magnet thickness. Compared to EECPSG, HECPSG realizes dual-directional control to the excitation current. Moreover, the generator can adjust the output voltage and keep the output voltage stable in a broad load range. Under the condition of same parametes, the motor has higer air-gap flux density and power density.
基金the National Key Research and Development Program of China(Grant Number 2021YFB1714600)the National Natural Science Foundation of China(Grant Number 52075195)the Fundamental Research Funds for the Central Universities,China through Program No.2172019kfyXJJS078.
文摘With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying microstructures has grown significantly.However,a critical challenge is encountered in the design of these structures–the absence of robust interface connections between adjacent microstructures,potentially resulting in diminished efficiency or macroscopic failure.A Hybrid Level Set Method(HLSM)is proposed,specifically designed to enhance connectivity among non-uniform microstructures,contributing to the design of functionally graded cellular structures.The HLSM introduces a pioneering algorithm for effectively blending heterogeneous microstructure interfaces.Initially,an interpolation algorithm is presented to construct transition microstructures seamlessly connected on both sides.Subsequently,the algorithm enables the morphing of non-uniform unit cells to seamlessly adapt to interconnected adjacent microstructures.The method,seamlessly integrated into a multi-scale topology optimization framework using the level set method,exhibits its efficacy through numerical examples,showcasing its prowess in optimizing 2D and 3D functionally graded materials(FGM)and multi-scale topology optimization.In essence,the pressing issue of interface connections in complex structure design is not only addressed but also a robust methodology is introduced,substantiated by numerical evidence,advancing optimization capabilities in the realm of functionally graded materials and cellular structures.
文摘In order to solve negative phase sequence problem of V connection transformer in the high speed and heavy haul electrical railway of China, the hybrid compensative co-phase traction power supply system which based on passive and active compensation is proposed. Firstly, There construction and capacity distribution are analyzed, and the compensation current of active equipment is gave;Second, the feature of the hybrid compensative schemes are discussed. In the end, the related simulation results have confirmed the effectiveness of the compensation schemes in this paper.
基金National Natural Science Foundation of China Under Grant No. 50025821
文摘Beam-column or beam-wall connections are an important problem in high-rise buildings. In this study, based on the analysis of an example structure, an analytical model for design of the semi-rigid connections between steel beams and RC walls in high-rise hybrid buildings is proposed. Also, the mechanical characteristics of these connections subjected to low-reversed cyclic loading are investigated through comparison of experimental results from three semi-rigid connections and two rigid connections. Moreover, some latent problems for design of these connections as well as the corresponding solutions are discussed. The results from the experiments and analyses indicate that semi-rigid connections exhibit satisfactory capacity and seismic performance, and the proposed design can be used in practice.
文摘In this work,we present a feasibility study for a new hybrid power plant(PV-Wind-Diesel-Storage)directly connected to the electrical grid.Several simulations are performed to verify the performance of the hybrid system under different scenarios using real meteorological data.It is shown that the performances of the hybrid system connected to the electrical network depend obviously on the available energy resources and constraints because the renewable energies are intermittent.In addition,the price of the kWh of electricity supplied by the hybrid system is determined,which amounts to$0.209/kWh,which is very cost effective and satisfactory for the considered sample conditions(Comoros Island).
文摘This research paper proposes a single phase fifteen level inverter for a grid connected PV system.The proposed inverter is also called cascaded asymmetric multilevel inverter.By adopting appropriate hybrid modulation technique improved output voltage is obtained with minimum number of power electronic switches.By reducing the number of gate triggering circuits of the switches,the size and power consumption of the driving circuits can be reduced.The total harmonic distortion of the output of the inverter is improved by this inverter.The proposed inverter developed by cascading a full bridge inverter with modified H bridge multilevel inverter.The validity of the proposed system is verified through MATLAB simulations.
基金The project supported by National Natural Science Foundation of China under Grant No. 90403019 Acknowledgments We would like to thank Prof. Kang-Jie Shi for many stimulating discussions. Xie is also grateful to Zhan-Yun Wang, Xiao-Lin Cai, Pei Song, and Jun Feng for their helpful discussions, and especially A-Ping Yang＇s encouragements.
文摘In this paper, we show that there exists a twisted duality symmetry between the Maurer-Cartan equations and the equations of motion in the hybrid formalism for the type liB superstring in an AdS2 ×S2 background with Ramond-Ramond flux. As a result, from the twisted duality transformation, we construct the Lax connection with the spectral parameter, which ensures the integrability of the system.
文摘结合钢筋混凝土结构和钢结构的优势,设计一种型钢-螺栓-后浇混凝土装配式剪力墙型钢混合连接。基于ABAQUS有限元软件建立混合连接的剪力墙模型,探究低周往复荷载作用下该混合连接预制剪力墙的受力性能,主要分析模型的破坏形态、受力机制、变形曲线、特征承载力等,并扩展分析了材料强度、轴压比、连接件数量、型钢截面高度等参数对模型受力性能影响。结果表明:装配式剪力墙破坏形态为压弯破坏,破坏时钢连接件仍保持完整,符合“强连接,弱墙肢”的基本设计理念;装配式剪力墙具有较好的承载力、延性和刚度;轴压比对结构承载力影响显著,型钢混合连接间距的增大能有效提升剪力墙延性。建立了型钢混合连接抗剪需求承载力计算模型和公式,并与国内外规范计算值对比分析,公式计算值和BS EN 1992欧洲规范计算值分别与模拟值的误差在15%和20%以内,均可用于型钢混合连接剪力墙竖缝受剪承载力设计参考。
