Hybrid Predictive Control with Simple Linear Control Based Circulating Current Suppression for Modular Multilevel Converters

The modular multilevel converter(MMC)has become a promising topology for widespread power converter applications.However,an evident circulating current flowing between the phases will increase system losses and complicate the heatsink design.This paper proposes a novel hybrid model predictive control method for MMCs.This method utilizes an indirect structure MPC and a sorting algorithm to implement current tracking and capacitor voltages balancing,considerably resulting in reduced calculation burden.In addition,different from the conventional MPC solutions,we add a simple proportional-integral(PI)controller to suppress circulating current through modifying the submodule(SM)inserted number,which is parallel to the MPC loop.This hybrid control solution combines both advantages of MPC and linear control,evidently resulting in improved performance of circulating current.Finally,the MATLAB/Simulink results of an 11-level MMC system verify the effectiveness of the proposed solution.

Regulation Method for Torque-Angle Characteristics of Rotary Electric-Mechanical Converter Based on Hybrid Air Gap

The torque-angle characteristics of electric-mechanical converters are important determinants of the quality of electrohydraulic proportional control systems.It is far more difficult for a rotary electric-mechanical converter(REMC)to obtain flat torque-angle characteristics than traditional proportional solenoid,greatly influencing the promotion and application of rotary valves for electrohydraulic proportional control systems.A simple and feasible regulation method for the torque-angle characteristics of REMCs based on a hybrid air gap is proposed.The regulation is performed by paralleling an additional axial air gap with the original radial air gap to obtain a flat torque-angle characteristic and increase output torque.For comparison,prototypes of REMCs based on hybrid and radial air gaps were manufactured,and a special test rig was built.The torque-angle characteristics under different excitation currents and step responses were studied by magnetic circuit analysis,finite element simulation,and experimental research.The experimental results were consistent with the theoretical analysis.It was shown that REMCs based on a hybrid air gap can obtain a flat torque-angle characteristic with further optimizing of key structural parameters and also increase output torque.This regulation method provides a new approach for the design of proportional rotary electromechanical converters.

A Novel Serial Hybrid Three-level NPC Topology for Multi-MW Medium Voltage Wind Power Converters

提出一种新型的串联混合三电平中点钳位（neutralpoint clamped,NPC）拓扑,该拓扑是基于传统三电平NPC拓扑的改进和优化,引入大功率IGBT的串联应用。该新型拓扑中,桥臂的两个外管分别用两个低压IGBT串联,两个内管均用高压IGBT。在多兆瓦级中压风电变流器中,大功率IGBT的开关损耗很大,从而限制了开关频率。提出的新型拓扑通过低压IGBT的串联来减小功率器件的损耗,从而提高开关频率,同时可减小输出滤波器的尺寸。通过传统三电平拓扑和新型串联混合三电平拓扑IGBT损耗的对比,说明新拓扑的优势。通过改变门极驱动电阻实现串联IGBT的均压,对新拓扑的应用具有重大意义。最后通过新拓扑的单相样机验证新拓扑的正确性和可行性。

Improved Dynamic Response of DC to DC Converter Using Hybrid PSO Tuned Fuzzy Sliding Mode Controller

DC/DC switching converters are widely used in numerous appliances in modern existence. In this paper, the dynamic and transient response of phase shift series resonant DC/DC converter are improved using hybrid particle swarm optimization tuned fuzzy sliding mode controller under starting and load step change conditions. The aim of the control is to regulate the output voltage beneath the load change. The model of the hybrid particle swarm optimization tuned fuzzy sliding mode controller is implemented using Sim Power Systems toolbox of MATLAB SIMULINK. Performance of the proposed dynamic novel control under step load change condition is investigated.

H-bridge Hybrid Converter Modeling and Synthesize with Power Sharing Analysis

In this paper hybrid converters with double inputs are investigated. Mainly any possible topologies are constructed and only one of them is chosen and modeled in none ideal format, by state space averaging method. After that small signal model and equilibrium point of that model is calculated. Finally with power sharing analysis the best point in efficiency was calculated.

A Novel Polymorphic Topology with Hybrid Control Strategy Based LLC Resonant Converter for Ultra-Wide Input Voltage Range Applications

To realize effective utilization of renewable energy sources,a novel polymorphic topology with hybrid control strategy based LLC resonant converter was analyzed and designed in this paper.By combining the merits of a full bridge LLC resonant converter,three-level half bridge LLC resonant converter,and variable frequency control mode,the converter realizes an intelligent estimation of input voltage by automatically changing its internal cir-cuit topology.Under this control strategy,different input voltages determine different operation modes.This is achieved in full bridge LLC mode when the input voltage is low.If the input voltage rises to a certain level,it operates in three-level half bridge LLC mode.These switches are digital and entirely carried out by the DSP(Digi-tal Signal Processor),which means that an auxiliary circuit is unnecessary,where a simple strategy of software modification can be utilized.Experimental results of a 500W prototype with 100V~600V input voltage and full load efficiency of up to 92%are developed to verify feasibility and practicability.This type of converter is suitable for applications with an ultra-wide input voltage range,such as wind turbines,photovoltaic generators,bioenergy,and other renewable energy sources.

Performance Evaluation of a Molten Carbonate Fuel Cell-Graphene Thermionic Converter-Thermally Regenerative Electrochemical Cycles Hybrid System

A combined system model is proposed including a molten carbonate fuel cell(MCFC),a graphene thermionic converter(GTIC)and thermally regenerative electrochemical cycles(TRECs).The expressions for power output,energy efficiency of the subsystems and the couple system are formulated by considering several irreversible losses.Energy conservation equations between the subsystems are achieved leaned on the first law of thermodynamics.The optimum operating ranges for the combined system are determined compared with the MCFC system.Results reveal that the peak power output density(POD)and the corresponding energy efficiency are 28.22%and 10.76%higher than that of the single MCFC system,respectively.The effects of five designing parameters on the power density and energy efficiency of the MCFC/GTIC/TRECs model are also investigated and discussed.

Hybrid Control Strategy for Matrix Converter Fed Wind Energy Conversion System

In this paper, a hybrid control strategy for a matrix converter fed wind energy conversion system is presented. Since the wind speed may vary, output parameters like power, frequency and voltage may fluctuate. Hence it is necessary to design a system that regulates output parameters, such as voltage and frequency, and thereby provides a constant voltage and frequency output from the wind energy conversion system. Matrix converter is used in the proposed solution as the main power conditioner as a more efficient alternative when compared to traditional back-back converter structure. To control the output voltage, a vector modulation based refined control structure is used. A power tracker is included to maximize the mechanical output power of the turbine. Over current protection and clamp circuit input protection have been introduced to protect the system from over current. It reduces the spikes generated at the output of the converter. The designed system is capable of supplying an output voltage of constant frequency and amplitude within the expected ranges of input during the operation. The matrix converter control using direct modulation method, modified Venturini modulation method and vector modulation method was simulated, the results were compared and it was inferred that vector modulation method was superior to the other two methods. With the proposed technique, voltage transfer ratio and harmonic profile have been improved compared to the other two modulation techniques. The behaviour of the system is corroborated by MATLAB Simulink, and hardware is realized using an FPGA controller. Experimental results are found to be matching with the simulation results.

Analysis of Non-Sinusoidal Steady Electric Field of ±500 kV Converter Transformer

The line side winding is under the fundamental frequency AC voltage, while the valve side winding contains not only fundamental AC voltage component, but also the DC voltage component, fundamental AC voltage component, and higher harmonic voltage components when the converter transformer is at its normal operating condition, and the electric field of converter transformer is a non-sinusoidal steady one. To analyze the non-sinusoidal steady electric field containing the DC component, fundamental AC and higher harmonic components, the voltage spectrum of the valve winding in a ±500 kV converter transformer is firstly analyzed, and the non-sinusoidal periodic steady electric field is obtained by the fast discrete Fourier transform. Different resistivity of the oil and oil-immersed paper is adopted to simulate the aging of oil paper insulation at operation, and get the non-sinusoidal steady electric field.

All optical wavelength converter and its application in optical network

All optical network （AON） is a hot topic in recent studies of optical fiber communications. Key techniques in AON include optical switching/routing, optical cross connection （OXC）, all optical wavelength conversion （AOWC）, all optical buffering, etc. Opti- cal switching/routing is in fact wavelength switching/ routing. OXC and wavelength conversion （WC） are introduced into cross nodes so that a virtual wavelength path is established. With WC, communication route is formed only if there is unused wavelength in an individual segment link. The rate wavelength usage is thus greatly increased. The blocking rate of network can be reduced by adding WCs, especially for huge capacity multiple nodes ones. Therefore, WC has attracted much attention in basic research of optical communication and is used in some experimental networks.This dissertation studies all optic wavelength conversion and its application, with the contributions in the following five aspects.

Exploitation of Waste Heat from a Solid Oxide Fuel Cell via an Alkali Metal Thermoelectric Converter and Electrochemical Cycles

In order to employ the waste heat effectively,a novel three-stage integrated system based upon a solid oxide fuel cell(SOFC),an alkali metal thermoelectric converter(AMTEC)and thermally regenerative electrochemical cycles(TRECs)is put forward.Considering the main electrochemically and thermodynamically irreversible losses,the power output and the efficiency of the subsystems and the integrated system are compared,and optimally operating regions for the current density,the power output,and the efficiency of the integrated system are explored.Calculations demonstrate that the maximum power density of the considered system is up to 7466 W/m2,which allows 18%and 74%higher than that of the conventional SOFC-AMTEC device and the stand-alone fuel cell model,respectively.It is proved that the considered system is an efficient approach to boost energy efficiency.Moreover,the influence of several significant parameters on the comprehensive performance of the integrated system is expounded in detail,including the electrolyte thickness of the SOFC,the leakage resistance of the SOFC,and the area ratio between the SOFC electrode and the AMTEC subsystem.

EMCO-based Optimal Layout Design of Hybrid Wind-wave Energy Converters Array

Marine renewable energy,combining wave energy converters(WECs)and floating wind turbines(FWTs)into hybrid wave-wind energy converters(HWWECs),garners significant global interest.HWWECs offer potential cost reductions,increased power generation,and enhanced system stability.The absorption power of high wind energy sites is primarily influenced by the complex hydrodynamic interactions among floating bodies,which are closely related to the location and wind-wave environment of high wind energy sites.To delve into the positive interactions among HWWECs,this paper proposes a HWWEC array optimization strategy based on the artificial ecosystem opti-mization-manta ray foraging optimization coordinated optimizer(EMCO).In EMCO,the decomposition operator of artificial ecosystem optimization(AEO)and the flipping-dipper foraging operator of manta ray foraging optimization coordinated(MRFO)cooperate dynamically to effectively balance local exploitation and global exploration.To validate the effectiveness of EMCO,experiments were conducted in scenarios with 3,5,8,and 20 HWWECs,and compared with five typical algorithms.Experimental results demonstrate the existence of multiple optimal solutions for HWWEC arrays.EMCO achieves maximum total absorp-tion power and exhibits good stability.Notably,EMCO en-hances the q-factor values of HWWECs across four scales:1.0478,1.0586,1.0612,and 0.9965,respectively.

Transient Characteristics and Accommodative Current Limiting Strategy for Bidirectional Interlinking Converters in Hybrid AC/DC Microgrids

Bidirectional interlinking converter(BIC)is the core equipment in a hybrid AC/DC microgrid connected between AC and DC sub-grids.However,the variety of control modes and flexible bidirectional power flow complicate the influence of AC faults on BIC itself and on DC sub-grid,which potentially threaten both converter safety and system reliability.This study first investigates AC fault influence on the BIC and DC bus voltage under different BIC control modes and different pre-fault operation states,by developing a mathematical model and equivalent sequence network.Second,based on the analysis results,a general accommodative current limiting strategy is proposed for BIC without limitations to specific mode or operation condition.Current amplitude is predicted and constrained according to the critical requirements to protect the BIC and relieving the AC fault influence on the DC bus voltage.Compared with conventional methods,potential current limit failure and distortions under asymmetric faults can also be avoided.Finally,experiments verify feasibility of the proposed method.

A comprehensive review on hybrid electric vehicles: architectures and components

The rapid consumption of fossil fuel and increased environmental damage caused by it have given a strong impetus to the growth and development of fuelefficient vehicles. Hybrid electric vehicles (HEVs) have evolved from their inchoate state and are proving to be a promising solution to the serious existential problem posed to the planet earth. Not only do HEVs provide better fuel economy and lower emissions satisfying environmental legislations, but also they dampen the effect of rising fuel prices on consumers. HEVs combine the drive powers of an internal combustion engine and an electrical machine. The main components of HEVs are energy storage system, motor, bidirectional converter and maximum power point trackers (MPPT, in case of solar-powered HEVs). The performance of HEVs greatly depends on these components and its architecture. This paper presents an extensive review on essential components used in HEVs such as their architectures with advantages and disadvantages, choice of bidirectional converter to obtain high efficiency, combining ultracapacitor with battery to extend the battery life, traction motors’ role and their suitability for a particular application. Inclusion of photovoltaic cell in HEVs is a fairly new concept and has been discussed in detail. Various MPPT techniques used for solar-driven HEVs are also discussed in this paper with their suitability.

Hybrid MPPT approach using Cuckoo Search and Grey Wolf Optimizer for PV systems under variant operating conditions

Photovoltaic(PV)systems are adversely affected by partial shading and non-uniform conditions.Meanwhile,the addition of a bypass shunt diode to each PV module prevents hotspots.It also produces numerous peaks in the PV array’s power-voltage characteristics,thereby trapping conventional maximum power point tracking(MPPT)methods in local peaks.Swarm optimization approaches can be used to address this issue.However,these strategies have an unreasonably long convergence time.The Grey Wolf Optimizer(GWO)is a fast and more dependable optimization algorithm.This renders it a good option for MPPT of PV systems operating in varying partial shading.The conventional GWO method involves a long conversion time,large steady-state oscillations,and a high failure rate.This work attempts to address these issues by combining Cuckoo Search(CS)with the GWO algorithm to improve the MPPT performance.The results of this approach are compared with those of conventional MPPT according to GWO and MPPT methods based on perturb and observe(P&O).A comparative analysis reveals that under non-uniform operating conditions,the hybrid GWO CS(GWOCS)approach presented in this article outperforms the GWO and P&O approaches.

Studies of commutation failures in hybrid LCC/MMC HVDC systems

A hybrid of line commutated converters(LCCs)and modular multi-level converters(MMCs)can provide the advantages of both the technologies.However,the commutation failure still exists if the LCC operates as an inverter in a hybrid LCC/MMC system.In this paper,the system behavior during a commutation failure is investigated.Both halfbridge and full-bridge MMCs are considered.Control strategies are examined through simulations conducted in PSCAD/EMTDC.Additionally,commutation failure protection strategies for multi-terminal hybrid LCC/MMC systems with AC and DC circuit breakers are studied.This paper can contribute to the protection design of future hybrid LCC/MMC systems against commutation failures.

MMC-MTDC Transmission System with Partially Hybrid Branches

This paper proposes a hybrid submodule modular multilevel converter(MMC)topology which is suitable for multi terminal direct current(MTDC)transmission systems.Each arm of the proposed MMC topology consists of a half-bridge submodule(HBSM)branch and two parallel full-bridge submodule(FBSM)branches.Comparing with the conventional MTDC transmission system,the proposed topology can selectively block the DC fault current and isolate the corresponding fault line without expensive DC circuit breakers(DCCBs).Thus,the influence range of the DC fault can be reduced and the reliability of the power supply can be improved as well.The corresponding modulation and voltage balancing strategies are developed for the proposed hybrid MMC topology.The feasibility of the proposed topology and control strategy is verified in the MATLAB/Simulink simulation.

Damping controller design based on FO-PID-EMA in VSC HVDC system to improve stability of hybrid power system

Wind energy sources have different structures and functions from conventional power plants in the power system.These resources can affect the exchange of active and reactive power of the network.Therefore,power system stability will be affected by the performance of wind power plants,especially in the event of a fault.In this paper,the improvement of the dynamic stability in power system equipped by wind farm is examined through the supplementary controller design in the high voltage direct current(HVDC)based on voltage source converter(VSC)transmission system.In this regard,impacts of the VSC HVDC system and wind farm on the improvement of system stability are considered.Also,an algorithm based on controllability(observability)concept is proposed to select most appropriate and effective coupling between inputs-outputs(IO)signals of system in different work conditions.The selected coupling is used to apply damping controller signal.Finally,a fractional order PID controller(FO-PID)based on exchange market algorithm(EMA)is designed as damping controller.The analysis of the results shows that the wind farm does not directly contribute to the improvement of the dynamic stability of power system.However,it can increase the controllability of the oscillatory mode and improve the performance of the supplementary controller.

Maximum Power Extraction Control Algorithm for Hybrid Renewable Energy System

In this research,a modified fractional order proportional integral derivate(FOPID)control method is proposed for the photovoltaic(PV)and thermoelectric generator(TEG)combined hybrid renewable energy system.The faster tracking and steady-state output are aimed at the suggested maximum power point tracking(MPPT)control technique.The derivative order number(μ)value in the improved FOPID(also known as PIλDμ)control structure will be dynamically updated utilizing the value of change in PV array voltage output.During the transient,the value ofμis changeable;it’s one at the start and after reaching the maximum power point(MPP),allowing for strong tracking characteristics.TEG will use the freely available waste thermal energy created surrounding the PVarray for additional power generation,increasing the system’s energy conversion efficiency.A high-gain DC-DC converter circuit is included in the system to maintain a high amplitude DC input voltage to the inverter circuit.The proposed approach’s performance was investigated using an extensive MATLAB software simulation and validated by comparing findings with the perturbation and observation(P&O)type MPPT control method.The study results demonstrate that the FOPID controller-based MPPT control outperforms the P&O method in harvesting the maximum power achievable from the PV-TEG hybrid source.There is also a better control action and a faster response.