A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is est...A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is established by expanding the essential terms of the assumed stress field as polynomials in the natural coordinates of the element. The homogeneous equilibrium equations are imposed in a variational sense through the internal displacements which are also expanded in the natural coordinates, while the tractionfree conditions along the inclined side are satisfied exactly. The use of such special element in the finite element solution is shown to be highly accurate when only a very coarse element mesh is used for plates with V-shaped rounded notches or inclined sides.展开更多
The three-dimensional stress concentration factor (SCF) at the edge of elliptical and circular holes in infinite plates under remote tension has been extensively investigated considering the variations of plate thickn...The three-dimensional stress concentration factor (SCF) at the edge of elliptical and circular holes in infinite plates under remote tension has been extensively investigated considering the variations of plate thickness, hole dimensions and material properties, such as the Poisson’s coefficient. This study employs three dimensional finite element modeling to numerically investigate the effect of plate width on the behavior of the SCF across the thickness of linear elastic isotropic plates with a through-the-thickness circular hole under remote tension. The problem is governed by two geometric non-dimensional parameters, i.e., the plate half-width to hole radius (W/r) and the plate thickness to hole radius (B/r) ratios. It is shown that for thin plates the value of the SCF is nearly constant throughout the thickness for any plate width. As the plate thickness increases, the point of maximum SCF shifts from the plate middle plane and approaches the free surface. When the ratio of plate half-width to hole radius (W/r) is greater than four, the maximum SCF was observed to approximate the theoretical value determined for infinite plates. When the plate width is reduced, the maximum SCF values significantly increase. A polynomial curve fitting was employed on the numerical results to generate empirical formulas for the maximum and surface SCFs as a function of W/r and B/r. These equations can be applied, with reasonable accuracy, to practical problems of structural strength and fatigue, for instance.展开更多
文摘A new kind of quadrilateral assumed stress hy- brid membrane element with drilling degrees of freedom and a traction-free inclined side has been developed based on an extended Hellinger-Reissner principle which is established by expanding the essential terms of the assumed stress field as polynomials in the natural coordinates of the element. The homogeneous equilibrium equations are imposed in a variational sense through the internal displacements which are also expanded in the natural coordinates, while the tractionfree conditions along the inclined side are satisfied exactly. The use of such special element in the finite element solution is shown to be highly accurate when only a very coarse element mesh is used for plates with V-shaped rounded notches or inclined sides.
基金the support of the National Council for Scientific and Technological Development(CNPq)for this work.
文摘The three-dimensional stress concentration factor (SCF) at the edge of elliptical and circular holes in infinite plates under remote tension has been extensively investigated considering the variations of plate thickness, hole dimensions and material properties, such as the Poisson’s coefficient. This study employs three dimensional finite element modeling to numerically investigate the effect of plate width on the behavior of the SCF across the thickness of linear elastic isotropic plates with a through-the-thickness circular hole under remote tension. The problem is governed by two geometric non-dimensional parameters, i.e., the plate half-width to hole radius (W/r) and the plate thickness to hole radius (B/r) ratios. It is shown that for thin plates the value of the SCF is nearly constant throughout the thickness for any plate width. As the plate thickness increases, the point of maximum SCF shifts from the plate middle plane and approaches the free surface. When the ratio of plate half-width to hole radius (W/r) is greater than four, the maximum SCF was observed to approximate the theoretical value determined for infinite plates. When the plate width is reduced, the maximum SCF values significantly increase. A polynomial curve fitting was employed on the numerical results to generate empirical formulas for the maximum and surface SCFs as a function of W/r and B/r. These equations can be applied, with reasonable accuracy, to practical problems of structural strength and fatigue, for instance.
