Shear behaviour of a rock bridge sandwiched between incipient joints under the influence of hydraulic pressures

The rock bridges sandwiched in incipiently jointed rock mass were considered as barriers that block the fluid seepage,and provide certain shear strength reservation.For better revealing the influence of hydraulic pressure on the failure behaviour of rock bridges,direct shear tests were carried out through a newly proposed method on rock samples that contain two parallel incipient joints.By developing the gypsum-silicone pad coupling samples,a conventional triaxial test system was qualified to implement direct shear tests with satisfied sealing capability.The results showed that the rock bridges could be failed through the tensile failure,shear failure and mixed failure mechanism.The hydraulic pressure would facilitate the tensile failure mechanism and induce rougher fracture surfaces;while the normal stress would facilitate the shear failure mechanism and induce less rough fracture.The hydraulic pressure reduced the global shear strength of the rock block through reducing the efficient normal stress applied on the rock bridge area,which was highly dependent on the joint persistence,k.Moreover,because of the iterating occurrence of the hydraulic pressure lag with the fracture propagation,the rock bridge failure stage in the shear stress-shear displacement curves displayed a fluctuation trend.

Influence of specific speed on hydraulic performances and pressure fluctuations in mixed-flow pumps

A series of steady and unsteady numerical calculations of the internal flow in mixed-flow pumps with three different specific speeds were carried out based on the N-S equation coupled with the standard k-εturbulence model under different operating conditions to investigate the relationship between the impeller specific speed and the pump performance as well as pressure pulsations.Meanwhile,the pump performance and pressure pulsations inside the mixed-flow pump with three different specific speeds were also analyzed and compared with the corresponding test data.From the results,the averaged deviations between the predicted and tested head among different impellers are below 5%,and with respect to the equivalent impeller specific speeds of 280 and 260,the values are 4.30%and 3.69%,respectively.For all the impeller schemes,the best efficiency point of the mixed-flow pump is found at the flow rate of 1.2 Q_(d) and the higher head deviation occurs at lower flow rates.Especially,it can be found that the specific speed has a slight effect on the pressure fluctuation in the impellers.Eventually,it is determined that the pump performance curves calculated by numerical simu-lations have good agreement with the relevant experimental results,which verifies that the numerical methods used in the present study are accurate to a certain extent.Furthermore,the results also provide some references to the pressure pulsation analysis and the performance improvement of the mixed-flow pump design.

Fracture geometry and breakdown pressure of radial borehole fracturing in multiple layers

Radial borehole fracturing that combines radial boreholes with hydraulic fracturing is anticipated to improve the output of tight oil and gas reservoirs.This paper aims to investigate fracture propagation and pressure characteristics of radial borehole fracturing in multiple layers.A series of laboratory experiments with artificial rock samples(395 mm×395 mm×395 mm)was conducted using a true triaxial fracturing device.Three crucial factors corresponding to the vertical distance of adjacent radial borehole layers(vertical distance),the azimuth and diameter of the radial borehole are examined.Experimental results show that radial borehole fracturing in multiple layers generates diverse fracture geometries.Four types of fractures are identified based on the connectivity between hydraulic fractures and radial boreholes.The vertical distance significantly influences fracture propagation perpendicular to the radial borehole axis.An increase in the vertical distance impedes fracture connection across multiple radial borehole layers and reduces the fracture propagation distance along the radial borehole axis.The azimuth also influences fracture propagation along the radial borehole axis.Increasing the azimuth reduces the guiding ability of radial boreholes,which makes the fracture quickly curve to the maximum horizontal stress direction.The breakdown pressure correlates with diverse fracture geometries observed.When the fractures connect multi-layer radial boreholes,increasing the vertical distance decreases the breakdown pressure.Decreasing the azimuth and increasing the diameter also decrease the breakdown pressure.The extrusion force exists between the adjacent fractures generated in radial boreholes in multiple rows,which plays a crucial role in enhancing the guiding ability of radial boreholes and results in higher breakdown pressure.The research provides valuable theoretical insights for the field application of radial borehole fracturing technology in tight oil and gas reservoirs.

Numerical Analysis of Perforation during Hydraulic Fracture Initiation Based on Continuous-Discontinuous Element Method

Perforation is a pivotal technique employed to establish main flow channels within the reservoir formation at the outset of hydraulic fracturing operations.Optimizing perforation designs is critical for augmenting the efficacy of hydraulic fracturing and boosting oil or gas production.In this study,we employ a hybrid finite-discrete element method,known as the continuous–discontinuous element method(CDEM),to simulate the initiation of post-perforation hydraulic fractures and to derive enhanced design parameters.The model incorporates the four most prevalent perforation geometries,as delineated in an engineering technical report.Real-world perforations deviate from the ideal cylindrical shape,exhibiting variable cross-sectional profiles that typically manifest as an initial constriction followed by an expansion,a feature consistent across all four perforation types.Our simulations take into account variations in perforation hole geometries,cross-sectional diameters,and perforation lengths.The findings show that perforations generated by the 39g DP3 HMX perforating bullet yield the lowest breakdown pressure,which inversely correlates with increases in sectional diameter and perforation length.Moreover,this study reveals the relationship between breakdown pressure and fracture degree,providing valuable insights for engineers and designers to refine perforation strategies.

Wellbore Cleaning Degree and Hydraulic Extension in Shale Oil Horizontal Wells

The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.

Simulation Method and Feature Analysis of Shutdown Pressure Evolution During Multi-Cluster Fracturing Stimulation

Multistage multi-cluster hydraulic fracturing has enabled the economic exploitation of shale reservoirs,but the interpretation of hydraulic fracture parameters is challenging.The pressure signals after pump shutdown are influenced by hydraulic fractures,which can reflect the geometric features of hydraulic fracture.The shutdown pressure can be used to interpret the hydraulic fracture parameters in a real-time and cost-effective manner.In this paper,a mathematical model for shutdown pressure evolution is developed considering the effects of wellbore friction,perforation friction and fluid loss in fractures.An efficient numerical simulation method is established by using the method of characteristics.Based on this method,the impacts of fracture half-length,fracture height,opened cluster and perforation number,and filtration coefficient on the evolution of shutdown pressure are analyzed.The results indicate that a larger fracture half-length may hasten the decay of shutdown pressure,while a larger fracture height can slow down the decay of shutdown pressure.A smaller number of opened clusters and perforations can significantly increase the perforation friction and decrease the overall level of shutdown pressure.A larger filtration coefficient may accelerate the fluid filtration in the fracture and hasten the drop of the shutdown pressure.The simulation method of shutdown pressure,as well as the analysis results,has important implications for the interpretation of hydraulic fracture parameters.

Reliability Design for Impact Vibration of Hydraulic Pressure Pipeline Systems

The research of reliability design for impact vibration of hydraulic pressure pipeline systems is still in the primary stage,and the research of quantitative reliability of hydraulic components and system is still incomplete.On the condition of having obtained the numerical characteristics of basic random parameters,several techniques and methods including the probability statistical theory,hydraulic technique and stochastic perturbation method are employed to carry out the reliability design for impact vibration of the hydraulic pressure system.Considering the instantaneous pressure pulse of hydraulic impact in pipeline,the reliability analysis model of hydraulic pipeline system is established,and the reliability-based optimization design method is presented.The proposed method can reflect the inherent reliability of hydraulic pipe system exactly,and the desired result is obtained.The reliability design of hydraulic pipeline system is achieved by computer programs and the reliability design information of hydraulic pipeline system is obtained.This research proposes a reliability design method,which can solve the problem of the reliability-based optimization design for the hydraulic pressure system with impact vibration practically and effectively,and enhance the quantitative research on the reliability design of hydraulic pipeline system.The proposed method has generality for the reliability optimization design of hydraulic pipeline system.

Effects of Loading Paths on Hydrodynamic Deep Drawing with Independent Radial Hydraulic Pressure of Aluminum Alloy Based on Numerical Simulation

In order to meet the forming demands for low plasticity materials and large height-diameter ratio parts, a new process of hydrodynamic deep drawing （HDD） with independent radial hydraulic pressure is proposed. To investigate the effects of loading paths on the HDD with independent radial hydraulic pressure, the forming process of 5A06 aluminum alloy cylindrical cup with a hemispherical bottom was studied by numerical simulation. By employing the dynamic explicit analytical software ETA/Dynaform based on LS-DYNA3D, the effects of loading paths on the sheet-thickness distribution and surface quality were analyzed. The corresponding relations of the radial hydraulic pressure loading paths and the part＇s strain status on the forming limit diagram （FLD） were also discussed. The results indicated that a sound match between liquid chamber pressure and independent radial hydraulic pressure could restrain the serious thinning at the hemisphere bottom and that through adjusting radial hydraulic pressure could reduce the radial tensile strain and change the strain paths. Therefore, the drawing limit of the aluminum cylindrical cup with a hemispherical bottom could be increased significantly.

Fractured rock mass hydraulic fracturing under hydrodynamic and hydrostatic pressure joint action

According to the stress state of the crack surface, crack rock mass can be divided into complex composite tensile-shear fracture and composite compression-shear fracture from the perspective of fracture mechanics. By studying the hydraulic fracturing effect of groundwater on rock fracture, the tangential friction force equation of hydrodynamic pressure to rock fracture is deduced. The hydraulic fracturing of hydrostatic and hydrodynamic pressure to rock fracture is investigated to derive the equation of critical pressure when the hydraulic fracturing effect occurs in the rock fracture. Then, the crack angle that is most prone to hydraulic fracturing is determined. The relationships between crack direction and both lateral pressure coefficient and friction angle of the fracture surface are analyzed. Results show that considering the joint effect of hydrodynamic and hydrostatic pressure, the critical pressure does not vary with the direction of the crack when the surrounding rock stationary lateral pressure coefficient is equal to 1.0. Under composite tensile-shear fracture, the crack parallel to the direction of the main stress is the most prone to hydraulic fracturing. Under compression-shear fracture, the hydrodynamic pressure resulting in the most dangerous crack angle varies at different lateral pressure coefficients; this pressure decreases when the friction angle of the fracture surface increases. By referring to the subway tunnel collapse case, the impact of fractured rock mass hydraulic fracturing generated by hydrostatic and hydrodynamic pressure joint action is calculated and analyzed.

Effect of persistent high intraocular pressure on microstructure and hydraulic permeability of trabecular meshwork

As the aqueous humor leaves the eye, it first passes through the trabecular meshwork （TM）. Increased flow resistance in this region causes elevation of intraocular pressure （IOP）, which leads to the occurrence of glaucoma. To quantitatively evaluate the effect of high IOP on the configuration and hydraulic permeability of the TM, second harmonic generation （SHG） microscopy was used to image the microstructures of the TM and adjacent tissues in control （normal） and high IOP conditions. Enucleated rabbit eyes were perfused at a pressure of 60 mmHg to achieve the high lOP. Through the anterior chamber of the eye, in situ images were obtained from different depths beneath the surface of the TM. Porosity and specific surface area of the TM in control and high IOP conditions were then calculated to estimate the effect of the high pressure on the permeability of tissue in different depths. We further photographed the histological sections of the TM and compared the in situ images. The following results were obtained in the control condition, where the region of depth was less than 55 μm with crossed branching beams and large pores in the superficial TM. The deeper meshwork is a silk-like tissue with abundant fluorescence separating the small size of pores. The total thickness of pathway tissues composed of TM and juxtacanalicular （JCT） is more than 100 p.m. After putting a high pressure on the inner wall of the eye, the TM region progressively collapses and decreases to be less than 40 μm. Fibers of the TM became dense, and the porosity at 34 μm in the high IOP condition is comparable to that at 105 μm in the control condition. As a consequent result, the permeability of the superficial TM decreases rapidly from 120 μm2 to 49.6 μm2 and that of deeper TM decreases from 1.66 μm2 to 0.57 μm2. Heterogeneity reflected by descent in permeability reduces from 12.4 μm of the control condition to 3.74 μm of the high IOP condition. The persistently high IOP makes the TM region collapse from its normal state, in which the collagen fibers of the TM are arranged in regular to maintain the physiological permeability of the outflow pathway. In the scope of pathologically high IOP, the microstructure of the TM is sensitive to pressure and hydraulic permeability can be significantly affected by IOP.

Effects of shifting time on pressure impact in hydraulic systems

The limitations in existing measures for absorbing pressure impact in hydraulic systems were summarized in this paper. Based on the forming principle of the oil in a hydrostatic closed pressure chamber, the underlying reasons of the pressure impact were analyzed theoretically, the intrinsic laws that the extent of the pressure impact in hydraulic oil lines are affected by some factors, such as oil elastic modulus, oil line's geometrical volume, and changing rate of oil volume versus time etc, were discussed. Experimental investigations into pressure impact in all pressure chambers because of shifting were conducted under different working conditions by employing a special experimental system. The effects of shifting time on pressure impact were studied. A new concept with universal meaning, i.e. optimal shifting time, and its characterizing parameter and the methods of shifting at optimal shifting time were also proposed. The results show that shifting time lag △t is of rationality and maneuverablility. The higher the working pressure, the shorter the shifting time.

Research Status, Critical Technologies, and Development Trends of Hydraulic Pressure Pulsation Attenuator

Hydraulic pumps are a positive displacement pump whose working principle causes inherent output flow pulsation.Flow pulsation produces pressure pulsation when encountering liquid resistance.Pressure pulsation spreads in the pipeline and causes vibration,noise,damage,and even pipeline rupture and major safety accidents.With the development of airborne hydraulic systems with high pressure,power,and flow rate,the hazards of vibration and noise caused by pressure pulsation are also amplified,severely restricting the application and development of hydraulic systems.In this review paper,the mechanism,harm,and suppression method of pressure pulsation in hydraulic systems are analyzed.Then,the classification and characteristics of pulsation attenuators according to different working principles are described.Furthermore,the critical technology of simulation design,matching method with airborne piston pumps,and preliminary design method of pulsation attenuators are proposed.Finally,the development trend of pulsation attenuators is prospected.This paper provides a reference for the research and application of pressure pulsation attenuators.

ESTIMATION OF RESIDUAL CONTACT PRESSURE IN HYDRAULICALLY EXPANDED CRA-LINED PIPE

The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lined pipe. A simplified theoretical method ispresented to predict the residual contact pressure created by hydraulic pressure. The calculatingequation related hydro-forming pressure to the residual contact pressure between two metal faces isderived. And the validation of the proposed equation is accomplished by comparing its result tothose obtained by experimental investigation.

Effect of internal pressure on strength of hydraulically expanded joints

To analyze the effect of internal pressure on the connection strength of hydraulically expanded joints,a hydraulic expanding and push-out process of a joint of tube to sleeve was simulated by using FEM and validated by experiments at various internal pressure values.The stress and residual stress in the joined pair during the joining process illustrates that the contact pressure on the interface is not uniform along the longitudinal direction.The research reveals that if the sleeve does not experience any plastic deformation,the connection strength increases with the internal pressure linearly.For sleeve material with yield point elongation,if the sleeve experiences some degree of plastic deformation,there is an internal pressure interval in which the connection strength decreases slightly as internal pressure increases.Therefore,the internal pressure should be controlled depending on the deformation of the sleeve,but not as high as possible.The simulated results are in good agreement with those from experiments.

Sliding Mode Control of Hydraulic Pressure in Electro-Hydraulic Brake System Based on the Linearization of Higher-Order Model

The possibility to enhance the stability and robustness of electrohydraulic brake(EHB)systems is considered a subject of great importance in the automotive field.In such a context,the present study focuses on an actuator with a four-way sliding valve and a hydraulic cylinder.A 4-order nonlinear mathematical model is introduced accordingly.Through the linearization of the feedback law of the high order EHB model,a sliding mode control method is proposed for the hydraulic pressure.The hydraulic pressure tracking controls are simulated and analyzed by MATLAB/Simulink soft considering separately different conditions,i.e.,a sine wave,a square wave and a square wave with superimposed sine disturbance.The results show that the proposed strategy can track the target within 0.25 s,and the mean observed error is less than 1.2 bar.Moreover,with such a strategy,faster response and less overshoot are possible,which should be regarded as significant advantages.

PRESSURE COMPENSATION METHOD OF UNDERWATER HYDRAULIC SYSTEM WITH HYDRAULIC POWER UNIT BEING UNDER ATMOSPHERIC CIRCUMSTANCE AND PRESSURE COMPENSATED VALVE

Based on the analysis of the-state-of-the-art of pressure compensation of underwater hydraulic systems （UHSs）, a new method of pressure compensation of UHSs, whose hydraulic power unit is in the atmospheric circumstance, is proposed. And a pilot-operated relief valve with pressure compensation is realized. The pressure compensation precision is guaranteed by direct detection. Its dynamic performance and stability are improved by a dynamic feedback. Theoretical study, simulation and experiment show that the pilot-operated relief valve with pressure compensation has a fine property of tracking underwater ambient pressure and meet the requirement of underwater ambient pressure compensation.

Wing crack model subjected to high hydraulic pressure and far field stresses and its numerical simulation

By considering the effect of hydraulic pressure filled in wing crack and the connected part of main crack on the stress intensity factor at wing crack tip, a new wing crack model exerted by hydraulic pressure and far field stresses was proposed. By introducing the equivalent crack length leq of wing crack, two terms make up the stress intensity factor KI at wing crack tip: one is the component for a single isolated straight wing crack of length 2l subjected to hydraulic pressure in wing crack and far field stresses, and the other is the component due to the effective shear stress induced by the presence of the equivalent main crack. The FEM model of wing crack propagation subjected to hydraulic pressure and far field stresses was also established according to different side pressure coefficients and hydraulic pressures in crack. The result shows that a good agreement is found between theoretical model of wing crack proposed and finite element method (FEM). In theory, an unstable crack propagation is shown if there is high hydraulic pressure and lateral tension. The wing crack model proposed can provide references for studying on hydraulic fracturing in rock masses.

Pressure-tracking control of a novel electro-hydraulic braking system considering friction compensation

This work presents an integrated pressure-tracking controller for a novel electro-hydraulic brake(EHB) system considering friction and hydraulic disturbances. To this end, a mathematical model of an EHB system, consisting of actuator and hydraulic sub-systems, is derived for describing the fundamental dynamics of the system and designing the controller. Due to sensor inaccuracy and measurement noise, a Kalman filter is constructed to estimate push rod stroke for generating desired master cylinder pressure. To improve pressure-tracking accuracy, a linear friction model is generated by linearizing the nonlinear Tustin friction model, and the unmodeled friction disturbances are assumed unknown but bounded. A sliding mode controller is designed for compensating friction disturbances, and the stability of the controller is investigated using the Lyapunov method. The performance of the proposed integrated controller is evaluated with a hardware-in-the-loop(HIL) test platform equipped with the EHB prototype. The test results demonstrate that the EHB system with the proposed integrated controller not only achieves good pressure-tracking performance, but also maintains robustness to friction disturbances.

Chloride ion penetration into concrete under hydraulic pressure

The lining concrete of subsea tunnel services under combined hydraulic pressure, mechanical and environmental loads. The chloride ion and water penetrations into concrete under hydraulic pressure were investigated. The experimental results indicate that the water penetration depth, chloride ion transportation depth, and the concentration of chloride ion ingression into concrete increase with raised hydraulic pressure and hold press period. But the chloride ion transportation velocity is only 53% of that of water when concrete specimens are under hydraulic pressure. The chloride transportation coefficient of concrete decreases with hold press period as power function. And that would increase 500% 600% in chloride transportation coefficient when the hydraulic pressure increases from 0 to 1.2 MPa. The hydraulic pressure also decreases the bound chloride ion of concrete to about zero. Besides, the low water-cementitions materials and suitable content of mineral admixture(including fly ash and slag) improve the resistance capacity of chloride penetration, and binding capacity of concrete under hydraulic pressure.