Hydrogen production from steam reforming of ethanol over Ni/MgO-CeO_2 catalyst at low temperature

MgO,CeO2 and MgO-CeO2 with different mole ratio of Mg:Ce were prepared by solid-phase burning method.Catalysts Ni/MgO,Ni/CeO2 and Ni/MgO-CeO2 were prepared by impregnation method.The catalytic properties were evaluated in ethanol steam reforming(ESR) reaction.Specific surface areas of the supports were measured by nitrogen adsorption-desorption at 77 K,and the catalysts were characterized with X-ray diffraction(XRD),temperature programmed reduction(TPR) and thermogravimetric(TG).The results showed that well...

Hydrogen production by steam reforming of ethanol over copper doped Ni/CeO_2 catalysts

High surface area CeO2 was prepared by the surfactant-assisted route and was employed as catalyst support. The 0-3 at.% Cu doped Cu-Ni/CeO2 catalysts with 10 wt.% and 15 wt.% of total metal loading were prepared by an impregnation-coprecipitation method. The influence of Cu atomic content on the catalytic performance was investigated on the steam reforming of ethanol （SRE） for H2 production and the catalysts were characterized by N2 adsorption, inductively coupled plasma （ICP）, X-ray diffraction （XRD）, transmission electron microscopy （TEM）, temperature-programmed rerduction （TPR） and H2-pulse chemisorption techniques. The activity and products distribution behaviors of the catalysts were significantly affected by the doped Cu molar content based on the promotion effect on the dispersion of NiO particles and the interactions between Cu-Ni metal and CeO2 support. Significant increase in the ethanol conversion and hydrogen selectivity were obtained when moderate Cu metal was doped into the Ni/CeO2 catalyst. Over both of the 10Ni98.5Cu1.5/CeO2 and 15Ni98.5Cu1.5/CeO2 catalysts, more than 80% of ethanol conversion and 60% of H2 selectivity were obtained in the ethanol steam-reforming when the reaction temperature was above 450 ℃.

Hydrogen generation from methanol reforming under unprecedented mild conditions

A homogeneous catalyst [Cp＊Rh（NH3）（H2O）2]-（3＋） has been found for the clean conversion of methanol and water to hydrogen and carbon dioxide. The simple and easily available reaction steps can circumvent the formation of CO, therefore, making it possible to avoid inactivating catalysts and contaminating the hydrogen fuel. Different from conventional reforming method for hydrogen production, no additional alkaline or organic substances are required in this method. Valuable hydrogen can be obtained under ambient pressure at 70 C, corresponding TOF is 83.2 h 1. This is an unprecedented success in reforming methanol to hydrogen. Effects of reaction conditions, such as reaction temperature, initial methanol concentration and the initial p H value of buffer solution on the hydrogen evolution are all systematically investigated. In a certain range, higher reaction temperature will accelerate reaction rate. The slightly acidic condition is conducive to rapid hydrogen production. These findings are of great significance to the present establishment of the carbon-neutral methanol economy.

La_2O_2CO_3 supported Ni-Fe catalysts for hydrogen production from steam reforming of ethanol

La2O2CO3 was prepared by calcination of La2 （CO3）3 in the air. Catalysts Ni-Fe/La2O2CO3 with different mole ratios of Ni to Fe, Ni/La2O2CO3 and Fe/La2O2CO3 were prepared by impregnation method. The catalytic properties were evaluated on steam reforming of ethanol （SRE） from 300 to 700 ℃ under atmospheric pressure and the samples were characterized by Brunauer-Emmett-Teller method （BET）, X-ray diffraction （XRD） and temperature programmed reduction （TPR）. The results showed that Ni-Fe bimetallic catalysts exhibited higher activities than single metallic catalysts, which was attributed to the co-existence of well dispersed Ni, Fe and LaFeyNi1-yO3. It was found that the catalyst Ni-Fe/La2O2CO3 containing 10 wt.% Ni and 3 wt.%-5 wt.% Fe showed the best performance, the conversion of ethanol was 100%, the selectivity of H2 was higher than 90%, and the selectivity of CO was lower than 1.5% at 400 ℃.

Microfibrous entrapped ZnO-CaO/Al_2O_3 for high efficiency hydrogen production via methanol steam reforming

Sinter-locked microfibrous networks consisting of -3 vol.% of 8 p.m （dia.） nickel microfibers have been utilized to entrap -30vo1.% of 100-200 μm dia. porous AI203. ZnO and CaO were then highly dispersed onto the pore surface of entrapped A1203 by the incipient wetness impregnation method. Due to the unique combination of surface area, pore size/particle size, thermal conductivity, and void volume, the resulting microfibrous catalyst composites provided significant improvement of catalytic bed reactivity and utilization efficiency when used in methanol steam reforming. Roughly 260 mL/min of reformate, comprising 〉70% H2, 〈5% CO and trace CH4, with 〉97% methanol conversion, could be produced in a I cm3 bed volume of our novel microfihrous entrapped ZnO-CaO/Al2O3 catalyst composite at 470℃ with a high weight hourly space velocity （WHSV） of 15 h-1 using steam/methanol （1.3/1） mixture as feedstock. Compared to a packed bed of 100-200μm ZnO-CaO/Al2O3, our composite bed provided a doubling of the reactor throughput with a halving of catalyst usage.