Hydrogen-induced amorphization of Zr-Cu-Ni-Al alloy

Arc melting was utilized in this study to produce Zr_(55)Cu_(30)Ni_5Al_(10) alloys under mixed atmospheres with various ratios of high-purity hydrogen to argon. The influences of hydrogen addition on the solidification structure and glass-forming ability of Zr_(55)Cu_(30)Ni_5Al_(10) alloy were determined by examining microstructures in different parts of the cast ingots. The results showed that different degrees of crystallization structures were obtained in the ascast button ingots after arc melting in high-purity Ar, and the cross-sectional solidification morphology of arcmelted ingots was found to consist of crystals with varying from the bottom up. By contrast, there were completely amorphous structures in the middle and upper areas of the as-cast button ingots fabricated by adding 10% H_2 to the high-purity Ar atmosphere. A clear solidification interface was found between the crystal and glass in the ascast button ingots, which indicates that hydrogen addition can enhance the Zr_(55)Cu_(30)Ni_5Al_(10) alloy's glass-forming ability. The precise mechanism responsible for this was also investigated.

Hydrogen-induced amorphization in LaNi_(3-x)Mn_x compounds

Effects of Mn content on the hydrogen-induced amorphization of LaNi3-xMnx(x=0.0,0.1,0.3 and 0.5) hydrogen storage alloys were studied systematically.All the alloys were prepared using a rapid quenching and annealing method.As the charging time increased,the hydrogen-induced amorphization occurred gradually in all the compounds for the first cycle.During the discharge process,discharge potential plateau was not observed in LaNi3.As Mn content increased,however,structural changes were inhibited partly,and a p...

Promoting amorphization of commercial TiO_(2) upon sodiation to boost the sodium storage performance

Anatase TiO_(2) is a promising anode material for sodium-ion batteries,yet the low electronic and ionic conductivities are the main obstacles for its practical application.Even though the amorphization of TiO_(2) upon sodiation has already been observed,its underneath mechanisms are not fully elucidated.Herein,a low-cost nitrogen-containing carbon source of polyacrylonitrile is adopted to modify commercial anatase TiO_(2) by a convenient and nontoxic ball-milling technique combined with subsequent annealing treatment.In particular,the employment of a nitrogen-doping approach accompanied by nitrogendoped carbon coating,results in a greatly improved conductivity,overall leading to a high reversible capacity of about 260 m A h g^(-1)at 25 m A g^(-1),superior rate capabilities,and an ultra-stable capacity of about 186 m A h g^(-1)after 1600 cycles at 500 m A g^(-1).Detailed characterizations denote that the improved conductivity as well as the small size of the synthesized TiO_(2) grains play a key role in the TiO_(2) amorphization upon sodiation,with the TiO_(2)/C nanocomposite undergoing a complete amorphization in just few cycles.Finally,the irreversible amorphization of TiO_(2) is confirmed to be a crucial ingredient facilitating the Na+diffusion kinetics and pseudocapacitive behavior,thus boosting the sodium storage performance.

Polyetherketoneketone/carbon fiber composites with an amorphous interface prepared by solution impregnation

Interfacial adhesion between carbon fibers(CF)and polyetherketoneketone(PEKK)is a key factor that affects the mechanical performances of their composites.It is therefore of great importance to impregnate the CF bundles with PEKK as effi-ciently as possible.We report that PEKK with a good dispersion in a mixed solution of 4-chlorophenol and 1,2-dichloroethane can be introduced onto CF surfaces by solution impregnation and curing at 280,320,340 and 360℃.The excellent wettability or infiltra-tion of the PEKK solution guarantees a full covering and its tight binding to CFs,making it possible to evaluate the interfacial shear strength(IFSS)with the microdroplet method.The interior of the CF bundles is completely and uniformly filled with PEKK by solu-tion impregnation,leading to a high interlaminar shear strength(ILSS).The maximum IFSS and ILSS reached 107.8 and 99.3 MPa,respectively.Such superior shear properties are ascribed to the formation of amorphous PEKK in the small spaces between CFs.

Macroporous Directed and Interconnected Carbon Architectures Endow Amorphous Silicon Nanodots as Low‑Strain and Fast‑Charging Anode for Lithium‑Ion Batteries

Fabricating low-strain and fast-charging silicon-carbon composite anodes is highly desired but remains a huge challenge for lithium-ion batteries.Herein,we report a unique silicon-carbon composite fabricated by uniformly dis-persing amorphous Si nanodots(SiNDs)in carbon nanospheres(SiNDs/C)that are welded on the wall of the macroporous carbon framework(MPCF)by vertical graphene(VG),labeled as MPCF@VG@SiNDs/C.The high dispersity and amor-phous features of ultrasmall SiNDs(~0.7 nm),the flexible and directed electron/Li+transport channels of VG,and the MPCF impart the MPCF@VG@SiNDs/C more lithium storage sites,rapid Li+transport path,and unique low-strain property during Li+storage.Consequently,the MPCF@VG@SiNDs/C exhibits high cycle stability(1301.4 mAh g^(-1) at 1 A g^(-1) after 1000 cycles without apparent decay)and high rate capacity(910.3 mAh g^(-1),20 A g^(-1))in half cells based on industrial electrode standards.The assembled pouch full cell delivers a high energy density(1694.0 Wh L^(-1);602.8 Wh kg^(-1))and an excellent fast-charging capability(498.5 Wh kg^(-1),charging for 16.8 min at 3 C).This study opens new possibilities for preparing advanced silicon-carbon com-posite anodes for practical applications.

Achieving Negatively Charged Pt Single Atoms on Amorphous Ni(OH)_(2)Nanosheets with Promoted Hydrogen Absorption in Hydrogen Evolution

Single-atom(SA)catalysts with nearly 100%atom utilization have been widely employed in electrolysis for decades,due to the outperforming catalytic activity and selectivity.However,most of the reported SA catalysts are fixed through the strong bonding between the dispersed single metallic atoms with nonmetallic atoms of the substrates,which greatly limits the controllable regulation of electrocatalytic activity of SA catalysts.In this work,Pt-Ni bonded Pt SA catalyst with adjustable electronic states was successfully constructed through a controllable electrochemical reduction on the coordination unsaturated amorphous Ni(OH)_(2)nanosheet arrays.Based on the X-ray absorption fine structure analysis and first-principles calculations,Pt SA was bonded with Ni sites of amorphous Ni(OH)_(2),rather than conventional O sites,resulting in negatively charged Pt^(δ-).In situ Raman spectroscopy revealed that the changed configuration and electronic states greatly enhanced absorbability for activated hydrogen atoms,which were the essential intermediate for alkaline hydrogen evolution reaction.The hydrogen spillover process was revealed from amorphous Ni(OH)_(2)that effectively cleave the H-O-H bond of H_(2)O and produce H atom to the Pt SA sites,leading to a low overpotential of 48 mV in alkaline electrolyte at-1000 mA cm^(-2)mg^(-1)_(Pt),evidently better than commercial Pt/C catalysts.This work provided new strategy for the control-lable modulation of the local structure of SA catalysts and the systematic regulation of the electronic states.

Progress and prospects of Mg-based amorphous alloys in azo dye wastewater treatment

Mg-based amorphous alloys exhibit efficient catalytic performance and excellent biocompatibility with a promising application probability,specifically in the field of azo dye wastewater degradation.However,the problems like difficulty in preparation and poor cycling stability need to be solved.At present,Mg-based amorphous alloys applied in wastewater degradation are available in powder and ribbon.The amorphous alloy powder fabricated by ball milling has a high specific surface area,and its reactivity is thousands of times better than that of gas atomized alloy powder.But the development is limited due to the high energy consumption,difficult and costly process of powder recycling.The single roller melt-spinning method is a new manufacturing process of amorphous alloy ribbon.Compared to amorphous powder,the specific surface area of amorphous ribbon is relatively lower,therefore,it is necessary to carry out surface modification to enhance it.Dealloying is a way that can form a pore structure on the surface of the amorphous alloys,increasing the specific surface area and providing more reactive sites,which all contribute to the catalytic performance.Exploring the optimal conditions for Mg-based amorphous alloys in wastewater degradation by adjusting amorphous alloy composition,choosing suitable method to preparation and surface modification,reducing cost,expanding the pH range will advance the steps to put Mg-based amorphous alloys in industrial environments into practice.

Nitrogen-Doped Amorphous Carbon Homojunction from Palmyra Sugar as a Renewable Solar Cell

An a-C/a-C:N junction,which used palmyra sugar as the carbon source and ammonium hydroxide(NH4OH)as the dopant source,was successfully deposited on the ITO glass substrate using the nano-spraying method.The current-voltage relationship of the junction was found to be a Schottky-like contact,and therefore the junction shows the characteristic rectifiers.This means the a-C and a-C:N are semiconductors with different types of conduction.Moreover,the samples showed an increase in current and voltage value when exposed to visible light(bright state)compared to the dark condition,thereby,indicating the creation of electron-hole pairs during the exposure.It was also discovered that the relationship between current and voltage for the a-C/a-C:N junction sample formed a curve that satisfies the rule of the photovoltaic effect when exposed to visible light from a light bulb.The exposure of this sample to direct sunlight at AM 1.5 conditions produced a curve that meets the rules for the emergence of the photovoltaic effect with higher characteristics for the current-voltage relationship.Thus,the a-C/a-C:N junction sample is a solar cell successfully fabricated using a sample method and has a maximum efficiency of 0.0013%.

Amorphous Iridium Oxide-Integrated Anode Electrodes with Ultrahigh Material Utilization for Hydrogen Production at Industrial Current Densities

Herein,ionomer-free amorphous iridium oxide(IrO_(x))thin electrodes are first developed as highly active anodes for proton exchange membrane electrolyzer cells(PEMECs)via low-cost,environmentally friendly,and easily scalable electrodeposition at room temperature.Combined with a Nafion 117 membrane,the IrO_(x)-integrated electrode with an ultralow loading of 0.075 mg cm^(-2)delivers a high cell efficiency of about 90%,achieving more than 96%catalyst savings and 42-fold higher catalyst utilization compared to commercial catalyst-coated membrane(2 mg cm^(-2)).Additionally,the IrO_(x)electrode demonstrates superior performance,higher catalyst utilization and significantly simplified fabrication with easy scalability compared with the most previously reported anodes.Notably,the remarkable performance could be mainly due to the amorphous phase property,sufficient Ir^(3+)content,and rich surface hydroxide groups in catalysts.Overall,due to the high activity,high cell efficiency,an economical,greatly simplified and easily scalable fabrication process,and ultrahigh material utilization,the IrO_(x)electrode shows great potential to be applied in industry and accelerates the commercialization of PEMECs and renewable energy evolution.

Mesoporous amorphous FeOOH-encapsulated BiO_(2–x) photocatalyst with harnessing broad spectrum toward activation of persulfate for tetracycline degradation

With the growing concern about the water environment,the advanced oxidation process of persulfate activation assisted by photocatalysis has attracted considerable attention to decompose dissolved organic micropollutants.In this work,to overcome the drawbacks of the photocatalytic activity reduction caused by the photo-corrosion of non-stoichiometric BiO_(2–x),a novel material with amorphous FeOOH in situ grown on layered BiO_(2–x) to form a core-shell structure similar to popcorn chicken-like morphology was produced in two simple and environmentally beneficial steps.Through a series of degradation activity tests of hybrid materials under different conditions,the as-prepared materials exhibited remarkable degradation activity and stability toward tetracycline in the FeOOH@BiO_(2–x)/Vis/PS system due to the synergism of photocatalysis and persulfate activation.The results of XRD,SEM,TEM,XPS,FTIR,and BET show that the loading of FeOOH increases the specific surface area and active sites appreciably;the heterogeneous structure formed by FeOOH and BiO_(2–x) is more favorable to the effective separation of photogenerated carriers.The optimal degradation conditions were at a catalyst addition of 0.7 g·L^(–1),a persulfate concentration of 1.0 g·L^(–1),and an initial pH of 4.5,at which the degradation rate could reach 94.7%after 90 min.The influence of typical inorganic anions on degradation was also examined.ESR studies and radical quenching experiments revealed that·OH,SO_(4)^(-)·,and·O_(2)^(-)were the principal active species generated during the degradation of tetracycline.The results of the 1,10-phenanthroline approach proved that the effect of dissolved iron ions on the tetracycline degradation was limited,and the interfacial reaction that occurs on the active sites on the material's surface was a critical factor.This work provides a novel method for producing efficient broad-spectrum Bismuth-based composite photocatalysts and photocatalytic-activated persulfate synergistic degradation of tetracycline.

Anelasticity to plasticity transition in a model two-dimensional amorphous solid

Anelasticity, as an intrinsic property of amorphous solids, plays a significant role in understanding their relaxation and deformation mechanism. However, due to the lack of long-range order in amorphous solids, the structural origin of anelasticity and its distinction from plasticity remain elusive. In this work, using frozen matrix method, we study the transition from anelasticity to plasticity in a two-dimensional model glass. Three distinct mechanical behaviors, namely,elasticity, anelasticity, and plasticity, are identified with control parameters in the amorphous solid. Through the study of finite size effects on these mechanical behaviors, it is revealed that anelasticity can be distinguished from plasticity.Anelasticity serves as an intrinsic bridge connecting the elasticity and plasticity of amorphous solids. Additionally, it is observed that anelastic events are localized, while plastic events are subextensive. The transition from anelasticity to plasticity is found to resemble the entanglement of long-range interactions between element excitations. This study sheds light on the fundamental nature of anelasticity as a key property of element excitations in amorphous solids.

Kinetic-boosted CO_(2) electroreduction to formate via synergistic electric-thermal field on hierarchical bismuth with amorphous layer

Electrocatalytic converting CO_(2) into chemical products has emerged as a promising approach to achieving carbon neutrality.Herein,we report a bismuth-based catalyst with high curvature terminal and amorphous layer which fabricated via two-step electrodeposition achieves stable formate output in a wide voltage window of 600 mV.The Faraday efficiency(FE) of formate reached up to 99.4% at-0.8 V vs.RHE and it remained constant for more than 92 h at-15 mA cm^(-2).More intriguingly,FE formate of95.4% can be realized at a current density of industrial grade(-667.7 mA cm^(-2)) in flow cell.The special structure promoted CO_(2) adsorption and reduced its activation energy and enhanced the electric-thermal field and K^(+) enrichment which accelerated the reaction kinetics.In situ spectroscopy and theoretical calculation further confirmed that the introduction of amorphous structure is beneficial to adsorpting CO_(2)and stabling*OCHO intermediate.This work provides special insights to fabricate efficient electrocatalysts by means of structural and crystal engineering and makes efforts to realize the industrialization of bismuth-based catalysts.

Research of caged dynamics of clusters center atoms in Pd_(82)Si_(18) amorphous alloy

To date,there is still a lack of a comprehensive explanation for caged dynamics which is regarded as one of the intricate dynamic behaviors in amorphous alloys.This study focuses on Pd_(82)Si_(18)as the research object to further elucidate the underlying mechanism of caged dynamics from multiple perspectives,including the cage's lifetime,atomic local environment,and atomic potential energy.The results reveal that Si atoms exhibit a pronounced cage effect due to the hindrance of Pd atoms,resulting in an anomalous peak in the non-Gaussian parameters.An in-depth investigation was conducted on the caged dynamics differences between fast and slow Si atoms.In comparison to fast Si atoms,slow Si atoms were surrounded by more Pd atoms and occupied lower potential energy states,resulting in smaller diffusion displacements for the slow Si atoms.Concurrently,slow Si atoms tend to be in the centers of smaller clusters with coordination numbers of 9 and 10.During the isothermal relaxation process,clusters with coordination numbers 9 and 10 have longer lifetimes,suggesting that the escape of slow Si atoms from their cages is more challenging.The findings mentioned above hold significant implications for understanding the caged dynamics.

Microstructure evolution of Ti_(48)Zr_(27)Cu_(6)Nb_(5)Be_(14)amorphous alloy after semi-solid isothermal treatment

The as-cast amorphous Ti_(48)Zr_(27)Cu_(6)Nb_(5)Be_(14)composites,comprising in situ formedβ-Ti ductile crystalline precipitates,were prepared by water cooled copper mold suction casting.Then,the semi-solid composites were obtained after the as-cast composites were treated by semi-solid isothermal treatment.The microstructure evolution and kinetics of the composites were examined.Results show that the microstructures of both the as-cast and semi-solid composites comprise ofβ-Ti crystal phases and amorphous matrix phases.Before and after treatment,the crystals evolve from fine granular or fine dendritic crystals to coarse crystals.As the treatment temperature increasing or the time prolonging,the average crystal size gradually increases and the surface morphology of the crystals gradually becomes regular.By studying the microstructural evolution and dynamics during the isothermal treatment process,it is found that the final morphology ofβ-Ti crystals is influenced by the isothermal treatment temperature and time(t),and theβ-Ti evolution rate increases with an increase in treatment temperature.In addition,a linear relationship was observed between the size of cubicβ-Ti crystals(D^(3))and t;the growth kinetics factor K is 3.8μm^(3)·s^(-1).As the K value closes to 4μm^(3)·s^(-1),it is inferred the morphology evolution ofβ-Ti crystals is a coarsening behavior controlled by the diffusion of solute elements.

基于坐标优化的FOA-Amorphous节点定位算法

节点的位置信息在无线传感器网络的定位中起着至关重要的作用,而Amorphous算法的节点定位精度低。针对影响Amorphous定位精度的主要原因分析,提出了一种基于坐标优化的FOA-Amorphous节点定位算法。首先,引入多通信半径的概念细化节点跳数,利用网络平均连通度对节点的平均跳距进行重算;然后,以极大似然估计法得到的未知节点坐标值为果蝇优化算法中各果蝇的初始位置,通过此初始位置产生每个果蝇的初始种群,代入适应度函数求得当前果蝇的最佳位置,引入了个体认知因子c 1和群体引导因子c 2,优化了果蝇随机搜索的距离和方向,使得算法快速收敛到全局最优,避免算法早熟,提高了算法的收敛精度,通过迭代找到最佳未知节点位置坐标。与双通信半径算法、PSO-IDV-Hop算法以及Amorphous算法相比,该算法的归一化定位误差分别降低了约7%、23%和44%。

Effect of nanosized NbC precipitates on hydrogen-induced cracking of high-strength low-alloy steel

We investigated the effect of nanosized NbC precipitates on hydrogen-induced cracking(HIC)of high-strength low-alloy steel by conducting slow-strain-rate tensile tests(SSRT)and performing continuous hydrogen charging and fracture analysis.The results reveal that the HIC resistance of Nb-bearing steel is obviously superior to that of Nb-free steel,with the fractured Nb-bearing steel in the SSRT exhibiting a smaller ratio of elongation reduction(Iδ).However,as the hydrogen traps induced by NbC precipitates approach hydrogen saturation,the effect of the precipitates on the HIC resistance attenuate.We speculate that the highly dispersed nanosized NbC precipitates act as irreversible hydrogen traps that hinder the accumulation of hydrogen at potential crack nucleation sites.In addition,much like Nb-free steel,the Nb-bearing steel exhibits both H-solution strengthening and the resistance to HIC.

Krypton ion irradiation-induced amorphization and nano-crystal formation in pyrochlore Lu_2Ti_2O_7 at room temperature

Polycrystalline pyrochlore Lu2Ti2O7 pellets are irradiated with 600-keV Kr^3＋ions up to a fluence of 1.45 ×10^16Kr^3＋/cm^2. Irradiation induced structural modifications are examined by using grazing incidence x-ray diffraction（GIXRD） and cross-sectional transmission electron microscopy（TEM）. The GIXRD reveals that amorphous fraction increases with the increase of fluences up to 2 × 10^15Kr^3＋/cm^2, and the results are explained with a direct-impact model.However, when the irradiation fluence is higher than 2 × 10^15Kr^3＋/cm^2, the amorphous fraction reaches a saturation of-80%. Further TEM observations imply that nano-crystal is formed with a diameter of -10 nm within the irradiation layer at a fluence of 4 × 10^15Kr^3＋/cm^2. No full amorphization is achieved even at the highest fluence of 1.45 × 10^16Kr^3＋/cm^2（-36 displacement per atom）. The high irradiation resistance of pyrochlore Lu2Ti2O7 at higher fluence is explained on the basis of enhanced radiation tolerance of nano-crystal structure.

AMORPHIZATION TRANSFORMATION BY MECHANICAL ALLOYING IN THE Mo-Si SYSTEM

Starting from elemental powders, complete MoSi2 powder forms abruptly between 3.5and 4 h during mechanical alloying (MA) of the Mo-66 at.% Si powders. Continuous milling of this MoSi2 Phase leads to a nanocrystalline powder and amorphizationtransformation takes place after 100 h milling. Howeven MA of the Mo-37.5 at.%Si powders does not result in the formation of the Mo5Si3 crystalline phase, but the formation of a Mo(Si) supersaturated solid solution (SSS) and a completely amorphots phase after 5 h and 70 h milling, respectively. The free energy of the Mo-Sisystem has been calculated and it has been found that there is no driving force for the amorphization reaction under normal conditions. The amorphization by MA of the Mo-Si system is attributed to a solid-state amorphization reaction in which defects and a very fine grain size induced during milling process may raise the free energy of the crystalline intermetallic phase (for MoSi2) or the Mo(Si) supersaturated solid solution (for Mo5Si3) above that of the amorphous phase.

AMORPHIZATION IN Nb-M (M=Fe, Co, Ni) BINARY METAL SYSTEMS INDUCED BY ION BEAM ASSISTED DEPOSITION (IBAD)

Ion beam assisted deposition technique (IBAD) was utilized to systematically study amorphization in binary metal systems of Nb-magnetic element, i.e., Nb-M (M=Fe, Co or Ni). The glass forming range termed as Nb fraction of Nb-Fe system was about 34at.% to 56at.%, that of Nb-Co system was about 32at.% to 72at.% and that of Nb-Ni about 20at. % to 80at. %. Similar percolation patterns were found in amorphous alloy films. The fractal dimensions of the percolation patterns approach to 2, which indicates 2-D layer growth for amorphous phases. It is regarded that the assisted Ar+ ion beam during the deposition process plays important role for the 2-D layer growth. Some metastable crystalline phases were obtained in these three systems by IBAD, e.g., bcc supersaturated solid solutions in Nb-Fe and Nb-Co systems, fcc and hcp phases in Nb-Co and Nb-Ni systems. The formation and competing between the amorphous and the metastable crystalline phases were determined by both the phases' thermodynamic states in binary metal systems and kinetics during IBAD process.

Amorphization activated FeB_(2) porous nanosheets enable efficient electrocatalytic N_(2) fixation

Designing active,robust and cost-effective catalysts for the nitrogen reduction reaction(NRR) is of paramount significance for sustainable electrochemical NH3 synthesis.Transition-metal diborides(TMB_2)have been recently theoretically predicted to be a new class of potential NRR catalysts,but direct experimental evidence is still lacking.Herein,we present the first experimental demonstration that amorphous FeB_2 porous nanosheets(a-FeB_2 PNSs) could be a highly efficient NRR catalyst,which exhibited an NH3 yield of 39.8 μg h^(-1) mg^(-1)(-0.3 V) and a Faradaic efficiency of 16.7%(-0.2 V),significantly outperforming their crystalline counterpart and most of existing NRR catalysts.First-principle calculations unveiled that the amorphization could induce the upraised d-band center of a-FeB_2 to boost d-2π~* coupling between the active Fe site and ~*N_2 H intermediate,resulting in enhanced ~*N_2 H stabilization and reduced reaction barrier.Out study may facilitate the development and understanding of earth-abundant TMB_2-based catalysts for electrocatalytic N_2 fixation.