Fabrication of Silane and Desulfurization Ash Composite Modified Polyurethane and Its Interfacial Binding Mechanism

Polyurethane/desulfurization ash(PU/DA)composites were synthesized using"one-pot method",with the incorporation of a silane coupling agent(KH550)as a"molecular bridge"to facilitate the integration of DA as hard segments into the PU molecular chain.The effects of DA content(φ)on the mechanical properties,thermal stability,and hydrophobicity of PU,both before and after the addition of KH550,were thoroughly examined.The results of microscopic mechanism analysis confirmed that KH550 chemically modified the surface of DA,facilitating its incorporation into the polyurethane molecular chain,thereby significantly enhancing the compatibility and dispersion of DA within the PU matrix.When the mass fraction of modified DA(MDA)reached 12%,the mechanical properties,thermal stability,and hydrophobicity of the composites were substantially improved,with the tensile strength reaching 14.9 MPa,and the contact angle measuring 100.6°.

Reconcile the contradictory wettability requirements for the reduction and oxidation half-reactions in overall CO_(2) photoreduction via alternately hydrophobic surfaces

The overall photocatalytic CO_(2) reduction reaction(OPCRR)that can directly convert CO_(2) and H_(2)O into fuels represents a promising renewable energy conversion technology.As a typical redox reaction,the OPCRR involves two half-reactions:the CO_(2) reduction half-reaction(CRHR)and the water oxidation half-reaction(WOHR).Generally,both half-reactions can be promoted by adjusting the wettability of catalysts.However,there is a contradiction in wettability requirements for the two half-reactions.Specifically,CRHR prefers a hydrophobic surface that can accumulate more CO_(2) molecules on the active sites,ensuring the appropriate ratio of gas-phase(CO_(2))to liquid-phase(H_(2)O)reactants.Conversely,the WOHR prefers a hydrophilic surface that can promote the departure of the gaseous product(O_(2))from the catalyst surface,preventing isolation between active sites and the reactant(H_(2)O).Here,we successfully reconciled the contradictory wettability requirements for the CRHR and WOHR by creating an alternately hydrophobic catalyst.This was achieved through a selectively hydrophobic modification method and a charge-transfer-control strategy.Consequently,the collaboratively promoted CRHR and WOHR led to a significantly enhanced OPCRR with a solar-to-fuel conversion efficiency of 0.186%.Notably,in ethanol production,the catalyst exhibited a 10.64-fold increase in generation rate(271.44μmol g^(-1)h~(-1))and a 4-fold increase in selectivity(55.77%)compared to the benchmark catalyst.This innovative approach holds great potential for application in universal overall reactions involving gas participation.

Self-propelled Leidenfrost droplets on femtosecond-laser-induced surface with periodic hydrophobicity gradient

The controllable transfer of droplets on the surface of objects has a wide application prospect in the fields of microfluidic devices,fog collection and so on.The Leidenfrost effect can be utilized to significantly reduce motion resistance.However,the use of 3D structures limits the widespread application of self-propulsion based on Leidenfrost droplets in microelectromechanical system.To manipulate Leidenfrost droplets,it is necessary to create 2D or quasi-2D geometries.In this study,femtosecond laser is applied to fabricate a surface with periodic hydrophobicity gradient(SPHG),enabling directional self-propulsion of Leidenfrost droplets.Flow field analysis within the Leidenfrost droplets reveals that the vapor layer between the droplets and the hot surface can be modulated by the SPHG,resulting in directional propulsion of the inner gas.The viscous force between the gas and liquid then drives the droplet to move.

Construction of Self-Assembly Based Tunable Absorber:Lightweight,Hydrophobic and Self-Cleaning Properties

Although multifunctional aerogels are expected to be used in applications such as portable electronic devices,it is still a great challenge to confer multifunctionality to aerogels while maintaining their inherent microstructure.Herein,a simple method is proposed to prepare multifunctional NiCo/C aerogels with excellent electromagnetic wave absorption properties,superhydrophobicity,and self-cleaning by water-induced NiCo-MOF self-assembly.Specifically,the impedance matching of the three-dimensional(3D)structure and the interfacial polarization provided by CoNi/C as well as the defect-induced dipole polarization are the primary contributors to the broadband absorption.As a result,the prepared NiCo/C aerogels have a broadband width of 6.22 GHz at 1.9 mm.Due to the presence of hydrophobic functional groups,CoNi/C aerogels improve the stability in humid environments and obtain hydrophobicity with large contact angles>140°.This multifunctional aerogel has promising applications in electromagnetic wave absorption,resistance to water or humid environments.

Fabrication of polyetheretherketone(PEEK)-based 3D electronics with fine resolution by a hydrophobic treatment assisted hybrid additive manufacturing method

Additive manufacturing(AM)is a free-form technology that shows great potential in the integrated creation of three-dimensional(3D)electronics.However,the fabrication of 3D conformal circuits that fulfill the requirements of high service temperature,high conductivity and high resolution remains a challenge.In this paper,a hybrid AM method combining the fused deposition modeling(FDM)and hydrophobic treatment assisted laser activation metallization(LAM)was proposed for manufacturing the polyetheretherketone(PEEK)-based 3D electronics,by which the conformal copper patterns were deposited on the 3D-printed PEEK parts,and the adhesion between them reached the 5B high level.Moreover,the 3D components could support the thermal cycling test from-55℃ to 125℃ for more than 100 cycles.Particularly,the application of a hydrophobic coating on the FDM-printed PEEK before LAM can promote an ideal catalytic selectivity on its surface,not affected by the inevitable printing borders and pores in the FDM-printed parts,then making the resolution of the electroless plated copper lines improved significantly.In consequence,Cu lines with width and spacing of only60μm and 100μm were obtained on both as-printed and after-polished PEEK substrates.Finally,the potential of this technique to fabricate 3D conformal electronics was demonstrated.

Reduced graphene oxide aerogel decorated with Mo_(2)C nanoparticles toward multifunctional properties of hydrophobicity,thermal insulation and microwave absorption

Reduced graphene oxide(rGO)aerogels are emerging as very attractive scaffolds for high-performance electromagnetic wave absorption materials(EWAMs)due to their intrinsic conductive networks and intricate interior microstructure,as well as good compatibility with other electromagnetic(EM)components.Herein,we realized the decoration of rGO aerogel with Mo_(2)C nanoparticles by sequential hydrothermal assembly,freeze-drying,and high-temperature pyrolysis.Results show that Mo_(2)C nanoparticle loading can be easily controlled by the ammonium molybdate to glucose molar ratio.The hydrophobicity and thermal insulation of the rGO aerogel are effectively improved upon the introduction of Mo_(2)C nanoparticles,and more importantly,these nanoparticles regulate the EM properties of the rGO aerogel to a large extent.Although more Mo_(2)C nanoparticles may decrease the overall attenuation ability of the rGO aerogel,they bring much better impedance matching.At a molar ratio of 1:1,a desirable balance between attenuation ability and impedance matching is observed.In this context,the Mo_(2)C/r GO aerogel displays strong reflection loss and broad response bandwidth,even with a small applied thickness(1.7 mm)and low filler loading(9.0wt%).The positive effects of Mo_(2)C nanoparticles on multifunctional properties may render Mo_(2)C/r GO aerogels promising candidates for high-performance EWAMs under harsh conditions.

Improving the anti-collapse performance of water-based drilling fluids of Xinjiang Oilfield using hydrophobically modified silica nanoparticles with cationic surfactants

Wellbore instability,especially drilling with water-based drilling fluids(WBDFs)in complex shale for-mations,is a critical challenge for oil and gas development.The purpose of this paper is to study the feasibility of using hydrophobically modified silica nanoparticle(HMN)to enhance the comprehensive performance of WBDFs in the Xinjiang Oilfield,especially the anti-collapse performance.The effect of HMN on the overall performance of WBDFs in the Xinjiang Oilfield,including inhibition,plugging,lu-bricity,rheology,and filtration loss,was studied with a series of experiments.The mechanism of HMN action was studied by analyzing the changes of shale surface structure and chemical groups,wettability,and capillary force.The experimental results showed that HMN could improve the performance of WBDFs in the Xinjiang Oilfeld to inhibit the hydration swelling and dispersion of shale.The plugging and lubrication performance of the WBDFs in the Xinjiang Oilfield were also enhanced with HMN based on the experimental results.HMN had less impact on the rheological and filtration performance of the WBDFs in the Xinjiang Oilfield.In addition,HMN significantly prevented the decrease of shale strength.The potential mechanism of HMN was as follows.The chemical composition and structure of the shale surface were altered due to the adsorption of HMN driven by electrostatic attraction.Changes of the shale surface resulted in significant wettability transition.The capillary force of the shale was converted from a driving force of water into the interior to a resistance.In summary,hydrophobic nanoparticles presented afavorable application potential for WBDFs.

Synergistic effects of dodecane-castor oil acid mixture on the flotation responses of low-rank coal:A combined simulation and experimental study

The utilization of an appropriate collector or surfactant is crucial for the beneficiation of low-rank coal.However,in previous studies,the selection of surfactants was primarily based on flotation procedures,which hinders the understanding of the interaction mechanism between surfactant groups and oxygen-containing functional groups at the surface of low-rank coal.In this study,we investigate the flotation of low-rank coal in the presence of a composite collector by using a combined theoretical and experimental approach.The maximum flotation mass recovery achieved was 82.89%using a 3:1 mixture of dodecane and castor oil acid.Fourier-transform infrared and X-ray photoelectron spectroscopic analyses showed that castor oil acid was effectively adsorbed onto the surface of low-rank coal,enhancing the hydrophobicity of the coal.In addition,the diffusion coefficient of water molecules in the water-composite collector-coal system was greater than that in the dodecane system.Moreover,due to the presence of castor oil acid in the flotation process,the adsorption distance of dodecane and low-rank coal became shorter.Molecular dynamics simulations revealed that the diffusion and interaction of surfactant molecules at the interface of low-rank coal particles and water was enhanced because the adsorption of the dodecane-castor oil acid mixture is primarily controlled by hydrogen bonds and electrostatic attraction.Based on these results,a better surfactant for flotation of low-rank coal is also proposed.

Synergistic activation of smithsonite with copper-ammonium species for enhancing surface reactivity and xanthate adsorption

Copper ions(Cu^(2+))are usually added to activate the sulfidized surface of zinc oxide minerals to enhance xanthate attachment using sulfidization xanthate flotation technology.The adsorption of Cu^(2+)and xanthate on the sulfidized surface was investigated in various systems,and its effect on the surface hydrophobicity and flotation performance was revealed by multiple analytical methods and experiments.X-ray photoelectron spectroscopy(XPS)and time-of-flight secondary ion mass spectrometry(To F-SIMS)characterization demonstrated that the adsorption of Cu^(2+)on sulfidized smithsonite surfaces increased the active Cu—S content,regardless of treatment in any activation system.The sulfidized surface pretreated with NH_(4)^(+)-Cu^(2+)created favorable conditions for the adsorption of more Cu^(2+),significantly enhancing the smithsonite reactivity.Zeta potential determination,ultraviolet(UV)-visible spectroscopy,Fourier transform-infrared(FT-IR)measurements,and contact angle detection showed that xanthate was chemically adsorbed on the sulfidized surface,and its adsorption capacity in various systems was illustrated from qualitative and quantitative aspects.In comparison to the Na2S–Cu^(2+)and Cu^(2+)–Na2S–Cu^(2+)systems,xanthate exhibited a higher adsorption capacity on sulfidized smithsonite surfaces in NH_(4)^(+)-Cu^(2+)–Na2S–Cu^(2+)system.Hence,activation with Cu^(2+)–NH4+synergistic species prior to sulfidization significantly enhanced the mineral surface hydrophobicity,thereby increasing its flotation recovery.

Fabrication of hydrophobic Pd/Al_(2)O_(3)-phosphoric acid via P-O-Al bond for liquid hydrogenation reaction

Alumina(Al_(2)O_(3))is widely used in the chemical industry as the catalyst and support due to its high specific surface area,abundant pore size distribution and chemical stability.However,the occurrence of hydration in water environment,result in outstanding decrease in specific surface area and collapse of pore structure.In this work,dodecyl phosphoric acid(PA)is used to modify the surface of Al_(2)O_(3)to obtain a series of hydrophobic material(Al_(2)O_(3)-PA).Based on XPS and NMR analysis,PA is chemically bonded on Al_(2)O_(3)to form PAOAAl bond.Furthermore,BET and WCA results display that Al_(2)O_(3)-1PA exhibits excellent the hydrophobicity and hydrothermal stability while maintains the pore structure.Take it as the substrate to support the Pd nanoparticles,the as-prepared Pd/Al_(2)O_(3)-PA shows the superior catalytic performance in the hydrogenation of phenol and anthraquinone relative to Pd/Al_(2)O_(3),indicating the accessibility of Pd sites after PA modification.Especially,the significantly enhanced stability is also obtained in four cycles for aqueous phenol hydrogenation.This can be ascribed that the PA modification inhibits the aggregation of Pd nanoparticles and the products adhesion in the reaction process.The extension of PA coatings to monolithic catalysts could expand their current capabilities in industrial applications and warrants ongoing investigation.

Surface hydrophobic modification of MXene to promote the electrochemical conversion of N_(2) to NH_(3)

Hydrophobic treatment of the catalyst surfaces can suppress the competitive hydrogen evolution reaction(HER) during the nitrogen reduction reaction(NRR).In this work,the surface of Ti_(3)C_(2)Ti_(x) MXene is modified by cetyltrimethylammonium bromide(CTAB) and trimethoxy(3,3,4,4,5,5,6,6,7,7,8,8,8-trideca fluorooctyl) silane(FOTS) to increase the hydrophobicity of MXenes.The ammonia(NH_(3)) production rate and faradaic efficiency(FE) are improved from 37.62 to 54.01 μg h^(-1)mg_(cat)^(-1).and 5.5% to 18.1% at-0.7 V vs.RHE,respectively after surface modification.^(15)N isotopic labeling experiment confirms that nitrogen in produced ammonia originates from N_(2) in the electrolyte.The excellent NRR activity of surface hydrophobic MXenes is mainly due to surfactant molecules,which inhibit the entry of water molecules and the competitive HER,which have been verified by in situ FT-IR,DFT and molecular dynamics calculations.This strategy provides an ingenious method to design more active NRR electrocatalysts.

Cerium Methacrylate Assisted Preparation of Highly Thermally Conductive and Anticorrosive Multifunctional Coatings for Heat Conduction Metals Protection

Preparing polymeric coatings with well corrosion resistance and high thermal conductivity(TC)to prolong operational life and ensure service reliability of heat conductive metallic materials has long been a substantive and urgent need while a difficult task.Here we report a multifunctional epoxy composite coating(F-CB/CEP)by synthesizing cerium methacrylate and ingeniously using it as a novel curing agent with corrosion inhibit for epoxy resin and modifier for boron nitride through"cation-π"interaction.The prepared F-CB/CEP coating presents a high TC of 4.29 W m^(−1)K^(−1),which is much higher than other reported anti-corrosion polymer coatings and thereby endowing metal materials coated by this coating with outstanding thermal management performance compared with those coated by pure epoxy coating.Meanwhile,the low-frequency impedance remains at 5.1×10^(11)Ωcm^(2)even after 181 days of immersion in 3.5 wt%NaCl solution.Besides,the coating also exhibits well hydrophobicity,self-cleaning properties,temperature resistance and adhesion.This work provides valuable insights for the preparation of high-performance composite coatings with potential to be used as advanced multifunctional thermal management materials,especially for heat conduction metals protection.

Can rainfall seasonality trigger soil water repellency in a tropical riparian forest?

Though riparian areas generally have a shallow water table and higher soil moisture compared to up slope areas,climatic seasonality may trigger water repellency in tropical riparian forests,which,if persistent,could negatively affect essential ecosystem functions related to water resources protection such as reduced overland-flow,sediment transport,and nutrient filtration.The objective of this study was to answer the following:can tropical riparian forests develop water repellency?If so,does water repellency affect infiltration on a seasonal basis?For this,water repellency and infiltration were measured in a grid of 72points during a dry and a wet month of a tropical riparian forest with a shallow water table in a region with highly marked climatic seasonality.Water repellency and infiltration were significantly different between the wet and dry months.Water repellency affected negatively infiltration in the dry month,its effect in the wet month was insignificant.As a result,a higher infiltration capacity was observed over the wet period.Previous research has claimed that the development and persistence of repellency in soils could promote other hydrological processes such as overland flow.The findings shown here demonstrate that such phenomenon does not persist longer than the dry season.

Reduction of ice adhesion on nanostructured and nanoscale slippery surfaces

Ice nucleation and accretion on structural surfaces are sources of major safety and operational concerns in many industries including aviation and renewable energy.Common methods for tackling these are active ones such as heating,ultrasound,and chemicals or passive ones such as surface coatings.In this study,we explored the ice adhesion properties of slippery coated substrates by measuring the shear forces required to remove a glaze ice block on the coated substrates.Among the studied nanostructured and nanoscale surfaces[i.e.,a superhydrophobic coating,a fluoropolymer coating,and a polydimethylsiloxane(PDMS)chain coating],the slippery omniphobic covalently attached liquid(SOCAL)surface with its flexible polymer brushes and liquid-like structure significantly reduced the ice adhesion on both glass and silicon surfaces.Further studies of the SOCAL coating on roughened substrates also demonstrated its low ice adhesion.The reduction in ice adhesion is attributed to the flexible nature of the brush-like structures of PDMS chains,allowing ice to detach easily.

Liquid–liquid extraction of levulinic acid from aqueous solutions using hydrophobic tri-n-octylamine/alcohol-based deep eutectic solvent

Levulinic acid(LA)is one of the top-12 most promising biomass-based platform chemicals,which has a wide range of applications in a variety of fields.However,separation and purification of LA from aqueous solution or actual hydrolysate continues to be a challenge.Among various downstream separation technologies,liquid-liquid extraction is a low-cost,effective,and simple process to separate LA.The key breakthrough lies in the development of extractants with high extraction efficiency,good hydrophobicity,and low cost.In this work,three hydrophobic deep eutectic solvents(DESs)based on tri-n-octylamine(TOA)as hydrogen bond acceptor(HBA)and alcohols(butanol,2-octanol,and menthol)as hydrogen bond donors(HBDs)were developed to extract LA from aqueous solution.The molar ratios of HBD and HBA,extraction temperature,contact time,solution pH,and initial LA concentration,DES/water volume ratios were systematically investigated.Compared with 2-octanol-TOA and menthol-TOA DES,the butanol-TOA DES exhibited the superior extraction performance for LA,with a maximum extraction efficiency of 95.79±1.4%.Moreover,the solution pH had a great impact on the LA extraction efficiency of butanol-TOA(molar ratio=3:1).It is worth noting that the extraction equilibrium time was less than 0.5 h.More importantly,the butanol-TOA(3:1)DES possesses good extraction abilities for low,medium,and high concentrations of LA.

Physico-chemical parameters for the assembly of moxifloxacin hydrochloride and cetyltrimethylammonium chloride mixture in aqueous and alcoholic media

The aggregation behavior of the mixture of cetyltrimethylammonium chloride(CTAC), a cationic surfactant, and moxifloxacin hydrochloride(MFH), a fourth-generation fluoroquinolone antibiotic drug, has been studied using the conductivity technique in aqueous and alcoholic(EtOH, 1-PrOH, and 2-BuOH)media. The study was performed at several temperatures between 298.15 and 323.15 K at 5 K intervals.The assembly has been characterized by evaluating the micellar parameters, such as the critical micelle concentration(CMC) and the counter ion binding(β), of the CTAC + MFH mixture. The values of the CMC for the assembly of the CTAC + MFH mixture were reliant on the composition of alcohols in the mixed solvents and the temperature. The CMC values of the CTAC + MFH mixture increased with increasing temperature;that is, assembly was delayed by increased temperature. The micellization of the CTAC + MFH mixed system was delayed in alcoholic media. The observed-ΔG0mvalues for the association of the CTAC + MFH mixed system demonstrated a spontaneous aggregation process under all study conditions.Based on the-ΔH^(0)_(m) and +ΔS^(0)_(m) values, the association of the CTAC + MFH mixture is exothermic and the interaction forces acting between the CTAC and MFH species are hydrophobic, ion–dipole, and electrostatic interactions. The transfer properties and enthalpy–entropy compensation were also assessed and described comprehensively.

Efficient H_(2)O_(2)Electrosynthesis and Its Electro-Fenton Application for Refractory Organics Degradation

Hydrogen peroxide(H_(2)O_(2))in situ electrosynthesis by O_(2)reduction reaction is a promising alternative to the conventional Fenton treatment of refractory wastewater.However,O_(2)mass transfer limitation,cathodic catalyst selectivity,and electron transfer in O_(2)reduction remain major engineering obstacles.Here,we have proposed a systematic solution for efficient H_(2)O_(2)generation and its electro-Fenton(EF)application for refractory organic degradation based on the fabrication of a novel ZrO_(2)/CMK-3/PTFE cathode,in which polytetrafluoroethylene(PTFE)acted as a hydrophobic modifier to strengthen the O_(2)mass transfer,ZrO_(2)was adopted as a hydrophilic modifier to enhance the electron transfer of O_(2)reduction,and mesoporous carbon CMK-3 was utilized as a catalyst substrate to provide catalytic active sites.Moreover,feasible mass transfer of O_(2)from the hydrophobic to the hydrophilic layer was designed to increase the contact between O_(2)and the reaction interface.The H_(2)O_(2)yield of the ZrO_(2)/CMK-3/PTFE cathode was significantly improved by approximately 7.56 times compared to that of the co nventional gas diffusion cathode under the same conditions.The H_(2)O_(2)generation rate and Faraday efficiency reached125.98 mg·cm^(-2)·h^(-1)(normalized to 5674.04 mmol·g^(-1)·h^(-1)by catalyst loading)and 78.24%at-1.3 V versus standard hydrogen electrode(current density of-252 mA·cm^(-2)),respectively.The high H_(2)O_(2)yield ensured that sufficient OH was produced for excellent EF performance,resulting in a degradation efficiency of over 96%for refractory organics.This study offers a novel engineering solution for the efficient treatment of refractory wastewater using EF technology based on in situ high-yield H_(2)O_(2)electrosynthesis.

A critical review of self-diverting acid treatments applied to carbonate oil and gas reservoirs

Carbonate reservoirs generally achieved relatively low primary resource recovery rates.It is therefore often necessary to clean those reservoirs up and/or stimulate them post drilling and later in their production life.A common and basic carbonate reservoir cleanup technique to remove contaminating material from the wellbore is acidizing.The efficiency of acid treatments is determined by many factors,including:the type and quantity of the acid used;the number of repeated treatments performed,heterogeneity of the reservoir,water cut of the reservoir fluids,and presence of idle zones and interlayers.Post-treatment production performance of such reservoirs frequently does not meet design expectations.There is therefore much scope to improve acidizing technologies and treatment designs to make them more reliable and effective.This review considers acid treatment technologies applied to carbonate reservoirs at the laboratory scale and in field-scale applications.The range of acid treatment techniques commonly applied are compared.Differences between specific acid treatments,such as foamed acids,acid emulsions,gelled and thickened acid systems,targeted acid treatments,and acid hydraulic fracturing are described in terms of the positive and negative influences they have on carbonate oil production rates and recovery.Opportunities to improve acid treatment techniques are identified,particularly those involving the deployment of nanoparticles(NPs).Due consideration is also given to the potential environmental impacts associated with carbonate reservoir acid treatment.Recommendations are made regarding the future research required to overcome the remaining challenges pertaining to acid treatment applications.

Temperature-induced hydrophobicity transition of MXene membrane for directly preparing W/O emulsions

Although hydrophilic membranes are desired for reducing resistance to water permeation, hydrophilic surfaces are not used in the water-in-oil(W/O) membrane emulsification process because water spreads on the hydrophilic surface without forming droplets. Here, we report that a hydrophilic ceramic membrane can form a hydrophobic interface in diesel at a higher temperature;interestingly, the experiments show that the contact angle increases when the temperature rises. The hydrophilic membrane surface evolves into a hydrophobic interface, particularly near the boiling point of water, resulting in a water contact angle of 147.5° ± 1.2°. This work established a method for preparing W/O monodispersed emulsions by direct emulsification of hydrophilic ceramic membranes at a temperature close to the boiling point of water.Additionally, it made high flux of membrane emulsification of monodispersed W/O emulsions possible,which satisfied the industrial requirements of fluidized catalytic cracking in the petrochemical industry.

High drug loading hydrophobic cross-linked dextran microspheres as novel drug delivery systems for the treatment of osteoarthritis

Drug delivery via intra-articular(IA)injection has proved to be effective in osteoarthritis(OA)therapy,limited by the drug efficiency and short retention time of the drug delivery systems(DDSs).Herein,a series of modified cross-linked dextran(Sephadex,S0)was fabricated by respectively grafting with linear alkyl chains,branched alkyl chains or aromatic chain,and acted as DDSs after ibuprofen(Ibu)loading for OA therapy.This DDSs expressed sustained drug release,excellent anti-inflammatory and chondroprotective effects both in IL-1βinduced chondrocytes and OA joints.Specifically,the introduction of a longer hydrophobic chain,particularly an aromatic chain,distinctly improved the hydrophobicity of S0,increased Ibu loading efficiency,and further led to significantly improving OA therapeutic effects.Therefore,hydrophobic microspheres with greatly improved drug loading ratio and prolonged degradation rates show great potential to act as DDSs for OA therapy.