Discovery and characterization of a new hydrothermal field at 2°N on the slow-spreading Carlsberg Ridge

A new hydrothermal field(Tianshi)was discovered on the rift valley wall through plume anomaly surveys and geological work conducted in 2012 and 2018 between 2°35′N and 2°43′N of the slow-spreading Carlsberg Ridge(CR).Here,the results of two expeditions conducted to detect and characterize the new hydrothermal field are reported.Mineralogical and geochemical data,as well as 14 C ages of a sediment core collected near the field are presented to reveal the hydrothermal history.Results show that the Tianshi field is a basalt-hosted hydrothermal system.Geochemical data of the sediments collected near the field indicate a strong hydrothermal contribution,and hydrothermal Fe and Cu fluxes range from 30 to 155 mg/(cm^(2)·ka)and 0.59 to 11.49 mg/(cm^(2)·ka),respectively.Temporal variations in the fluxes of hydrothermal Fe indicate that there have been at least three amplified hydrothermal venting events(H 1,H 2,and H 3)in the Tianshi field over the last 35.2 ka,in 28.6-35.2 ka BP,22.0-27.6 ka BP,and 1.2-11.4 ka BP,respectively.Hydrothermal event H 2 was driven by an increased magmatic production associated with sea level fall during the Last Glacial Maximum,while event H 3 was promoted by tectonic activity associated with a rapid sea level rise.This study further verified the role of sea level change in modulating hydrothermal activity on mid-ocean ridges.

Episodic hydrothermal alteration on Middle Permian carbonate reservoirs and its geological significance in southwestern Sichuan Basin,SW China

To analyze the episodic alteration of Middle Permian carbonate reservoirs by complex hydrothermal fluid in southwestern Sichuan Basin,petrology,geochemistry,fluid inclusion and U-Pb dating researches are conducted.The fractures and vugs of Middle Permian Qixia–Maokou formations are filled with multi-stage medium-coarse saddle dolomites and associated hydrothermal minerals,which indicates that the early limestone/dolomite episodic alteration was caused by the large-scale,high-temperature,deep magnesium-rich brine along flowing channels such as basement faults or associated fractures under the tectonic compression and napping during the Indosinian.The time of magnesium-rich hydrothermal activity was from the Middle Triassic to the Late Triassic.The siliceous and calcite fillings were triggered by hydrothermal alteration in the Middle and Late Yanshanian Movement and Himalayan Movement.Hydrothermal dolomitization is controlled by fault,hydrothermal property,flowing channel and surrounding rock lithology,which occur as equilibrium effect of porosity and permeability.The thick massive grainstone/dolomites were mainly altered by modification such as hydrothermal dolomitization/recrystallization,brecciation and fracture-vugs filling.Early thin-medium packstones were mainly altered by dissolution and infilling of fracturing,bedding dolomitization,dissolution and associated mineral fillings.The dissolved vugs and fractures are the main reservoir space under hydrothermal conditions,and the connection of dissolved vugs and network fractures is favorable for forming high-quality dolomite reservoir.Hydrothermal dolomite reservoirs are developed within a range of 1 km near faults,with a thickness of 30–60 m.Hydrothermal dolomite reservoirs with local connected pore/vugs and fractures have exploration potential.

Hydrothermal hydrogenation/deoxygenation of palmitic acid to alkanes over Ni/activated carbon catalyst

To produce paraffin from hydrogenation/deoxygenation of palmitic acid,model compound of bio-oil obtained by hydrothermal liquefaction(HTL)of microalgae has been an attractive focus in recent years.In order to avoid energy-intensive separation process of water and bio-oil,it is of importance that deoxygenation upgrading of fatty acids under hydrothermal conditions similar to HTL process.Herein,it is the first time to explore the application of activated carbon(AC)-supported non-noble-metal catalysts,such as Ni,Co,and Mo,and so on,in the hydrothermal hydrogenation/deoxygenation of long-chain fatty acids,and the obtained Ni/AC-H(the Ni/AC was further H_(2)pre-reduced)is one of the best catalysts.In addition,it is found that the catalytic activity can be further improved by H_(2)pre-reduction of catalyst.Characterization results that are more low valences of nickel and oxygen vacancy can be obtained after H_(2)pre-reduction,thus significant promoting the deoxygenation especially the decarbonylation pathway of fatty acids.The total alkanes yield can reaches 95.9%at optimal conditions(280℃,360 min).This work confirmed that the low-priced AC-supported non-noble-metal catalysts have great potential compared with the noble-metal catalyst,in hydrothermal upgrading of bio-oil.

Multi-Component Resource Recycling from Waste Light-Emitting Diode Under Hydrothermal Condition:Plastic Package Degradation,Speciation of Nano-TiO_(2),and Environmental Impact Assessment

Light emitting diodes(LEDs)have accounted for most of the lighting market as the technology matures and costs continue to reduce.As a new type of e-waste,LED is a double-edged sword,as it contains not only precious and rare metals but also organic packaging materials.In previous studies,LED recycling focused on recovering precious and strategic metals while ignoring harmful substances such as organic packaging materials.Unlike crushing and other traditional methods,hydrothermal treatment can provide an environment-friendly process for decomposing packaging materials.This work developed a closed reaction vessel,where the degradation rate of plastic polyphthalamide(PPA)was close to 100%,with nano-TiO_(2)encapsulated in plastic PPA being efficiently recovered,while metals contained in LED were also recycled efficiently.Besides,the role of water in plastic PPA degradation that has been overlooked in current studies was explored and speculated in detail in this work.Environmental impact assessment revealed that the proposed recycling route for waste LED could significantly reduce the overall environmental impact compared to the currently published processes.Especially the developed method could reduce more than half the impact of global warming.Furthermore,this research provides a theoretical basis and a promising method for recycling other plastic-packaged e-waste devices,such as integrated circuits.

Hydrothermal treatment of pearl millet grains:Effects on nutritional composition,antinutrients and flour properties

Pearl millet(Pennisetum glaucum)is one of the major millets with high nutritional properties.This crop exhibits exceptional resilience to drought and high temperatures.However,the processing of pearl millet poses a significant challenge due to its high lipid content,enzyme activity,and presence of antinutrients.Consequently,it becomes imperative to enhance the quality and prolong the shelf life of pearl millet flour by employing suitable technologies.Hydrothermal treatment in the food industry has long been seen as promising due to its potential to reduce microbial load,inactivate enzymes,and improve nutrient retention.This study aims to investigate the effects of hydrothermal treatment on the quality characteristics of pearl millet.The independent variables of the study were soaking temperature(35,45,55℃),soaking time(2,3,4 h),and steaming time(5,10,15 min).Treatment conditions had a statistically significant effect on nutrient retention.Major antinutrients like tannins and phytates were reduced by 0.99% to 5.94% and 0.36% to 6.00%,respectively,after the treatment.Lipase activity decreased significantly up to 10% with the treatment conditions.The findings of this study could potentially encourage the use of pearl millet flour in the production of various food items and promote the application of hydrothermal treatment in the field of food processing.

Cross-upgrading of biomass hydrothermal carbonization and pyrolysis for high quality blast furnace injection fuel production:Physicochemical characteristics and gasification kinetics analysis

The paper proposes a biomass cross-upgrading process that combines hydrothermal carbonization and pyrolysis to produce high-quality blast furnace injection fuel.The results showed that after upgrading,the volatile content of biochar ranged from 16.19%to 45.35%,and the alkali metal content,ash content,and specific surface area were significantly reduced.The optimal route for biochar pro-duction is hydrothermal carbonization-pyrolysis(P-HC),resulting in biochar with a higher calorific value,C=C structure,and increased graphitization degree.The apparent activation energy(E)of the sample ranges from 199.1 to 324.8 kJ/mol,with P-HC having an E of 277.8 kJ/mol,lower than that of raw biomass,primary biochar,and anthracite.This makes P-HC more suitable for blast furnace injection fuel.Additionally,the paper proposes a path for P-HC injection in blast furnaces and calculates potential environmental benefits.P-HC of-fers the highest potential for carbon emission reduction,capable of reducing emissions by 96.04 kg/t when replacing 40wt%coal injec-tion.

Characterization of Hydroxyapatite Extracted from Crab Shell Using the Hydrothermal Method with Varying Holding Times

Hydroxyapatite(HA)is a bio ceramic commonly utilized in bone tissue engineering due to its bioactive and osteoconductive properties.Crab shells are usually disregarded as waste material despite their significant CaCO_(3) content,and have not been widely utilized in the synthesis of HA.This study aims to synthesize and analyze HA derived from crab shells using the hydrothermal method with different durations of holding time.This study utilized precipitated calcium carbonate(PCC)derived from crab shells.With a hydrothermal reactor set at 160℃ and varying holding times of 14(HA_14),16(HA_16),and 18(HA_18)h,a PCC and(NH4)2HPO4 mixture was used to synthesize HA.The synthesis results were analyzed using scanning electron microscopy(SEM),fourier transform infrared spectroscopy(FTIR),and X-ray diffraction(XRD)tests.This study has accomplished the synthesis of HA from crab shells.Nonetheless,the final product of synthesis still contained CaCO_(3) as an impurity.The prolonged hydrothermal holding time of 14 to 18 h resulted in a reduction of impurities while increasing the percentage of crystal weight and crystallite size of HA.Specimen CH_18 is the best-quality product generated in this study.This specimen produced HA with the highest percentage of crystal weight and crystallite size compared to the other specimens.Furthermore,specimen CH_18 exhibited the lowest concentration of impurities.The Ca/P ratio in this specimen was also the closest to 1.67.The Ca/P ratio,crystallite size,and crystal weight percentage of this specimen are 1.54,19.06 nm,and 99.1%,respectively.

In situ Hydrothermal Oxidation of Ternary FeCoNi Alloy Electrode for Overall Water Splitting

Exploring noble metal-free catalyst materials for high efficient electrochemical water splitting to produce hydrogen is strongly desired for renewable energy development.In this article,a novel bifunctional catalytic electrode of insitu-grown type for alkaline water splitting based on FeCoNi alloy substrate has been successfully prepared via a facile one-step hydrothermal oxidation route in an alkaline hydrogen peroxide medium.It shows that the matrix alloy with the atom ratio 4∶3∶3 of Fe∶Co∶Ni can obtain the best catalytic performance when hydrothermally treated at 180℃for 18 h in the solution containing 1.8 M hydrogen peroxide and 3.6 M sodium hydroxide.The as-prepared Fe_(0.4)Co_(0.3)Ni_(0.3)-1.8 electrode exhibits small overpotentials of only 184 and 175 mV at electrolysis current density of 10 mA cm^(-2)for alkaline OER and HER processes,respectively.The overall water splitting at electrolysis current density of 10 mA cm^(-2)can be stably delivered at a low cell voltage of 1.62 V.These characteristics including the large specific surface area,the high surface nickel content,the abundant catalyst species,the balanced distribution between bivalent and trivalent metal ions,and the strong binding of in-situ naturally growed catalytic layer to matrix are responsible for the prominent catalytic performance of the Fe_(0.4)Co_(0.3)Ni_(0.3)-1.8 electrode,which can act as a possible replacement for expensive noble metal-based materials.

Conditions for the enrichment of karst hydrothermal resources in Bohai Bay Basin

Drilling for karst hydrothermal resources in eastern China has posed challenges,including disparities between the temperature and yield of geothermal water.It is evident that relying solely on geothermal anomalies or indications of karst reservoirs is inadequate for the exploration of karst hydrothermal resources.This study seeks to elucidate the cause of geothermal sweet spots by analyzing the interplay between geothermal anomalies and karst reservoirs and the underlying geological conditions for karst hydrothermal enrichment.Key findings include:(1)the Bohai Bay Basin has been geologically favorable for the development of karst hydrothermal resources since the Mesozoic era;(2)the karst hydrothermal enrichment varies significantly between the basin’s margin and its interior.On the basin margin,the enrichment is largely driven by groundwater activity and faults,particularly where faults facilitate the upwelling of geothermal water.In contrast,within the basin’s interior,karst hydrothermal resources are predominantly influenced by buried hills and are especially enriched in areas facilitating the discharge of deep geothermal waters.

Towards a new avenue for rapid synthesis of electrocatalytic electrodes via laser-induced hydrothermal reaction for water splitting

Electrochemical production of hydrogen from water requires the development ofelectrocatalysts that are active,stable,and low-cost for water splitting.To address these challenges,researchers are increasingly exploring binder-free electrocatalytic integratedelectrodes (IEs) as an alternative to conventional powder-based electrode preparation methods,for the former is highly desirable to improve the catalytic activity and long-term stability for large-scale applications of electrocatalysts.Herein,we demonstrate a laser-inducedhydrothermal reaction (LIHR) technique to grow NiMoO4nanosheets on nickel foam,which is then calcined under H2/Ar mixed gases to prepare the IE IE-NiMo-LR.This electrode exhibits superior hydrogen evolution reaction performance,requiring overpotentials of 59,116 and143 mV to achieve current densities of 100,500 and 1000 mA·cm-2.During the 350 h chronopotentiometry test at current densities of 100 and 500 m A·cm-2,the overpotentialremains essentially unchanged.In addition,NiFe-layered double hydroxide grown on Ni foam is also fabricated with the same LIHR method and coupled with IE-NiMo-IR to achieve water splitting.This combination exhibits excellent durability under industrial current density.The energy consumption and production efficiency of the LIHR method are systematicallycompared with the conventional hydrothermal method.The LIHR method significantly improves the production rate by over 19 times,while consuming only 27.78%of the total energy required by conventional hydrothermal methods to achieve the same production.

A Comparison of Hydrothermal Aging, SO2 and Propene Poisoning Effects on NH3-SCR over Cu-ZSM-5 and Cu-SAPO-34 Catalysts

This study was aimed to investigate the effects of hydrothermal aging, propene and SO2 poisoning on the ammonia-selective catalytic reduction (NH3-SCR) performance of both Cu-SAPO-34 and Cu-ZSM-5. The catalytic activities of fresh, aged and poisoned samples were tested in ammonia-selective catalytic reduction (NH3-SCR) of NOx conditions. The XRD, TG and N2-desorption results showed that the structures of the Cu-SAPO-34 and Cu-ZSM-5 remained intact after 750˚C hydrothermally aged, SO2 and propene poisoned. After hydrothermal aging at 750˚C for 12 h, the NO reduction performance of Cu-ZSM-5 was significantly reduced at lower temperatures, while that of Cu-SAPO-34 was less affected. Moreover, Cu-SAPO-34 catalyst showed high NO conversion with SO2 or propene compared to Cu-ZSM-5. However, Cu-ZSM-5 showed a larger drop in catalytic activity with SO2 or propene compared to Cu-SAPO-34 catalyst. The H2-TPR results showed that Cu2 ions could be reduced to Cu and Cu0 for Cu-ZSM-5, while no significant transformation of copper species was observed for Cu-SAPO-34. Meanwhile, the UV-vis DRS results showed that CuO species were formed in Cu-ZSM-5, while little changes were observed for the Cu-SAPO-34. Cu-SAPO-34 showed high sulfur and hydrocarbon poison resistance compared to Cu-ZSM-5. In summary, Cu-SAPO-34 with small-pore zeolite showed higher hydrothermal stability and better hydrocarbon and sulfur poison resistant than Cu-ZSM-5 with medium-pore.

Breaking the temperature limit of hydrothermal carbonization of lignocellulosic biomass by decoupling temperature and pressure

Hydrothermal carbonization(HTC) of lignocellulosic biomass is a promising technology for the production of carbon materials with negative carbon emissions. However, the high reaction temperature and energy consumption have limited the development of HTC technology. In conventional batch reactors, the temperature and pressure are typically coupled at saturated states. In this study, a decoupled temperature and pressure hydrothermal(DTPH) reaction system was developed to decrease the temperature of the HTC reaction of lignocellulosic biomass(rice straw and poplar leaves). The properties of hydrochars were analyzed by scanning electron microscopy(SEM), Fourier transform infrared(FTIR) spectroscopy, X-ray photoelectron spectroscopy(XPS), Raman spectroscopy, X-ray diffraction(XRD), thermogravimetric analyzer(TGA), etc. to propose the reaction mechanism. The results showed that the HTC reaction of lignocellulosic biomass could be realized at a low temperature of 200℃ in the DTPH process, breaking the temperature limit(230℃) in the conventional process. The DTPH method could break the barrier of the crystalline structure of cellulose in the lignocellulosic biomass with high cellulose content, realizing the carbonization of cellulose and hemicellulose with the dehydration, unsaturated bond formation, and aromatization. The produced hydrochar had an appearance of carbon microspheres, with high calorific values, abundant oxygen-containing functional groups, a certain degree of graphitization, and good thermal stability. Cellulose acts not only as a barrier to protect itself and hemicellulose from decomposition, but also as a key precursor for the formation of carbon microspheres. This study shows a promising method for synthesizing carbon materials from lignocellulosic biomass with a carbon-negative effect.

Hydrothermal Systems Characterized by Crustal Thermally-dominated Structures of Southeastern China

Southeastern China(SE China)is located in the Pacific tectonic domain and has experienced a series of tectono-magmatic events induced by the subduction of the Paleo-Pacific Plate since the late Mesozoic.The subduction formed a series of NE-NNE oriented faults under a NW-SE regional stress field,along which a number of thermal springs occur.Previous studies have focused on the genesis mechanism of specific geothermal fields in SE China,but the general characteristics of hydrothermal systems in SE China remains unclear.In this study,we investigate the correlation between geothermal activity,hydrochemical type and regional faults by studying the distribution of hydrothermal activity and geochemical properties of typical hydrothermal systems in SE China.The hydrothermal systems in SE China have a crustal thermally-dominated structural origin unique to the specific geological and tectonic conditions of the Eurasian Plate margin.The upwelling of the asthenosphere and the widespread granitoids with high radiogenic heat production in SE China provide major heat sources for regional geothermal anomalies.The NE-oriented crustal thermally-dominated faults are critical for the formation of geothermal anomalies and NW-oriented extensional faults have created favorable conditions for meteoric water infiltration,transportation and the formation of thermal springs.

Developing super-hydrophobic and corrosion-resistant coating on magnesium-lithium alloy via one-step hydrothermal processing

Formation of super-hydrophobic and corrosion-resistant coatings can provide significant corrosion protection to magnesium alloys.However,it remains a grand challenge to produce such coatings for magnesium-lithium alloys due to their high chemical reactivity.Herein,a one-step hydrothermal processing was developed using a stearic-acid-based precursor medium,which enables the hydrothermal conversion and the formation of low surface energy materials concurrently to produce the super-hydrophobic and corrosion-resistant coating.The multiscale microstructures with nanoscale stacks and microscale spheres on the surface,as well as the through-thickness stearates,lead to the super-hydrophobicity and excellent corrosion resistance of the obtained coating.

A highly hydrothermal stable copper-based catalyst for catalytic wet air oxidation of m-cresol in coal chemical wastewater

Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.

High-precision double-spike Cd isotopic measurements of seawater by MC-ICP-MS and its application to seawater affected by hydrothermal vent fluids

Cadmium(Cd)isotopes in seawater have been proven as an important geochemical tool for tracing ocean Cd circulation in the modern ocean.In this study,we evaluated a new method to separate Cd(*60 ng)from seawater using Chelex resin(1.0 g)coupled with AG-MP-1M resin.The results show that the Chelex resin is suffi-cient to remove Cd from Na and Mg matrix with Cd recoveries at 98.3±3.5%(2SD,N=6);while AG-MP-1M resin could separate Cd from the residual Na,Mg,and isobaric inferences.The total Cd recoveries of the method are 96.3±1.5%(2SD;N=4)and the salinity of the samples has no significant impacts on Cd recovery.Cd isotope ratios were measured using a Nu PlasmaⅢMC-ICP-MS and^(111)Cd–^(110)Cd double spike technique.By comparing theδ^(114/110)Cd values(0.00±0.06%)of synthetic seawaters doped with Cd isotope standard(NIST-3108;treated by Chelex+AG-MP-1M resin)and the reference value(-0.00%),no variations were observed.We also analyzed the Cd isotope compositions of three deep seawaters from a column at the Southwest Indian Ocean Ridges(SWIR).Theδ^(114/110)Cd values of the col-umn are decreased from 1.05±0.05%at 3200 m to 0.36±0.05%at 2800 m,differing from reportedδ^(114/110)Cd values of deep seawater in other oceans.Considering the spatial distance between the column and active hydrothermal vents in SWIR(-13 km),we propose that such positiveδ^(114/110)Cd values of deep seawater were likely contaminated by vent fluids,which could provide heavy Cd isotope to deep seawaters.This study demon-strates that Cd isotope is more sufficient to distinguish the impact of plumes on deep seawater.

Hydrochar Pelletization towards Solid Biofuel from Biowaste Hydrothermal Carbonization

Hydrothermal carbonization is highly applicable to high moisture biomass upgrading due to the fact that moist-ure involved can be directly used as reaction media under the subcritical-water region.With this,value-added utilization of hydrochar as solid fuel with high carbon and energy density is one of the important pathways for biomass conversion.In this review,the dewatering properties of hydrochar after the hydrothermal carbonization of biowaste,coalification degree with elemental composition and evolution,pelletization of hydrochar to enhance the mechanical properties and density,coupled with the combustion properties of hydrochar biofuel were discussed with various biomass and carbonization parameters.Potential applications for the co-combustion with coal,cleaner properties and energy balance for biowaste hydrothermal carbonization were presented as well as the challenges.

Effect of solvents on the morphology and structure of barium titanate synthesized by a one-step hydrothermal method

Tetragonal barium titanate was synthesized from barium hydroxide octahydrate and titanium tetrachloride through a simple one-step hydrothermal method.The effect of different solvents on the crystal structure and morphology of barium titanate nanoparticles during the hy-drothermal process was investigated.Except for ethylene glycol/water solvent,impurity-free barium titanate was synthesized in pure water,methanol/water,ethanol/water,and isopropyl alcohol/water mixed solvents.Compared with other alcohols,ethanol promotes the formation of a tetragonal structure.In addition,characterization studies confirm that particles synthesized in methanol/water,ethanol/water,and isopropyl al-cohol/water mixed solvents are smaller in size than those synthesized in pure water.In the case of alcohol-containing solvents,the particle size decreases in the order of isopropanol,ethanol,and methanol.Among all the media used in this study,ethanol/water is considered the optimum reaction media for barium titanate with high tetragonality(defined as the ratio of two lattice parameters c and a,c/a=1.0088)and small aver-age particle size(82 nm),which indicates its great application potential in multilayer ceramic capacitors.

Mineralogy and geochemistry of hydrothermal sulphide from a submarine volcanic high at 18°36.4'S Central Lau Spreading Center, Southwest Pacific

We report the mineralogy and geochemistry of hydrothermal sulphide from the crater of a volcanic high near 18°36.4′S of the Central Lau Spreading Center.During 1990s,that volcanic structure was reported active and sulphide samples were collected by MIR submersible.A section of a chimney-like structure from the crater-floor was studied here.The Fe-depleted sphalerites,and Co-depleted pyrites in that chimney were similar to those commonly found in low to moderate temperature(<300℃)sulphides from sediment-starved hydrothermal systems.Bulk analyses of three parts of that chimney section showed substantial enrichment of Zn(18%–20%)and Fe(14%–27%)but depletion of Cu(0.8%–1.3%).In chondrite-normalized rare earth element-patterns,the significant negative Ce-anomalies(Ce/Ce*=0.27–0.39)and weakly positive Eu-anomalies(Eu/Eu*=1.60–1.68)suggested sulphide mineralisation took place from reduced low-temperature fluid.The depleted concentration of lithophiles in this sulphide indicates restricted contribution of sub-ducting plate in genesis of source fluid as compared to those from other parts of Lau Spreading Centre.Uniform mineralogy and bulk composition of subsamples across the chimney section suggests barely any alteration of fluid composition and/or mode of mineralisation occurred during its growth.

One-step hydrothermal synthesis of 2,5-PDCA-containing MgAl-LDHs three-layer composite coating with high corrosion resistance on AZ31

The addition of 2,5-pyridinedicarboxylic acid(2,5-PDCA)to the Mg-Al LDH coating,which was prepared by one-step hydrothermal synthesis,had extremely enhanced the corrosion protection of AZ31 Mg alloy,although the 2,5-PDCA could not be intercalated into the interlayer spacing.The corrosion current density of 0.05 mol L^(−1)2,5-PDCA LDH containing LDH coating is 3.18 nA cm^(−2),reduced by two orders of magnitude compared to the LDH coating without inhibitor,and the corrosion inhibition efficiency of the coating is 98.05%.The coating formed on the surface of AZ31 was peeled off from the substrate by using a mechanical method and SEM observation of the cross-section showed that the coating consisted of three different layers.The innermost layer is a thick layer that consists of Mg(OH)_(2)and the intermediate layer is LDH,which is vertical to the substrate and the outmost layer is a thin but very dense deposit layer of LDH agglomerates with complexes of 2,5-PDCA and Mg.This kind of sediment/LDH/Mg(OH)_(2)three-layer composite structure was accountable for the increase in the corrosion resistance of AZ31 Mg alloy.