Modeling Hydrothermal Transfer Processes in Permafrost Regions of Qinghai-Tibet Plateau in China

Hydrothermal processes are key components in permafrost dynamics; these processes are integral to global wanning. In this study the coupled heat and mass transfer model for （CoupModel） the soil-plant-atmosphere-system is applied in high-altitude permafrost regions and to model hydrothermal transfer processes in freeze-thaw cycles. Measured meteorological forcing and soil and vegetation properties are used in the CoupModel for the period from January 1, 2009 to December 31, 2012 at the Tanggula observation site in the Qinghai-Tibet Plateau. A 24-h time step is used in the model simulation. The results show that the simulated soil temperature and water content, as well as the frozen depth compare well with the measured data. The coefficient of determination （R2） is 0.97 for the mean soil temperature and 0.73 for the mean soil water content, respectively. The simulated soil heat flux at a depth of 0-20 cm is also consistent with the monitored data. An analysis is performed on the simulated hydrothermal transfer processes from the deep soil layer to the upper one during the freezing and thawing period. At the beginning of the freezing period, the water in the deep soil layer moves upward to the freezing front and releases heat during the freezing process. When the soil layer is completely frozen, there are no vertical water ex- changes between the soil layers, and the heat exchange process is controlled by the vertical soil temperature gradient. During the thaw- ing period, the downward heat process becomes more active due to increased incoming shortwave radiation at the ground surface. The melt water is quickly dissolved in the soil, and the soil water movement only changes in the shallow soil layer. Subsequently, the model was used to provide an evaluation of the potential response of the active layer to different scenarios of initial water content and climate warming at the Tanggula site. The results reveal that the soil water content and the organic layer provide protection against active layer deepening in summer, so climate warming will cause the permafrost active layer to become deeoer and permafrost degradation.

Mineral Components, Texture, and Forming Conditions of Hydrothermal Chimney on the East Pacific Rise at 9°-10°N

To characterize the hydrothermal processes of East Pacific rise at 9°-10°N, sulfide mineral compositions, textural, and geochemical features of chimney ores were studied using ore microscope,scanning electron microscope, X-ray diffraction analysis, and electron microprobe techniques. Results show that there are three mineral assemblages for the hydrothermal chimney ores, namely：（i） anhydrite ＋ marcasite ＋ pyrite, （ii） pyrite ＋ sphalerite ＋ chalcopyrite, and （iii） chalcopyrite ＋ bornite ＋ digenite ＋ covellite. Mineral assemblages, zonational features, and geochemical characteristics of the ore minerals indicate that ore fluid temperature changed from low to high then to low with a maximum temperature up to 400 ℃. The chimney is a typical black smoker. The initial structure of the chimney was formed by the precipitation of anhydrites, and later the sulfides began to precipitate in the inner wall.

Impact of hydrothermal process on the nutrient ingredients of restaurant garbage

In order to recover the nutrient resource from restaurant garbage, a complete trial with 2 factors on 5 levels of experiments was carried out. The temperature and heating time are the main factors influencing on hydrothermal process （HP） by which improves the degradability and digestibility of the restaurant garbage favorably to make animal feeds or fertilizer. The results showed the variation of protein, saccharide, and oil in the garbage. It showed that protein dissolved and liquefied during hydrothermal process, which made organic nitrogen in solid phase transfer to liquid phase. After heating at 180℃ for 60min, organic nitrogen in liquid phase began to transform into ammonia. It also showed that hydrothermal process could promote the dextrinization, dissolution of the starch and its hydrolysis to reducing sugar, due to that starch in the restaurant garbage decreases and reducing sugar increases. When the temperature reached 140℃, the reducing sugar started to decrease due to chemical reactions. The cellulose was stable at 100-180℃. The floatable oil increased markedly in the hydrothermal process. The suitable condition for de-oil was observed at 160℃ heating for 80 min. Furthermore, the extraction of grease from the solid phase accords with first-order reaction dynamic model.

In-situ experiment investigations of hydrothermal process of highway in deep seasonal frozen soil regions of Inner Mongolia, China

To reveal the influencing factors and changing rules for the hydrothermal interaction process of highway subgrade, the field measurements of Shiwei-Labudalin Highway in Inner Mongolia, China was conducted for 3 years, based on which the freezing-thawing rules and water content changing characteristics were analyzed. The main results show the subgrade presents a frequent freezing-thawing alternation, and the water content of subgrade exhibits an obvious seasonal alternation. The subbase has the maximum water content, while the base has the minimum water content. The change of water flux is concentrated in the thawing period and consistent with the change of temperature gradient. The subbase layer has the most active water flux due to the heat absorption and impermeability of pavement that easily causes the water accumulation in this layer. Therefore, the prevention and treatment for the freezing-thawing disease should be started from heat insulation and water resistance.

Developing super-hydrophobic and corrosion-resistant coating on magnesium-lithium alloy via one-step hydrothermal processing

Formation of super-hydrophobic and corrosion-resistant coatings can provide significant corrosion protection to magnesium alloys.However,it remains a grand challenge to produce such coatings for magnesium-lithium alloys due to their high chemical reactivity.Herein,a one-step hydrothermal processing was developed using a stearic-acid-based precursor medium,which enables the hydrothermal conversion and the formation of low surface energy materials concurrently to produce the super-hydrophobic and corrosion-resistant coating.The multiscale microstructures with nanoscale stacks and microscale spheres on the surface,as well as the through-thickness stearates,lead to the super-hydrophobicity and excellent corrosion resistance of the obtained coating.

Resistive Switching Memory of TiO2 Nanowire Networks Grown on Ti Foil by a Single Hydrothermal Method

The resistive switching characteristics of TiO_2 nanowire networks directly grown on Ti foil by a single-step hydrothermal technique are discussed in this paper. The Ti foil serves as the supply of Ti atoms for growth of the TiO_2 nanowires, making the preparation straightforward. It also acts as a bottom electrode for the device. A top Al electrode was fabricated by e-beam evaporation process. The Al/TiO_2 nanowire networks/Ti device fabricated in this way displayed a highly repeatable and electroforming-free bipolar resistive behavior with retention for more than 10~4 s and an OFF/ON ratio of approximately 70. The switching mechanism of this Al/TiO_2 nanowire networks/Ti device is suggested to arise from the migration of oxygen vacancies under applied electric field. This provides a facile way to obtain metal oxide nanowire-based Re RAM device in the future.

Lincang Superlarge Germanium Deposit in Yunnan Province,China: Sedimentation,Diagenesis,Hydrothermal Process and Mineralization

The mineralization is related closely to sedimentation, diagenesis and hydrothermal processes. In this paper, investigations are carried out on coal occurrence, maceral composition, inorganic minerals, trace elements and huminite reflectance. It is concluded that the source of Lincang superlarge deposit is mainly the muscovite granite in the west edge of the basin. During sedimentation, Ge (germanium) was leached out and entered the basin. Ge was adsorbed by lower organism and humic substances in water. Lincang lignite underwent three thermal processes: peatification, early diagenesis and hydrothermal transformation. During peatification, Ge was adsorbed or complexed by humic colloids. During early diagenesis, the Ge associated with humic acids was hard to mobilize or transport. Most of Ge entered the structure of huminite while a small amount of Ge was associated with residual humic acids as complex or humate. During hydrothermal transformation, the heated natural water or deep fluid from basement encountered the coal layer within tectonic weak zone. SO 2- 4 was reduced by coal organic matter. Pyrite and calcite formed. Hydrothermal process did not contribute significantly to mineralization.

Hexagonal hematite platelets synthesized from pyrite cinders by hydrothermal process

Well-crystallized hexagonal hematite （α-Fe2O3） platelets were synthesized by hydrothermal process, using a highly concentrated ferric hydroxide as precursor. The precursor was prepared by adding ammonia to the ferric sulfate solution which was obtained by leaching pyrite cinders with sulfuric acid. Structure and morphology of the synthesized products were investigated by X-ray diffraction, scanning electron microscope, transmission electron microscope and selected area electron diffraction. The results reveal that the reaction temperature has significant effects on the structure, size and shape of the synthesized hematite particles. Typical hexagonal hematite platelets, about 0.4-0.6 μm in diameter and 0.1 μm in thickness, were prepared at 230 ℃ for 0.5 h. Al^3＋, contained in the sulfuric acid leaching solution as an impurity, plays an extremely important role in the formation of hexagonal hematite. In addition, a possible mechanism about the formation of hexagonal hematite platelets was proposed.

Hydrothermal synthesis and dielectric properties of chrysanthemum-like ZnO particles

By orthogonal design theory, technological parameters of chrysanthemum-like ZnO particles prepared in a hydrothermal process are optimized. This paper reports a set of technological parameters for growing chrysanthemumlike ZnO particles on a large scale. It investigates the morphologies and crystalline structures of the as-synthesized three-dimensional ZnO particles with a scanning electron microscope, x-ray diffractometer and transmission electron microscope, and the possible growth mechanism on the three-dimensional ZnO particles. The experimental results indicate that the values of ε′ε″ and tan δe gradually increase in the X band with the improvement of the developmental level of chrysanthemum-like ZnO particles, implying that the electromagnetic wave absorbing property depends on the morphologies of three-dimensional ZnO particles.

A novel hydrothermal method for zinc extraction and separation from zinc ferrite and electric arc furnace dust

A novel hydrothermal process was developed to extract zinc from pure zinc ferrite（ZnFe2O4） nanopowder and zinc-containing electric arc furnace（EAF） dust using hexahydrated ferric chloride（FeCl3-6H2O） as a decomposing agent.The effects of solid FeCl3-6H2O to ZnFe2O4 ratio by mass（RF/Z）,hydrothermal reaction temperature,and time on zinc extraction were systematically investigated.In the results,when the hydrothermal reaction is conducted at 150℃ for 2 h with RF/Z of 15：20,the efficiency of zinc extraction from ZnFe2O4 reaches97.2%,and the concentration of ferric ions（Fe^3＋） in the leaching solution is nearly zero,indicating a high selectivity for zinc.In addition,the zinc extraction efficiency from the EAF dust reaches 94.5%in the case of the hydrothermal reaction performed at 200℃ for 10 h with the solid FeCl3-6H2O to EAF dust ratio by mass（RF/EAF dust） of 15：10.Zinc and iron separation is achieved by adjusting the pH value of the leaching solution according to the different precipitation pH values of metal hydroxides.

Dechlorination Behavior of Mixed Plastic Waste by Employing Hydrothermal Process and Limestone Additive

The usage of plastic-impregnated waste derived solid fuel in conventional combustor is hindered by many technical factors, especially its organic chlorine content. In this paper, experimental study of hydrothermal treatment on mixed plastic waste using the mixture of polypropylene, polystyrene, polyethylene and polyvinyl chloride （PVC） has been performed to observe the dechlorination effect of hydrothermal treatment on the waste. The system was generally applying saturated steam at around 2.4 MPa in a stirring reactor for about 90 minutes. After undergoing the process, the organic chlorine in treated plastic waste was reduced to 1,700 ppm level while the inorganic chlorine content was increased, suggesting an organic chlorine conversion phenomenon to inorganic chlorine, accompanied with low pH due to dehydrochlorination process. Additional limestone （Ca（OH）2） in subsequent experiment showed that the similar phenomenon was occurred but with higher pH and lower chlorine content in the condensed water, suggesting the production of inorganic salt rather than hydrochloric acid. Laboratory scale experiment was also performed to confirm the dechlorination phenomena especially for PVC, and the result showed that the main parameter which affected the dechlorination phenomena was the amount of water in hydrothermal process rather than limestone addition. It is suggested that a combination ofhydrothermal process and alkali addition would produce a low-chlorine solid product from plastic waste, promoting its usage as alternative solid fuel.

Gas separation using sol–gel derived microporous zirconia membranes with high hydrothermal stability

A microporous zirconia membrane with hydrogen permeance about 5 × 10-8mol·m-2·s-1·Pa-1, H2/CO2 permselectivity of ca. 14, and excellent hydrothermal stability under steam pressure of 100 k Pa was fabricated via polymeric sol–gel process. The effect of calcination temperature on single gas permeance of sol–gel derived zirconia membranes was investigated. Zirconia membranes calcined at 350 °C and 400 °C showed similar single gas permeance, with permselectivities of hydrogen towards other gases, such as oxygen, nitrogen, methane, and sulfur hexa fluoride, around Knudsen values. A much lower CO2permeance（3.7 × 10-9mol·m-2·s-1·Pa-1）was observed due to the interaction between CO2 molecules and pore wall of membrane. Higher calcination temperature, 500 °C, led to the formation of mesoporous structure and, hence, the membrane lost its molecular sieving property towards hydrogen and carbon dioxide. The stability of zirconia membrane in the presence of hot steam was also investigated. Exposed to 100 k Pa steam for 400 h, the membrane performance kept unchanged in comparison with freshly prepared one, with hydrogen and carbon dioxide permeances of 4.7 × 10-8and ~ 3 × 10-9mol·m-2·s-1·Pa-1, respectively. Both H2 and CO2permeances of the zirconia membrane decreased with exposure time to 100 k Pa steam. With a total exposure time of 1250 h, the membrane presented hydrogen permeance of 2.4 × 10-8mol·m-2·s-1·Pa-1and H2/CO2 permselectivity of 28, indicating that the membrane retains its microporous structure.

Comparison of Water-soluble CdSe Quantum Dots Made from Hydrothermal and Traditional Routes

The comparison of traditional route to the simple synthesis of CdSe semiconductor nanocrystals, with the hydrothermal route, where the reaction temperature can be reached at 220℃, was presented in this paper. The optical properties of the water-soluble CdSe quantum dots from the hydrothermal and traditional were characterized by UV-vis absorption spectra, photoluminescence （PL） spectra and HRTEM techniques. The HRTEM results show that with the increase of the reaction temperature, the naocrystal defects decreased. The UV-vis absorption peak moved to long wave-length with the increase of reaction temperature. The photoluminescence （PL） spectra show that the wavelength of the bright point, the PL quantum yield （QY） increased when the nanocrystal defects decreased. The optical property data confirm that hydrothermal router is a preferable method to traditional route for preparing water-soluble CdSe quantum dots.

Gas Sensing Properties of ZnO Tetrapod-Like Whiskers Prepared by Hydrothermal Process

ZnO tetrapod-like whiskers were prepared through a hydrothermal process using zinc powder as raw material.Its microstructure and morphology were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD results showed that the crystal structure of as-obtained sample can be indexed to hexagonal wurtzite ZnO.TEM results revealed that the ZnO sample took on tetrapod-like whisker shape.The gas sensors were prepared with the traditional sintering process and their gas sensitivities were detected.The test results of gas sensitivity showed that the sensors based on ZnO tetrapod-like whiskers are very sensitive to dilute ethanol vapor and H_2S.The relatively high sensitivity and selectivity of these sensors made from ZnO tetrapod-like whiskers demonstrated the potential for developing a new class of selective ethanol sensors.

Novel synthesis of cerium oxide nano photocatalyst by a hydrothermal method

Crystalline cubic cerium oxide nano particles have been synthesized from cerium(Ⅲ)nitrate(Ce(NO_(3))_(3).6H2_(O))and sodium hydroxide by a hydrothermal method.The effect of three different molar ratios of the NaOH precipitating agent on structural,optical,and photo catalytic activity was investigated.The synthesized cerium oxide nano particles were characterized by X-ray diffraction(XRD),a UV-vis spectrometer,scanning electron microscope(SEM),energy-dispersive X-ray spectroscopy(EDAX),Raman spectroscopy and X-ray photo electron spectroscopy(XPS).According to the findings,hydrothermally synthesized cerium oxide NPs have a high efficiency for photocatalytic degradation of methylene blue when exposed to UV light.Environmental water pollution is the major issue of the atmosphere.To get fresh water,humans could search the resources to purify the water in simple way and degradation is the one of the methods to purify salt water.

Hydrothermal Synthesis and Structure Analysis of Indium Vanadate (InVO_4)

In this article, hydrothermal process is applied to synthesize nanometer InVO4. Influences of different experimental conditions （including mixing ratio of raw materials, reaction temperature, reaction time and so on） upon the synthetic products＇ purity and crystallite size are discussed to determine the best synthetic condition. The structure of nanometer InVO4 is analyzed, which helps to further understand the structure characteristics of InVO4 synthesized by applying hydrothermal process and lays foundation for further research.

Rare-Element Pegmatites Rocks Rich and Li of the Aïr Massif of the Tchirozerine: Mineralogy and Chemical Composition Agadez Region-Northem Niger

The lithium potential in the Aïr massif is represented by mineral index of spodumene pegmatites and, lepidolite pegmatites. The mineral deposits of lithium occur in cluster or veins that cut the host rock or are located near the contact between the greenstone belt and granitic massif. The evidence of lithium is in the form of clusters or disseminated and stockwerk. Mineralogical characteristics show similarities between the Air Massif pegmatites and indicate the same homogenous source during the magma-generation process. The pegmatite rocks attracted the attention due to their wide exposure and composition, well appearance, and economically hosting of significant rare earth metals such as Sn and W. The mineralogical and petrographical investigations on the eight pegmatites rocks samples observed have a relative similarity, while a little difference in the shapes attributed to the ratio in the pegmatite rocks of the minerals. The occurrence of the kink band indicates the influence of the tectonic processes which affected the Aïr massif after the emplacement of late magmatic or post-magmatic pegmatites by injection into fractured rocks in the upper part of the crust. The Air Massif pegmatite has higher concentrations Li and of all trace elements except Hf and occasionally Zr, Ti, Sn and Mg of for the economic exploration.

Growth mechanism and photocatalytic evaluation of flower-like ZnO microstructures prepared with SDBS assistance

Flower-like ZnO microstructures were successfully produced using a hydrothermal method employing ZnSO_(4)/(NH_(4))_(2)SO_(4) as a raw material.The effect of the operating parameters of the hydrothermal temperature, OH^(-)/Zn^(2+) molar ratio, time, and amount of dispersant on the phase structure and micromorphology of the ZnO particles were investigated.The synthesis conditions of the flower-like ZnO microstructures were: hydrothermal temperature of 160℃, OH^(-)/Zn^(2+) molar ratio of 5:1, reaction time of 4 h, and 4 mL of dispersant.The flower-like ZnO microstructures were comprised of hexagon-shaped ZnO rods arranged in a radiatively.Degradation experiments of Rhodamine B with the flower-like ZnO microstructures demonstrated a degradation efficiency of 97.6% after 4 h of exposure to sunshine, indicating excellent photocatalytic capacity.The growth mechanism of the flower-like ZnO microstructures was presented.

Gasoline Sensor Based on Flower-Like ZnO

<正>Flower-like ZnO was prepared through a hydrothermal process using zinc sulfate as raw material.The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM).XRD results showed that the as-obtained sample could be indexed to hexagonal wurtzite ZnO.TEM results revealed that the ZnO sample presented flower-like shape.The gas sensors were prepared with the traditional sintering process and their gas sensitivities were detected.The gas sensitivity results showed that the sensors based on flower-like ZnO were very sensitive to dilute 90~# gasoline.The relatively high sensitivity and selectivity of these sensors made from flower-like ZnO demonstrated the potential for developing a new class of selective gasoline sensors.

Single-step Preparation of Nano-homogeneous NiO/YSZ Composite Anode for Solid Oxide Fuel Cells

Homogeneous co-precipitation and hydrothermal treatment were used to prepare nano- and highly dispersed Ni O/YSZ(yttria-stabilized zirconia) composite powders. Composite powders of size less than 100 nm were successfully prepared. This process did not require separate sintering of the YSZ and Ni O to be used as the raw materials for solid oxide fuel cells. The performance of a cell fabricated using the new powders(max.power density ~0.87 W/cm^2) was higher than that of a cell fabricated using conventional powders(max. power density ~0.73 W/cm^2). Co-precipitation and hydrothermal treatment proved to be very effective processes for reducing cell production costs as well as improving cell performance.