Effect of slow shot speed on externally solidified crystal,porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy

The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).

Effect of a High Magnetic Field on the Microstructure During Directionally Solidified Sn-20wt.%Pb Hypoeutectic Alloy

The microstructures of Sn-20wt.%Pb hypoeutectic alloy directionally solidified under a longitudinal magnetic field were investigated.The results show that the application of a high magnetic field has a great influence on the morphology of primary β-Sn phase at a temperature gradient of G_L=52 K/cm.At a certain growth speed,with the increase of magnetic field intensity,the magnetic field causes the primary β-Sn phase irregular and to be deformed,further,the magnetic field promotes the columnar to equaixed transition(CET).Further,the thermoelectric magnetic force(TEMF) imposed on the dendrite under a high magnetic field has been calculated and the results show that the numerical magnitude of the TEMF during directional solidification under a 10 T high magnetic field is about 10~4N/m^3 and this force should be responsible for the occurrence of the CET in the Sn-Pb alloy.This may act as an experimental proof that the coupling of temperature gradient and high magnetic field will induce the occurrence of the CET in Sn-Pb alloy.Above phenomena may be attributed to the thermoelectric magnetic force(TEMF)in solid.

Research on semi-solid slurry of a hypoeutectic Al-Si alloy prepared by low superheat pouring and weak electromagnetic stirring

The semi-solid slurry of a hypoeutectic Al-Si alloy was manufactured by low superheat pouring and weak electromagnetic stirring. The effects of pouting temperature and stirring power on the semi-solid slurry were investigated. The results indicated that the semi-solid slurry to satisfy rheocasting can be manufactured by low superheat pouring and weak electromagnetic stirring. The pouring temperature （or superheat） and the stirring power remarkably affected the morphology of primary α-Al and the size of primary α-Al, and there is no obvious effect of stirring time on primary α-Al. Compared with the samples made by low superheat pouring with no stirring, the nucleation rate, particle morphology and grain size of primary α-Al in A356 were markedly improved by low superheat pouring and weak electromagnetic stirring. On the condition of weak electromagnetic stirring, the pouring temperature with low superheat can be suitably raised to reach the effectiveness obtained from the lower pouring temperature without stirring.

Refining Effect of Boron on Hypoeutectic Al-Si Alloys

Several concepts of the grain refinement mechanism of B on hypoeutectic Al-Si alloys have been adopted: the refining effect of B on the a-AI and eutectic Si with the different additions of Al-B master alloys made at 850℃ was investigated; and the Al-B master alloys formed under different temperature conditions have been studied to explore the morphologies of AIB2 particles; slowly cooled sample with addition of Al-B was made to explore the refinement mechanism. AI-B master alloy can refine not only a-AI, but eutectic Si. Theoretical analysis indicates that, although AIB2 does not take part directly in the nucleation process in pure Al in the presence of Si, it provides a substrate for precipitation of a small content of Si from which a-At will grow without any undercooling. When the temperature decreases to eutectic line, AIB2 subsequently nucleates eutectic Si; AIB2 particles appear in two different morphologies, namely, hexagonal platelet and tetradehedron morphology which depend on the processing temperature conditions.

Effects of Si Content and the Addition Amount of Al-3B Master Alloy on the Solidification Structures of Hypoeutectic Al-Si Alloys

Effects of Si content and the addition amount of Al-3B master alloy on the solidification structures of hypoeutectic Al-Si alloys were studied. The addition amounts of the master alloy were 0.2%, 0.4%, 0.7% and 1% (mass fraction, so as the follows), respectively. The Si content of Al-Si binary alloys investigated varied from 1% to 11%. The observation of macrostructures of non-refined samples showed that 3% Si constitutes a transition point at which the minimum grain size can be obtained. It was also found that Al-3B master alloy can shift the transition point towards a higher Si value when its addition amount increases, making this point appear at 4%, 5% and 6% Si as its addition amount increases up to 0.4%, 0.7% and 1%, respectively.

Microstructure and rheological properties of a semisolid A356 alloy with erbium addition

The effects of erbium addition on the rheological properties and microstructure of a semisolid A356 alloy were studied.The semisolid slurries were prepared through the serpentine channel technique before they were thixoformed using parallel-plate compre ssion with cylindrical discs.The grain and globule size decreases as the Er content increases,resulting in an improved and uniform distribution of spherical primaryα-Al phase within the semisolid slurry.The addition of the Er modifies the grain morphology and size of theα-Al grains,resulting in a better and more uniform distribution of spherical primaryα-AI phase within the semisolid slurry.As a result,rheocast quality index increases with the addition of Er,which is suitable for the thixoforming process.The A356 alloy without Er has the highest viscosity herein.The viscosity decreases,and the flow characteristics of the semisolid feedstock are expected to improve when Er is added as a result of the refinement of primary a-Al and modification of eutectic silicon.Furthermore,the refined semisolid A356 alloys with Er show a slightly larger fraction of highangle grain boundaries compared to that for the unrefined alloy.