In this study, in order to investigate the influence of Cr element on the impact fracture process of ductile Ni-resistant alloyed iron at low temperature, different contents of Cr element were added to ductile Ni-resi...In this study, in order to investigate the influence of Cr element on the impact fracture process of ductile Ni-resistant alloyed iron at low temperature, different contents of Cr element were added to ductile Ni-resistant(DNR) austenitic alloyed iron. The experimental results show that Cr addition can increase the hardness of the DNR alloyed iron, but it has an destructive effect on low-temperature impact properties. Through the analysis of the dynamic load and absorbed energy of samples with different Cr contents in the impact fracture process, and the comparison of the impact fracture process at room and low temperatures, it reveals that Cr addition into the DNR alloyed iron can facilitate the formation of the carbide mixture in Mn23C6 and Cr23C6 with homogeneous and discontinuous distribution. Meanwhile, Cr addition also can improve the the maximum dynamic load and crack initiation energy at low temperature, but has no obvious effect on the yield behavior of the DNR alloyed iron in the impact fracture process. Compared with the impact crack propagation process at room temperature, the metastable propagation energy at low temperature declines significantly with an increase in Cr content. This is because the micro-cracks that caused by the carbides weaken the matrix, resulting in the decline of impact crack propagation resistance. The fracture analysis results also show that the impact fracture mechanism gradually transforms from ductile to brittle with an increase in Cr content at low temperature. It explains that too much Cr addition can lead to brittle fracture even though the austenitic matrix has a good toughness at low temperature.展开更多
A method was presented to prepare aluminide coatings on metals by combining the pack aluminizing with the ball impact process. This technique applied mechanical vibration to a retort, which was loaded with pack-alumin...A method was presented to prepare aluminide coatings on metals by combining the pack aluminizing with the ball impact process. This technique applied mechanical vibration to a retort, which was loaded with pack-aluminizing powder, specimens and alloy balls. Pack aluminizing was carried out with repeated ball impact, which accelerated chemical reactions and atomic diffusion. Aluminide coatings were formed at a relatively lower temperature (below 600 ℃) and in a shorter treatment time, compared with the conventional pack aluminizing. The effects of the operation temperature and the treatment time on the formation of the coatings were analysed. The SEM, EDS and XRD analysis results show that the aluminide coatings appear to be homogeneous, with a high density and free of porosity, and have excellent adherence to the substrate. The coatings mainly consist of Al-rich phases such as η-Fe2Al5, θ-FeAl3 and ?CrAl5. Oxidation resistance was studied by high-temperature tests. The formation mechanism of the Al-coatings was also investigated. This technique provides a new approach for industrial diffusion coatings with great energy and time savings.展开更多
基金supported by the National Natural Science Foundation of China(No.51274142)the Natural Science Foundation of Liaoning Province(No.2014028015)the Science&Technology Project of Shenyang City(No.F15-199-1-15)
文摘In this study, in order to investigate the influence of Cr element on the impact fracture process of ductile Ni-resistant alloyed iron at low temperature, different contents of Cr element were added to ductile Ni-resistant(DNR) austenitic alloyed iron. The experimental results show that Cr addition can increase the hardness of the DNR alloyed iron, but it has an destructive effect on low-temperature impact properties. Through the analysis of the dynamic load and absorbed energy of samples with different Cr contents in the impact fracture process, and the comparison of the impact fracture process at room and low temperatures, it reveals that Cr addition into the DNR alloyed iron can facilitate the formation of the carbide mixture in Mn23C6 and Cr23C6 with homogeneous and discontinuous distribution. Meanwhile, Cr addition also can improve the the maximum dynamic load and crack initiation energy at low temperature, but has no obvious effect on the yield behavior of the DNR alloyed iron in the impact fracture process. Compared with the impact crack propagation process at room temperature, the metastable propagation energy at low temperature declines significantly with an increase in Cr content. This is because the micro-cracks that caused by the carbides weaken the matrix, resulting in the decline of impact crack propagation resistance. The fracture analysis results also show that the impact fracture mechanism gradually transforms from ductile to brittle with an increase in Cr content at low temperature. It explains that too much Cr addition can lead to brittle fracture even though the austenitic matrix has a good toughness at low temperature.
基金Project(50271010) supported by the National Natural Science Foundation of China
文摘A method was presented to prepare aluminide coatings on metals by combining the pack aluminizing with the ball impact process. This technique applied mechanical vibration to a retort, which was loaded with pack-aluminizing powder, specimens and alloy balls. Pack aluminizing was carried out with repeated ball impact, which accelerated chemical reactions and atomic diffusion. Aluminide coatings were formed at a relatively lower temperature (below 600 ℃) and in a shorter treatment time, compared with the conventional pack aluminizing. The effects of the operation temperature and the treatment time on the formation of the coatings were analysed. The SEM, EDS and XRD analysis results show that the aluminide coatings appear to be homogeneous, with a high density and free of porosity, and have excellent adherence to the substrate. The coatings mainly consist of Al-rich phases such as η-Fe2Al5, θ-FeAl3 and ?CrAl5. Oxidation resistance was studied by high-temperature tests. The formation mechanism of the Al-coatings was also investigated. This technique provides a new approach for industrial diffusion coatings with great energy and time savings.
