Low temperature impact toughness and fracture mechanism of cast QT400-18L ductile iron with diferent Ni additions

Different contents of Ni(0.3wt.%to 1.2wt.%)were added to the QT400-18L ductile iron to investigate the effect of Ni addition on the impact toughness of cast ductile irons at low temperatures.The impact toughnesses of the samples at room and low temperatures were tested.The microstructures and fractographs were observed.Results show that with the increase of Ni addition there is a general trend of refinement of the ferrite matrix while the nodule density shows no obvious change.When the Ni content is 0.7wt.%,the matrix structure is the refined ferrite with a very small fraction(about 2%)of pearlite near the eutectic cell boundaries.When the Ni content is further increased,the fraction of pearlite increases significantly and reaches more than 5%when 1.2wt.%Ni is added.The impact toughness at room temperature increases as the content of Ni increases from 0.3 wt.%to 0.7 wt.%,but decreases as the Ni content further increases to 1.2wt.%due to the increase of pearlite fraction.The maximum value of the impact work is 18.5 J at room temperature with 0.7wt.%Ni addition.The average value of the impact work is still more than 13 J even at-30℃.In addition,the fracture mechanism changes from ductile manner to brittleness as the testing temperature decreases from 20℃to-60℃.

Physical, Psychological, and Social Health Impact of Temperature Rise Due to Urban Heat Island Phenomenon and Its Associated Factors

The Urban Heat Island Effect（UHI）has now become a commonly observed phenomenon worldwide.Indeed,it has become a significant environmental effect of urbanisation.In Malaysia,research results showed that UHI effects are very evident in several cities such as Kuala Lumpur and Putrajaya.UHI effect has long been observed to cause temperature of cities.

Low temperature impact strength of heavy section ductile iron castings:effects of microstructure and chemical composition

A foundry research project has been recently initiated at RTIT in order to better understand the fabrication of as-cast heavy section DI parts meeting high impact energy requirements at low temperatures.The experimental castings have the following dimensions 180 mm x 180 mm x 190 mm.The achieved as-cast Charpy impact strengths were as follows:17 J (RT),16 J (-20℃) and 11 J (-40℃).The foundry process,the chemical composition and the microstructure of this experimental casting are compared to the ones of various examples in order to show the detrimental effects of residual elements,microshrinkage and microcarbide on the impact properties.Finally,quality index empirical models (based on casting chemical compositions) are used to analyse the impact tests results.This paper illustrates that an adequate nodule count can contribute to reducing the detrimental effects of the residual elements and microsegregation.

Impact of Temperature Variation on Performance of Carbon Nanotube Field-Effect Transistor-Based on Chaotic Oscillator:A Quantum Simulation Study

We evaluate the impact of temperature on the output behavior of a carbon nanotube field effect transistor （CNFET） based chaotic generator. The sources cause the variations in both current-voltage characteristics of the CNFET device and an overall chaotic circuit is pointed out. To verify the effect of temperature variation on the output dynamics of the chaotic circuit, a simulation is performed by employing the CNFET compact model of Wong et al. in HSPICE with a temperature range from -100℃ to 100℃. The obtained results with time series, frequency spectra, and bifurcation diagram from the simulation demonstrate that temperature plays a significant role in the output dynamics of the CNFET-based chaotic circuit. Thus, temperature-related issues should be taken into account while designing a high-quality chaotic generator with high stability.

Low temperature impact toughness of laser hybrid welded joint of high strength low alloy steel

High strength low alloy steel with 16 mm thickness was welded by using high power laser hybrid welding. Microstrueture was characterized by using optical microscopy, scanning electron microscopy （ SEM ） , transmission electron microscopy （TEM） and selected area electron diffraction （SAED）. Low temperature impact toughness was estimated by using Charpy V-notch impact samples selected from the upper part and the lower part at the same heterogeneous joint. Results show that the low temperature impact absorbed energies of weld metal are （202,180,165 J） of upper samples and （178,145,160 J） of lower samples, respectively. All of them increase compared to base metal. The embrittlement of HAZ does not occur. Weld metal primarily consists of refined carbide free bainite and a little granular bainite since laser hybrid welding owns the character of low heat input. Retained austenite constituent film ＂locates among the lath structure of bainitie ferrite. Refined bainitic ferrite lath and retained austenite constituent film provide better low temperature impact toughness compared to base metal.

Aerosol deposition technology and its applications in batteries

Aerosol deposition(AD)method is a kind of additive manufacturing technology for fabricating dense films such as metals and ceramics at room temperature.It resolves the challenge of integrating ceramic films onto temperaturesensitive substrates,including metals,glasses,and polymers.It should be emphasized that the AD is a spray coating technology that uses powder without thermal assistance to generate films with high density.Compared to the traditional sputter-based approach,the AD shows several advantages in efficiency,convenience,better interfacial bonding and so on.Therefore,it opens some possibilities to the field of batteries,especially all-solidstate batteries(ASSBs)and draws much attention not only for research but also for large scale applications.The purpose of this work is to provide a critical review on the science and technology of AD as well as its applications in the field of batteries.The process,mechanism and effective parameters of AD,and recent developments in AD applications in the field of batteries will be systematically reviewed so that a trend for AD will be finally provided.

Energy Separation and Explicit Dynamic Analysis of Low Temperature Impact Toughness of Transmission Tower Material Q420B

To determine the physical significance of the impact toughness parameters and accurately characterize the low temperature impact toughness of transmission tower material Q420 B,the finite element model of Charpy impact test is established on the basis of experiment.The simulation and test results are verified,and the specimen fracture is analyzed by scanning electron microscope.The formation and growth mechanism of the crack are dynamically analyzed.On this basis,energy separation method is used to investigate the effect of low temperature on impact toughness.The results show that the simulation and test results are in good agreement,and the ductile-brittle transition temperature of Q420 B is about-50 ℃.The breaking process of the specimen is divided into the crack formation and propagation.When temperature drops from 20 to-60 ℃,the crack propagation energy decreases from 51.0 to 11.9 J,the crack formation energy reduces from 39.9 to 15.8 J,and the fracture time of the material drops from 1.8 to 0.6 ms.

Simulation study on heat-affected zone of high-strain X80 pipeline steel

The microstructure evolution and impact-toughness variation of heat-affected zone（HAZ）in X80 highstrain pipeline steel were investigated via a welding thermal-simulation technique,Charpy impact tests,and scanning electron microscopy observations under different welding heat inputs and peak temperatures.The results indicate that when heat input was between 17 and 25kJ·cm^（-1）,the coarse-grained heat-affected zone showed improved impact toughness.When the heat input was increased further,the martensite-austenite（M-A）islands transformed from fine lath into a massive block.Therefore,impact toughness was substantially reduced.When the heat input was 20kJ·cm^（-1） and the peak temperature of the first thermal cycle was between 900 and 1300°C,a higher impact toughness was obtained.When heat input was 20kJ·cm^（-1） and the peak temperature of the first thermal cycle was 1300°C,the impact toughness value at the second peak temperature of 900°C was higher than that at the second peak temperature of 800°C because of grain refining and uniformly dispersed M-A constituents in the matrix of bainite.