The effects of Mg and semi solid processing on the creep properties ofA356 A1 alloy were investigated. The results show that the dislocation climb controlled creep is the dominant creep mechanism and it is not affecte...The effects of Mg and semi solid processing on the creep properties ofA356 A1 alloy were investigated. The results show that the dislocation climb controlled creep is the dominant creep mechanism and it is not affected by the semi solid processing and further addition of Mg. Mg improves the alloy creep properties probably by forming large Chinese script Mg2Si compounds at the interdendritic regions. The semi solid processed specimens exhibit better creep properties in comparison with the as cast ones. It is attributed to the reduction in the stacking fault energy resulting from the significant dissolution of Mg in the a（A1） phase.展开更多
Microstructure and creep properties of AZ61 alloy containing 1 and 3 wt.% Ca were investigated. The creep properties were examined using impression method under different stresses between 200 and 500 MPa at the temper...Microstructure and creep properties of AZ61 alloy containing 1 and 3 wt.% Ca were investigated. The creep properties were examined using impression method under different stresses between 200 and 500 MPa at the temperature ranging from 423 to 491 K. The microstructure of AZ61 alloy contains α(Mg) matrix and Mg17 Al12 intermetallic phases. It is shown that adding Ca to AZ61 alloy reduces the amount of Mg17 Al12 phase via forming(Mg,Al)2 Ca phase;furthermore, increasing the Ca content to 3 wt.% leads to the formation of(Mg,Al)2 Ca phase, as well as the elimination of the Mg17 Al12 phase. Creep properties of AZ61 alloy are improved with the Ca addition. The improvement in creep properties is attributed to the reduction in the amount of Mg17 Al12 phase and the formation of(Mg,Al)2 Ca phase with high thermal stability. According to the obtained creep data, it is concluded that the pipe diffusion-climb controlled dislocation creep is the dominant creep mechanism and Ca addition has no influence on this mechanism. The effect of pre-deformation on the creep properties of AZ61+3%Ca alloy reveals that the creep resistance of the alloy depends on the continuity of(Mg,Al)2 Ca phase. It is decreased by reducing the phase continuity.展开更多
The results of a theoretical and finite element (FE) investigation of a two-material impression creep test method, using a rectangular indenter, are presented. The method uses a general formulation for steady-state cr...The results of a theoretical and finite element (FE) investigation of a two-material impression creep test method, using a rectangular indenter, are presented. The method uses a general formulation for steady-state creep deformation for multi-material components in conjunction with the results of FE analyses. The practical application of the proposed technique, in determining the secondary creep properties of heat-affected zone (HAZ) materials in welds, for which conventional creep testing methods cannot be used, is considered. A number of numerical examples are used to describe solution procedures and to verify the method.展开更多
The effects of addition of calcium up to 4 wt.% on the microstructure and creep properties of Mg-4 Sn alloys were investigated by the impression creep test. Impression creep tests were performed in temperature range b...The effects of addition of calcium up to 4 wt.% on the microstructure and creep properties of Mg-4 Sn alloys were investigated by the impression creep test. Impression creep tests were performed in temperature range between 445 and 475 K under normalized stresses σ/G(where σ is the stress;G is the shear modulus) between 0.0225 and 0.035. Optical microscopy and scanning electron microscopy were used to study the microstructure of samples. It is observed that the addition of Ca more than 2 wt.% suppresses less stable Mg Sn2 phase, and instead forms more thermally stable phases of Ca-Mg-Sn and Mg2 Ca at the grain boundaries which improve the creep resistance of Mg-4 Sn alloys. According to the stress exponents(6.04<n<6.89) and activation energies(101.37 k J/mol<Q<113.8 k J/mol) which were obtained from the impression creep tests, it is concluded that the pipe diffusion climb controlled dislocation creep is the dominant creep mechanism.展开更多
Bead-on-plate friction stir welds were made on P91 alloy with low and high rotational speeds(100 and 1000 RPM) to study their effects on weld microstructural changes and impression creep behavior. Temperatures experie...Bead-on-plate friction stir welds were made on P91 alloy with low and high rotational speeds(100 and 1000 RPM) to study their effects on weld microstructural changes and impression creep behavior. Temperatures experienced by the stir zone were recorded at the weld tool tip. Different zones of welds were characterized for their microstructural changes, hardness and creep behavior(by impression creep tests). The results were compared with submerged arc fusion weld. Studies revealed that the stir zone temperature with 100 RPM was well below A_(c1) temperature of P91 steel while it was above A_(c3) with 1000 RPM. The results suggest that the microstructural degradation in P91 welds can be controlled by low temperature friction stir welding technique.展开更多
文摘The effects of Mg and semi solid processing on the creep properties ofA356 A1 alloy were investigated. The results show that the dislocation climb controlled creep is the dominant creep mechanism and it is not affected by the semi solid processing and further addition of Mg. Mg improves the alloy creep properties probably by forming large Chinese script Mg2Si compounds at the interdendritic regions. The semi solid processed specimens exhibit better creep properties in comparison with the as cast ones. It is attributed to the reduction in the stacking fault energy resulting from the significant dissolution of Mg in the a（A1） phase.
文摘Microstructure and creep properties of AZ61 alloy containing 1 and 3 wt.% Ca were investigated. The creep properties were examined using impression method under different stresses between 200 and 500 MPa at the temperature ranging from 423 to 491 K. The microstructure of AZ61 alloy contains α(Mg) matrix and Mg17 Al12 intermetallic phases. It is shown that adding Ca to AZ61 alloy reduces the amount of Mg17 Al12 phase via forming(Mg,Al)2 Ca phase;furthermore, increasing the Ca content to 3 wt.% leads to the formation of(Mg,Al)2 Ca phase, as well as the elimination of the Mg17 Al12 phase. Creep properties of AZ61 alloy are improved with the Ca addition. The improvement in creep properties is attributed to the reduction in the amount of Mg17 Al12 phase and the formation of(Mg,Al)2 Ca phase with high thermal stability. According to the obtained creep data, it is concluded that the pipe diffusion-climb controlled dislocation creep is the dominant creep mechanism and Ca addition has no influence on this mechanism. The effect of pre-deformation on the creep properties of AZ61+3%Ca alloy reveals that the creep resistance of the alloy depends on the continuity of(Mg,Al)2 Ca phase. It is decreased by reducing the phase continuity.
基金the Engineering&Physics Science Research Council(EPSRC)the Institution of Mechanical Engineers(IMechE),UK,Ior financial support.
文摘The results of a theoretical and finite element (FE) investigation of a two-material impression creep test method, using a rectangular indenter, are presented. The method uses a general formulation for steady-state creep deformation for multi-material components in conjunction with the results of FE analyses. The practical application of the proposed technique, in determining the secondary creep properties of heat-affected zone (HAZ) materials in welds, for which conventional creep testing methods cannot be used, is considered. A number of numerical examples are used to describe solution procedures and to verify the method.
文摘The effects of addition of calcium up to 4 wt.% on the microstructure and creep properties of Mg-4 Sn alloys were investigated by the impression creep test. Impression creep tests were performed in temperature range between 445 and 475 K under normalized stresses σ/G(where σ is the stress;G is the shear modulus) between 0.0225 and 0.035. Optical microscopy and scanning electron microscopy were used to study the microstructure of samples. It is observed that the addition of Ca more than 2 wt.% suppresses less stable Mg Sn2 phase, and instead forms more thermally stable phases of Ca-Mg-Sn and Mg2 Ca at the grain boundaries which improve the creep resistance of Mg-4 Sn alloys. According to the stress exponents(6.04<n<6.89) and activation energies(101.37 k J/mol<Q<113.8 k J/mol) which were obtained from the impression creep tests, it is concluded that the pipe diffusion climb controlled dislocation creep is the dominant creep mechanism.
文摘Bead-on-plate friction stir welds were made on P91 alloy with low and high rotational speeds(100 and 1000 RPM) to study their effects on weld microstructural changes and impression creep behavior. Temperatures experienced by the stir zone were recorded at the weld tool tip. Different zones of welds were characterized for their microstructural changes, hardness and creep behavior(by impression creep tests). The results were compared with submerged arc fusion weld. Studies revealed that the stir zone temperature with 100 RPM was well below A_(c1) temperature of P91 steel while it was above A_(c3) with 1000 RPM. The results suggest that the microstructural degradation in P91 welds can be controlled by low temperature friction stir welding technique.
