Impulse turbine, working as a typical self-rectifying turbine, is recently utilized for the oscillating water column(OWC) wave energy converters, which can rotate in the same direction under the bi-directional air f...Impulse turbine, working as a typical self-rectifying turbine, is recently utilized for the oscillating water column(OWC) wave energy converters, which can rotate in the same direction under the bi-directional air flows. A numerical model established in Fluent is validated by the corresponding experimental results. The flow fields, pressure distribution and dimensionless evaluating coefficients can be calculated and analyzed. Effects of the rotor solidity varying with the change of blade number are investigated and the suitable solidity value is recommended for different flow coefficients.展开更多
Wave energy is a renewable source with significant amount in relation to the global demand. A good concept of a device applied to extract this type of energy is the onshore oscillating water column wave energy convert...Wave energy is a renewable source with significant amount in relation to the global demand. A good concept of a device applied to extract this type of energy is the onshore oscillating water column wave energy converter(OWC-WEC). This study shows a numerical analysis of the diameter determination of two types of turbines, Wells and Impulse, installed in an onshore OWC device subjected to a hypothetical sea state. Commercial software FLUENT?,which is based on RANS-VoF(Reynolds-Averaged Navier-Stokes equations and Volume of Fluid technique), is employed. A methodology that imposes air pressure on the chamber, considering the air compressibility effect, is used. The mathematical domain consists of a 10 m deep flume with a 10 m long and 10 m wide OWC chamber at its end(geometry is similar to that of the Pico's plant installed in Azores islands, Portugal). On the top of the chamber, a turbine works with air exhalation and inhalation induced by the water free surface which oscillates due to the incident wave. The hypothetical sea state, represented by a group of regular waves with periods from 6 to 12 s and heights from 1.00 to 2.00 m(each wave with an occurrence frequency), is considered to show the potential of the presented methodology. Maximum efficiency(relation between the average output and incident wave powers) of46% was obtained by using a Wells turbine with the diameter of 2.25 m, whereas the efficiency was 44% by an Impulse turbine with the diameter of 1.70 m.展开更多
A fixed oscillating water column(OWC)-type wave energy converter consists of an air chamber,an air turbine and a generator.The energy conversion processes are the primary conversion in an air chamber and the secondary...A fixed oscillating water column(OWC)-type wave energy converter consists of an air chamber,an air turbine and a generator.The energy conversion processes are the primary conversion in an air chamber and the secondary conversion of the turbine.For the practical use,it is necessary to develop a design method which can consider the incident wave motion,the motion of the internal free surface affected in the structure such as a partly submerged wall,the fluctuation of air pressure in an air chamber,and the rotation of the air turbine.At here,the authors carried out the wave tank tests using the model OWC equipped with the impulse turbine and a generator to obtain the experimental data needed to make this design method.As the result,the efficiencies of the three cases with different speed ratio between generator and turbine,and the effects of the curtain wall depth and the wave length on the energy conversion performance were clarified.展开更多
A pair of unidirectional turbines(UT)can operate in oscillatory airflow without additional units.However,this arrangement suffers from poor flow rectification.A fluidic diode(FD)offers variable hydrodynamic resistance...A pair of unidirectional turbines(UT)can operate in oscillatory airflow without additional units.However,this arrangement suffers from poor flow rectification.A fluidic diode(FD)offers variable hydrodynamic resistance based on the flow direction,and this can be coupled with UT to improve flow rectification.In this work,a numerical investigation on the effect of FD with UT is presented using the commercial fluid dynamics software ANSYS Fluent 16.1 with k-ωSST turbulence closure model.Periodic domains of UT and FD are numerically validated individually with experimental results.Later,both are coupled to obtain the combined effect,and these results are compared with the analytical approach.It was observed that coupling FD with UT improved the unit's performance at the lower flow coefficient(<1),but its performance decreased as the flow coefficient increased.Due to the diode's presence,fluid leaving the turbine experiences higher resistance at a higher flow coefficient,which decreases the overall performance of the combined unit.展开更多
This paper aims to develop a generic optimisation method for Pelton turbine runners using computational fluid dynamics (CFD). Two different initial runners are optimised to achieve more generic results. A simple buc...This paper aims to develop a generic optimisation method for Pelton turbine runners using computational fluid dynamics (CFD). Two different initial runners are optimised to achieve more generic results. A simple bucket geometry based on existing bibliography is parameterised and initially optimised using fast Lagrangian solver (FLS). It is then further optimised with a more accurate method using ANSYS Fluent. The second geometry is a current commercial geometry with good initial performance and is optimised using ANSYS CFX. The analytical results provided by CFX and Fluent simulations are used to analyse the characteristics of the flow for different runner geometries.展开更多
A numerical case study on identifying the optimum number of buckets for a Pelton turbine is presented. Three parameters: number of buckets, bucket radial position and bucket angular position are grouped since they ar...A numerical case study on identifying the optimum number of buckets for a Pelton turbine is presented. Three parameters: number of buckets, bucket radial position and bucket angular position are grouped since they are found to be interrelated. By identifying the best combination of the radial and angular position for each number of buckets it is shown that reduction in the number of buckets beyond the limit suggested by the available literature can improve the efficiency and be beneficial with regard to the manufacturing complexity and cost perspective. The effect of this reduction in the number of buckets was confirmed experimentally.展开更多
To obtain a high specific work output,the large pressure ratios across the turbine are required.This can be achieved using a supersonic turbine.When the fluid mass flow is low,the impulse kind of one or two stages sup...To obtain a high specific work output,the large pressure ratios across the turbine are required.This can be achieved using a supersonic turbine.When the fluid mass flow is low,the impulse kind of one or two stages supersonic turbine is employed.To prevent losses due to low blade aspect ratio and issues related to manufacturing and industrial problems,the turbine is used in partial admission conditions.Studies show that the turbine efficiency is highly dependent on the amount of partial admission coefficient.The turbine efficiency in full admission is high,but the use of partial admission lowers the additional losses.Therefore,there will be a degree of partial admission in which the turbine will have the highest efficiency.The aim of this work is to achieve the optimum partial admission for a special impulse turbine as a case study.Therefore,in the beginning,an appropriate model of losses is presented.Then,using a nonlinear design optimization code,the partial admission of an impulse supersonic turbine is optimized.This code is written using a genetic algorithm.Then,using three-dimensional numerical analysis,the optimal model will be selected.In the optimization problem,the turbine efficiency is the objective function.The amount of design parameters and constraints used in this process are ten and eight,respectively.After the optimization process,prototypes of designed and modified turbines are made and tested.Test results were compared and analyzed.The results showed that the turbine efficiency is improved between 2.5%and 3%depending on various operation conditions.展开更多
Bi-directional turbines combined with rotary motors may be a feasible option for developing high power thermoacoustic generators with low cost.A general expression for the acoustic characteristics of the bidirectional...Bi-directional turbines combined with rotary motors may be a feasible option for developing high power thermoacoustic generators with low cost.A general expression for the acoustic characteristics of the bidirectional turbine was proposed based on theoretical derivation,which was validated by computational fluid dynamics modeling of an impulse turbine with fixed guide vanes.The structure of the turbine was optimized primarily using steady flow with an efficiency of near 70%(the shaft power divided by the total energy consumed by the turbine).The turbine in the oscillating flow was treated in a lumped-parameter model to extract the acoustic impedance characteristics from the simulation results.The key acoustic impedance characteristic of the turbine was the resistance and inertance due to complex flow condition in the turbine,whereas the capacitance was treated as an adiabatic case because of the large-scale flow channel relative to the heat penetration depth.Correlations for the impedance were obtained from both theoretical predictions and numerical fittings.The good fit of the correlations shows that these characteristics are valid for describing the bi-directional turbine,providing the basis for optimization of the coupling between the thermoacoustic engine and the turbine using quasi-one-dimensional theory in the frequency domain.展开更多
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51279190 and 51311140259)the Shandong Province Natural Science Foundation for Distinguished Young Scholars(Grant No.JQ201314)
文摘Impulse turbine, working as a typical self-rectifying turbine, is recently utilized for the oscillating water column(OWC) wave energy converters, which can rotate in the same direction under the bi-directional air flows. A numerical model established in Fluent is validated by the corresponding experimental results. The flow fields, pressure distribution and dimensionless evaluating coefficients can be calculated and analyzed. Effects of the rotor solidity varying with the change of blade number are investigated and the suitable solidity value is recommended for different flow coefficients.
文摘Wave energy is a renewable source with significant amount in relation to the global demand. A good concept of a device applied to extract this type of energy is the onshore oscillating water column wave energy converter(OWC-WEC). This study shows a numerical analysis of the diameter determination of two types of turbines, Wells and Impulse, installed in an onshore OWC device subjected to a hypothetical sea state. Commercial software FLUENT?,which is based on RANS-VoF(Reynolds-Averaged Navier-Stokes equations and Volume of Fluid technique), is employed. A methodology that imposes air pressure on the chamber, considering the air compressibility effect, is used. The mathematical domain consists of a 10 m deep flume with a 10 m long and 10 m wide OWC chamber at its end(geometry is similar to that of the Pico's plant installed in Azores islands, Portugal). On the top of the chamber, a turbine works with air exhalation and inhalation induced by the water free surface which oscillates due to the incident wave. The hypothetical sea state, represented by a group of regular waves with periods from 6 to 12 s and heights from 1.00 to 2.00 m(each wave with an occurrence frequency), is considered to show the potential of the presented methodology. Maximum efficiency(relation between the average output and incident wave powers) of46% was obtained by using a Wells turbine with the diameter of 2.25 m, whereas the efficiency was 44% by an Impulse turbine with the diameter of 1.70 m.
基金This investigation was carried out as a continuation of the“Program for the Promotion of New Energy Infrastructure Development”,supported by the Mitsubishi Research Institute(MRI)/the Ministry of Economy,Trade and Industry(METI),Japan.
文摘A fixed oscillating water column(OWC)-type wave energy converter consists of an air chamber,an air turbine and a generator.The energy conversion processes are the primary conversion in an air chamber and the secondary conversion of the turbine.For the practical use,it is necessary to develop a design method which can consider the incident wave motion,the motion of the internal free surface affected in the structure such as a partly submerged wall,the fluctuation of air pressure in an air chamber,and the rotation of the air turbine.At here,the authors carried out the wave tank tests using the model OWC equipped with the impulse turbine and a generator to obtain the experimental data needed to make this design method.As the result,the efficiencies of the three cases with different speed ratio between generator and turbine,and the effects of the curtain wall depth and the wave length on the energy conversion performance were clarified.
基金performed as a Grant-in-Aid for Early-Career Scientists(No.22K14434)supported by the Japan Society for the Promotion of Science(JSPS)JSPS for their financial help in conducting this studyⅡT Madras for the computational facility and financial help to present part of the work in AJWTF-2020。
文摘A pair of unidirectional turbines(UT)can operate in oscillatory airflow without additional units.However,this arrangement suffers from poor flow rectification.A fluidic diode(FD)offers variable hydrodynamic resistance based on the flow direction,and this can be coupled with UT to improve flow rectification.In this work,a numerical investigation on the effect of FD with UT is presented using the commercial fluid dynamics software ANSYS Fluent 16.1 with k-ωSST turbulence closure model.Periodic domains of UT and FD are numerically validated individually with experimental results.Later,both are coupled to obtain the combined effect,and these results are compared with the analytical approach.It was observed that coupling FD with UT improved the unit's performance at the lower flow coefficient(<1),but its performance decreased as the flow coefficient increased.Due to the diode's presence,fluid leaving the turbine experiences higher resistance at a higher flow coefficient,which decreases the overall performance of the combined unit.
基金Lancaster University Renewable Energy Group and Fluid Machinery Groupthe Laboratory of Hydraulic Turbo Machines at the National Technical University of Athens+1 种基金Gilbert Gilkes and Gordon Ltdthe EU ERASMUS programme for the financial support
文摘This paper aims to develop a generic optimisation method for Pelton turbine runners using computational fluid dynamics (CFD). Two different initial runners are optimised to achieve more generic results. A simple bucket geometry based on existing bibliography is parameterised and initially optimised using fast Lagrangian solver (FLS). It is then further optimised with a more accurate method using ANSYS Fluent. The second geometry is a current commercial geometry with good initial performance and is optimised using ANSYS CFX. The analytical results provided by CFX and Fluent simulations are used to analyse the characteristics of the flow for different runner geometries.
基金the support of Lancaster University Renewable Energy Group and Fluid Machinery Group
文摘A numerical case study on identifying the optimum number of buckets for a Pelton turbine is presented. Three parameters: number of buckets, bucket radial position and bucket angular position are grouped since they are found to be interrelated. By identifying the best combination of the radial and angular position for each number of buckets it is shown that reduction in the number of buckets beyond the limit suggested by the available literature can improve the efficiency and be beneficial with regard to the manufacturing complexity and cost perspective. The effect of this reduction in the number of buckets was confirmed experimentally.
文摘To obtain a high specific work output,the large pressure ratios across the turbine are required.This can be achieved using a supersonic turbine.When the fluid mass flow is low,the impulse kind of one or two stages supersonic turbine is employed.To prevent losses due to low blade aspect ratio and issues related to manufacturing and industrial problems,the turbine is used in partial admission conditions.Studies show that the turbine efficiency is highly dependent on the amount of partial admission coefficient.The turbine efficiency in full admission is high,but the use of partial admission lowers the additional losses.Therefore,there will be a degree of partial admission in which the turbine will have the highest efficiency.The aim of this work is to achieve the optimum partial admission for a special impulse turbine as a case study.Therefore,in the beginning,an appropriate model of losses is presented.Then,using a nonlinear design optimization code,the partial admission of an impulse supersonic turbine is optimized.This code is written using a genetic algorithm.Then,using three-dimensional numerical analysis,the optimal model will be selected.In the optimization problem,the turbine efficiency is the objective function.The amount of design parameters and constraints used in this process are ten and eight,respectively.After the optimization process,prototypes of designed and modified turbines are made and tested.Test results were compared and analyzed.The results showed that the turbine efficiency is improved between 2.5%and 3%depending on various operation conditions.
基金supported by the National Key Research and Development Program of China(Grant No.2016YFB-0901403)the National Natural Science Foundation of China(Grant No.51606208).
文摘Bi-directional turbines combined with rotary motors may be a feasible option for developing high power thermoacoustic generators with low cost.A general expression for the acoustic characteristics of the bidirectional turbine was proposed based on theoretical derivation,which was validated by computational fluid dynamics modeling of an impulse turbine with fixed guide vanes.The structure of the turbine was optimized primarily using steady flow with an efficiency of near 70%(the shaft power divided by the total energy consumed by the turbine).The turbine in the oscillating flow was treated in a lumped-parameter model to extract the acoustic impedance characteristics from the simulation results.The key acoustic impedance characteristic of the turbine was the resistance and inertance due to complex flow condition in the turbine,whereas the capacitance was treated as an adiabatic case because of the large-scale flow channel relative to the heat penetration depth.Correlations for the impedance were obtained from both theoretical predictions and numerical fittings.The good fit of the correlations shows that these characteristics are valid for describing the bi-directional turbine,providing the basis for optimization of the coupling between the thermoacoustic engine and the turbine using quasi-one-dimensional theory in the frequency domain.