In this paper,since the Avalanche Photo Diode(APD)for Light-to-Voltage LTV conversion uses a high voltage in the operating range unlike other Photo Diodes(PD),the quenching resistor must be connected in series to prev...In this paper,since the Avalanche Photo Diode(APD)for Light-to-Voltage LTV conversion uses a high voltage in the operating range unlike other Photo Diodes(PD),the quenching resistor must be connected in series to prevent overcurrent when using the Transimpedance Amplifier(TIA).In such a case,quenching resistance may affect the transfer function of the TIA circuit,resulting in serious stability.Therefore,in this paper,by analyzing the effect of APD quenching resistance on the voltage and current loop transfer function of TIA,we proposed a loop analysis and a method for determining the quenching resistance value to improve stability.A TIA circuit with quenching resistance was designed by the proposed method and its operational stability was verified through simulation and chip fabrication.展开更多
Bainite microstructures have become increasingly attractive for the development of advanced high-strength steel owing to their balanced strength-plasticity properties.In this study, the final microstructure and mechan...Bainite microstructures have become increasingly attractive for the development of advanced high-strength steel owing to their balanced strength-plasticity properties.In this study, the final microstructure and mechanical properties of a quenching and partitioning(QP) steel sample after two distinct QP processes were analyzed.The results reveal that martensite transformation after quenching resulted in a lathed morphology with higher yield strength and hole expansion ratio.In contrast, bainite transformation after quenching resulted in the formation of a blocky microstructure composed of bainitic ferrite retained austenite and nanoscale precipitates during the subsequent phase transformation at a higher temperature.This kind of final microstructure is beneficial to the elongation of QP steel but detrimental to the hole expansion ratio.展开更多
Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under indust...Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.展开更多
The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the proper...The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the properties and microstructure of G115 steel was explored.The samples that were quenched and tempered twice had a higher tensile strength at room temperature and 650 ℃,and the impact energy was significantly improved.The strength and impact energy increased in proportion to the increase in the first quenching temperature.The microstructure differences between the single and double quenched and tempered samples were examined using metallographic microscopy and scanning electron microscopy.The grain size of the double quenched and tempered samples was finer than that of the single quenched and tempered samples, and the tempered martensite lath is more visible, as are the carbides and other precipitates, which are finer and more uniformly distributed.As the first quenching temperature increased, the grains became coarser but more uniform.展开更多
Cu-Ni-Sn spinodal alloys(Spinodal bronze)are potential materials with robust applications in components associated with defence applications like bearings,propellers,bushes,and shafts of heavily loaded aircraft,off-ro...Cu-Ni-Sn spinodal alloys(Spinodal bronze)are potential materials with robust applications in components associated with defence applications like bearings,propellers,bushes,and shafts of heavily loaded aircraft,off-road vehicles,and warships.This paper presents a comparative study using water,Brine solution,and SAE 40 oil as the quenching media in regular bronze(Cu-6Sn)and spinodal bronze(Cu-9Ni-6Sn)alloys.Morphological analysis was conducted by optical microscopy,transmission electron microscopy(TEM),and X-ray diffraction technique(XRD)on bronze and spinodal bronze samples immersed in the three different quenching media to understand the grain size and hardness values better.Tribological analysis was performed to analyze the effect of quenching media on the wear aspects of bronze and spinodal bronze samples.The hardness value of the brine-aged spinodal bronze samples was as high as 320 Hv,and the grain size was very low in the range of 60μm.A quantitative comparison between brine-aged regular bronze and brine-aged spinodal bronze showed that the hardness(Hv)was almost 80%higher for brine-aged spinodal bronze.Further,the grain size was approximately 30%finer for spinodal bronze when compared with regular bronze.When the load was increased in spinodal bronze samples,there was an initial dip in wear rate followed by a marginal increase.There was a steady increase in friction coefficient with a rise in load for brine-aged regular bronze and spinodal bronze samples.These results indicate that brine solution is the most effective quenching medium for cast Cu-Ni-Sn spinodal alloys.展开更多
Multi-phase nitrides bonded silicon carbide lintel blocks were prepared using industrial SiC(SiC≥98 mass%,3-0.5,≤0.5 and≤0.044 mm),Si powder(Si≥98 mass%,≤0.044 mm),and SiO2 micropowder(SiO2≥96 mass%,d50=0.15 pm)...Multi-phase nitrides bonded silicon carbide lintel blocks were prepared using industrial SiC(SiC≥98 mass%,3-0.5,≤0.5 and≤0.044 mm),Si powder(Si≥98 mass%,≤0.044 mm),and SiO2 micropowder(SiO2≥96 mass%,d50=0.15 pm)as raw materials,and calcium lignosulfonate as the additive,batching,mixing,and molding on a vibration pressure molding machine,drying and then firing at 1420℃for 10 h in high-purity N2.The apparent porosity,the bulk density,the cold modulus of rupture,the hot modulus of rupture,and the linear expansion coefficient of the samples were tested.The phase composition and the microstructure of the samples at different nitriding depths(50,100,and 150 mm)were analyzed by XRD and SEM.The field application effects of the blocks were studied.The results show that:(1)the multi-phase nitrides bonded silicon carbide refractories can dynamically adjust their own phase composition and minimize structural and thermal stresses,improving the service life of key parts of dry quenching furnaces;(2)calcium lignosulfonate can improve the nitriding micro-environment of multi-phase nitrides bonded silicon carbide lintel blocks,successfully increasing the effective nitriding thickness of the blocks to 300 mm;(3)Sinosteel LI RR provides a unique concept in the design of materials and block types as well as the stable and scientific overall structure,promoting the industrialization process of dry quenching furnaces with long service life in China.展开更多
Manipulating nonlinear excitations,including solitons and vortices,is an essential topic in quantum many-body physics.A new progress in this direction is a protocol proposed in[Phys.Rev.Res.2043256(2020)]to produce da...Manipulating nonlinear excitations,including solitons and vortices,is an essential topic in quantum many-body physics.A new progress in this direction is a protocol proposed in[Phys.Rev.Res.2043256(2020)]to produce dark solitons in a one-dimensional atomic Bose–Einstein condensate(BEC)by quenching inter-atomic interaction.Motivated by this work,we generalize the protocol to a two-dimensional BEC and investigate the generic scenario of its post-quench dynamics.For an isotropic disk trap with a hard-wall boundary,we find that successive inward-moving ring dark solitons(RDSs)can be induced from the edge,and the number of RDSs can be controlled by tuning the ratio of the after-and before-quench interaction strength across different critical values.The role of the quench played on the profiles of the density,phase,and sound velocity is also investigated.Due to the snake instability,the RDSs then become vortex–antivortex pairs with peculiar dynamics managed by the initial density and the after-quench interaction.By tuning the geometry of the box traps,demonstrated as polygonal ones,more subtle dynamics of solitons and vortices are enabled.Our proposed protocol and the discovered rich dynamical effects on nonlinear excitations can be realized in near future cold-atom experiments.展开更多
The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required...The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required these days,it is necessary to predict the quality of heat treatment by CAE(Computer Added Engineering),shorten the product development period.The calculation of the vapor film collapses in a simple and practical time in order to improve the product performance.However,in the past,in order to formulate the vapor film collapse on a simulation,it was necessary to perform a very large amount of computational calculation CFD(computational fluid dynamics),which was a problem in terms of computer resources and the model of vapor film collapse.In addition,this phenomenon has a complexity behavior of the phenomenon in iterative processing,which also complicates the calculation.In this study,the vapor film collapse phenomenon is easily visualized using self-organized cellular automaton simulation which includes the phenomena of“vapor film thickness and its fluctuation”,“flow disturbance”,“surface step of workpiece”,and“decrease of cooling due to r shape of surface”.The average cooling state and repeated fluctuations of the cooling state were reproduced by this method.展开更多
Quorum sensing(QS)is a regulatory system that regulates the behavior of microbial populations by sensing the concentration of signal molecules that are spontaneously produced and released by bacteria.The strategy of b...Quorum sensing(QS)is a regulatory system that regulates the behavior of microbial populations by sensing the concentration of signal molecules that are spontaneously produced and released by bacteria.The strategy of blocking the QS system and inhibiting the production of virulence factors is termed as quorum quenching(QQ).This strategy attenuates virulence without killing the pathogens,thereby weakening the selective pressure on pathogens and postponing the evolution of QQ-mediated drug resistance.In recent years,there have been significant theoretical and practical developments in the field of QS and QQ.In particular,with the development and utilization of marine resources,more and more marine microbial species have been found to be regulated by these two mechanisms,further promoting the research progress of QS and QQ.In this review,we described the diversity of QS signals and QS-related regulatory systems,and then introduced mechanisms related to QS interference,with particular emphasis on the description of natural QQ enzymes and chemicals acting as QS inhibitors.Finally,the exploitation of quorum sensing quenchers and the practical application of QQ were introduced,while some QQ strategies were proposed as promising tools in different fields such as medicine,aquaculture,agriculture and biological pollution prevention areas.展开更多
A computer software to simulate the phase transformation during quenching is designed based on Avrami equation and Scheil additivity principle of incubation period. The isothermal transformation diagrams of supercoole...A computer software to simulate the phase transformation during quenching is designed based on Avrami equation and Scheil additivity principle of incubation period. The isothermal transformation diagrams of supercooled austenite are described by cubic spline functions. This software is possess of a good graphic interface of Windows style, can simulate the whole process in austenite decomposition during continuous cooling. If the cooling rate was given, the fraction of various microstructures transformed of austenite decomposition during continuous cooling at any temperature can be calculated. The simulation results are checked with the quenching experiment of 45 steel. The results indicate that the simulation results are comparatively close to the experimental results.展开更多
Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time,...Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.展开更多
The characteristics of γ′ precipitates in a superalloy quenched from 1050°C at different rates were investigated using field emission scanning electron microscope(FESEM).When quenched from 1050°C, the size...The characteristics of γ′ precipitates in a superalloy quenched from 1050°C at different rates were investigated using field emission scanning electron microscope(FESEM).When quenched from 1050°C, the size of primary aging γ′ precipitates has a small increase in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions and a drastic increase in the specimen that experienced a furnace-cooling-quenching condition.The cooling γ′ precipitates have unimodal distributions after quenching at the air-cooling rate and bimodal distributions after quenching at the furnace-cooling rate, but there are not these distributions in the specimens that experienced iced-brine-quenching and oil-quenching conditions.When aging at 760°C, the size of primary aging γ′ precipitates appears unaffected in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions.However, it has a drastic increase in the specimen that experienced a furnace-cooling-quenching condition, and it is interesting that the bigger cooling γ′ precipitates have a coalescence and octodendritic shape.The microhardness study indicates that the hardness has no variation in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions and has a drastic decrease in the specimens that experienced a furnace-cooling-quenching condition and obtains the minimum microhardness value 390.8 HV.展开更多
The determination method of catechol by fluorescence quenching was developed.The assay was based on the combination of the unique property of gold nanoparticles with tyrosinase enzymatic reaction.In the presence of ty...The determination method of catechol by fluorescence quenching was developed.The assay was based on the combination of the unique property of gold nanoparticles with tyrosinase enzymatic reaction.In the presence of tyrosinase,the fluorescence of gold nanoparticles was quenched by catechol which can be employed to detect catechol.Under the optimal conditions,a linear range 5.0×10^(-7)-1.0×10^(-3) mol L^(-1) and a detection limit 1.0×10^(-7) mol L^(-1) of catechol were obtained.o-Quinone intermediate produ...展开更多
In order to obtain the desired mechanical properties of quenching and tempering workpieces, as well as reduce the cracking tendency and distortion, a program of controllable quenching was established. Furthermore, a c...In order to obtain the desired mechanical properties of quenching and tempering workpieces, as well as reduce the cracking tendency and distortion, a program of controllable quenching was established. Furthermore, a computer-aided quenching system (CAQ) was also developed. The application samples of the CAQ system showed satisfactory results.展开更多
In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investig...In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investigated. The obtained results show that the La2Mg(Ni0.85Co0.15)9M0.1 (M=B, Cr) alloy electrodes are composed of (La, Mg)Ni3 phase, LaNi5 phase and a small amount of the LaNi2 phase. A trace of the Ni2B phase exists in the as-cast MB alloy, and the Ni2B phase in the alloy nearly disappears after rapid quenching. Rapid quenching technology can slightly improve the cycling life of the alloy. When the quenching rate increases from 0 m·s-1 (As-cast is defined as quenching rate of 0 m·s-1) to 30 m·s-1, the cycle lives of the MB, MCr alloys enhance from 86 and 87 cycles to 106 and 119 cycles, respectively. On the other hand, the average capacity decay rates of the MB, MCr alloys decrease from 1.7172 and 1.7178 mAh·g-1·cycle-1 to 1.5751 and 1.3060 mAh·g-1·cycle-1 after 86 charge-discharges cycling, respectively.展开更多
The effect of rare earth elements on quenching crack resistance of steel 9Cr2Mo was investigated by means of scanning electron microscopy (SEM) and optical microscopy. Experimental results show that, by adding RE elem...The effect of rare earth elements on quenching crack resistance of steel 9Cr2Mo was investigated by means of scanning electron microscopy (SEM) and optical microscopy. Experimental results show that, by adding RE elements to steel 9Cr2Mo, the number of quenching for crack initiation is increased. Meanwhile the propagation of quenching cracks is postponed and the paths of crack propagation are changed. Therefore, quenching crack resistance can be improved by adding RE elements to steel 9Cr2Mo.展开更多
文摘In this paper,since the Avalanche Photo Diode(APD)for Light-to-Voltage LTV conversion uses a high voltage in the operating range unlike other Photo Diodes(PD),the quenching resistor must be connected in series to prevent overcurrent when using the Transimpedance Amplifier(TIA).In such a case,quenching resistance may affect the transfer function of the TIA circuit,resulting in serious stability.Therefore,in this paper,by analyzing the effect of APD quenching resistance on the voltage and current loop transfer function of TIA,we proposed a loop analysis and a method for determining the quenching resistance value to improve stability.A TIA circuit with quenching resistance was designed by the proposed method and its operational stability was verified through simulation and chip fabrication.
文摘Bainite microstructures have become increasingly attractive for the development of advanced high-strength steel owing to their balanced strength-plasticity properties.In this study, the final microstructure and mechanical properties of a quenching and partitioning(QP) steel sample after two distinct QP processes were analyzed.The results reveal that martensite transformation after quenching resulted in a lathed morphology with higher yield strength and hole expansion ratio.In contrast, bainite transformation after quenching resulted in the formation of a blocky microstructure composed of bainitic ferrite retained austenite and nanoscale precipitates during the subsequent phase transformation at a higher temperature.This kind of final microstructure is beneficial to the elongation of QP steel but detrimental to the hole expansion ratio.
基金financially supported by the National Key Research and Development Program of China(No.2020YFF0218200)。
文摘Solution and quenching heat treatments are generally carried out in a roller hearth furnace for large-scale thick aluminum alloy plates.However,the asymmetric or uneven spray water flow rate is inevitable under industrial production conditions,which leads to an asymmetric residual stress distribution.The spray quenching treatment was conducted on self-designed spray equipment,and the residual stress along the thickness direction was measured by a layer removal method based on deflections.Under the asymmetric spray quenching condition,the subsurface stress of the high-flow rate surface was lower than that of the low-flow rate surface,and the difference between the two subsurface stresses increased with the increase in the difference in water flow rates.The subsurface stress underneath the surface with a water flow rate of 0.60 m^(3)/h was 15.38 MPa less than that of 0.15 m^(3)/h.The simulated residual stress by finite element(FE)method of the high heat transfer coefficient(HTC)surface was less than that of the low HTC surface,which is consistent with the experimental results.The FE model can be used to analyze the strain and stress evolution and predict the quenched stress magnitude and distribution.
文摘The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the properties and microstructure of G115 steel was explored.The samples that were quenched and tempered twice had a higher tensile strength at room temperature and 650 ℃,and the impact energy was significantly improved.The strength and impact energy increased in proportion to the increase in the first quenching temperature.The microstructure differences between the single and double quenched and tempered samples were examined using metallographic microscopy and scanning electron microscopy.The grain size of the double quenched and tempered samples was finer than that of the single quenched and tempered samples, and the tempered martensite lath is more visible, as are the carbides and other precipitates, which are finer and more uniformly distributed.As the first quenching temperature increased, the grains became coarser but more uniform.
文摘Cu-Ni-Sn spinodal alloys(Spinodal bronze)are potential materials with robust applications in components associated with defence applications like bearings,propellers,bushes,and shafts of heavily loaded aircraft,off-road vehicles,and warships.This paper presents a comparative study using water,Brine solution,and SAE 40 oil as the quenching media in regular bronze(Cu-6Sn)and spinodal bronze(Cu-9Ni-6Sn)alloys.Morphological analysis was conducted by optical microscopy,transmission electron microscopy(TEM),and X-ray diffraction technique(XRD)on bronze and spinodal bronze samples immersed in the three different quenching media to understand the grain size and hardness values better.Tribological analysis was performed to analyze the effect of quenching media on the wear aspects of bronze and spinodal bronze samples.The hardness value of the brine-aged spinodal bronze samples was as high as 320 Hv,and the grain size was very low in the range of 60μm.A quantitative comparison between brine-aged regular bronze and brine-aged spinodal bronze showed that the hardness(Hv)was almost 80%higher for brine-aged spinodal bronze.Further,the grain size was approximately 30%finer for spinodal bronze when compared with regular bronze.When the load was increased in spinodal bronze samples,there was an initial dip in wear rate followed by a marginal increase.There was a steady increase in friction coefficient with a rise in load for brine-aged regular bronze and spinodal bronze samples.These results indicate that brine solution is the most effective quenching medium for cast Cu-Ni-Sn spinodal alloys.
文摘Multi-phase nitrides bonded silicon carbide lintel blocks were prepared using industrial SiC(SiC≥98 mass%,3-0.5,≤0.5 and≤0.044 mm),Si powder(Si≥98 mass%,≤0.044 mm),and SiO2 micropowder(SiO2≥96 mass%,d50=0.15 pm)as raw materials,and calcium lignosulfonate as the additive,batching,mixing,and molding on a vibration pressure molding machine,drying and then firing at 1420℃for 10 h in high-purity N2.The apparent porosity,the bulk density,the cold modulus of rupture,the hot modulus of rupture,and the linear expansion coefficient of the samples were tested.The phase composition and the microstructure of the samples at different nitriding depths(50,100,and 150 mm)were analyzed by XRD and SEM.The field application effects of the blocks were studied.The results show that:(1)the multi-phase nitrides bonded silicon carbide refractories can dynamically adjust their own phase composition and minimize structural and thermal stresses,improving the service life of key parts of dry quenching furnaces;(2)calcium lignosulfonate can improve the nitriding micro-environment of multi-phase nitrides bonded silicon carbide lintel blocks,successfully increasing the effective nitriding thickness of the blocks to 300 mm;(3)Sinosteel LI RR provides a unique concept in the design of materials and block types as well as the stable and scientific overall structure,promoting the industrialization process of dry quenching furnaces with long service life in China.
基金Project supported by the Natural Science Foundation of Zhejiang Province of China(Grant Nos.LQ22A040006,LY21A040004,LR22A040001,and LZ21A040001)the National Natural Science Foundation of China(Grant Nos.11835011 and 12074342).
文摘Manipulating nonlinear excitations,including solitons and vortices,is an essential topic in quantum many-body physics.A new progress in this direction is a protocol proposed in[Phys.Rev.Res.2043256(2020)]to produce dark solitons in a one-dimensional atomic Bose–Einstein condensate(BEC)by quenching inter-atomic interaction.Motivated by this work,we generalize the protocol to a two-dimensional BEC and investigate the generic scenario of its post-quench dynamics.For an isotropic disk trap with a hard-wall boundary,we find that successive inward-moving ring dark solitons(RDSs)can be induced from the edge,and the number of RDSs can be controlled by tuning the ratio of the after-and before-quench interaction strength across different critical values.The role of the quench played on the profiles of the density,phase,and sound velocity is also investigated.Due to the snake instability,the RDSs then become vortex–antivortex pairs with peculiar dynamics managed by the initial density and the after-quench interaction.By tuning the geometry of the box traps,demonstrated as polygonal ones,more subtle dynamics of solitons and vortices are enabled.Our proposed protocol and the discovered rich dynamical effects on nonlinear excitations can be realized in near future cold-atom experiments.
文摘The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required these days,it is necessary to predict the quality of heat treatment by CAE(Computer Added Engineering),shorten the product development period.The calculation of the vapor film collapses in a simple and practical time in order to improve the product performance.However,in the past,in order to formulate the vapor film collapse on a simulation,it was necessary to perform a very large amount of computational calculation CFD(computational fluid dynamics),which was a problem in terms of computer resources and the model of vapor film collapse.In addition,this phenomenon has a complexity behavior of the phenomenon in iterative processing,which also complicates the calculation.In this study,the vapor film collapse phenomenon is easily visualized using self-organized cellular automaton simulation which includes the phenomena of“vapor film thickness and its fluctuation”,“flow disturbance”,“surface step of workpiece”,and“decrease of cooling due to r shape of surface”.The average cooling state and repeated fluctuations of the cooling state were reproduced by this method.
基金supported by the Young Elite Scientists Sponsorship Program by China Association for Science and Technology (CAST) (No. YESS20160009)the National Natural Science Foundation of China (Nos. 31870023, 31571970 and 41506160)
文摘Quorum sensing(QS)is a regulatory system that regulates the behavior of microbial populations by sensing the concentration of signal molecules that are spontaneously produced and released by bacteria.The strategy of blocking the QS system and inhibiting the production of virulence factors is termed as quorum quenching(QQ).This strategy attenuates virulence without killing the pathogens,thereby weakening the selective pressure on pathogens and postponing the evolution of QQ-mediated drug resistance.In recent years,there have been significant theoretical and practical developments in the field of QS and QQ.In particular,with the development and utilization of marine resources,more and more marine microbial species have been found to be regulated by these two mechanisms,further promoting the research progress of QS and QQ.In this review,we described the diversity of QS signals and QS-related regulatory systems,and then introduced mechanisms related to QS interference,with particular emphasis on the description of natural QQ enzymes and chemicals acting as QS inhibitors.Finally,the exploitation of quorum sensing quenchers and the practical application of QQ were introduced,while some QQ strategies were proposed as promising tools in different fields such as medicine,aquaculture,agriculture and biological pollution prevention areas.
文摘A computer software to simulate the phase transformation during quenching is designed based on Avrami equation and Scheil additivity principle of incubation period. The isothermal transformation diagrams of supercooled austenite are described by cubic spline functions. This software is possess of a good graphic interface of Windows style, can simulate the whole process in austenite decomposition during continuous cooling. If the cooling rate was given, the fraction of various microstructures transformed of austenite decomposition during continuous cooling at any temperature can be calculated. The simulation results are checked with the quenching experiment of 45 steel. The results indicate that the simulation results are comparatively close to the experimental results.
文摘Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.
基金supported by the National Natural Science Foundation of China (No. 50471097)
文摘The characteristics of γ′ precipitates in a superalloy quenched from 1050°C at different rates were investigated using field emission scanning electron microscope(FESEM).When quenched from 1050°C, the size of primary aging γ′ precipitates has a small increase in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions and a drastic increase in the specimen that experienced a furnace-cooling-quenching condition.The cooling γ′ precipitates have unimodal distributions after quenching at the air-cooling rate and bimodal distributions after quenching at the furnace-cooling rate, but there are not these distributions in the specimens that experienced iced-brine-quenching and oil-quenching conditions.When aging at 760°C, the size of primary aging γ′ precipitates appears unaffected in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions.However, it has a drastic increase in the specimen that experienced a furnace-cooling-quenching condition, and it is interesting that the bigger cooling γ′ precipitates have a coalescence and octodendritic shape.The microhardness study indicates that the hardness has no variation in the specimens that experienced iced-brine-quenching, oil-quenching, and air-cooling-quenching conditions and has a drastic decrease in the specimens that experienced a furnace-cooling-quenching condition and obtains the minimum microhardness value 390.8 HV.
基金supported by the National Natural Science Foundation of China(No.20875059)
文摘The determination method of catechol by fluorescence quenching was developed.The assay was based on the combination of the unique property of gold nanoparticles with tyrosinase enzymatic reaction.In the presence of tyrosinase,the fluorescence of gold nanoparticles was quenched by catechol which can be employed to detect catechol.Under the optimal conditions,a linear range 5.0×10^(-7)-1.0×10^(-3) mol L^(-1) and a detection limit 1.0×10^(-7) mol L^(-1) of catechol were obtained.o-Quinone intermediate produ...
文摘In order to obtain the desired mechanical properties of quenching and tempering workpieces, as well as reduce the cracking tendency and distortion, a program of controllable quenching was established. Furthermore, a computer-aided quenching system (CAQ) was also developed. The application samples of the CAQ system showed satisfactory results.
基金This work was financially supported by National Natural Science Foundations of China (No.50131040)Key Technologies R & D Program of Inner Mongolia (No.20050205)College Scientific Research Project of Inner Mongolia (No.NJ05064).
文摘In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investigated. The obtained results show that the La2Mg(Ni0.85Co0.15)9M0.1 (M=B, Cr) alloy electrodes are composed of (La, Mg)Ni3 phase, LaNi5 phase and a small amount of the LaNi2 phase. A trace of the Ni2B phase exists in the as-cast MB alloy, and the Ni2B phase in the alloy nearly disappears after rapid quenching. Rapid quenching technology can slightly improve the cycling life of the alloy. When the quenching rate increases from 0 m·s-1 (As-cast is defined as quenching rate of 0 m·s-1) to 30 m·s-1, the cycle lives of the MB, MCr alloys enhance from 86 and 87 cycles to 106 and 119 cycles, respectively. On the other hand, the average capacity decay rates of the MB, MCr alloys decrease from 1.7172 and 1.7178 mAh·g-1·cycle-1 to 1.5751 and 1.3060 mAh·g-1·cycle-1 after 86 charge-discharges cycling, respectively.
文摘The effect of rare earth elements on quenching crack resistance of steel 9Cr2Mo was investigated by means of scanning electron microscopy (SEM) and optical microscopy. Experimental results show that, by adding RE elements to steel 9Cr2Mo, the number of quenching for crack initiation is increased. Meanwhile the propagation of quenching cracks is postponed and the paths of crack propagation are changed. Therefore, quenching crack resistance can be improved by adding RE elements to steel 9Cr2Mo.