Assessing mixing uniformity in microreactors via in-line spectroscopy

Mixing behavior is critical for enhancing the selectivity of fast chemical reactions in microreactors.A high Reynolds number(Re)improves the mixing rate and selectivity of the reactions,but some exceptions of increasing side product yield with the higher Re have been reported.This study investigated the mixing uniformity in microreactors with in-line UV-vis spectroscopy to clarify the relationship between reaction selectivity and chaotic mixing with the higher Re.A colorization experiment of thymolphthalein in an acidic solution was conducted with an excess acid amount to the base to indicate a non-uniformly mixed region.Non-uniformity significantly increased with Re.At the same time,the degree of mixing,which was measured by a usual decolorization experiment,showed that the mixing rate increased with Re.The in-line analysis of the Villermaux-Dushman reaction during the mixing clarified that side product yield significantly increased with Re at around 300 and then decreased at around 1100.These results suggest the compensation effect between the mixing uniformity and mixing rate on the selectivity of the mixing-sensitive reactions.Faster mixing,characterized by a larger Re,can disturb mixing uniformity and,in some cases,decrease reaction selectivity.

Life-Cycle Bearing Capacity for Pre-Stressed T-beams Based on Full-Scale Destructive Test

To investigate the evolution of load-bearing characteristics of pre-stressed beams throughout their service life and to provide a basis for accurately assessing the actual working state of damaged pre-stressed concrete T-beams,destructive tests were conducted on full-scale pre-stressed concrete beams.Based on the measurement and ana-lysis of beam deflection,strain,and crack development under various loading levels during the research tests,combined with the verification coefficient indicators specified in the codes,the verification coefficients of bridges at different stages of damage can be examined.The results indicate that the T-beams experience complete,incom-plete linear,and non-linear stages during the destructive test process.In the complete linear elastic stage,both the deflection and bottom strain verification coefficients comply with the specifications,indicating a good structural load-bearing capacity no longer adheres to the code’s requirements.In the non-linear stage,both coefficients exhi-bit a sharp increase,resulting in a further decrease in the structure’s load-bearing capacity.According to the pro-visions of the current code,the beam can be in the incomplete linear stage when both values fall within the code’s specified range.The strain verification coefficient sourced from the compression zone at the bottom of theflange is not recommended for assessing the bridge’s load-bearing capacity.

A new tube chamber system for evaluation of anterior chamber pressure during phacoemulsification tested in porcine eyes

AIM:To measure the optimal anterior chamber pressure(ACP)for safe phacoemulsification using a new tube chamber system with internal pressure measurement function in the porcine eye.METHODS:The 20-gauge and 21-gauge straight tips with yellow and orange sleeves,respectively,were covered by a test chamber combined with a pressure sensor for measuring ACP.This was measured for 20s from 10s after starting aspiration in the linear mode using vacuum levels of 200 and 150 mm Hg with a 20-gauge tip,and 300 and 250 mm Hg with a 21-gauge tip.Using a porcine eye,a pressure sensor fixed with a 0.9 mm corneal incision measured ACP.For the posterior capsule contact assay,porcine eyes were treated as described above,and the ultrasonic needle tip was held at the height of the iris and aspirated for 30s in linear mode at a vacuum of 200 and 150 mm Hg for the 20-gauge tip,and 300 and 250 mm Hg for the 21-gauge tip.The bottle height at which the posterior capsule accidentally contacted the ultrasonic tip was recorded,and the estimated ACP was calculated.RESULTS:The internal pressure of the new tube chamber system and ACP from the porcine eye closely matched proportional changes at vacuum levels of 200 and 150 mm Hg with 20-gauge tips.Similarly,proportional changes at vacuum levels of 300 and 250 mm Hg with the 21-gauge tip were nearly equal.The bottle height at which the posterior capsule contacted with the tip and estimated ACP were 57.5±12.6 cm(20.2±7.9 mm Hg)at 200 mm Hg with a 20-gauge tip,35.0±10.0 cm(16.6±6.3 mm Hg)at 150 mm Hg with a 20-gauge tip,47.5±12.6 cm(18.7±8.7 mm Hg)at 300 mm Hg with a 21-gauge tip,and 32.5±5.0 cm(15.7±3.5 mm Hg)at 250 mm Hg with a 21-gauge tip.CONCLUSION:A comprehensive understanding of this chamber system’s characteristics and usage can resolve anterior chamber instability caused by changing preoperative settings on the phaco machine.

Experimental Study on Coupled Cross-Flow and in-Line Vortex-Induced Vibration of Flexible Risers

In this work, we study the coupled cross-flow and in-line vortex-induced vibration （VIV） of a fixedly mounted flexible pipe, which is free to move in cross-flow （ Y- ） and in-line （ X- ） direction in a fluid flow where the mass and natural frequencies are precisely the same in both X- and Y-direction. The fluid speed varies from low to high with the corresponding vortex shedding frequency varying from below the first natural frequency to above the second natural frequency of the flexible pipe. Particular emphasis was placed on the investigation of the relationship between in-line and cross-flow vibration. The experimental results analyzed by using these measurements exhibits several valuable features.

The prediction on in-line vortex-induced vibration of slender marine structures

The in-line （IL） vortex-induced vibration （VIV） that occurs frequently in ocean engineering may cause severe fatigue damage in slender marine structures. To the best knowledge of the authors, in existing literatures, there is no efficient analytical model for predicting pure IL VIV. In this paper, a wake oscillator model capable of analyzing the IL VIV of slender marine structures has been developed. Two different kinds of van der Pol equations are used to describe the near wake dynamics related to the fluctuating nature of symmetric vortex shedding in the first excitation region and alternate vortex shedding in the second one. Some comparisons are carried out between the present model results and experimental data. It is found that many phenomena observed in experiments could be reproduced by the present wake oscillator model.

Ultrafiltration with in-line coagulation for the removal of natural humic acid and membrane fouling mechanism

Experimental and theoretical analysis were made on the natural humic acid removal and the membrane fouling of ultrafiltration （UF） with in-line coagulation. The results showed dissolved organic carbon （DOC） and UV254 removals by the UF with in-line coagulation at pH 7 were increased from 28% to 53% and 40% to 78% in comparison with direct UF treatment respectively. At the same time, the analysis of high performance liquid chromatography showed that UF with coagulation had significant improvement of removal of humic acid with molecular weights less than 6000 Da in particular. Compared to direct UF, the in-line coagulation UF also kept more constant permeate flux and very slight increase oftransmembrane pressure during a filtration circle. Two typical membrane fouling models were used by inducing two coefficients Kc and Kp corresponding to cake filtration model and pore narrowing model respectively. It was found that membrane fouling by pore-narrowing effect was effectively alleviated and that by cake-filtration was much decreased by in-line coagulation. Under the condition of coagulation prior to ultrafiltration at pH 7, the cake layer formed on the membrane surface became thicker, but the membrane filtration resistance was lower than that at pH 5 with the extension of operation time.

In-line response of vertical cylinders in regular and random waves

The in-line response of a vertical flexibly mounted cylinder in regular and random waves is reported. Both theoretical analyses and experimental measurements have been performed. The theoretical predictions are based on the Morison equation which is solved by the incremental harmonic balance method. Experiments are then performed in a wave flume to determine the accuracy of the Morison equation in predicting the in-line response of the cylinder in regular and random waves. The interaction between waves and vibrating cylinders are investigated.

Three-axis magnetic flux leakage in-line inspection simulation based on finite-element analysis

With the increase of pipelines, corrosion leakage accidents happen frequently. Therefore, nondestructive testing technology is important for ensuring the safe operation of the pipelines and energy mining. In this paper, the structure and principle of magnetic flux leakage （MFL） in-line inspection system is introduced first. Besides, a mathematic model of the system according to the ampere circuit rule, flux continuity theorem, and column coordinate transform is built, and the magnetic flux density in every point of space is calculated based on the theory of finite element analysis. Then we analyze and design the disposition of measurement section probes and sensors combining both three-axis MFL in-line inspection and multi-sensor fusion technology. Its advantage is that the three-axis changes of magnetic flux leakage field are measured by the multi-probes at the same time, so we can determine various defects accurately. Finally, the theory of finite element analysis is used to build a finite element simulation model, and the relationship between defects and MFL inspection signals is studied. Simulation and experiment results verify that the method not only enhances the detection ability to different types of defects but also improves the precision and reliability of the inspection system.

Nonlinear Coupled in-Line and Cross-Flow Vortex-Induced Vibration Analysis of Top Tensioned Riser

The fluctuating furces of the fluid exerted on the top terrsioned riser （＇FIR） in the in-line and cross-flow directions are both modeled by van del Pol wake oscillator model and the nonlinear coupled dynamics of the in-line and cross-flow vortex-induced vibrations （VIV） of the riser are analyzed in time domain in this papar. The numencal shnulation results of the riser＇s in-line and cross-flow displacements and curvatures are compared with experimental measurements and the comparison shows the validity of this method in modeling some main features of the riser＇s VIV. Finally, the effects of the riser＇s top tensions and internal flow velocities on the coupled vibrations of the riser are investigated.

Anisotropic total variation minimization approach in in-line phase-contrast tomography and its application to correction of ring artifacts

In-line phase-contrast computed tomography（IL-PC-CT） imaging is a new physical and biochemical imaging method.IL-PC-CT has advantages compared to absorption CT when imaging soft tissues. In practical applications, ring artifacts which will reduce the image quality are commonly encountered in IL-PC-CT, and numerous correction methods exist to either pre-process the sinogram or post-process the reconstructed image. In this study, we develop an IL-PC-CT reconstruction method based on anisotropic total variation（TV） minimization. Using this method, the ring artifacts are corrected during the reconstruction process. This method is compared with two methods： a sinogram preprocessing correction technique based on wavelet-FFT filter and a reconstruction method based on isotropic TV. The correction results show that the proposed method can reduce visible ring artifacts while preserving the liver section details for real liver section synchrotron data.

Determination of inorganic anions in ethyl acetate by in-line hollow fiber membrane extraction with ion chromatography

In this work, a novel hollow fiber membrane extractor was set up to extract inorganic anions from ethyl acetate using deionized water. Inorganic anions in slightly soluble organic solvents can be determined by the in-line hollow fiber membrane extractor coupled with ion chromatography at first time. Different aspects of the extraction procedure such as magnetic stirring speed, extraction flow rate and extraction time were optimized to achieve high extraction efficiency and good separation results. Satisfactory linear range, limits of detection and good repeatability were obtained. The procedure was applied to analyze inorganic anions in two commercial ethyl acetate samples.

Interactions between two in-line drops rising in pure glycerin

The behaviors of time-dependent interaction between two buoyancy-driven in-line deformable drops rising in pure glycerin at Re 〈 1 were studied, where the diameter for the leading drops ranged from 9.51 mm to 12.6 mm and for trailing drops from 12.7 mm to 15.8 mm. The situation while a larger drop chasing a smaller one was specifically considered which typically led to the smaller drop ＂coating＂ the larger one. Two approaches, the geometric feature approach and the energy change one, were used to judge the starting and ending times of the interaction between two drops. Based on a conical wake model, the drag coefficient of two approaching drops was calculated. Due to the approaching effect of the trailing drop, the leading drop was accelerated and the average drag coefficient was smaller than that for a free rising single drop. The frequency spectrums of the lateral oscillation of two drops during the interaction were obtained by using Fourier analysis. The oscillation frequency of the interactional drops was also different from that for a free rising single drop because of the wake effect produced by the leading drop. Due to a superposition of the drop shape oscillation and the drop internal circulation, the transverse oscillation frequencies of two drops have the same trend during the approaching process.

In-Line Inspection of Pipeline Defects Detection Using Ring-Type Laser

Pipeline plays a vital role in transporting fluids like oils, water, and petrochemical substances for longer distances. Based on the materials they carry, prolonged usage may cause the initiation of defects in the pipeline. These defects occur due to the formed salt deposits, chemical reaction happens between the inner surface and the transferring substance, prevailing environmental conditions, etc. These defects, if not identified earlier may lead to significant losses to the industry. In this work, an in-line inspection system utilizes the nondestructive way for analyzing the internal defects in the petrochemical pipeline. This system consists of a pipeline inspection robot having two major units namely the visual inspection unit and the power carrier unit. The visual inspection unit makes use of a ring-type laser diode and the camera. The laser diode serves as a light source for capturing good quality images of inspection. This unit is controlled by the Arduino in the power carrier unit which provides the necessary movement throughout the pipe. The inspected images captured by the camera are further processed with the aid of NI vision assistant software. After applying the processing function parameters provided by this software, the defect location can be clearly visualized with high precision. Three sets of defects are introduced in a Polylactide (PLA) pipe based on its position and angle along the circumference of the pipe. Further, this robot system serves as a real-time interactive image synchronization system for acquiring the inspected images. By comparing the actual and calculated defect size, the error percentage obtained was less than 5%.

昆明烟区土壤线虫数量与环境因子的Mantel Test分析

为进一步明确昆明烟区影响线虫的环境因素,于2022年采集云南昆明烟区8个县(市、区)64个乡镇的320个植烟土壤样品,调查与测定样品采集地的海拔、土壤线虫数量以及土壤理化性质(pH值及有机质、水解性氮、速效钾和有效磷含量),并探讨土壤线虫数量与植烟土壤环境因子之间的潜在关系。结果表明,昆明烟区土壤线虫数量一定程度上受到海拔及土壤理化性质的影响,海拔与有机质、水解性氮和速效钾呈显著正相关,pH值与有效磷呈极显著负相关,相关系数为-0.850;土壤线虫数量与土壤有效磷呈正相关,与海拔、pH值、有机质、水解性氮、速效钾呈负相关,其中与海拔、有机质和水解性氮的相关系数较大,分别为-0.751、-0.651和-0.568。通过Mantel test分析确定海拔、有机质和水解性氮含量是影响昆明烟区土壤线虫数量的重要因子。本结果可为有效防治土壤线虫提供科学依据。

STUDY ON AUTOMATIC IN-LINE MEASUREMENT OF FeO CONTENT IN AGGLOMERATE

In this paper, the mechanism of physical method for measuring the FeO content in agglomerate replacing the chemical method is proposed after studying the electromagnetic property of the agglomerate. The microcomputer-measuring system for FeO content is provided. Attention is also paid to introducing the working principle of the H-type compensation sensor and the processing method of the measured data. This system has been successfully applied in practice to in-line measure the FeO content.

In-line phase contrast for weakly absorbing materials with a microfocus x-ray source

For weakly absorbing materials, image contrast can be enhanced by phase contrast in formation. The effectiveness of the in-line phase contrast technique relies on its ability to record intensity data which contain information on the x- ray＇s phase shift. Four kinds of approaches to the relationship between intensity distribution and phase shift axe reviewed and discussed. A micro-focal x-ray source with high geometrical magnification is used to acquire phase contrast images. A great improvement on image quality is shown and geometrical parameters axe modified for comparison between different imaging positions.

Large Eddy Simulation on Interaction Between in-Line and Cross-Flow Oscillation of A Circular Cylinder

This paper discusses numerical results from three-dimensional large eddy simulations of an oscillating cylinder under prescribed movements in uniform flow. Six cases, namely pure in-line, pure cross-flow and two groups of ＇Figure of Eight＇ oscillation patterns are under investigation at Reynolds number Re = 24000. The ＇ Figure of Eight＇ pattern in each group is with identical shape but oppusite orbital directions. The numerical results on hydrodynamic forces, higher order force components, and vortex shedding modes are extensively studied and compared with the measured experimental data. It is found that the fluid force in phase with the velocity, which represents the energy transfer between the fluid and the cylinder, has opposite sign and different magnitude due to the opposite orbital direction. Higher order force components in cross-flow direction are found to occur at odd nmnber times of the oscillating frequency, while even nmbers dominate the higher order force components in in-llne direction. The 2C and 2T vortex shedding modes are well reproduced due to the opposite orbital direction effect. Comparisons between numerical and experimental results indicate that the present numerical model could be a rational tool for the identification of hydrodynamic coefficients which are normally applied in empirical models to predict the vortex-induced vibrations of slender marine structures.

Failure characterization of fully grouted rock bolts under triaxial testing

Confining stresses serve as a pivotal determinant in shaping the behavior of grouted rock bolts.Nonetheless,prior investigations have oversimplified the three-dimensional stress state,primarily assuming hydrostatic stress conditions.Under these conditions,it is assumed that the intermediate principal stress(σ_(2))equals the minimum principal stress(σ_(3)).This assumption overlooks the potential variations in magnitudes of in situ stress conditions along all three directions near an underground opening where a rock bolt is installed.In this study,a series of push tests was meticulously conducted under triaxial conditions.These tests involved applying non-uniform confining stresses(σ_(2)≠σ_(3))to cubic specimens,aiming to unveil the previously overlooked influence of intermediate principal stresses on the strength properties of rock bolts.The results show that as the confining stresses increase from zero to higher levels,the pre-failure behavior changes from linear to nonlinear forms,resulting in an increase in initial stiffness from 2.08 kN/mm to 32.51 kN/mm.The load-displacement curves further illuminate distinct post-failure behavior at elevated levels of confining stresses,characterized by enhanced stiffness.Notably,the peak load capacity ranged from 27.9 kN to 46.5 kN as confining stresses advanced from σ_(2)=σ_(3)=0 to σ_(2)=20 MPa and σ_(3)=10 MPa.Additionally,the outcomes highlight an influence of confining stress on the lateral deformation of samples.Lower levels of confinement prompt overall dilation in lateral deformation,while higher confinements maintain a state of shrinkage.Furthermore,diverse failure modes have been identified,intricately tied to the arrangement of confining stresses.Lower confinements tend to induce a splitting mode of failure,whereas higher loads bring about a shift towards a pure interfacial shear-off and shear-crushed failure mechanism.

Influence of tube voltage and current on in-line phase contrast imaging using a microfocus x-ray source

In-line x-ray phase contrast imaging has attracted much attention due to two major advantages： its effectiveness in imaging weakly absorbing materials, and the simplicity of its facilities. In this paper a comprehensive theory based on Wigner distribution developed by Wu and Liu [Med. Phys. 31 2378-2384 （2004）] is reviewed. The influence of x-ray source and detector on the image is discussed. Experiments using a microfocus x-ray source and a CCD detector are conducted, which show the role of two key factors on imaging： the tube voltage and tube current. High tube current and moderate tube voltage are suggested for imaging.

Unbound^(28)O,the heaviest oxygen isotope observed:a cutting-edge probe for testing nuclear models

The beyond-dripline oxygen isotopes^(27,28)O were recently observed at RIKEN,and were found to be unbound decaying into^(24)O by emitting neutrons.The unbound feature of the heaviest oxygen isotope,^(28)O,provides an excellent test for stateof-the-art nuclear models.The atomic nucleus is a self-organized quantum manybody system comprising specific numbers of protons Z and neutrons N.